01/2012
AWT6624
Multi-Mode HELP4TM UMTS1700
(Band 4+9+3+10) WCDMA/CDMA Linear PAM
Data Sheet - Rev 2.8
M45 Package
10 Pin 3 mm x 3 mm x 1 mm
Surface Mount Module
Figure 1: Block Diagram
FEATURES
• Mixed-Mode(HSPA,EV-DO)Compliant
• 4thGenerationHELPTM technology
• HighEfciency(R99waveform):
39 % @ POUT=+28.3dBm
36% @ POUT=+17dBm
22 % @ POUT=+13.5dBm
26% @ POUT=+8dBm
13 % @ POUT=+3.5dBm
• LowQuiescentCurrent:2mA
• LowLeakageCurrentinShutdownMode:
<5 µA
• InternalVoltageRegulator
• Integrated“daisychainable”directionalcoupler
withCPLIN and CPLOUTport.
• Optimizedfora50ΩSystem
• 1.8VControlLogic
• RoHSCompliantPackage,260oC MSL-3
APPLICATIONS
• Band4(alsoBands3,9and10)WCDMA/HSPA
WirelessDevices
• AWS/KPCSCDMA/EV-DOWirelessDevices
PRODUCT DESCRIPTION
The AWT6624 HELP4TMPAisa4thgenerationHELPTM
productforWCDMAdevicesoperatinginUMTS1700
(Band 4 + 9) and for CDMA devices operating in
AWS/KPCSband.ThisPAincorporatesANADIGICS’
HELP4TMtechnologytodeliverexceptionalefciency
atlowpowerlevelsandlowquiescentcurrentwithout
theneedforexternalvoltageregulatorsorconverters.
ThedeviceismanufacturedusingadvancedInGaP-
PlusTM HBT technology offering state-of-the-art
reliability, temperature stability, and ruggedness.
Threeselectablebiasmodesthatoptimizeefciency
for different output power levels and a shutdown
mode with low leakage current increase handset
talkandstandbytime.A“daisychainable”directional
couplerisintegratedinthemodule,thuseliminating
theneedofanexternalcoupler.Theself-contained
3 mm x 3 mm x 1 mm surface mount package
incorporatesmatchingnetworksoptimizedforoutput
power, efciency, and linearity in a 50 Ω system.
1
2
3
4
5
10
9
8
7
6
VBATT
RFIN
VMODE2
VMODE1
VEN CPLOU
T
GND
CPLIN
RFOUT
VCC
Bias Control
Voltage Regulation
CPL
GND at Slug (pad)
AWT6624
2Data Sheet - Rev 2.8
01/2012
AWT6624
Figure 2: Pinout (X-ray Top View)
Table 1: Pin Description
V
BATT
RF
IN
V
MODE2
V
MODE1
V
EN
1
2
3
4
56
7
8
9
10
CPL
OUT
GND
CPL
IN
RF
OUT
V
CC
1
2
3
4
56
7
8
9
10
PIN NAME DESCRIPTION
1V
BATT
BatteryVoltage
2RF
IN
RFInput
3V
MODE2
ModeControlVoltage2
4V
MODE1
ModeControlVoltage1
5V
EN
PAEnableVoltage
6CPL
OUT
CouplerOutput
7GND Ground
8CPL
IN
CouplerInput
9RF
OUT
RFOutput
10 V
CC
SupplyVoltage
3Data Sheet - Rev 2.8
01/2012
AWT6624
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings
Stresses in excess of the absolute ratings may cause permanent damage.
Functional operation is not implied under these conditions. Exposure
to absolute ratings for extended periods of time may adversely affect
reliability.
Table 3: Operating Ranges
The device may be operated safely over these conditions; however, parametric performance is guaranteed only
overtheconditionsdenedintheelectricalspecications.
Notes:
(1) For Operation at 3.2 V, POUT is derated 0.5 dB.
