SY56020R Low Voltage 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer 6.4Gbps with Equalization General Description The SY56020R is a fully-differential, low-voltage 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer with input equalization. The SY56020R can process clock signals as fast as 4.5GHz or data patterns up to 6.4Gbps. The differential input includes Micrel's unique, 3-pin input termination architecture that interfaces to CML differential signals, without any level-shifting or termination resistor networks in the signal path. The differential input can also accept AC-coupled LVPECL and LVDS signals. Input voltages as small as 200mV (400mVpp) are applied before the 9", 18" or 27" FR4 transmission line. For AC-coupled input interface applications, an internal voltage reference is provided to bias the VT pin. The outputs are CML, with extremely fast rise/fall times guaranteed to be less than 90ps. The SY56020R operates from a 2.5V 5% core supply and a 1.2V, 1.8V or 2.5V 5% output supply and is guaranteed over the full industrial temperature range (-40C to +85C). The SY56020R is part of Micrel's high-speed, Precision Edge(R) product line. Datasheets and support documentation can be found on Micrel's web site at: www.micrel.com. Functional Block Diagram Precision Edge(R) Features * 1.2V/1.8V/2.5V CML 1:4 Fanout Buffer * Equalizes 9, 18, 27 inches of FR4 * Guaranteed AC performance over temperature and voltage: - DC-to > 6.4Gbps Data throughput - DC-to > 4.5GHz Clock throughput - <280 ps propagation delay (IN-to-Q) - <15ps within-device skew - <90ps rise/fall times * Ultra-low jitter design - <1psRMS random jitter * High-speed CML outputs * 2.5V 5% VCC , 1.2/1.8V/2.5V 5% VCCO power supply operation * Industrial temperature range: -40C to +85C * Available in 16-pin (3mm x 3mm) QFN package Applications * * * * Data distribution SONET clock and data distribution Fiber Channel clock and data distribution Gigabit Ethernet clock and data distribution Markets * * * * * * Storage ATE Test and measurement Enterprise networking equipment High-end servers Metro area network equipment Precision Edge is a registered trademark of Micrel, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com November 2010 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Ordering Information Part Number Package Type Operating Range Package Marking Lead Finish SY56020RMG QFN-16 Industrial R020 with Pb-Free bar-line indicator NiPdAu Pb-Free SY56020RMGTR(2) QFN-16 Industrial R020 with Pb-Free bar-line indicator NiPdAu Pb-Free Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. Pin Configuration 16-Pin QFN Truth Table EQ Equalization FR4 6mil Stripline LOW 9" FLOAT 18" HIGH 27" November 2010 2 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Pin Description Pin Number Pin Name Pin Function IN, /IN Differential Input: Signals as small as 200mV VPK (400mVPP) applied to the input of 9, 18 or 27 inches 6mil FR4 stripline transmission line are then terminated with this differential input. Each input pin internally terminates with 50 to the VT pin. 1 VT Input Termination Center-Tap: Each side of the differential input pair terminates to VT pin. This pin provides a center-tap to a termination network for maximum interface flexibility. An internal high impedance resistor divider biases VT to allow input AC-coupling. For AC-coupling, bypass VT with 0.1F low-ESR capacitor to VCC. See "Interface Applications" subsection and Figure 2a. 4 EQ Three level input for equalization control. High, float, low. 16 VCC 8,13 VCCO Output Supply: Bypass with 0.1F//0.01F low-ESR capacitors as close to the VCCO pins as possible. Supplies the output buffers. 