INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: * The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications * The IC06 74HC/HCT/HCU/HCMOS Logic Package Information * The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines 74HC/HCT175 Quad D-type flip-flop with reset; positive-edge trigger Product specification Supersedes data of December 1990 File under Integrated Circuits, IC06 1998 Jul 08 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 The 74HC/HCT175 have four edge-triggered, D-type flip-flops with individual D inputs and both Q and Q outputs. The common clock (CP) and master reset (MR) inputs load and reset (clear) all flip-flops simultaneously. The state of each D input, one set-up time before the LOW-to-HIGH clock transition, is transferred to the corresponding output (Qn) of the flip-flop. FEATURES * Four edge-triggered D flip-flops * Output capability: standard * ICC category: MSI GENERAL DESCRIPTION The 74HC/HCT175 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. All Qn outputs will be forced LOW independently of clock or data inputs by a LOW voltage level on the MR input. The device is useful for applications where both the true and complement outputs are required and the clock and master reset are common to all storage elements. QUICK REFERENCE DATA GND = 0 V; Tamb = 25 C; tr = tf = 6 ns TYPICAL SYMBOL tPHL PARAMETER UNIT HC HCT CP to Qn, Qn 17 16 ns MR to Qn 15 19 ns CP to Qn, Qn 17 16 ns MR to Qn 15 16 ns propagation delay tPLH CONDITIONS CL = 15 pF; VCC = 5 V propagation delay fmax maximum clock frequency 83 54 MHz CI input capacitance 3.5 3.5 pF CPD power dissipation capacitance per flip-flop notes 1 and 2 32 34 pF Notes 1. CPD is used to determine the dynamic power dissipation (PD in W): PD = CPD x VCC2 x fi + (CL x VCC2 x fo) where: fi = input frequency in MHz fo = output frequency in MHz (CL x VCC2 x fo) = sum of outputs CL = output load capacitance in pF VCC = supply voltage in V 2. For HC the condition is VI = GND to VCC For HCT the condition is VI = GND to VCC - 1.5 V 1998 Jul 08 2 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 ORDERING INFORMATION PACKAGE TYPE NUMBER NAME DESCRIPTION VERSION 74HC175N; 74HCT175N DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 74HC175D; 74HCT175D SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 74HC175DB; 74HCT175DB SSOP16 74HC175PW; 74HCT175PW TSSOP16 PIN DESCRIPTION PIN NO. SYMBOL NAME AND FUNCTION 1 MR master reset input (active LOW) 2, 7, 10, 15 Q0 to Q3 flip-flop outputs 3, 6, 11, 14 Q0 to Q3 complementary flip-flop outputs 4, 5, 12, 13 D0 to D3 data inputs 8 GND ground (0 V) 9 CP clock input (LOW-to-HIGH, edge-triggered) 16 VCC positive supply voltage Fig.1 Pin configuration. 1998 Jul 08 Fig.2 Logic symbol. 3 Fig.3 IEC logic symbol. Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger Fig.4 Functional diagram. FUNCTION TABLE INPUTS OUTPUTS OPERATING MODES MR CP Dn Qn Qn reset (clear) L X load "1" H X L H h H L load "0" H I L H Note 1. H = HIGH voltage level h = HIGH voltage level one set-up time prior to the LOW-to-HIGH CP transition L = LOW voltage level I = LOW voltage level one set-up time prior to the LOW-to-HIGH CP transition = LOW-to-HIGH CP transition X = don't care Fig.5 Logic diagram. 1998 Jul 08 4 74HC/HCT175 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 DC CHARACTERISTICS FOR 74HC For the DC characteristics see "74HC/HCT/HCU/HCMOS Logic Family Specifications". Output capability: standard ICC category: MSI AC CHARACTERISTICS FOR 74HC GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (C) TEST CONDITIONS 74HC SYMBOL PARAMETER +25 min. tPHL/ tPLH tPHL/ tPLH tTHL/ tTLH tW tW trem tsu th fmax 1998 Jul 08 propagation delay CP to Qn, Qn propagation delay MR to Qn, Qn output transition time clock pulse width HIGH or LOW set-up time Dn to CP hold time CP to Dn maximum clock pulse frequency -40 to +125 min. UNIT VCC (V) WAVEFORMS 2.0 Fig.6 typ. max. min. max. max. 55 175 220 265 20 35 44 53 4.5 16 30 37 45 6.0 50 150 190 225 18 30 38 45 4.5 14 26 33 38 6.0 19 75 95 110 7 15 19 22 4.5 6 13 16 19 6.0 ns ns ns ns 2.0 2.0 80 22 100 120 16 8 20 24 4.5 14 6 17 20 6.0 19 100 120 master reset pulse width 80 LOW 16 removal time MR to CP -40 to +85 ns 2.0 2.0 7 20 24 4.5 14 6 17 20 6.0 5 -33 5 5 5 -12 5 5 4.5 5 -10 5 5 6.0 80 3 100 120 16 1 20 24 4.5 14 1 17 20 6.0 25 2 30 40 5 0 6 8 4.5 4 0 5 7 6.0 6.0 25 4.8 4.0 30 75 24 20 4.5 35 89 28 24 6.0 5 ns ns ns MHz 2.0 2.0 2.0 2.0 Fig.8 Fig.6 Fig.6 Fig.8 Fig.8 Fig.7 Fig.7 Fig.6 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 DC CHARACTERISTICS