PARAMETER MIN MAX UNIT
SupplyVoltage(V
CC
) 0 +5 V
BatteryVoltage(V
BATT
) 0 +6 V
ControlVoltages(V
MODE1
,V
MODE2
,V
EN
) 0 +3.5 V
RFInputPower(P
IN
) - +10 dBm
StorageTemperature(T
STG
)-40 +150 °C
PARAMETER MIN TYP MAX UNIT COMMENTS
OperatingFrequency(f) 1710 -1785 MHz
SupplyVoltage(V
CC
)+3.2 +3.4 +4.2 VP
OUT
<+28.3dBm
EnableVoltage(V
EN
)+1.35
0
+1.8
-
+3.1
+0.5 VPA "on"
PA"shutdown"
ModeControlVoltage(V
MODE1
,V
MODE2
)+1.35
0
+1.8
-
+3.1
+0.5 VLowBiasMode
HighBiasMode
WCDMAOutputPower(UMTS)
R99,HPM
HSPA(MPR=0),HPM
R99,MPM
HSPA(MPR=0),MPM
R99,LPM
HSPA(MPR=0),LPM
27.8
(1)
26.8
(1)
17.0
16.0
-
-
28.3
27.3
17.0
16.0
8.0
7.0
-
-
-
-
-
-
dBm 3GPPTS34.121-1,Rel
8TableC.11.1.3,
SUBTEST 1
CDMAOutputPower
CDMA2000,HPM
CDMA2000,MPM
CDMA,LPM
27.2
(1)
-
7.5
(1)
27.7
16.0
8.0
-
-
-
dBm CDMA2000,
RC-1
CaseTemperature(T
C
)-30 -+90 °C
4Data Sheet - Rev 2.8
01/2012
AWT6624
Table4:ElectricalSpecications-WCDMAOperation(R99waveform)
(TC = +25 °C, VCC = +3.4 V, VBATT = +3.4 V, VEN = +1.8 V, 50 Ω system)
Notes:
(1) ACLR and Efciency measured at 1747.5 MHz.
PARAMETER
MIN TYP MAX UNIT
COMMENTS
POUT VMODE1 VMODE2
Gain
25
17
7.5
27
20
10
30
23
12.5
dB
+28.3dBm
+17dBm
+8dBm
0V
1.8V
1.8V
0V
0V
1.8V
ACLR1at5MHzoffset
(1)
-
-
-
-41
-42
-40
-37
-37
-37
dBc
+28.3dBm
+17.dBm
+8dBm
0V
1.8V
1.8V
0V
0V
1.8V
ACLR2at10MHzoffset
-
-
-
-55
-54
-58
-48
-48
-48
dBc
+28.3dBm
+17dBm
+8dBm
0V
1.8V
1.8V
0V
0V
1.8V
Power-AddedEfficiency
(1)
36
32
-
23
-
39
36
22
26
13
-
-
-
-
-
%
+28.3dBm
+17dBm
+13.5dBm
+8dBm
+3.5dBm
0V
1.8V
1.8V
1.8V
1.8V
0V
0V
0V
1.8V
1.8V
QuiescentCurrent(Icq)
LowBiasMode - 2 3.5 mA through
VCCpin 1.8V 1.8V
Mode Control Current -0.08 0.15 mA throughVMODEpins,VMODE1,2 = +1.8V
EnableCurrent -0.04 0.1 mA throughVENpin
BATT Current -0.8 1.5 mA throughVBATTpin,VMODE1,2=+1.8V
LeakageCurrent -<5 10 µA VBATT=+4.2V,VCC=+4.2V,
VEN=0V,VMODE1,2=0V
NoisePower
-
-
-
-
-
-140
-135
-135
-132
-148
-137
-132
-132
-
-
dBm/Hz
2110MHzto2155MHz(Band4)
1805MHzto1880MHz(Band3)
1844.9MHzto1879.9MHz(Band9)
GPSBand
ISM Band
Harmonics
2fo
3fo,4fo
-
-
-44
-50
-35
-42 dBc POUT <+28.3dBm
CouplingFactor -20 -dB
Directivity -20 -dB
DaisyChainInsertionLoss -<0.25 -dB
SpuriousOutputLevel
(allspuriousoutputs) - - -70 dBc
POUT <+28.3dBm
In-bandloadVSWR<5:1
Out-of-bandloadVSWR<10:1
Appliesoveralloperatingconditions
Loadmismatchstresswithno
permanentdegradationorfailure 8:1 - - VSWR Appliesoverfulloperatingrange
5Data Sheet - Rev 2.8
01/2012
AWT6624
Table5:ElectricalSpecications-CDMAOperation(CDMA2000RCI)
(TC = +25 °C, VBATT = VCC = +3.4 V, VENABLE = +1.8 V, 50 Ω system)
Notes:
(1) ACLR and Efciency measured at 1747.5 MHz.