5 GND, Exposed pad Ground: Exposed pad must be connected to a ground plane that is the same potential as the ground pins. 15,14 Q0, /Q0 12,11 Q1, /Q1 10,9 Q2, /Q2 7,6 Q3, /Q3 2,3 November 2010 Positive Power Supply: Bypass with 0.1F//0.01F low-ESR capacitors as close to the VCC pins as possible. Supplies input and core circuitry. CML Differential Output Pairs: Differential buffered copy of the input signal. The output swing is typically 390mV. See "Interface Applications" subsection for termination information. 3 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC)............................... -0.5V to +3.0V Supply Voltage (VCCO) ............................. -0.5V to +3.0V VCC - VCCO ..............................................................<1.8V VCCO - VCC ..............................................................<0.5V Input Voltage (VIN) ....................................... -0.5V to VCC CML Output Voltage (VOUT)......................... 0.6V to 3.0V Current (VT) Source or Sink on VT pin.............................100mA Input Current Source or Sink Current on (IN, /IN) ...............50mA Maximum Operating Junction Temperature.......... 125C Lead Temperature (soldering, 20sec.).................. 260C Storage Temperature (Ts) ....................-65C to +150C Supply Voltage (Vcc) .................................. 2.375V to 2.625V (Vcco) ................................... 1.14V to 2.625V Ambient Temperature (TA)............................-40C to +85C Package Thermal Resistance(3) QFN Still-Air (JA)..............................................................75C/W Junction-to-Board (JB) ............................................33C/W DC Electrical Characteristics(4) TA = -40C to +85C, unless otherwise stated. Symbol Parameter Condition Min. Typ. Max. Units Power Supply Voltage Range VCC VCCO VCCO VCCO 2.375 1.14 1.7 2.375 2.5 1.2 1.8 2.5 2.625 1.26 1.9 2.625 V Power Supply Current Maximum VCC. 60 85 mA ICCO Power Supply Current No Load. Maximum VCCO. 64 84 mA RIN Input Resistance (IN-to-VT, /IN-to-VT ) 45 50 55 RDIFF_IN Differential Input Resistance (IN-to-/IN) 90 100 110 VIH Input HIGH Voltage (IN, /IN) IN, /IN 1.42 VCC V VIL Input LOW Voltage (IN, /IN) IN, /IN 1.22V = 1.7-0.475 1.22 VIH-0.2 V VIN Input Voltage Swing (IN, /IN) See Figure 3a, applied to input of transmission line. 0.2 1.0 V VDIFF_IN Differential Input Voltage Swing (|IN - /IN|) See Figure 3b, applied to input of transmission line. 0.4 2.0 V VT_IN Voltage from Input to VT 1.28 V VCC ICC Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the PCB. JB and JA values are determined for a 4-layer board in still-air number, unless otherwise stated. 4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. November 2010 4 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R CML Outputs DC Electrical Characteristics(5) VCCO = 1.14V to 1.26V RL = 50 to VCCO, VCCO = 1.7V to 1.9V, 2.375V to 2.625V, RL = 50 to VCCO or 100 across the outputs. VCC = 2.375V to 2.625V; TA = -40C to +85C, unless otherwise stated. Symbol Parameter Condition VOH Output HIGH Voltage RL = 50 to VCCO VOUT Output Voltage Swing Differential Output Voltage Swing VDIFF_OU T ROUT Min. Typ. Max. Units VCC - 0.020 VCC - 0.010 VCC V See Figure 3a 300 390 475 mV See Figure 3b 600 780 950 mV 45 50 55 Min. Typ. Output Source Impedance Three Level EQ Input DC Electrical Characteristics(5) VCC = 2.375V to 2.625V; TA = -40C to +85C, unless otherwise stated. Symbol Parameter Max. Units VIH Input HIGH Voltage Condition VCC - 0.3 VCC V VIL Input LOW Voltage 0 VEE + 0.3 V IIH Input HIGH Current VIH = VCC 400 A IIL Input LOW Current VIL = GND -480 A Note: 5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. AC Electrical Characteristics VCCO = 1.14V to 1.26V RL = 50 to VCCO, VCCO = 1.7V to 1.9V, 2.375V to 2.625V, RL = 50 to VCCO or 100 across the outputs, VCC = 2.375V to 2.625V; TA = -40C to +85C, unless otherwise stated. Symbol Parameter fMAX Maximum Frequency tPD Propagation Delay Condition Min. NRZ Data 6.4 VOUT > 200mV IN-to-Q Clock Note 6, Figure 1 Typ. Max. Gbps 4.5 100 Units GHz 180 280 ps 3 15 ps Output-to-Output Skew Note 7 Part-to-Part Skew Note 8 100 ps tJitter Random Jitter Note 9 1 psRMS tr tf Output Rise/Fall Time (20% to 80%) At full output swing. 