This section presents complete electrical specifications for Teccor's SIDACtor solid state overvoltage protection devices. DO-214AA Package Symbolization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 DO-214AA SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 MicroCapacitance (MC) SC SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 MicroCapacitance (MC) SA SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 High Surge Current (D-rated) SIDACtor Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Compak Two-chip SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Ethernet/10BaseT/100BaseT Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 TO-92 SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 MicroCapacitance (MC) SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Modified MS-013 (Six-pin Surface Mount) Balanced Three-chip SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Multiport SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Multiport Balanced SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 Modified TO-220 SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26 Two-chip SIDACtor Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 Two-chip MicroCapacitance (MC) SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30 Balanced Three-chip SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32 Balanced Three-chip MicroCapacitance (MC) SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . 2-34 LCAS LCAS Asymmetrical Multiport Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36 LCAS Asymmetrical Discrete Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38 SIP Hybrid Overvoltage and Overcurrent Protector Four-Port Balanced Three-chip Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40 Four-Port Longitudinal Two-chip Protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42 Four-Port Metallic Line Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 SLICs Fixed Voltage SLIC Protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46 Twin SLIC Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48 Multiport SLIC Protector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-50 Battrax Battrax SLIC Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52 Battrax Dual Negative SLIC Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-54 Battrax Dual Positive/Negative SLIC Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56 Battrax Quad Negative SLIC Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-58 CATVs CATV and HFC SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60 High Surge Current SIDACtor Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-62 CATV Line Amplifiers/Power Inserters SIDACtor Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-64 TeleLink Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66 Acronyms: CATV HFC LCAS SIP SLIC (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Community Antenna TV Hybrid Fiber Coax Line Circuit Access Switch Single In-line Package Subscriber Line Interface Circuit 2-1 http://www.teccor.com +1 972-580-7777 Data Sheets 2 Data Sheets DO-214AA Package Symbolization DO-214AA Package Symbolization Part Number Symbolized Catalog Part Number Symbolized Catalog Symbolized P0080SA P-8A P1100SB P11B P2300SD P0080SB P-8B P1100SC P11C P2300SC MC P0080SC P-8C P1100SD P0080SD P-8D P1100SC MC P0080SC MC P-8CM P1101CA2 P23D P23CM P11D P2500SA P11CM P2500SB P25A P25B P02A P2500SC P25C P0300SA P03A P1101SA P01A P2500SD P0300SB P03B P1101SC P01C P2500SC MC P0300SC P03C P1200SA P12A P2600SA P0300SD P03D P1200SB P12B P2600SB P26B P03CM P1200SC P12C P2600SC P26C P0640SA P06A P1200SD P0640SB P06B P1200SC MC P0640SC P06C P1300SA P13A P3002CB P0640SD P06D P1300SB P13B P3002SB P30B P06CM P1300SC P13C P3100SA P31A P0641CA2 P62A P1300SD P0641SA P61A P1300SC MC P0641SC P61C P0720SA P07A P0300SC MC P0640SC MC P12D P12CM P25D P25CM P26A P2600SD P26D P2600SC MC P26CM P30B P13D P3100SB P31B P13CM P3100SC P31C P1500SA P15A P3100SD P1500SB P15B P3100SC MC P31D P31CM P0720SB P07B P1500SC P15C P3500SA P35A P0720SC P07C P1500SD P15D P3500SB P35B P35C P0720SD P0720SC MC P0721CA2 P15CM P3500SC P07CM P07D P1800SA P1500SC MC P18A P3500SD P72A P1800SB P18B P3500SC MC P35D P35CM P0721SA P71A P1800SC P18C P6002CB P60B P0721SC P71C P1800SD P18D B1100CA B10A P0900SA P09A P1800SC MC P18CM B1100CC B10C P0900SB P09B P2000SA P20A B1160CA B16A P0900SC P09C P2000SB P20B B1160CC B16C P0900SD P0900SC MC P09D P2000SC P20C B1200CA B12A P09CM P2000SD P20D B1200CC B20C P20CM B2050CA B20A P23A B2050CC B20C P0901CA2 P92A P2000SC MC P0901SA P91A P2300SA P0901SC P91C P2300SB P23B P1100SA P11A P2300SC P23C Note: Date code is located below the symbolized part number. (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide 2-3 http://www.teccor.com +1 972-580-7777 Data Sheets Part Number Catalog SIDACtor Device SIDACtor Device DO-214AA SIDACtor solid state protection devices protect telecommunications equipment such as modems, line cards, fax machines, and other CPE. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0080S_ 6 25 4 5 800 2.2 50 100 P0300S_ 25 40 4 5 800 2.2 50 110 P0640S_ 58 77 4 5 800 2.2 150 50 P0720S_ 65 88 4 5 800 2.2 150 50 P0900S_ 75 98 4 5 800 2.2 150 50 P1100S_ 90 130 4 5 800 2.2 150 40 P1300S_ 120 160 4 5 800 2.2 150 40 P1500S_ 140 180 4 5 800 2.2 150 40 P1800S_ 170 220 4 5 800 2.2 150 30 P2300S_ 190 260 4 5 800 2.2 150 30 P2600S_ 220 300 4 5 800 2.2 150 30 P3100S_ 275 350 4 5 800 2.2 150 30 P3500S_ 320 400 4 5 800 2.2 150 30 * For individual "SA", "SB", and "SC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for "SA" and "SB" product. "SC" capacitance is approximately 2x the listed value. The off-state capacitance of the P0080SB is equal to the "SC" device. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2-4 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide SIDACtor Device Package Symbol Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W RqJA Parameter Thermal Resistance: Junction to Ambient IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2-5 http://www.teccor.com +1 972-580-7777 Data Sheets Thermal Considerations MicroCapacitance (MC) SC SIDACtor Device MicroCapacitance (MC) SC SIDACtor Device The DO-214AA SC MC SIDACtor series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values for the MicroCapacitance device are 40% lower than a standard SC part. This MC SIDACtor series is used to enable equipment to meet various regulatory requirements including GR 1089, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Contact factory regarding ITU K.20, K.21, and K.45. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF 55 P0080SC MC ** 6 25 4 5 800 2.2 50 P0300SC MC ** 25 40 4 5 800 2.2 50 35 P0640SC MC 58 77 4 5 800 2.2 150 60 P0720SC MC 65 88 4 5 800 2.2 150 60 P0900SC MC 75 98 4 5 800 2.2 150 60 P1100SC MC 90 130 4 5 800 2.2 150 50 P1300SC MC 120 160 4 5 800 2.2 150 50 P1500SC MC 140 180 4 5 800 2.2 150 50 P1800SC MC 170 220 4 5 800 2.2 150 40 P2300SC MC 190 260 4 5 800 2.2 150 40 P2600SC MC 220 300 4 5 800 2.2 150 40 P3100SC MC 275 350 4 5 800 2.2 150 40 P3500SC MC 320 400 4 5 800 2.2 150 40 * For surge ratings, see table below. ** Contact factory for release date. