Order this document by MRF176GU/D SEMICONDUCTOR TECHNICAL DATA The RF MOSFET Line N-Channel Enhancement-Mode Designed for broadband commercial and military applications using push pull circuits at frequencies to 500 MHz. The high power, high gain and broadband performance of these devices makes possible solid state transmitters for FM broadcast or TV channel frequency bands. * Electrical Performance MRF176GU @ 50 V, 400 MHz ("U" Suffix) Output Power -- 150 Watts Power Gain -- 14 dB Typ Efficiency -- 50% Typ MRF176GV @ 50 V, 225 MHz ("V" Suffix) Output Power -- 200 Watts Power Gain -- 17 dB Typ Efficiency -- 55% Typ 200/150 W, 50 V, 500 MHz N-CHANNEL MOS BROADBAND RF POWER FETs D * 100% Ruggedness Tested At Rated Output Power * Low Thermal Resistance * Low Crss -- 7.0 pF Typ @ VDS = 50 V G S (FLANGE) G CASE 375-04, STYLE 2 D MAXIMUM RATINGS Symbol Value Unit Drain-Source Voltage Rating VDSS 125 Vdc Gate-Source Voltage VGS 40 Vdc Drain Current -- Continuous ID 16 Adc Total Device Dissipation @ TC = 25C Derate above 25C PD 400 2.27 Watts W/C Storage Temperature Range Tstg - 65 to +150 C TJ 200 C Symbol Max Unit RJC 0.44 C/W Operating Junction Temperature THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction to Case Handling and Packaging -- MOS devices are susceptible to damage from electrostatic charge. Reasonable precautions in handling and packaging MOS devices should be observed. ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted) Symbol Min Typ Max Unit V(BR)DSS 125 -- -- Vdc Zero Gate Voltage Drain Current (VDS = 50 V, VGS = 0) IDSS -- -- 2.5 mAdc Gate-Body Leakage Current (VGS = 20 V, VDS = 0) IGSS -- -- 1.0 Adc Characteristic OFF CHARACTERISTICS (1) Drain-Source Breakdown Voltage (VGS = 0, ID = 100 mA) NOTE: 1. Each side of device measured separately. REV 8 RF DEVICE DATA MOTOROLA Motorola, Inc. 1995 MRF176GU MRF176GV 1 ELECTRICAL CHARACTERISTICS -- continued (TC = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit Gate Threshold Voltage (VDS = 10 V, ID = 100 mA) VGS(th) 1.0 3.0 6.0 Vdc Drain-Source On-Voltage (VGS = 10 V, ID = 5.0 A) VDS(on) 1.0 3.0 5.0 Vdc Forward Transconductance (VDS = 10 V, ID = 2.5 A) gfs 2.0 3.0 -- mhos Input Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Ciss -- 180 -- pF Output Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Coss -- 100 -- pF Reverse Transfer Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Crss -- 6.0 -- pF Common Source Power Gain (VDD = 50 Vdc, Pout = 200 W, f = 225 MHz, IDQ = 2.0 x 100 mA) Gps 15 17 -- dB Drain Efficiency (VDD = 50 Vdc, Pout = 200 W, f = 225 MHz, IDQ = 2.0 x 100 mA) 50 55 -- % Electrical Ruggedness (VDD = 50 Vdc, Pout = 200 W, f = 225 MHz, IDQ = 2.0 x 100 mA, VSWR 10:1 at all Phase Angles) ON CHARACTERISTICS (1) DYNAMIC CHARACTERISTICS (1) FUNCTIONAL CHARACTERISTICS -- MRF176GV (2) (Figure 1) No Degradation in Output Power NOTES: 1. Each side of device measured separately. 