S18-2 Sensors Datasheet Next Generation Self-Contained DC-Operated Sensors * * * * * * Economical photoelectric sensors for cost sensitive and high volume installations Powerful and bright visible red emitter beam for easy alignment and set-up Highly visible output and dual-function power and stability indicators Advanced ASIC technology is resistant to optical and electrical noise source Wide operating temperature range: -40 C to +70 C (-40 F to +158 F) Robust 250 adjustment potentiometer on select models WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Emitter/Receiver Models 1 Model Number Range S18-2NAEL-2M 25 m (82 ft) S18-2NAEJ-2M Emitter 25 m (82 ft) with beam inhibit S18-2NAES-2M S18-2VNRS-2M S18-2VPRS-2M None 25 m (82 ft) with adjustment S18-2VNRL-2M S18-2VPRL-2M Output 25 m (82 ft) Receiver 25 m (82 ft) with adjustment Complementary NPN Complementary PNP Complementary NPN Complementary PNP Polarized Retroreflective Models 1 Model Number S18-2VNLP-2M S18-2VPLP-2M S18-2VNLPC-2M S18-2VPLPC-2M Range 6 m (19.7 ft) with BRT-84 reflector 6 m (19.7 ft) with BRT-84 reflector, with adjustment Output Complementary NPN Complementary PNP Complementary NPN Complementary PNP Retroreflective Models 1 Model Number S18-2VNLV-2M S18-2VPLV-2M Range 7.5 m (24.6 ft) with BRT-84 reflector, with adjustment Output Complementary NPN Complementary PNP 1 Only 2 m (6.5 ft) PVC cable models are listed. To order 9 m (30 ft) PVC cable models, add suffix "9M" (for example, S18-2VNDL-9M). To order 4pin Euro M12 integral QD models, add suffix "Q8" (for example, S18-2VNDL-Q8). To order 4-pin Euro M12 pigtail QD models, add suffix "Q5" (for example, S18-2VNDL-Q5). to order 4-pin Pico M8 pigtail QD models, add suffix "Q3" (for example, S18-VNDL-Q3). Original Document 170670 Rev. E 23 March 2015 170670 S18-2 Sensors Diffuse Models 1 Model Number Range S18-2VNDL-2M Output Complementary NPN 750 mm (29.5 in) with adjustment S18-2VPDL-2M S18-2VNDS-2M Complementary PNP Complementary NPN 300 mm (11.8 in) with adjustment S18-2VPDS-2M Complementary PNP Installing the S18-2 Sensor 1. Amber LED 2. Green LED 3. Gain adjuster 1 3 12 Figure 1. S18-2 Features and Installation To install the S18-2 Sensor: 1. Align the sensor as required for the application. For the most sensitive object detection, align the sensor so that the objects move across the sensor's axis. 2. Secure the sensor to a bracket. 3. Adjust the gain adjuster (sensitivity pot) if necessary. 4. Wire sensor as shown in the wiring diagrams. Wiring Diagrams NOTE: Open lead wires must be connected to a terminal block. Emitter Emitter with Active High Beam Inhibit 3 3 1 2 - 1 10-30V dc 4 + www.bannerengineering.com - Tel: +1-763-544-3164 - 10-30 V dc + 10-30 V dc P/N 170670 Rev. E S18-2 Sensors Complementary Current Sinking (NPN) 3 2 1 - 10-30V dc + 1 4 Complementary Current Sourcing (PNP) 4 Load 2 Load 4-Pin Euro 1 4 + 10-30V dc - 3 Load Load 4-Pin Pico 2 4 3 3 Key 2 1 1 2 3 4 = = = = Brown White Blue Black Specifications Supply Voltage 10 to 30 V dc for ambient temperature 55 C 10 to 24 V dc for ambient temperature > 55 C Supply Current (Exclusive of Load Current) Diffuse: 16 mA Opposed Mode Emitters: 17 mA Opposed Mode Receivers: 8 mA Retroreflective and Polarized Retroreflective: 16 mA Supply Protection Circuitry Protected against reverse polarity and transient voltages Adjustments Diffuse (DL, DS), Emitter (ES), Receiver (RS), Polarized Retroreflective (LPC), Retroreflective (LV) models: Single turn sensitivity (gain) adjustment