2. POUT < +27.7 dBm, In-Band VSWR < 5:1, Out-Of-Band VSWR < 10:1. Applies to all operating conditions.
PARAMETER MIN TYP MAX UNIT
COMMENTS
POUT VMODE1 VMODE2
Gain
25
17
7.5
27
20
10
30
23
12.5
dB
POUT=+27.7dBm
POUT=+16.0dBm
POUT=+8.0dBm
0V
1.8V
1.8V
0V
0V
1.8V
AdjacentChannelPower
at +1.25MHzoffset
PrimaryChannelBW=1.23MHz
AdjacentChannelBW=30kHz
-
-
-
-51
-55
-57
-46.5
-46.5
-46.5
dBc
POUT=+27.7dBm
POUT=+16.0dBm
POUT=+8.0dBm
0V
1.8V
1.8V
0V
0V
1.8V
AdjacentChannelPower
at +1.98MHzoffset
PrimaryChannel=1.23MHz
AdjacentChannel=30kHz
-
-
-
-56
-58
-60
-53
-53
-54
dBc
POUT=+27.7dBm
POUT=+16.0dBm
POUT=+8.0dBm
0V
1.8V
1.8V
0V
0V
1.8V
Power-AddedEfficiency
33
28
20
37
33
25
-
-
-
%
POUT=+27.7dBm
POUT=+16.0dBm
POUT=+8.0dBm
0V
1.8V
1.8V
0V
0V
1.8V
SpuriousOutputLevel
(allspuriousoutputs) - - -70 dBc See Note 2
Loadmismatchstresswithno
permanentdegradationorfailure 8:1 - - VSWR Appliesoverfulloperatingrange
6Data Sheet - Rev 2.8
01/2012
AWT6624
APPLICATION INFORMATION
To ensure proper performance, refer to all related
Application Notes on theANADIGICS web site:
http://www.anadigics.com
Shutdown Mode
Thepowerampliermaybeplacedinashutdownmode
byapplyinglogiclowlevels(seeOperatingRanges
table)totheVEN,VMODE1 andVMODE2voltages.
Bias Modes
The power amplier may be placed in either Low,
Medium or High Bias modes by applying the
appropriatelogiclevel(seeOperatingRangestable)
Table 6: Bias Control
totheVMODEpins.TheBiasControltablebelowlists
the recommended modes of operation for various
applications.
Threeoperatingmodesarerecommendedtooptimize
currentconsumption.HighBias/HighPoweroperating
modeisforPOUTlevels>16dBm.At~17dBm-7dBm,
thePAcouldbeswitchedtoMediumPowerMode.For
POUTlevels<~8dBm,thePAcouldbeswitchedtoLow
PowerModeforextremelylowcurrentconsumption.