2. Measured in push-pull configuration. R1 BIAS 0 - 6 V C8 C3 C10 C9 C4 D.U.T. R2 + 50 V - T2 T1 C5 C1 C6 C2 C1 -- Arco 404, 8.0 - 60 pF C2, C3, C6, C8 -- 1000 pF Chip C4, C9 -- 0.1 F Chip C5 -- 180 pF Chip C7 -- Arco 403, 3.0 - 35 pF C10 -- 0.47 F Chip, Kemet 1215 or Equivalent L1 -- 10 Turns AWG #16 Enameled Wire, L1 -- Close Wound, 1/4 I.D. Board material -- .062 fiberglass (G10), Two sided, 1 oz. copper, r 5 ^ Unless otherwise noted, all chip capacitors are ATC Type 100 or Equivalent C7 L2 -- Ferrite Beads of Suitable Material L2 -- for 1.5 - 2.0 H, Total Inductance R1 -- 100 Ohms, 1/2 W R2 -- 1.0 kOhms, 1/2 W T1 -- 4:1 Impedance Ratio RF Transformer. T1 -- Can Be Made of 25 Ohm Semirigid T1 -- Co-Ax, 47 - 62 Mils O.D. T2 -- 1:4 Impedance Ratio RF Transformer. T2 -- Can Be Made of 25 Ohm Semirigid T2 -- Co-Ax, 62 - 90 Mils O.D. NOTE: For stability, the input transformer T1 should be loaded NOTE: with ferrite toroids or beads to increase the common NOTE: mode inductance. For operation below 100 MHz. The NOTE: same is required for the output transformer. Figure 1. 225 MHz Test Circuit MRF176GU MRF176GV 2 MOTOROLA RF DEVICE DATA ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit Common Source Power Gain (VDD = 50 Vdc, Pout = 150 W, f = 400 MHz, IDQ = 2.0 x 100 mA) Gps 12 14 -- dB Drain Efficiency (VDD = 50 Vdc, Pout = 150 W, f = 400 MHz, IDQ = 2.0 x 100 mA) 45 50 -- % Electrical Ruggedness (VDD = 50 Vdc, Pout = 150 W, f = 400 MHz, IDQ = 2.0 x 100 mA, VSWR 10:1 at all Phase Angles) FUNCTIONAL CHARACTERISTICS -- MRF176GU (1) (Figure 2) No Degradation in Output Power NOTE: 1. Measured in push-pull configuration. A B L7 C17 C18 L8 BIAS C11 C12 R1 C13 C19 C15 50 V R2 C9 L1 Z1 Z3 L3 C1 B1 C3 C6 C5 C4 C8 B2 C7 C10 L2 Z2 Z4 C2 L4 D.U.T. L6 R3 A B C14 B1 -- Balun, 50 Semirigid Coax .086 OD 2 Long B2 -- Balun, 50 Semirigid Coax .141 OD 2 Long C1, C2, C9, C10 -- 270 pF ATC Chip Capacitor C3 -- 15 pF ATC Chip Cap C4, C8 -- 1.0 - 20 pF Piston Trimmer Cap C5 -- 27 pF ATC Chip Cap C6, C7 -- 22 pF Mini Unelco Capacitor C11, C13, C14, C15, C16 -- 0.01 F Ceramic Capacitor C12 -- 1.0 F 50 V Tantalum Cap C17, C18 -- 680 pF Feedthru Capacitor .200 C19 -- 10 F 100 V Tantalum Cap L1, L2 -- Hairpin Inductor #18 W L3, L4 -- Hairpin Inductor #18 W .200 C16 .400 .200 L5, L6 -- 13T #18 W .250 ID L7 -- Ferroxcube VK-200 20/4B L8 -- 3T #18 W .340 ID R1 -- 1.0 k 1/4 W Resistor R2, R3 -- 10 k 1/4 W Resistor Z1, Z2 -- Microstrip Line .400L x .250W Z3, Z4 -- Microstrip Line .450L x .250W Ckt Board Material -- .060 teflon-fiberglass, copper clad both sides, 2 oz. copper, r = 2.55 Figure 2. 400 MHz Test Circuit MOTOROLA RF DEVICE DATA MRF176GU MRF176GV 3 TYPICAL CHARACTERISTICS 100 VDS = 30 V I D, DRAIN CURRENT (AMPS) f T, UNITY GAIN-FREQUENCY (MHz) 4000 3000 15 V 2000 1000 0 0 1 2 3 4 5 6 7 ID, DRAIN CURRENT (AMPS) 8 9 10 TC = 25C 1 10 2 Figure 3. Common Source Unity Current Gain* Gain-Frequency versus Drain Current 10 50 VDS, DRAIN-SOURCE VOLTAGE (VOLTS) 200 Figure 4. DC Safe Operating Area * Data shown applies to each half of MRF176GU/GV INPUT AND OUTPUT IMPEDANCE MRF176GU/GV VDD = 50 V, IDQ = 2 x 100 mA f MHz Zin 400 300 f = 500 MHz f = 500 MHz 400 ZOL* 225 100 225 300 400 500 2.05 - j2.50 2.00 - j1.10 1.85 + j0.75 1.60 + j2.70 30 50 100 150 225 7.50 - j6.50 5.50 - j7.00 3.20 - j6.00 2.50 - j4.80 2.05 - j2.50 150 ZOL* 6.50 - j3.50 4.80 - j3.10 3.00 - j1.90 2.60 + j0.10 (Pout = 200 W) 300 225 50 ZOL* OHMS (Pout = 150 W) 225 150 Zin OHMS 17.00 - j4.00 14.00 - j5.00 11.00 - j5.20 8.20 - j5.00 5.00 - j4.20 30 100 Zo = 10 50 30 ZOL* = Conjugate of the optimum load impedance into which the device output operates at a given output power, voltage and frequency. NOTE: Input