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 2-6 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide MicroCapacitance (MC) SC SIDACtor Device Thermal Considerations Symbol TJ Operating Junction Temperature Range Parameter -40 to +150 Value C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient RqJA Unit IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2-7 http://www.teccor.com +1 972-580-7777 Data Sheets Package DO-214AA MicroCapacitance (MC) SA SIDACtor Device MicroCapacitance (MC) SA SIDACtor Device The DO-214AA SA MC SIDACtor series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values for the MicroCapacitance device are 40% lower than a standard SA part. This MC SIDACtor series is used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/ EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0080SA MC 6 25 4 5 800 2.2 50 45 P0300SA MC 25 40 4 5 800 2.2 50 25 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 http://www.teccor.com +1 972-580-7777 2-8 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide MicroCapacitance (MC) SA SIDACtor Device Thermal Considerations Symbol TJ Operating Junction Temperature Range Parameter -40 to +150 Value C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient RqJA Unit IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2-9 http://www.teccor.com +1 972-580-7777 Data Sheets Package DO-214AA High Surge Current (D-rated) SIDACtor Device High Surge Current (D-rated) SIDACtor Device DO-214AA SIDACtor solid state protection devices with a D surge rating protect telecommunications equipment such as modems, line cards, fax machines, and other CPE. These SIDACtor devices withstand simultaneous surges incurred in GR 1089 lightning tests. (See "First Level Lightning Surge Test" on page 4-5.) Surge ratings are twice that of a device with a C surge rating. This allows a discrete surface mount version of Teccor's patented "Y" configuration. (US Patent 4,905,119) SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0080SD ** 6 25 4 5 800 2.2 50 200 P0300SD ** 25 40 4 5 800 2.2 50 220 P0640SD ** 58 77 4 5 800 2.2 50 100 P0720SD ** 65 88 4 5 800 2.2 50 100 P0900SD ** 75 98 4 5 800 2.2 50 100 P1100SD 90 130 4 5 800 2.2 50 80 P1300SD 120 160 4 5 800 2.2 50 80 P1500SD 140 180 4 5 800 2.2 50 80 P1800SD 170 220 4 5 800 2.2 50 60 P2300SD 190 260 4 5 800 2.2 50 60 P2600SD 220 300 4 5 800 2.2 50 60 P3100SD 275 350 4 5 800 2.2 50 60 P3500SD 320 400 4 5 800 2.2 50 60 * For surge ratings, see table below. ** Contact factory for release date. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s D 1000 800 400 300 200 50 1000 http://www.teccor.com +1 972-580-7777 2 - 10 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide High Surge Current (D-rated) SIDACtor Device Thermal Considerations Package Symbol Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 11 http://www.teccor.com +1 972-580-7777 Compak Two-chip SIDACtor Device Compak Two-chip SIDACtor Device The modified DO-214AA SIDACtor device provides low-cost, longitudinal protection. 1 (T) 2 (G) 3 SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). (R) Electrical Parameters Part Number VDRM Volts VS Volts VDRM Volts Pins1-2, 2-3 VS Volts Pins 1-3 CO pF VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 1-3 P3002CA 140 180 280 360 4 5 800 1 120 15 P6002CA 275 350 550 700 4 5 800 1 120 15 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-3 at 1 MHz with a 2 V bias. * UL 60950 creepage requirements must be considered. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 http://www.teccor.com +1 972-580-7777 2 - 12 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Compak Two-chip SIDACtor Device Thermal Considerations Package Symbol Value Unit Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 85 C/W Pin 3 RqJA Parameter Thermal Resistance: Junction to Ambient Pin 1 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 13 http://www.teccor.com +1 972-580-7777 Data Sheets Pin 2 Ethernet/10BaseT/100BaseT Protector Ethernet/10BaseT/100BaseT Protector The DO-214AA SIDACtor Ethernet protection series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values are 40% lower than standard devices. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0642S_ 58 77 4 5 800 2.2 150 25 P0722S_ 65 88 4 5 800 2.2 150 25 P0902S_ 75 98 4 5 800 2.2 150 25 P1102S_ 90 130 4 5 800 2.2 150 20 P3002S_ 280 360 4 5 800 2.2 150 15 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 B** 250 250 150 100 80 30 500 ** Contact factory for release date of B-rated devices. http://www.teccor.com +1 972-580-7777 2 - 14 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Ethernet/10BaseT/100BaseT Protector Package Symbol Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W RqJA Parameter Thermal Resistance: Junction to Ambient IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 15 http://www.teccor.com +1 972-580-7777 Data Sheets Thermal Considerations SIDACtor Device SIDACtor Device TO-92 SIDACtor solid state protection devices protect telecommunications equipment such as modems, line cards, fax machines, and other CPE. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68) . Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0080E_ 6 25 4 5 800 2.2 50 100 P0300E_ 25 40 4 5 800 2.2 50 110 P0640E_ 58 77 4 5 800 2.2 150 50 P0720E_ 65 88 4 5 800 2.2 150 50 P0900E_ 75 98 4 5 800 2.2 150 50 P1100E_ 90 130 4 5 800 2.2 150 40 P1300E_ 120 160 4 5 800 2.2 150 40 P1500E_ 140 180 4 5 800 2.2 150 40 P1800E_ 170 220 4 5 800 2.2 150 30 P2300E_ 190 260 4 5 800 2.2 150 30 P2600E_ 220 300 4 5 800 2.2 150 30 P3100E_ 275 350 4 5 800 2.2 150 30 P3500E_ 320 400 4 5 800 2.2 150 30 * For individual "EA", "EB", and "EC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for "EA" and "EB" product. "EC" capacitance is approximately 2x the listed value. The off-state capacitance of the P0080EB is equal to the "EC" device. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 16 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide SIDACtor Device Thermal Considerations Package Symbol TO-92 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 17 http://www.teccor.com +1 972-580-7777 MicroCapacitance (MC) SIDACtor Device MicroCapacitance (MC) SIDACtor Device The TO-92 MC SIDACtor series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values for MC devices are 40% lower than a standard EC part. This MC SIDACtor series is used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/ EIA-IS-968 (formerly known as FCC Part 68) without the need of series resistors. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0640EC MC 58 77 4 5 800 2.2 150 60 P1500EC MC 140 180 4 5 800 2.2 150 50 P2600EC MC 220 300 4 5 800 2.2 150 40 P3100EC MC 275 350 4 5 800 2.2 150 40 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 18 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide MicroCapacitance (MC) SIDACtor Device Thermal Considerations Package Symbol TO-92 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 19 http://www.teccor.com +1 972-580-7777 Balanced Three-chip SIDACtor Device Balanced Three-chip SIDACtor Device 1 6 2 5 3 4 This balanced protector is a surface mount alternative to the modified TO-220 package. Based on a six-pin surface mount SOIC package, it uses Teccor's patented "Y" (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VDRM Volts Pins 1-3, 1-4 VS Volts Pins 3-4 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P1553U_ 130 180 130 180 8 5 800 2.2 150 40 P1803U_ 150 210 150 210 8 5 800 2.2 150 40 P2103U_ 170 250 170 250 8 5 800 2.2 150 40 P2353U_ 200 270 200 270 8 5 800 2.2 150 40 P2703U_ 230 300 230 300 8 5 800 2.2 150 30 P3203U_ 270 350 270 350 8 5 800 2.2 150 30 P3403U_ 300 400 300 400 8 5 800 2.2 150 30 P5103U_ 420 600 420 600 8 5 800 2.2 150 30 A2106U_ ** 170 250 50 80 8 5 800 2.2 120 40 A5030U_ ** 400 550 270 350 8 5 800 2.2 150 30 * For individual "UA", "UB", and "UC" surge ratings, see table below. ** Asymmetrical General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-3 and 1-4 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 2x higher. * Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 20 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Balanced Three-chip SIDACtor Device Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 RqJA 4 Parameter Thermal Resistance: Junction to Ambient 1 3 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 21 http://www.teccor.com +1 972-580-7777 Data Sheets 2 Multiport SIDACtor Device Multiport SIDACtor Device 1 (R1) 6 (T2) 2 (G1) 5 (G2) 3 (T1) 4 (R2) The multiport line protector is an integrated multichip solution for protecting multiple twisted pair from overvoltage conditions. Based on a six-pin surface mount SOIC package, it is equivalent to four discrete DO-214AA or two TO-220 packages. Available in surge current ratings up to 500 A, the multiport line protector is ideal for densely populated, high-speed line cards that cannot afford PCB inefficiencies or the use of series power resistors. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts Pins 1-2, 3-2, 4-5, 6-5 VDRM Volts VS Volts VT Volts Pins 1-3, 4-6 IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0084U_ 6 25 12 50 4 5 800 2.2 50 100 P0304U_ 25 40 50 80 4 5 800 2.2 50 110 P0644U_ 58 77 116 154 4 5 800 2.2 150 50 P0724U_ 65 88 130 176 4 5 800 2.2 150 50 P0904U_ 75 98 150 196 4 5 800 2.2 150 50 P1104U_ 90 130 180 260 4 5 800 2.2 150 40 P1304U_ 120 160 240 320 4 5 800 2.2 150 40 P1504U_ 140 180 280 360 4 5 800 2.2 150 40 P1804U_ 170 220 340 440 4 5 800 2.2 150 30 P2304U_ 190 260 380 520 4 5 800 2.2 150 30 P2604U_ 220 300 440 600 4 5 800 2.2 150 30 P3104U_ 275 350 550 700 4 5 800 2.2 150 30 P3504U_ 320 400 640 800 4 5 800 2.2 150 30 * For individual "UA", "UB", and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM, and VS is measured at 100 V/s. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 2x higher. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 22 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Multiport SIDACtor Device Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 4 RqJA Parameter Thermal Resistance: Junction to Ambient 1 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 23 http://www.teccor.com +1 972-580-7777 Data Sheets 3 Multiport Balanced SIDACtor Device Multiport Balanced SIDACtor Device 1 6 2 5 3 4 This multiport balanced protector is a surface mount alternative to the modified TO-220 package. It is based on a six-pin surface mount SOIC package and uses Teccor's patented "Y" (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters -- Symmetrical Part Number * VDRM Volts VS Volts Pins 1-2, 2-3, 1-3 VDRM Volt VS Volts Pins 4-5, 5-6, 4-6 CO pF VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 3-2, 6-5, 1-2, 4-5 P1556U_ 130 180 130 180 8 5 800 2.2 150 50 P1806U_ 150 210 150 210 8 5 800 2.2 150 50 P2106U_ 170 250 170 250 8 5 800 2.2 150 40 P2356U_ 200 270 200 270 8 5 800 2.2 150 40 P2706U_ 230 300 230 300 8 5 800 2.2 150 40 P3206U_ 270 350 270 350 8 5 800 2.2 150 40 P3406U_ 300 400 300 400 8 5 800 2.2 150 40 P5106U_ 420 600 420 600 8 5 800 2.2 150 40 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF Electrical Parameters -- Asymmetrical Part Number * VDRM Volts VS Volts Pins 1-2, 2-3 VDRM Volt VS Volts Pins 4-6, 1-3 A2106U_6 170 250 50 80 3.5 5 800 2.2 120 40 A5030U_6 400 550 270 350 3.5 5 800 2.2 150 30 * For individual "UA", "UB", and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 10 pF higher. * Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 24 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Multiport Balanced SIDACtor Device Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 RqJA 4 Parameter Thermal Resistance: Junction to Ambient 1 2 Data Sheets 3 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 25 http://www.teccor.com +1 972-580-7777 SIDACtor Device SIDACtor Device The modified TO-220 Type 61 SIDACtor solid state protection device can be used in telecommunication protection applications that do not reference earth ground. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P2000AA61 180 220 4 5 800 2.2 150 30 P2200AA61 200 240 4 5 800 2.2 150 30 P2400AA61 220 260 4 5 800 2.2 150 30 P2500AA61 240 290 4 5 800 2.2 150 30 P3000AA61 270 330 4 5 800 2.2 150 30 P3300AA61 300 360 4 5 800 2.2 150 30 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings Series IPP 0.2x310 s Amps IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 5x320 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 20 150 150 90 50 75 45 20 500 http://www.teccor.com +1 972-580-7777 2 - 26 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Type 61 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH I DRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 27 http://www.teccor.com +1 972-580-7777 Two-chip SIDACtor Device Two-chip SIDACtor Device The two-chip modified TO-220 SIDACtor solid state device protects telecommunication equipment in applications that reference Tip and Ring to earth ground but do not require balanced protection. 1 (T) 2 (G) 3 (R) SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters VDRM Volts Part Number * VS Volts VDRM Volts Pins 1-2, 3-2 VS Volts Pins 1-3 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF 110 P0602A_ 25 40 50 80 4 5 800 2.2 50 P1402A_ 58 77 116 154 4 5 800 2.2 150 50 P1602A_ 65 95 130 190 4 5 800 2.2 150 50 P2202A_ 90 130 180 260 4 5 800 2.2 150 40 P2702A_ 120 160 240 320 4 5 800 2.2 150 40 P3002A_ 140 180 280 360 4 5 800 2.2 150 40 P3602A_ 170 220 340 440 4 5 800 2.2 150 40 P4202A_ 190 250 380 500 4 5 800 2.2 150 30 P4802A_ 220 300 440 600 4 5 800 2.2 150 30 P6002A_ 275 350 550 700 4 5 800 2.2 150 30 * For individual "AA", "AB", and "AC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "AA" and "AB" product. "AC" capacitance is approximately 2x the listed value. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 28 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Two-chip SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W PIN 1 Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter PIN 3 PIN 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 29 http://www.teccor.com +1 972-580-7777 Two-chip MicroCapacitance (MC) SIDACtor Device Two-chip MicroCapacitance (MC) SIDACtor Device 1 (T) 2 (G) 3 (R) The two-chip modified TO-220 MC SIDACtor solid state device protects telecommunication equipment in applications that reference Tip and Ring to earth ground but do not require balanced protection. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters VDRM Volts Part Number * VS Volts VDRM Volts Pins 1-2, 3-2 VS Volts VT Volts Pins 1-3 IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0602AC MC 25 40 50 80 4 5 800 2.2 50 60 P1402AC MC 58 77 116 154 4 5 800 2.2 150 60 P1602AC MC 65 95 130 190 4 5 800 2.2 150 60 P2202AC MC 90 130 180 260 4 5 800 2.2 150 50 P2702AC MC 120 160 240 320 4 5 800 2.2 150 50 P3002AC MC 140 180 280 360 4 5 800 2.2 150 50 P3602AC MC 170 220 340 440 4 5 800 2.2 150 40 P4202AC MC 190 250 380 500 4 5 800 2.2 150 40 P4802AC MC 220 300 440 600 4 5 800 2.2 150 40 P6002AC MC 275 350 550 700 4 5 800 2.2 150 40 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 30 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Two-chip MicroCapacitance (MC) SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W PIN 1 Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter PIN 3 PIN 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 31 http://www.teccor.com +1 972-580-7777 Balanced Three-chip SIDACtor Device Balanced Three-chip SIDACtor Device 1 The three-chip modified TO-220 SIDACtor balanced solid state device is designed for telecommunication protection systems that reference Tip and Ring to earth ground. Applications include any piece of transmission equipment that requires balanced protection. This device is built using Teccor's patented "Y" (US Patent 4,905,119) configuration. 3 2 The SIDACtor device is used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20,K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68). Electrical Parameters VDRM Volts Part Number * VS Volts VDRM Volts Pins 1-2, 2-3 VS Volts Pins 1-3 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P1553A_ 130 180 130 180 8 5 800 2.2 150 40 P1803A_ 150 210 150 210 8 5 800 2.2 150 40 P2103A_ 170 250 170 250 8 5 800 2.2 150 40 P2353A_ 200 270 200 270 8 5 800 2.2 150 40 P2703A_ 230 300 230 300 8 5 800 2.2 150 30 P3203A_ 270 350 270 350 8 5 800 2.2 150 30 P3403A_ 300 400 300 400 8 5 800 2.2 150 30 P5103A_ 420 600 420 600 8 5 800 2.2 150 30 A2106A_ ** 170 250 50 80 8 5 800 2.2 120 40 A5030A_ ** 400 550 270 350 8 5 800 2.2 150 30 * For individual "AA", "AB", and "AC" surge ratings, see table below. ** Asymmetrical General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "AA" product. "AB" and "AC" capacitance is approximately 2x the listed value. * Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 32 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Balanced Three-chip SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W PIN 1 Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter PIN 3 PIN 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 33 http://www.teccor.com +1 972-580-7777 Balanced Three-chip MicroCapacitance (MC) SIDACtor Device Balanced Three-chip MicroCapacitance (MC) SIDACtor Device 1 The balanced three-chip TO-220 MC SIDACtor solid state device protects telecommunication equipment in high-speed applications that are sensitive to load values and that require a lower capacitance. CO values for the MC are 40% lower than a standard AC part. 3 2 This MC SIDACtor series is used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968 (formerly known as FCC Part 68) without the need of series resistors. Electrical Parameters VDRM Volts Part Number * VS Volts Pins 1-2, 2-3 VDRM Volts VS Volts Pins 1-3 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P1553AC MC 130 180 130 180 8 5 800 2.2 150 40 P1803AC MC 150 210 150 210 8 5 800 2.2 150 40 P2103AC MC 170 250 170 250 8 5 800 2.2 150 40 P2353AC MC 200 270 200 270 8 5 800 2.2 150 40 P2703AC MC 230 300 230 300 8 5 800 2.2 150 30 P3203AC MC 270 350 270 350 8 5 800 2.2 150 30 P3403AC MC 300 400 300 400 8 5 800 2.2 150 30 P5103AC MC 420 600 420 600 8 5 800 2.2 150 30 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias. * Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 34 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Balanced Three-chip MicroCapacitance (MC) SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 50 C/W PIN 1 Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter PIN 3 PIN 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 35 http://www.teccor.com +1 972-580-7777 LCAS Asymmetrical Multiport Device LCAS Asymmetrical Multiport Device 1 (R1) 6 (T2) 2 (G1) 5 (G2) 3 (T1) 4 (R2) This is an integrated multichip solution for protecting multiple twisted pair from overvoltage conditions. Based on a six-pin surface mount SOIC package, it is equivalent to four discrete DO-214AA or two TO-220 packages. Available in surge current ratings up to 500 A, the multiport line protector is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. For a diagram of an LCAS (Line Circuit Access Switch) application, see Figure 3.21. Electrical Parameters Part Number * VDRM Volts VS Volts VDRM Volts VS Volts CO pF VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 3-2, 6-5, 1-2, 4-5 Pins 3-2, 6-5 Pins 1-2, 4-5 A1220U_4 100 130 180 220 4 5 800 2.2 120 30 A1225U_4 100 130 230 290 4 5 800 2.2 120 30 * For individual "UA", "UB", and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 2x higher. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 36 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide LCAS Asymmetrical Multiport Device Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 4 RqJA Parameter Thermal Resistance: Junction to Ambient 1 2 IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 37 http://www.teccor.com +1 972-580-7777 Data Sheets 3 LCAS Asymmetrical Discrete Device LCAS Asymmetrical Discrete Device These DO-214AA SIDACtor devices are intended for LCAS (Line Circuit Access Switch) applications that require asymmetrical protection in discrete (individual) packages. They enable the protected equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, K.45, IEG 60950, UL 60950, and TIA/EIA-IS-968. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P1200S_ 100 130 4 5 800 2.2 120 40 P2000S_ 180 220 4 5 800 2.2 120 30 P2500S_ 230 290 4 5 800 2.2 120 30 * For individual "SA", "SB", and "SC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "SA" and "SB" product. "SC" capacitance is approximately 10 pF higher. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 38 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide LCAS Asymmetrical Discrete Device Package Symbol Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W RqJA Parameter Thermal Resistance: Junction to Ambient IPP - Peak Pulse Current - %IPP +I +I IITT ISS IH IDRM -V -V +V +V V VTT V VDRM DRM V VS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 39 http://www.teccor.com +1 972-580-7777 Data Sheets Thermal Considerations Four-Port Balanced Three-chip Protector Four-Port Balanced Three-chip Protector This hybrid Single In-line Package (SIP) protects four twisted pairs from overcurrent and overvoltage conditions. Comprised of twelve discrete DO-214AA SIDACtor devices and eight TeleLink surface mount fuses, it is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. Surge current ratings up to 500 A are available. F2 Tip Tip 1 Ring Gnd 18 Ring 19 Z10 Z7 Ring 6 9 F1 Z12 Z11 13 Z4 4 20 17 Z8 Gnd 8 Z1 Tip Z9 Z5 Gnd 3 F8 15 12 Z6 Z2 Ring Tip 10 7 Z3 Gnd F6 F4 5 2 11 14 F3 16 F5 F7 Electrical Parameters VDRM Volts Part Number * VS Volts Pins 2-3, 4-3, 7-8, 9-8, 12-13, 14-13, 17-18, 19-18 VDRM Volts VS Volts Pins 2-4, 7-9, 12-14, 17-19 CO pF VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 1-3 P1553Z_ 130 180 130 180 8 5 800 2.2 150 40 P1803Z_ 150 210 150 210 8 5 800 2.2 150 40 P2103Z_ 170 250 170 250 8 5 800 2.2 150 40 P2353Z_ 200 270 200 270 8 5 800 2.2 150 40 P2703Z_ 230 300 230 300 8 5 800 2.2 150 30 P3203Z_ 270 350 270 350 8 5 800 2.2 150 30 P3403Z_ 300 400 300 400 8 5 800 2.2 150 30 A2106Z_ ** 170 250 50 80 8 5 800 2.2 120 40 A5030Z_ ** 400 550 270 350 8 5 800 2.2 150 30 * For individual "ZA," "ZB," and "ZC" surge ratings, see table below. ** Asymmetrical General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 4-3 and Pins 2-3 at 1 MHz with a 2 V bias and is a typical value for "ZA" product. "ZB" and "ZC" capacitance is approximately 10 pF higher. * Device is designed to meet balance requirements of GTS 8700 and GR 974. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 40 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Four-Port Balanced Three-chip Protector Thermal Considerations Package Symbol Value Unit SIP TJ Operating Junction Temperature Range Parameter -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA +I IPP - Peak Pulse Current - %IPP +I IIT T IISS IIHH IIDRM DRM -V -V +V +V V VTT V VDRM DRM VVS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I tr x td Pulse Waveform 10 6 4 IH 8 25 C 2 IH (TC = 25 C) 14 12 Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 1.2 25 C 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -6 -8 Case Temperature (TC) - C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 41 http://www.teccor.com +1 972-580-7777 Four-Port Longitudinal Two-chip Protector Four-Port Longitudinal Two-chip Protector This hybrid Single In-line Package (SIP) protects four twisted pairs from overcurrent and overvoltage conditions. Comprised of eight discrete DO-214AA SIDACtor devices and eight TeleLink surface mount fuses, it is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. Surge current ratings up to 500 A are available. F2 Tip Gnd 3 Ring 1 Gnd 8 Ring 6 Z8 13 Gnd 18 Ring 19 Z7 11 14 F3 20 17 Z5 9 F1 Tip Z6 Z3 4 F8 15 12 Z4 Z1 Ring Tip 10 7 Z2 Gnd F6 F4 Tip 5 2 F5 16 F7 Electrical Parameters VDRM Volts Part Number * VS Volts Pins 2-3, 4-3, 7-8, 9-8, 12-13, 14-13, 17-18, 19-18 VDRM Volts VS Volts CO pF Pins 2-4, 7-9, 12-14, 17-19 VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 2-3, 3-4 P0602Z_ 25 40 50 80 4 5 800 2.2 50 110 P1402Z_ 58 77 116 154 4 5 800 2.2 150 50 P1602Z_ 65 95 130 190 4 5 800 2.2 150 50 P2202Z_ 90 130 180 260 4 5 800 2.2 150 40 P2702Z_ 120 160 240 320 4 5 800 2.2 150 40 P3002Z_ 140 180 280 360 4 5 800 2.2 150 40 P3602Z_ 160 220 320 440 4 5 800 2.2 150 40 P4202Z_ 190 250 380 500 4 5 800 2.2 150 30 P4802Z_ 220 300 440 600 4 5 800 2.2 150 30 P6002Z_ 275 350 550 700 4 5 800 2.2 150 30 * For individual "ZA," "ZB," and "ZC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured between Pins 4-3 and Pins 2-3 at 1 MHz with a 2 V bias and is a typical value for "ZA" product. "ZB" and "ZC" capacitance is approximately 2x higher. * Device is designed to meet balance requirements of GTS 8700 and GR 974. * Lower capacitance MC versions may be available. Contact factory for further information. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 42 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Four-Port Longitudinal Two-chip Protector Thermal Considerations Package Symbol Value Unit SIP TJ Operating Junction Temperature Range Parameter -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA +I IPP - Peak Pulse Current - %IPP +I IIT T IISS IIHH IIDRM DRM -V -V +V +V V VTT V VDRM DRM VVS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I tr x td Pulse Waveform 10 6 4 IH 8 25 C 2 IH (TC = 25 C) 14 12 Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 1.2 25 C 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -6 -8 Case Temperature (TC) - C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 43 http://www.teccor.com +1 972-580-7777 Four-Port Metallic Line Protector Four-Port Metallic Line Protector The four-port hybrid Single In-line Package (SIP) line protector protects multiple twisted pair from overcurrent and overvoltage conditions. Based on a SIP, it is equivalent to four discrete DO-214AA SIDACtor devices and four surface mount fuses. Available in surge current ratings up to 500 A, this four-port SIP line protector is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. F2 F1 Tip 2 1 Tip Ring 8 7 Z2 Z1 Ring 3 F4 F3 Tip 5 4 Tip Z4 Z3 Ring 6 11 10 Ring 9 12 Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0080Z_ 6 25 4 5 800 2.2 50 100 P0300Z_ 25 40 4 5 800 2.2 50 110 P0640Z_ 58 77 4 5 800 2.2 150 50 P0720Z_ 65 88 4 5 800 2.2 150 50 P0900Z_ 75 98 4 5 800 2.2 150 50 P1100Z_ 90 130 4 5 800 2.2 150 40 P1300Z_ 120 160 4 5 800 2.2 150 40 P1500Z_ 140 180 4 5 800 2.2 150 40 P1800Z_ 170 220 4 5 800 2.2 150 30 P2300Z_ 190 260 4 5 800 2.2 150 30 P2600Z_ 220 300 4 5 800 2.2 150 30 P3100Z_ 275 350 4 5 800 2.2 150 30 P3500Z_ 320 400 4 5 800 2.2 150 30 * For individual "ZA," "ZB," and "ZC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for "ZA" and "ZB" product. "ZC" capacitance is approximately 2x the listed value. * Lower capacitance MC versions may be available. Contact factory for further information. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps A 150 150 90 50 45 20 500 B 250 250 150 100 80 30 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 IPP 10x160 s Amps IPP 10x560 s Amps 2 - 44 IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Four-Port Metallic Line Protector Thermal Considerations Package Symbol Value Unit SIP TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter +I IPP - Peak Pulse Current - %IPP +I IIT T IISS IIHH IIDRM DRM -V -V +V +V V VTT V VDRM DRM VVS S Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I -I tr x td Pulse Waveform 10 6 4 IH 8 25 C 2 IH (TC = 25 C) 14 12 Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 1.2 25 C 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -6 -8 Case Temperature (TC) - C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 45 http://www.teccor.com +1 972-580-7777 Fixed Voltage SLIC Protector Fixed Voltage SLIC Protector These DO-214AA unidirectional protectors are constructed with a SIDACtor device and an integrated diode. They protect SLICs (Subscriber Line Interface Circuits) from damage during transient voltage activity and enable line cards to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/ EIA-IS-968 (formerly known as FCC Part 68). (T/R) (G) For specific design criteria, see details in Figure 3.21. Cathode Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts VF Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0641S_ 58 77 4 5 5 800 1 120 70 P0721S_ 65 88 4 5 5 800 1 120 70 P0901S_ 75 98 4 5 5 800 1 120 70 P1101S_ 95 130 4 5 5 800 1 120 70 * For individual "SA" and "SC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * VDRM is measured at IDRM. * VS and VF are measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for "SA" and "SB" product. "SC" capacitance is approximately 2x the listed value. * Parallel capacitive loads may affect electrical parameters. Surge Ratings (Preliminary Data) Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 C 500 400 200 120 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 46 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Fixed Voltage SLIC Protector Package Symbol Value Unit DO-214AA TJ Operating Junction Temperature Range Parameter -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W Thermal Resistance: Junction to Ambient RqJA +I +I IS IH VS VDRM VT IDRM -V -V IPP - Peak Pulse Current - %IPP VF IT VT +V+V IDRM IH VDRM IS VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 tr td t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form IH 8 6 25 C 4 2 IH (TC = 25 C) 10 Ratio of Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 47 http://www.teccor.com +1 972-580-7777 Data Sheets Thermal Considerations Twin SLIC Protector Twin SLIC Protector 1 (T) Subscriber Line Interface Circuits (SLIC) are highly susceptible to transient voltages, such as lightning and power cross conditions. To minimize this threat, Teccor provides this dualchip, fixed-voltage SLIC protector device. 