potentiometer Emitter Beam Inhibit (EJ) models: Tie black wire to 10 to 30 V dc for beam inhibit Construction Housing, connector, gain pot driver: ABS; Front Window: PMMA; Indicator Windows: Clear ABS; Cable: PVC jacket; Pigtail QD: Nickel-plated brass and PVC jacket; Mounting Nuts: 30% glass filled PBT Output Rating Output Protection Circuitry 50 mA total current for ambient temperatures > 55 C Protected against false pulse on power-up and continuous short 100 mA total current through both outputs 55 C circuit of outputs. Short circuit protection at elevated OFF-State Leakage Current: < 50 A at 30 V dc temperature may require a power cycle to reset. ON-State Saturation Voltage: < 1.5 V at 10 mA; < 3.0 V at 100 Emitter LED Wavelength mA All models: 624 nm Output Configuration Output Response Time Complementary PNP or NPN by model number Response is independent of signal strength Environmental Rating Opposed mode: 1.5 milliseconds ON, 1.0 milliseconds OFF IEC 60529 IEC IP67 Retro, Polarized Retro, and Diffuse: 1.5 milliseconds ON, 0.75 milliseconds OFF Vibration and Mechanical Shock Delay on Power-up: 100 milliseconds; outputs do not conduct All models meet Mil. Std. 202F requirements. Method 201A during this time (Vibration; frequency 10 to 60 Hz, max., double amplitude 0.06 in acceleration 10G). Method 213B conditions H&I (Shock: 75G with unit operating; 100G for non-operation) Indicators Three LEDs (1 green, 2 amber) Green solid: indicates power applied and sensor ready Green flashing: indicates marginal sensing signal Amber solid: indicates Pin 4 (black wire) output conducting Repeatability Repeatability is independent of signal strength Opposed mode: 170 microseconds Retro, Polarized Retro, and Diffuse modes: 100 microseconds Operating Conditions Temperature: -40 C to +70 C (-40 F to +158 F) 95% at +50 C maximum relative humidity (non-condensing) Certifications Ind. Cont. Eq. 3TJJ P/N 170670 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 3 S18-2 Sensors Performance Curves Diffuse Models (750 mm Range) Beam Pattern Excess Gain 100 10 EXCESS GAIN BEAM PATTERN (mm) 15 5 0 -5 10 - 10 - 15 0 100 200 300 400 500 600 700 800 1 DISTANCE (mm) 1 10 100 1000 DISTANCE (mm) Diffuse Models (300 mm (Range) Beam Pattern Excess Gain 20 15 5 0 EXCESS GAIN BEAM PATTERN (mm) 1000 10 -5 -10 100 10 -15 -20 0 50 10 0 15 0 20 0 25 0 30 0 35 0 1 40 0 DISTANCE (mm) 10 1 100 1000 10 100 DISTANCE (mm) Emitter/Receiver Models (Effective Beam Size: 15.2 mm) Beam Pattern Excess Gain EXCESS GAIN BEAM PATTERN (mm) 1000 1000 800 600 400 200 0 - 200 - 400 - 600 - 800 - 1000 0 5 10 15 DISTANCE (m) 20 25 100 10 1 0.1 1 DISTANCE (m) 4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 170670 Rev. E S18-2 Sensors Polarized Retroreflective Models Beam Pattern Excess Gain 100 BRT-92x92C BRT-84 BRT-60x40C BRT-40x19A BRT-60x40IP BRT-THG-2-100 40 EXCESS GAIN BEAM PATTERN (mm) 60 20 0 - 20 10 - 40 - 60 0 1 2 3 4 5 6 DISTANCE (m) 1 0.01 0.1 1 10 DISTANCE (m) Retroreflective Models Beam Pattern Excess Gain 100 BRT-92x92C BRT-84 BRT-60x40C BRT-40x19A BRT-60x40IP BRT-THG-2-100 80 40 EXCESS GAIN BEAM PATTERN (mm) 60 20 0 -20 10 -40 -60 -80 0 1 2 3 4 5 6 7 DISTANCE (m) 8 1 0.01 0.1 1 10 DISTANCE (m) Dimensions All measurements are listed in millimeters (inches), unless noted otherwise. Cable Models P/N 170670 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 QD Models 5 S18-2 Sensors Accessories Cordsets 4-Pin Threaded M12/Euro-Style Cordsets Model Length MQDC-406 1.83 m (6 ft) MQDC-415 