and output impedance values given are measured from gate to gate and drain to drain respectively. Figure 5. Series Equivalent Input/Output Impedance MRF176GU MRF176GV 4 MOTOROLA RF DEVICE DATA TYPICAL CHARACTERISTICS 30 200 Ciss 100 Coss 25 Pout = 200 W 50 POWER GAIN (dB) C, CAPACITANCE (pF) 500 VGS = 0 V f = 1 MHz 20 5 0 15 150 W VDS = 50 V IDQ = 2 x 100 mA 10 Crss 10 20 10 20 30 40 VDS, DRAIN-SOURCE VOLTAGE (VOLTS) 5 50 10 5 Figure 6. Capacitance versus Drain-Source Voltage* 20 50 100 f, FREQUENCY (MHz) 200 500 Figure 7. Power Gain versus Frequency * Data shown applies to each half of MRF176GU/GV MRF176GV 320 Pout , OUTPUT POWER (WATTS) Pout, POWER OUTPUT (WATTS) 300 VDD = 50 V 200 40 V 100 IDQ = 2 x 100 mA f = 225 MHz 280 IDQ = 2 x 100 mA f = 225 MHz 240 Pin = 6 W 200 4W 160 120 2W 80 40 0 0 6 Pin, POWER INPUT (WATTS) Figure 8. Power Input versus Power Output MOTOROLA RF DEVICE DATA 12 0 30 32 34 36 38 40 42 44 VDS, SUPPLY VOLTAGE (VOLTS) 46 48 50 Figure 9. Output Power versus Supply Voltage MRF176GU MRF176GV 5 200 200 180 180 160 Pout , OUTPUT POWER (WATTS) Pout , OUTPUT POWER (WATTS) TYPICAL CHARACTERISTICS MRF176GU f = 400 MHz 140 120 500 MHz 100 80 60 VDD = 40 V IDQ = 2 x 100 mA 40 20 0 0 2 4 6 8 10 12 Pin, INPUT POWER (WATTS) 14 Figure 10. Output Power versus Input Power f = 400 MHz 160 500 MHz 140 120 100 80 60 VDD = 50 V IDQ = 2 x 100 mA 40 20 16 0 0 2 4 6 8 10 12 Pin, INPUT POWER (WATTS) 14 16 Figure 11. Output Power versus Input Power Pout , OUTPUT POWER (WATTS) 200 Pin = 12 W 180 8W 160 140 4W 120 100 80 60 40 IDQ = 2 x 100 mA f = 400 MHz 20 0 20 30 40 VDD, SUPPLY VOLTAGE (VOLTS) 50 Figure 12. Output Power versus Supply Voltage MRF176GU MRF176GV 6 MOTOROLA RF DEVICE DATA RF POWER MOSFET CONSIDERATIONS MOSFET CAPACITANCES The physical structure of a MOSFET results in capacitors between the terminals. The metal oxide gate structure determines the capacitors from gate-to-drain (Cgd), and gate-to- source (Cgs). The PN junction formed during the fabrication of the MOSFET results in a junction capacitance from drain- to-source (Cds). These capacitances are characterized as input (Ciss), output (Coss) and reverse transfer (Crss) capacitances on data sheets. The relationships between the inter-terminal capacitances and those given on data sheets are shown below. The Ciss can be specified in two ways: 1. Drain shorted to source and positive voltage at the gate. 2. Positive voltage of the drain in respect to source and zero volts at the gate. In the latter case the numbers are lower. However, neither method represents the actual operating conditions in RF applications. DRAIN Cgd GATE Cds Cgs Ciss = Cgd + Cgs Coss = Cgd + Cds Crss = Cgd SOURCE The Ciss given in the electrical characteristics table was measured using method 2 above. It should be noted that Ciss, Coss, Crss are measured at zero drain current and are provided for general information about the device. They are not RF design parameters and no attempt should be made to use them as such. LINEARITY AND GAIN CHARACTERISTICS In addition to the typical IMD and power gain, data presented in Figure 3 may give the designer additional information on the capabilities of this device. The graph represents the small signal unity current gain frequency at a given drain current level. This is equivalent