Users should evaluate the suitability of this product for their application. Specications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specication, without notication to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.)
OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 2
The TE logo, Tyco Electronics and Raychem are trademarks. Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2008 Tyco Electronics Corporation. All rights reserved.
COMPONENT WIRES - 55PC0111 SHIELD - TIN-COATED COPPER
JACKET - RADIATION-CROSSLINKED,
MODIFIED ETFE
SPECIFICATION CONTROL DRAWING 55PC1141
FOUR CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 2-21-08 B
This specication sheet forms a part of the latest issue of Raychem Specication 55PC.
TITLE Date Revision
CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
SHIELD
SIZE
(AWG)
JACKET THICKNESS
( in. )
OUTSIDE DIAMETER
( in. )
WEIGHT
( lbs/1000 ft. )
LOWER
SPEC
LIMIT
TARGET
WALL
LOWER
SPEC
LIMIT
TARGET
VALUE
UPPER
SPEC
LIMIT
TARGET
VALUE
UPPER
SPEC
LIMIT
55PC1141-26-* 26 38 .0060 .0075 .098 .111 .124 10.86 11.38
55PC1141-24-* 24 38 .0060 .0080 .111 .125 .138 14.03 14.59
55PC1141-22-* 22 38 .0060 .0080 .123 .140 .156 18.57 19.19
55PC1141-20-* 20 38 .0060 .0080 .142 .161 .180 25.67 26.42
55PC1141-18-* 18 38 .0065 .0085 .163 .186 .209 36.10 37.15
55PC1141-16-* 16 38 .0065 .0085 .181 .205 .230 44.44 45.52
55PC1141-14-* 14 38 .0070 .0090 .213 .243 .273 64.85 66.35
55PC1141-12-* 12 38 .0075 .0095 .252 .296 .339 98.21 105.09
55PC1141-10-* 10 36 .0080 .0100 .285 .346 .407 152.70 157.77
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
Revision
SPECIFICATION CONTROL DRAWING Page 2 of 2 B 55PC1141
SCD
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINK VERIFICATION: 300 ± 3°C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND TEST (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The "*" in the part numbers on page 1 shall be replaced by color code designators with
a slash separating the component wire colors and a dash separating the component
wire colors from the jacket color. Colors shown do not necessarily reect the sequence
of manufacturing.
1/ Example: AWG 22, red, yellow, green and blue component wires; white jacket:
55PC1141-22-2/4/5/6-9
1/ See footer section on page 1