90 ps tSkew 20 50 Notes: 6. Propagation delay is measured with no attenuating transmission line connected to the input. 7. Output-to-Output skew is the difference in time between both outputs, receiving data from the same input, for the same temperature, voltage and transition. 8. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and no skew at the edges at the respective inputs. 9. Random jitter is measured with a K28.7 pattern, measured at fMAX. November 2010 5 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Interface Applications For Input Interface Applications see Figures 4a-e and for CML Output Termination, see Figures 5a-d. CML Output Termination with VCCO 1.2V For VCCO of 1.2V, Figure 5a, terminate the output with 50 to 1.2V, DC coupled, not 100 differentially across the outputs. If AC-coupling is used, Figure 5d, terminate into 50 to 1.2V before the coupling capacitor and then connect to a high value resistor to a reference voltage. Do not AC-couple with internally terminated receiver. For example, 50 ANY-IN input. AC-coupling will offset the output voltage by 200mV and this offset voltage will be too low for proper driver operation. Any unused output pair needs to be terminated when VCCO is 1.2V, do not leave floating. CML Output Termination with VCCO 1.8V, 2.5V For VCCO of 1.8V, Figure 5a and Figure 5b, terminate either with 50 ohms to VCCO or 100 ohms differentially across the outputs. AC- or DC-coupling is fine. For best signal integrity, terminate any unused output pairs. Input Termination From 1.8V CML driver: Terminate input with VT tied to 1.8V. Don't terminate 100 ohms differentially. From 2.5V CML driver: Terminate input with either VT tied to 2.5V or 100 ohms differentially. The input cannot be DC-coupled from a 1.2V CML driver. Input AC-Coupling The SY56020R input can accept AC-coupling from any driver. Bypass VT with a 0.1F low-ESR capacitor to VCC as shown in Figures 4c and 4d. VT has an internal high impedance resistor divider as shown in Figure 2a, to provide a bias voltage for AC-coupling. Timing Diagrams Figure 1. Propagation Delay Figure 1. Propagation Delay November 2010 6 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Typical Characteristics VCC = 2.5, VCCO = 1.2V, GND = 0V, VIN = 400mV, RL = 50 to 1.2V, Data Pattern: 223-1, TA = 25C, unless otherwise stated. November 2010 7 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Input and Output Stage Figure 2a. Simplified Differential Input Buffer Figure 2b. Simplified CML Output Buffer Single-Ended and Differential Swings Figure 3a. Single-Ended Swing November 2010 Figure 3b. Differential Swing 8 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Input Interface Applications Figure 4a. CML Interface (DC-Coupled, 1.8V, 2.5V) Option: May connect VT to VCC Figure 4b. CML Interface (DC-Coupled, 1.8V, 2.5V) Figure 4d. LVPECL Interface (AC-Coupled) Figure 4e. LVPECL Interface (DC-Coupled) November 2010 9 Figure 4c. CML Interface (AC-Coupled) M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R CML Output Termination Figure 5a. 1.2V, 1.8V or 2.5V CML DC-Coupled Termination Figure 5b. 1.8V or 2.5V CML DC-Coupled Termination Figure 5d. CML AC-Coupled Termination (VCCO 1.2V only) Figure 5c. CML AC-Coupled Termination (VCCO 1.8V or 2.5V) Related Product and Support Documents Part Number Function Datasheet Link HBW Solutions New Products and Termination Application Notes http://www.micrel.com/page.do?page=/product-info/as/HBWsolutions.shtml November 2010 10 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY56020R Package Information 16-Pin QFN MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2008 Micrel, Incorporated. November 2010 11 M9999-111810-A hbwhelp@micrel.com or (408) 955-1690