4.57 m (15 ft) MQDC-430 9.14 m (30 ft) MQDC-450 15.2 m (50 ft) MQDC-406RA 1.83 m (6 ft) MQDC-415RA 4.57 m (15 ft) MQDC-430RA 9.14 m (30 ft) Style Dimensions 44 Typ. Straight M12 x 1 o 14.5 15.2 m (50 ft) 2 1 3 4 32 Typ. [1.26"] 1 2 3 4 30 Typ. [1.18"] Right-Angle MQDC-450RA Pinout (Female) = = = = Brown White Blue Black M12 x 1 o 14.5 [0.57"] 4-Pin Threaded M8/Pico-Style Cordsets Model Length PKG4M-2 2 m (6.56 ft) PKG4M-5 5 m (16.4 ft) PKG4M-9 9 m (29.5 ft) PKW4M-2 2 m (6.56 ft) PKW4M-5 5 m (16.4 ft) Style Dimensions 35 Typ. Straight o 9.5 M8 x 1 4 2 1 3 28 Typ. 20 Typ. Right Angle PKW4M-9 Pinout (Female) 9 m (29.5 ft) 1 = Brown 2 = White 3 = Blue 4 = Black M8 x 1 o 9.5 Apertures 6 Model Units Aperture Description AP18SCN 3 Kit includes round apertures of 0.5 mm (0.02 in), 1.0 mm (0.04 in), and 2.5 mm (0.10 in) diameter. AP18SRN 3 Kit includes round apertures of 0.5 mm (0.02 in), 1.0 mm (0.04 in), and 2.5 mm (0.10 in) diameter. Kits include Teflon(R) FEP(R) lens, o-ring and thread-on housing. APG18S 1 Kit with glass lens to protect plastic sensor lens from chemical environments and weld splatter damage. Product www.bannerengineering.com - Tel: +1-763-544-3164 P/N 170670 Rev. E S18-2 Sensors Brackets For additional brackets, check the current Banner catalog or visit www.bannerengineering.com. All measurements are listed in millimeters, unless noted otherwise. SMB18SF * 18 mm swivel bracket with M18 x 1 internal thread * Black thermoplastic polyester * Stainless steel swivel locking hardware included M18 - 1 x 6G SMBS18-2-1 * 30% glass-filled PBT 51 B 42 4.5 o28 25 A Hole center spacing: A = 36.0 Hole size: A = o 5.3, B = o 18.0 SMB18A * Right-angle mounting bracket with a curved slot for versatile orientation * 12-ga. stainless steel * 18 mm sensor mounting hole * Clearance for M4 (#8) hardware 30 C A B 46 Hole center spacing: A to B = 24.2 Hole size: A = o 4.6, B = 17.0 x 4.6, C = o 18.5 41 SMB18FA.. * Swivel bracket with tilt and pan movement for precision adjustment * Easy sensor mounting to extruded rail T-slots * Metric and inch size bolts available * 18 mm sensor mounting hole 66 B 69 A Hole size: B=o 18.1 Model Bolt Thread (A) SMB18FA 3/8 - 16 x 2 in SMB18FAM10 M10 - 1.5 x 50 SMB18FAM12 n/a; no bolt included. Mounts directly to 12 mm (1/2 in) rods Reflectors BRT-2X2 * * * * * Square, acrylic target Reflectivity factor: 1.0 Max. temperature: +50 C (+122 F) Optional brackets are available Approximate size: 51 mm x 51 mm P/N 170670 Rev. E BRT-84X84A * * * * Square, acrylic target Reflectivity Factor: 2.0 Temperature: -20 C to +60 C (-4 F to +140 F) Approximate size: 84 mm x 84 mm www.bannerengineering.com - Tel: +1-763-544-3164 7 S18-2 Sensors BRT-40X19A * Rectangular, acrylic target * Reflectivity Factor: 1.3 * Temperature: -20 C to +60 C (-4 F to +140 F) * Approximate size: 19 mm x 60 mm overall; 19 mm x 40 mm reflector BRT-84 * Round, acrylic target * Reflectivity Factor: 1.4 * Temperature: -20 C to +60 C (-4 F +140 F) * Optional brackets are available * Approximate size: 84 mm diameter * Mounting Hole: 4.5 mm diameter BRT-60X40C * Rectangular, acrylic target * Reflectivity Factor: 1.4 * Temperature: -20 C to +60 C (-4 F to +140 F) * Optional brackets are available * Approximate size: 40 mm x 60 mm Retroreflective Tape Model Reflectiv ity Factor Maximum Temperatur e Size BRTTHG-2-100 0.7 +60 C (+140 F) 50 mm (2 in) wide, 2.5 m (100 in) long Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. www.bannerengineering.com - Tel: +1-763-544-3164