FOR 74HCT For the DC characteristics see "74HC/HCT/HCU/HCMOS Logic Family Specifications". Output capability: standard ICC category: MSI Note to HCT types The value of additional quiescent supply current (ICC) for a unit load of 1 is given in the family specifications. To determine ICC per input, multiply this value by the unit load coefficient shown in the table below. INPUT UNIT LOAD COEFFICIENT MR 1.00 CP 0.60 Dn 0.40 AC CHARACTERISTICS FOR 74HCT GND = 0 V; tr = tf = 6 ns; CL = 50 pF Tamb (C) TEST CONDITIONS 74HCT SYMBOL PARAMETER +25 min. -40 to +85 typ. max. min. max. -40 to +125 UNIT VCC (V) WAVEFORMS min. max. tPHL/ tPLH propagation delay CP to Qn, Qn 19 33 41 50 ns 4.5 Fig.6 tPHL propagation delay MR to Qn 22 38 48 57 ns 4.5 Fig.8 tPLH propagation delay MR to Qn 19 35 44 53 ns 4.5 Fig.8 tTHL/ tTLH output transition time 7 15 19 22 ns 4.5 Fig.6 tW clock pulse width HIGH or LOW 20 12 25 30 ns 4.5 Fig.6 tW master reset pulse width LOW 20 11 25 30 ns 4.5 Fig.8 trem removal time MR to CP 5 -10 5 5 ns 4.5 Fig.8 tsu set-up time Dn to CP 16 5 20 24 ns 4.5 Fig.7 th hold time CP to Dn 5 0 5 5 ns 4.5 Fig.7 fmax maximum clock pulse frequency 25 49 20 17 MHz 4.5 Fig.6 1998 Jul 08 6 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 AC WAVEFORMS (1) Fig.6 (1) The shaded areas indicate when the input is permitted to change for predictable output performance. HC : VM = 50%; VI = GND to VCC. HCT : VM = 1.3 V; VI = GND to 3 V. (1) Waveforms showing the clock (CP) to outputs (Qn, Qn) propagation delays, the clock pulse width, output transition times and the maximum clock pulse frequency. Fig.7 HC : VM = 50%; VI = GND to VCC. HCT : VM = 1.3 V; VI = GND to 3 V. Fig.8 Waveforms showing the master reset (MR) pulse width, the master reset to outputs (Qn, Qn) propagation delays and the master reset to clock (CP) removal time. 1998 Jul 08 HC : VM = 50%; VI = GND to VCC. HCT : VM = 1.3 V; VI = GND to 3 V. 7 Waveforms showing the data set-up and hold times for the data input (Dn). Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 PACKAGE OUTLINES DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 9 16 pin 1 index E 1 8 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.7 0.51 3.7 1.40 1.14 0.53 0.38 0.32 0.23 21.8 21.4 6.48 6.20 2.54 7.62 3.9 3.4 8.25 7.80 9.5 8.3 0.254 2.2 inches 0.19 0.020 0.15 0.055 0.045 0.021 0.015 0.013 0.009 0.86 0.84 0.26 0.24 0.10 0.30 0.15 0.13 0.32 0.31 0.37 0.33 0.01 0.087 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT38-1 050G09 MO-001AE 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 92-10-02 95-01-19 8 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE v M A Z 16 9 Q A2 A (A 3) A1 pin 1 index Lp 1 L 8 e 0 detail X w M bp 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.39 0.014 0.0075 0.38 0.16 0.15 0.050 0.039 0.016 0.028 0.020 0.01 0.01 0.004 0.028 0.012 inches 0.244 0.041 0.228 Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT109-1 076E07S MS-012AC 1998 Jul 08 EIAJ EUROPEAN PROJECTION ISSUE DATE 95-01-23 97-05-22 9 o 8 0o Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm D SOT338-1 E A X c y HE v M A Z 9 16 Q A2 A (A 3) A1 pin 1 index Lp L 8 1 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 2.0 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 7.9 7.6 1.25 1.03 0.63 0.9 0.7 0.2 0.13 0.1 1.00 0.55 8 0o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 1998 Jul 08 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 94-01-14 95-02-04 MO-150AC 10 o Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index Lp L 1 8 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.10 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1.0 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8 0o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 1998 Jul 08 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION ISSUE DATE 94-07-12 95-04-04 MO-153 11 o Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. Typical reflow temperatures range from 215 to 250 C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. WAVE SOLDERING This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (order code 9398 652 90011). Wave soldering can be used for all SO packages. Wave soldering is not recommended for SSOP and TSSOP packages, because of the likelihood of solder bridging due to closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices. DIP If wave soldering is used - and cannot be avoided for SSOP and TSSOP packages - the following conditions must be observed: SOLDERING BY DIPPING OR BY WAVE The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The longitudinal axis of the package footprint must be parallel to the solder flow and must incorporate solder thieves at the downstream end. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Even with these conditions: * Only consider wave soldering SSOP packages that have a body width of 4.4 mm, that is SSOP16 (SOT369-1) or SSOP20 (SOT266-1). * Do not consider wave soldering TSSOP packages with 48 leads or more, that is TSSOP48 (SOT362-1) and TSSOP56 (SOT364-1). REPAIRING SOLDERED JOINTS Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. SO, SSOP and TSSOP Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. REFLOW SOLDERING Reflow soldering techniques are suitable for all SO, SSOP and TSSOP packages. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. 1998 Jul 08 74HC/HCT175 12 Philips Semiconductors Product specification Quad D-type flip-flop with reset; positive-edge trigger 74HC/HCT175 REPAIRING SOLDERED JOINTS Fix the component by first soldering two diagonally- opposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1998 Jul 08 13 Philips Semiconductors - PIP - 74HC175;74HCT175; quad D-type flip-flop with reset; positive-edge trigger Submit Query Philips Semiconductors Home ProductBuy MySemiconductors ContactProduct Information catalogonline Products MultiMarket Semiconductors * Product Selector Catalog by * Function Catalog by * System * Cross-reference * Packages End of Life * information Distributors Go * Here! * Models * SoC solutions * as of 2003-04-22 74HC175;74HCT175;Information My.Semiconductors.COM. personal service from Use right mouse button to quad D-type flip-flop Your download datasheet Philips Semiconductors. register now ! Download datasheet with reset; positive- Please Stay informed edge trigger General description Features Buy online Parametrics Block diagram Products & packages Datasheet Email/translate Applications Support & tools Similar products General description top The 74HC/HCT175 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT175 have four edge-triggered, D-type flip-flops with individual D inputs and both Q and Q outputs. The common clock (CP) and master reset (MR) inputs load and reset (clear) all flip-flops simultaneously. The state of each D inputone set-up time before the LOW-to-HIGH clock transitionis transferred to the corresponding output (Qn ) of the flip-flop. All Qn outputs will be forced LOW independently of clock or data inputs by a LOW voltage level on the MR input. The device is useful for applications where both the true and complement outputs are required and the clock and master reset are common to all storage elements. Features top Four edge-triggered D flip-flops Output capability: standard ICC category: MSI Datasheet top Type number Title Publication release date 74HC175;74HCT175 quad D-type 7/8/1998 flip-flop with reset; positive-edge trigger Datasheet status Page count File size (kB) Datasheet Product specification 5 91 Download Download PDF File Additional datasheet info file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC175N.html (1 of 5) [Apr-29-2003 12:32:02 PM] Philips Semiconductors - PIP - 74HC175;74HCT175; quad D-type flip-flop with reset; positive-edge trigger To complete the device datasheet with package and family information, also download the following PDF files. The "Logic Package Information" document is required to determine in which package(s) this device is available. Document Description 1 Download HCT_FAMILY_SPECIFICATIONS PDF 2 Download File HCT_PACKAGE_INFO PDF 3 Download File HCT_PACKAGE_OUTLINES PDF File HC/T Family Specifications, The IC06 74HC/HCT/HCMOS Logic Family Specifications HC/T Package Info, The IC06 74HC/HCT/HCMOS Logic Package Information HC/T Package Outlines, The IC06 74HC/HCT/HCMOS Logic Package Outlines Parametrics top Type number Package Description Propagation Voltage No. Power Logic Output Delay(ns) of Dissipation Switching Drive Pins Considerations Levels Capability SOT109 (SO16) Quad DType FlipFlop with Reset; PositiveEdge Trigger 15 5 Volts 16 + Low Power or Battery Applications CMOS Low SOT338-1 (SSOP16) Quad DType FlipFlop with Reset; PositiveEdge Trigger 15 5 Volts 16 + Low Power or Battery Applications CMOS Low SOT38-1 (DIP16) Quad DType FlipFlop with Reset; PositiveEdge Trigger 15 5 Volts 16 + Low Power or Battery Applications CMOS Low Quad DType FlipFlop with SOT403-1 Reset; 74HC175PW (TSSOP16) PositiveEdge Trigger 15 5 Volts 16 + Low Power or Battery Applications CMOS Low 74HC175D 74HC175DB 74HC175N file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC175N.html (2 