to fT for bipolar transistors. Since this test is performed at a fast sweep speed, heating of the device does not occur. Thus, in normal use, the higher temperatures may degrade these characteristics to some extent. DRAIN CHARACTERISTICS One figure of merit for a FET is its static resistance in the full-on condition. This on-resistance, VDS(on), occurs in the linear region of the output characteristic and is specified under specific test conditions for gate-source voltage and drain current. For MOSFETs, VDS(on) has a positive temperature coefficient and constitutes an important design consideration at high temperatures, because it contributes to the power dissipation within the device. GATE CHARACTERISTICS The gate of the MOSFET is a polysilicon material, and is electrically isolated from the source by a layer of oxide. The input resistance is very high -- on the order of 109 ohms -- resulting in a leakage current of a few nanoamperes. MOTOROLA RF DEVICE DATA Gate control is achieved by applying a positive voltage slightly in excess of the gate-to-source threshold voltage, VGS(th). Gate Voltage Rating -- Never exceed the gate voltage rating (or any of the maximum ratings on the front page). Exceeding the rated VGS can result in permanent damage to the oxide layer in the gate region. Gate Termination -- The gates of this device are essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the devices due to voltage build-up on the input capacitor due to leakage currents or pickup. Gate Protection -- This device does not have an internal monolithic zener diode from gate-to-source. The addition of an internal zener diode may result in detrimental effects on the reliability of a power MOSFET. If gate protection is required, an external zener diode is recommended. HANDLING CONSIDERATIONS The gate of the MOSFET, which is electrically isolated from the rest of the die by a very thin layer of SiO2, may be damaged if the power MOSFET is handled or installed improperly. Exceeding the 40 V maximum gate-to-source voltage rating, VGS(max), can rupture the gate insulation and destroy the FET. RF Power MOSFETs are not nearly as susceptible as CMOS devices to damage due to static discharge because the input capacitances of power MOSFETs are much larger and absorb more energy before being charged to the gate breakdown voltage. However, once breakdown begins, there is enough energy stored in the gate-source capacitance to ensure the complete perforation of the gate oxide. To avoid the possibility of device failure caused by static discharge, precautions similar to those taken with small-signal MOSFET and CMOS devices apply to power MOSFETs. When shipping, the devices should be transported only in antistatic bags or conductive foam. Upon removal from the packaging, careful handling procedures should be adhered to. Those handling the devices should wear grounding straps and devices not in the antistatic packaging should be kept in metal tote bins. MOSFETs should be handled by the case and not by the leads, and when testing the device, all leads should make good electrical contact before voltage is applied. As a final note, when placing the FET into the system it is designed for, soldering should be done with grounded equipment. The gate of the power MOSFET could still be in