Figure 3: Evaluation Board Schematic
C4
2.2 µF ceramic
RFIN
1
6
7
10
8
5
4
3
VBATT
VMODE1
RFOUTRFIN
GND
VCC
VEN CPLOUT
VCC
C1
0.1µF
VBATT
VMODE1
VEN
CPLIN
VMODE2
29
VMODE2
C5
2.2 µF
C2
0.1µF
GND at slug
CPLIN C6
33 pF
CPLOUT
RFOUT
C3
33 pF
APPLICATION
P
OUT
LEVELS
(Rel.99)
BIAS
MODE V
EN
V
MODE1
V
MODE2
V
CC
V
B AT T
Lowpower
(LowBiasMode) <+8dBm Low +1.8V +1.8V +1.8V 3.2-4.2V >3.2V
Medpower
(MediumBiasMode)
>7dBm
<+17dBm Low +1.8V +1.8V 0V 3.2-4.2V >3.2V
Highpower
(HighBiasMode) >+16dBm High +1.8V 0V 0V 3.2-4.2V >3.2V
Shutdown -Shutdown 0V 0V 0V 3.2-4.2V >3.2V
7Data Sheet - Rev 2.8
01/2012
AWT6624
PERFORMANCE DATA PLOTS:
(R99waveformat1747.5MHzand50V)
0
5
10
15
20
25
0 5 10 15 20 25 30
Gain (dB)
Pout (dBm)
Figure 4: WCDMA Gain (dB) over Temperature
(Vbatt=VCC=3.4V)
-30C3.4Vcc
25C3.4Vcc
90C3.4Vcc
Figure 4: WCDMA Gain (dB) over Temperature
(Vbatt = VCC = 3.4 V)
0
5
10
15
20
25
30
0 5 10 15 20 25 30
Gain (dB)
Pout (dBm)
Figure 5: WCDMA Gain (dB) over Voltage
(Tc=25C)
25C3.2Vcc
25C3.4Vcc
25C4.2Vcc
Figure 5: WCDMA Gain (dB) over Voltage
(TC = 25 8C)
0
10
20
30
40
50
60
0 5 10 15 20 25 30
Efficiency (%)
Pout (dBm)
Figure 6: WCDMA PAE (%) over Temperature
(Vbatt=VCC=3.4V)
-30 3.4cc
25C3.4Vcc
90C3.4Vcc
Figure 6: WCDMA PAE (%) over Temperature
(Vbatt = VCC = 3.4 V)
0
10
20
30
40
50
60
0 5 10 15 20 25 30
Efficiency
Pout (dBm)
Figure7:WCDMAPAE(%)overVoltage
(Tc=25C)
25C3.2Vcc
25C3.4Vcc
25C4.2Vcc
Figure7:WCDMAPAE(%)overVoltage
(TC = 25 8C)
-55
-50
-45
-40
-35
-30
-25
-20
0 5 10 15 20 25 30
ACLR1(5MHzdBc)
Pout (dBm)
Figure 8: WCDMA ACRL1 (dBc) over Temperature
(Vbatt=VCC=3.4V)
-30C3.4Vcc
25C3.4Vcc
90C3.4Vcc
Figure 8: WCDMA ACLR1 (dBc) over Temperature
(Vbatt = VCC = 3.4 V)
-55
-50
-45
-40
-35
-30
-25
-20
0 5 10 15 20 25 30
ACLR1(5MHzdBc)
Pout (dBm)
Figure9:WCDMAACLR1(dBc)overVoltage
(Tc=25C)
25C3.2Vcc
25C3.4Vcc
25C4.2Vcc
Figure9:WCDMAACLR1(dBc)overVoltage
(TC = 25 8C)
8Data Sheet - Rev 2.8
01/2012
AWT6624
Figure 10: M45 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module
Figure11:BrandingSpecication-M45Package
PACKAGE OUTLINE
6624R
LLLLNN
YYWWCC
Pin 1 Identifier
Country Code(CC)
Part Number
Date Code
YY=Year; WW=Work Week
Lot Number
9Data Sheet - Rev 2.8
01/2012
AWT6624
PCB AND STENCIL DESIGN GUIDELINE
Figure 12: Recommended PCB Layout Information
10 Data Sheet - Rev 2.8
01/2012
AWT6624
COMPONENT PACKAGING
Figure 13: Carrier Tape
Pin 1
Figure 14: Reel
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product
in any such application without written consent is prohibited.
IMPORTANT NOTICE
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice.
The product specications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to
change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed
to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers
to verify that the information they are using is current before placing orders.
Data Sheet - Rev 2.8
01/2012
11
AWT6624
ORDERING INFORMATION
ORDER NUMBER TEMPERATURE
RANGE
PACKAGE
DESCRIPTION COMPONENT PACKAGING
AWT6624RM45Q7 -30 oC to +90 oC
RoHS-Compliant10Pin
3mmx3mmx1mm
SurfaceMountModule
TapeandReel,2500piecesper
Reel
AWT6624RM45P9 -30 oC to +90 oC
RoHSCompliant10Pin
3mmx3mmx1mm
SurfaceMountModule
PartialTapeandReel