of 5) [Apr-29-2003 12:32:02 PM] Philips Semiconductors - PIP - 74HC175;74HCT175; quad D-type flip-flop with reset; positive-edge trigger SOT109 (SO16) Quad DType FlipFlop with Reset; PositiveEdge Trigger; TTL Enabled 15 5 Volts 16 + Low Power or Battery Applications TTL Low SOT338-1 (SSOP16) Quad DType FlipFlop with Reset; PositiveEdge Trigger; TTL Enabled 15 5 Volts 16 + Low Power or Battery Applications TTL Low SOT38-1 (DIP16) Quad DType FlipFlop with Reset; PositiveEdge Trigger; TTL Enabled 15 5 Volts 16 + Low Power or Battery Applications TTL Low Quad DType FlipFlop with Reset; SOT403-1 Positive74HCT175PW (TSSOP16) Edge Trigger; TTL Enabled 15 5 Volts 16 + Low Power or Battery Applications TTL Low 74HCT175D 74HCT175DB 74HCT175N Products, packages, availability and ordering top Type number North Ordering code Marking/Packing Package Device status Buy online Discretes American type (12NC) Download packing info number PDF File Standard Marking SOT109 74HC175D 74HC175D 9337 145 80652 * Bulk Pack, Full production order this (SO16) CECC product Standard Marking online SOT109 74HC175D-T 9337 145 80653 * Reel Pack, Full production order this (SO16) SMD, 13", CECC product Standard Marking SOT338-1 74HC175DB 74HC175DB 9351 873 90112 Full production online order this (SSOP16) * Bulk Pack product Standard Marking SOT338-1 74HC175DB9351 873 90118 * Reel Pack, Full production online order this (SSOP16) T SMD, 13" product online file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC175N.html (3 of 5) [Apr-29-2003 12:32:02 PM] - - Philips Semiconductors - PIP - 74HC175;74HCT175; quad D-type flip-flop with reset; positive-edge trigger 74HC175N 74HC175N Standard Marking SOT38-1 9336 694 40652 * Bulk Pack, (DIP16) CECC Full production order this product SOT403-1 online Standard Marking 74HC175PW 74HC175PW 9351 745 60112 (TSSOP16) Full production order this * Bulk Pack product Standard Marking SOT403-1 online 74HC175PW9351 745 60118 * Reel Pack, (TSSOP16) Full production order this T SMD, 13" product Standard Marking online SOT109 74HCT175D 74HCT175D 9337 150 60652 * Bulk Pack, Full production order this (SO16) CECC product Standard Marking online SOT109 74HCT175D9337 150 60653 * Reel Pack, Full production order this (SO16) T SMD, 13", CECC product Standard Marking SOT338-1 74HCT175DB 74HCT175DB 9351 885 90112 Full production online order this (SSOP16) * Bulk Pack product Standard Marking SOT338-1 74HCT175DB9351 885 90118 * Reel Pack, Full production online order this (SSOP16) T SMD, 13" product Standard Marking online SOT38-1 74HCT175N 74HCT175N 9336 700 70652 * Bulk Pack, Full production order this (DIP16) CECC product SOT403-1 online Standard Marking 74HCT175PW 74HCT175PW 9351 889 70112 (TSSOP16) Full production order this * Bulk Pack product Standard Marking SOT403-1 online 74HCT175PW9351 889 70118 * Reel Pack, (TSSOP16) Full production order this T SMD, 13" product online Products in the above table are all in production. Some variants are discontinued; click here for information on these variants. Similar products top 74HC175;74HCT175 links to the similar products page containing an overview of products that are similar in Products function similar or related to the type number(s) as listed on this page. The similar products page includes products from the same catalog tree(s), relevant selection guides and products from the same functional category. to 74HC175;74HCT175 Support & tools top HC/T Family Specifications, The IC06 74HC/HCT/HCMOS Logic Family Specifications(date 01-Mar-98) Download Download PDF HC/T User Guide(date 01-Nov-97) PDF File File file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC175N.html (4 of 5) [Apr-29-2003 12:32:02 PM] Philips Semiconductors - PIP - 74HC175;74HCT175; quad D-type flip-flop with reset; positive-edge trigger Email/translate this product information top Email this product information. Translate this product information page from English to: French Translate The English language is the official language used at the semiconductors.philips.com website and webpages. All translations on this website are created through the use of Google Language Tools and are provided for convenience purposes only. No rights can be derived from any translation on this website. About this Web Site | Copyright (c) 2003 Koninklijke Philips N.V. All rights reserved. | Privacy Policy | | Koninklijke Philips N.V. | Access to and use of this Web Site is subject to the following Terms of Use. | file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC175N.html (5 of 5) [Apr-29-2003 12:32:02 PM]