danger after the device is placed in the intended circuit. If the gate may see voltage transients which exceed VGS(max), the circuit designer should place a 40 V zener across the gate and source terminals to clamp any potentially destructive spikes. Using a resistor to keep the gate-to-source impedance low also helps damp transients and serves another important function. Voltage transients on the drain can be coupled to the gate through the parasitic gate-drain capacitance. If the gate-to-source impedance and the rate of voltage change on the drain are both high, then the signal coupled to the gate may be large enough to exceed the gate-threshold voltage and turn the device on. DESIGN CONSIDERATIONS The MRF176G is a RF power N-channel enhancement mode field-effect transistor (FETs) designed for VHF and MRF176GU MRF176GV 7 UHF power amplifier applications. Motorola RF MOSFETs feature a vertical structure with a planar design, thus avoiding the processing difficulties associated with V-groove MOS power FETs. Motorola Application Note AN211A, FETs in Theory and Practice, is suggested reading for those not familiar with the construction and characteristics of FETs. The major advantages of RF power FETs include high gain, low noise, simple bias systems, relative immunity from thermal runaway, and the ability to withstand severely mismatched loads without suffering damage. Power output can be varied over a wide range with a low power dc control signal, thus facilitating manual gain control, ALC and modulation. DC BIAS The MRF176G is an enhancement mode FET and, therefore, does not conduct when drain voltage is applied. Drain MRF176GU MRF176GV 8 current flows when a positive voltage is applied to the gate. RF power FETs require forward bias for optimum performance. The value of quiescent drain current (IDQ) is not critical for many applications. The MRF176G was characterized at IDQ = 100 mA, each side, which is the suggested minimum value of IDQ. For special applications such as linear amplification, IDQ may have to be selected to optimize the critical parameters. The gate is a dc open circuit and draws no current. Therefore, the gate bias circuit may be just a simple resistive divider network. Some applications may require a more elaborate bias sytem. GAIN CONTROL Power output of the MRF176 may be controlled from its rated value down to zero (negative gain) by varying the dc gate voltage. This feature facilitates the design of manual gain control, AGC/ALC and modulation systems. MOTOROLA RF DEVICE DATA PACKAGE DIMENSIONS U G 1 Q RADIUS 2 PL 0.25 (0.010) M T A B M 2 DIM A B C D E G H J K N Q R U -B- R 5 K M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 4 D N E J H -T- -A- SEATING PLANE C STYLE 2: PIN 1. 2. 3. 4. 5. INCHES MIN MAX 1.330 1.350 0.370 0.410 0.190 0.230 0.215 0.235 0.050 0.070 0.430 0.440 0.102 0.112 0.004 0.006 0.185 0.215 0.845 0.875 0.060 0.070 0.390 0.410 1.100 BSC MILLIMETERS MIN MAX 33.79 34.29 9.40 10.41 4.83 5.84 5.47 5.96 1.27 1.77 10.92 11.18 2.59 2.84 0.11 0.15 4.83 5.33 21.46 22.23 1.52 1.78 9.91 10.41 27.94 BSC DRAIN DRAIN GATE GATE SOURCE CASE 375-04 ISSUE D MOTOROLA RF DEVICE DATA MRF176GU MRF176GV 9 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://motorola.com/sps MRF176GU MRF176GV 10 MRF176GU/D MOTOROLA RF DEVICE DATA