2 (G) 3 (R) For specific design criteria, see details in Figure 3.23. Electrical Parameters Part Number * VDRM Volts VS Volts VDRM Volts Pins 1-2, 2-3 VS Volts Pins 1-3 VT Volts VF Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0641CA2 58 77 58 77 4 5 5 800 1 120 60 P0721CA2 65 88 65 88 4 5 5 800 1 120 60 P0901CA2 75 98 75 98 4 5 5 800 1 120 60 P1101CA2 95 130 95 130 4 5 5 800 1 120 60 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * VDRM is measured at IDRM. * VS and VF are measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured across pins 1-2 or 2-3 at 1 MHz with a 2 V bias. Capacitance across pins 1-3 is approximately half. * Parallel capacitive loads may affect electrical parameters. * Compliance with GR 1089 or UL 60950 power cross tests may require special design considerations. Contact the factory for further information. Surge Ratings (Preliminary Data) Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 http://www.teccor.com +1 972-580-7777 2 - 48 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Twin SLIC Protector Thermal Considerations Package Symbol Value Unit Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 85 C/W Pin 3 Parameter Thermal Resistance: Junction to Ambient RqJA Pin 2 +I +I VS VDRM IS IH VT IDRM -V -V IPP - Peak Pulse Current - %IPP VF IT VT IDRM VDRM IH IS +V +V VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 td tr t - Time (s) -I -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 49 http://www.teccor.com +1 972-580-7777 Data Sheets Pin 1 Multiport SLIC Protector Multiport SLIC Protector 1 (T1) 6 (T2) 2 (G1) 5 (G2) 3 (R1) 4 (R2) This multiport line protector is designed as a single-package solution for protecting multiple twisted pair from overvoltage conditions. Based on a six-pin SOIC package, it is equivalent to four discrete DO-214AA packages. Available in surge current ratings up to 500 A for a 2x10 s event, the multiport line protector is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. For specific design criteria, see details in Figure 3.24. Electrical Parameters VDRM Volts VS Volts VDRM Volts Pins 1-2, 2-3, 4-5, 5-6 Part Number * VS Volts Pins 1-3, 4-6 VT Volts VF Volts IDRM Amps IS mAmps IT Amps IH mAmps CO pF P0641U_ 58 77 58 77 4 5 5 800 1 120 70 P0721U_ 65 88 65 88 4 5 5 800 1 120 70 P0901U_ 75 98 75 98 4 5 5 800 1 120 70 P1101U_ 95 130 95 130 4 5 5 800 1 120 70 * For individual "UA" and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * VDRM is measured at IDRM. * VS and VF are measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured across pins 1-2, 2-3, 4-5, or 5-6 at 1 MHz with a 2 V bias and is a typical value. Capacitance across pins 1-3 or 4-6 is approximately half. "UC" capacitance is approximately 2x the listed value for "UA" product. * Parallel capacitive loads may affect electrical parameters. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 C 500 400 200 120 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 50 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Multiport SLIC Protector Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 4 Parameter Thermal Resistance: Junction to Ambient RqJA 1 2 +I +I VS VDRM IS IH VT IDRM -V -V IPP - Peak Pulse Current - %IPP VF IT VT IDRM VDRM IH IS +V +V VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 td tr t - Time (s) -I -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 51 http://www.teccor.com +1 972-580-7777 Data Sheets 3 Battrax SLIC Protector Battrax SLIC Protector This solid state protection device can be referenced to either a positive or negative voltage source. The B1xx0C_ is for a -VREF and the B2050C_ is for a +VREF. Designed using an SCR and a gate diode, the B1xx0C_ Battrax begins to conduct at |-VREF| + |-1.2 V| while the B2050C_ Battrax begins to conduct at |+VREF| + |1.2 V|. For a diagram of a Battrax application, see Figure 3.29. Pin 3 (+VREF) Pin 2 (Ground) Pin 1 (Line) Pin 3 (-VREF) Gate Pin 1 (Line) Pin 2 (Ground) -Battrax B1xx0C_ +Battrax B2050C_ Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IGT mAmps IT Amps IH mAmps CO pF B1100C_ |-VREF| + |-1.2 V| |-VREF| + |-10 V| 4 5 100 1 100 50 B1160C_ |-VREF| + |-1.2 V| |-VREF| + |-10 V| 4 5 100 1 160 50 B1200C_ |-VREF| + |-1.2 V| |-VREF| + |-10 V| 4 5 100 1 200 50 B2050C_ |+VREF| + |1.2 V| |+VREF| + |10 V| 4 5 50 1 5 50 * For individual "CA" and "CC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * IPP ratings assume VREF = 48 V. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. "CC" product is approximately 2x the listed value. * Positive Battrax information is preliminary data. * VREF maximum value for the negative Battrax is -200 V. * VREF maximum value for the positive Battrax is 110 V. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 60 50 40 500 C 500 400 200 150 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 52 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Battrax SLIC Protector Thermal Considerations Package Symbol Value Unit Modified DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 85 C/W Pin 3 (VREF) Parameter Thermal Resistance: Junction to Ambient RqJA Pin 1 (Line) Data Sheets Pin 2 (Ground) +I +I +I IT IT VS VDRM -V -V IS IH IS IH VT IDRM IDRM VT IDRM VDRM IH IS -V +V +V +V VT VDRM VS VS IT -I -I -I V-I Characteristics for Positive Battrax 10 6 4 IH 8 25 C 2 IH (TC = 25 C) 14 12 Ratio of Percent of VS Change - % V-I Characteristics for Negative Battrax 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 53 http://www.teccor.com +1 972-580-7777 Battrax Dual Negative SLIC Protector Battrax Dual Negative SLIC Protector This solid state Battrax protection device is referenced to a negative voltage source. Its dual-chip package also includes internal diodes for transient protection from positive surge events. (G) 5 For a diagram of a Battrax application, see Figure 3.27. 1 (T) 2 3 (-VREF) (R) Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts VF Volts IDRM Amps IGT mAmps IT Amps IH mAmps CO pF B1101U_ |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 1 100 50 B1161U_ |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 1 160 50 B1201U_ |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 5 100 1 200 50 * For individual "UA" and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * IPP ratings assume a VREF = -48 V. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. "UC" product is approximately 2x the listed value. * VREF maximum value for the B1101, B1161, and/or B1201 is -200 V. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 C** 500 400 200 120 100 50 500 ** Call factory for release date. http://www.teccor.com +1 972-580-7777 2 - 54 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Battrax Dual Negative SLIC Protector Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 4 Parameter Thermal Resistance: Junction to Ambient RqJA 1 2 +I +I VS VDRM IS IH VT IDRM -V -V IPP - Peak Pulse Current - %IPP VF IT VT IDRM VDRM IH IS +V +V VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 td tr t - Time (s) -I -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 55 http://www.teccor.com +1 972-580-7777 Data Sheets 3 Battrax Dual Positive/Negative SLIC Protector Battrax Dual Positive/Negative SLIC Protector This Battrax device protects Subscriber Line Interface Circuits (SLIC) that use both a positive and negative Ring voltage. It limits transient voltages with rise times of 100 V/ s to VREF 10 V. (+VREF) 4 Ground 2, 5 1 (T) 6 (-VREF) 3 (R) Teccor's six-pin Battrax devices are constructed using four SCRs and four gate diodes. The SCRs conduct when a voltage that is more negative than -VREF (and/or more positive than +VREF) is applied to the cathode (Pins 1 and 3) of the SCR. During conduction, the SCRs appear as a low-resistive path which forces all transients to be shorted to ground. For a diagram of a Battrax application, see Figure 3.30. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IGT mAmps IT Amps IH mAmps CO pF B3104U_ |-VREF| + |1.2V| |-VREF| + |10V| 4 5 100 1 100 50 B3164U_ |-VREF| + |1.2V| |-VREF| + |10V| 4 5 100 1 160 50 B3204U_ |-VREF| + |1.2V| |-VREF| + |10V| 4 5 100 1 200 50 * For individual "UA" and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * IPP ratings assume a VREF = 48 V. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. "UC" product is approximately 2x the listed value. * Positive Battrax information is preliminary data. * VREF maximum value for the negative Battrax is -200 V. * VREF maximum value for the positive Battrax is 110 V. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 C** 500 400 200 120 100 50 500 ** Call factory for release date. http://www.teccor.com +1 972-580-7777 2 - 56 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Battrax Dual Positive/Negative SLIC Protector Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 RqJA 4 Parameter Thermal Resistance: Junction to Ambient 1 3 +I IPP - Peak Pulse Current - %IPP Positive Battrax Characteristics IT IS IH IDRM -V -V +V +V VT VDRM DRM VSS V Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 Negative Battrax Characteristics 0 td tr t - Time (s) -I -I V-I Characteristics tr x td Pulse Wave-form 8 6 25 C 4 Ratio of 2 IH (TC = 25 C) 10 IH Percent of VS Change - % 14 12 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 57 http://www.teccor.com +1 972-580-7777 Data Sheets 2 Battrax Quad Negative SLIC Protector Battrax Quad Negative SLIC Protector This Battrax device is an integrated overvoltage protection solution for SLIC-based (Subscriber Line Interface Circuit) line cards. This six-pin device is constructed using four SCRs and four gate diodes. (+VREF) 4 Ground 2, 5 1 (T) 6 (-VREF) 3 (R) The device is referenced to VBAT and conducts when a voltage that is more negative than -VREF is applied to the cathode (pins 1, 3, 4, or 6) of the SCR. During conduction, all negative transients are shorted to Ground. All positive transients are passed to Ground by steering diodes. For specific diagrams showing these Battrax applications, see Figure 3.28. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IGT mAmps IT Amps IH mAmps CO pF B1101U_4 |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 100 1 100 50 B1161U_4 |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 100 1 160 50 B1201U_4 |-VREF| + |-1.2V| |-VREF| + |-10V| 4 5 100 1 200 50 * For individual "UA" and "UC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * IPP ratings assume a VREF = 48 V. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. "UC" product is approximately 2x the listed value. * VREF maximum value for the negative Battrax is -200 V. Surge Ratings Series IPP 2x10 s Amps IPP 8x20 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s A 150 150 90 50 45 20 500 C 500 400 200 120 100 50 500 http://www.teccor.com +1 972-580-7777 2 - 58 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Battrax Quad Negative SLIC Protector Thermal Considerations Package Symbol Value Unit Modified MS-013 TJ Operating Junction Temperature Range -40 to +125 C TS Storage Temperature Range -65 to +150 C 60 C/W 6 5 RqJA 4 Parameter Thermal Resistance: Junction to Ambient 1 3 +I IPP - Peak Pulse Current - %IPP Positive Battrax Characteristics IT IS IH IDRM -V -V +V +V VT VDRM DRM VSS V Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 Negative Battrax Characteristics 0 td tr t - Time (s) -I -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 59 http://www.teccor.com +1 972-580-7777 Data Sheets 2 CATV and HFC SIDACtor Device CATV and HFC SIDACtor Device 1 3 This SIDACtor device is a 1000 A solid state protection device offered in a TO-220 package. It protects equipment located in the severe surge environment of Community Antenna TV (CATV) applications. Used in Hybrid Fiber Coax (HFC) applications, this device replaces the gas tube traditionally used for station protection, because a SIDACtor device has a much tighter voltage tolerance. Electrical Parameters CO pF Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 1-3 P1400AD 120 160 3 5 800 2.2 50 200 P1800AD 170 220 5.5 5 800 2.2 50 150 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings Series IPP 8x20 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s D 1000 250 120 500 http://www.teccor.com +1 972-580-7777 2 - 60 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide CATV and HFC SIDACtor Device Thermal Considerations Package Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 60 C/W 1 Thermal Resistance: Junction to Ambient Data Sheets RqJA Parameter 3 IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t - Time (s) -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 61 http://www.teccor.com +1 972-580-7777 High Surge Current SIDACtor Device High Surge Current SIDACtor Device 1 (T) 2 (G) 3 (R) This SIDACtor device is a 1000 A solid state protection device offered in a TO-220 package. It protects equipment located in the severe surge environment of Community Antenna TV (CATV) applications. This device can replace the gas tubes traditionally used for station protection because SIDACtor devices have much tighter voltage tolerances. Electrical Parameters CO pF Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 1-3 P6002AD 550 700 5.5 5 800 2.2 50 60 * For surge ratings, see table below. Electrical Parameters CO pF Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps Pins 1-3 P3100AD 280 360 5.5 5 800 2.2 120 115 * For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings Series IPP 8x20 s Amps IPP 10x1000 s Amps ITSM 60 Hz Amps di/dt Amps/s D 1000 250 120 1000 http://www.teccor.com +1 972-580-7777 2 - 62 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide High Surge Current SIDACtor Device Thermal Considerations Symbol Modified TO-220 Value Unit TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 60 C/W RqJA PIN 1 Parameter Thermal Resistance: Junction to Ambient Data Sheets Package PIN 3 PIN 2 Note: P6002AD is shown. P3100AD has no center lead. IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t - Time (s) -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 63 http://www.teccor.com +1 972-580-7777 CATV Line Amplifiers/Power Inserters SIDACtor Device CATV Line Amplifiers/Power Inserters SIDACtor Device 1 2 This SIDACtor device is a 5000 A solid state protection device offered in a non-isolated TO-218 package. It protects equipment located in the severe surge environment of CATV (Community Antenna TV) applications. In CATV line amplifiers and power inserters, this device can replace the gas tubes traditionally used for station protection because SIDACtor devices have much tighter voltage tolerances. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps ** IH mAmps CO pF P1900ME 140 220 4 5 800 2.2/25 50 750 P2300ME 180 260 4 5 800 2.2/25 50 750 * For surge ratings, see table below. ** IT is a free air rating; heat sink IT rating is 25 A. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings Series IPP 8x20 s Amps ITSM 60 Hz Amps di/dt Amps/s E 5000 400 500 http://www.teccor.com +1 972-580-7777 2 - 64 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide CATV Line Amplifiers/Power Inserters SIDACtor Device Package TO-218 Symbol 2 1 2 Value Unit TJ Operating Junction Temperature Range Parameter -40 to +150 C TS Storage Temperature Range -65 to +150 C TC Maximum Case Temperature 100 C RqJC * Thermal Resistance: Junction to Case 1.7 C/W RqJA Thermal Resistance: Junction to Ambient 56 C/W 3 (No Connection) * RqJC rating assumes the use of a heat sink and on state mode for extended time at 25 A, with average power dissipation of 29.125 W. IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t - Time (s) -I tr x td Pulse Wave-form 10 8 6 4 25 C Ratio of 2 IH (TC = 25 C) 14 12 IH Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 20 40 60 80 100 120 140 160 Case Temperature (TC) - C -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Normalized DC Holding Current versus Case Temperature 2 - 65 http://www.teccor.com +1 972-580-7777 Data Sheets Thermal Considerations TeleLink Fuse TeleLink Fuse The TeleLink Surface Mount (SM) surge resistant fuse offers circuit protection without requiring a series resistor. When used in conjunction with the SIDACtor Transient Voltage Suppressor (TVS), the TeleLink SM fuse and the SIDACtor TVS provide a complete regulatory-compliant solution for standards such as GR 1089, TIA/EIA-IS-968, UL 60950, and ITU K.20 and K.21 (formerly known as FCC Part 68). No series resistor is required for the F1250T and F1251T to comply with these standards. Contact factory for enhanced K.20 and K.21 details. Surge Ratings TeleLink SM Fuse IPP 2x10 s Amps IPP 10x160 s Amps IPP 10x560 s Amps IPP 10x1000 s Amps F0500T not rated 75 45 35 F1250T 500 160 115 100 F1251T 500 160 115 100 Interrupting Values TeleLink SM Fuse Voltage Rating Current Rating I2t Measured at DC Rated Voltage Voltage, Current MIN TYP MAX F0500T 250 V 500 mA 1.3 A2s 600 V, 40 A 1s 2s 60 s F1250T 250 V 1.25 A 22.2 A2s 600 V, 60 A * 1s 2s 60 s F1251T 250 V 2A 30 A2s 600 V, 60 A * 1s 2s 60 s Interrupting Rating * Interrupt test characterized at 50 to 70 phase angle. Phase angles approximating 90 may result in damage to the body of the fuse. Notes: * The TeleLink SM fuse is designed to carry 100% of its rated current for four hours and 250% of its rated current for one second minimum and 120 seconds maximum. Typical time is four to 10 seconds. For optimal performance, an operating current of 80% or less is recommended. * I2t is a non-repetitive RMS surge current rating for a period of 16.7 ms. Resistance Ratings DC Cold Resistance TeleLink SM Fuse Typical Voltage Drop @ Rated Current MIN MAX F0500T 0.471 V 0.420 W 0.640 W F1250T 0.205 V 0.107 W 0.150 W F1251T 0.110 V 0.050 W 0.100 W Notes: * Typical inductance @ 4 H up to 500 MHz. * Resistance changes 0.5% for every C. * Resistance is measured at 10% rated current. http://www.teccor.com +1 972-580-7777 2 - 66 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide TeleLink Fuse Qualification Data The F1250T and F1251T meet the following test conditions per GR 1089 without additional series resistance. However, in-circuit test verification is required. Note that considerable heating may occur during Test 4 of the Second Level AC Power Fault Test. Surge Voltage Volts Wave-form s Surge Current Amps Repetitions Each Polarity 1 600 10x1000 100 25 2 1000 10x360 100 25 3 1000 10x1000 100 25 4 2500 2x10 500 10 5 1000 10x360 25 5 Test Second Level Lightning Surge Test Test Surge Voltage Volts Wave-form s Surge Current Amps Repetitions Each Polarity 1 5000 2x10 500 1 First Level AC Power Fault Test Test Applied Voltage, 60 Hz VRMS Short Circuit Current Amps 1 50 0.33 15 min 2 100 0.17 15 min 3 200, 400, 600 1 at 600 V 60 applications, 1 s each 4 1000 1 60 applications, 1 s each Duration 5 * * 60 applications, 5 s each 6 600 0.5 30 s each 7 600 2.2 2 s each 8 600 3 1 s each 9 1000 5 0.5 s each * Test 5 simulates a high impedance induction fault. For specific information, please contact Teccor Electronics. Second Level AC Power Fault Test for Non-Customer Premises Equipment Test Applied Voltage, 60 Hz VRMS Short Circuit Current Amps Duration 1 120, 277 30 30 min 2 600 60 5s 3 600 7 5s 4 100-600 2.2 at 600 V 30 min Notes: * Power fault tests equal or exceed the requirements of UL 60950 3rd edition. * Test 4 is intended to produce a maximum heating effect. Temperature readings can exceed 150 C. * Test 2 may be dependent on the closing angle of the voltage source. Fuse is characterized at 50 to 70. Closing angles approximating 90 may result in damage to the body of the fuse. * Use caution when routing internal traces adjacent to the F1250T and F1251T. (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide 2 - 67 http://www.teccor.com +1 972-580-7777 Data Sheets First Level Lightning Surge Test TeleLink Fuse 1000 800 700 600 500 400 300 200 100 90 80 70 60 50 40 30 20 Time in seconds F0500T F1250T F1251T 10 9 8 7 6 5 4 3 2 1 .9 .8 .7 .6 .5 .4 .3 .2 .1 .09 .08 .07 .06 .05 .04 .03 .02 .01 .1 .2 .3 .4 .5 .6 .7 .8 .9 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 100 Current in Amperes Time Current Curve http://www.teccor.com +1 972-580-7777 2 - 68 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide TeleLink Fuse Temperature Derating Curve Operating temperature is -55 C to +125 C with proper correction factor applied. 150 140 130 Data Sheets Percent of Rating 120 110 100 90 80 70 60 Effect on Current Rating 50 40 30 -55 -60 -40 -20 0 20 40 60 80 100 125 Ambient C Chart of Correction Factor Maximum Temperature Rise TeleLink Fuse Temperature Reading F0500T 75 C (167 F) * F1250T 75 C (167 F) * F1251T 75 C (167 F) * * Higher currents and PCB layout designs can affect this parameter. Notes: * Readings are measured at rated current after temperature stabilizes * The F1250T meets the requirements of UL 248-14. However, board layout, board trace widths, and ambient temperature values can cause higher than expected rises in temperature. During UL testing, the typical recorded heat rise for the F1250T at 2.2 A was 120 C. Package Symbolization Marking F0500T FU F FT F F1250T F1251T Manufactured in Taiwan U T JU J JT J U T NU N NT N (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide Manufactured in USA 2 - 69 U T http://www.teccor.com +1 972-580-7777 TeleLink Fuse http://www.teccor.com +1 972-580-7777 2 - 70 (c) 2002 Teccor Electronics SIDACtor(R) Data Book and Design Guide