NSVS792 Dec-01
Application
1575.42MHz GPS
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.0[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 1. Electrical Specifications
Item Spec. Typical
Input and Output Impedance - 50Ω
Nominal Center Frequency (f0) - 1575.42MHz
Insertion Loss 1574.42~1576.42MHz 3.5dB max. 2.8dB
Response Variation 1574.42~1576.42MHz 1.5dB max. 1.0dB
Input and Output VSWR 1574.42~1576.42MHz 2.5 max. 1.8
1475.42MHz 35dB min. 40dB
1535.42MHz 30dB min. 35dB
1615.42MHz 30dB min. 40dB
Out of Band Rejection
(Relative to
Through Level) 1675.42MHz 40dB min. 45dB
(Operating Temperature Range: -40~+85ºC)
Table 2. Maximum Ratings
Item Rating
Maximum Input Power +20dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -40~+85ºC
Storage Temperature -50~+100ºC
JRC SAW FILTER
NSVS792
Communications Equipment Division
Communications Equipment Marketing Department
17-22 Akasaka 2-chome minato-ku,
Tokyo. 107-0052 Japan
Tel. +81 3-3584-8811
Fax. +81 3-3584-8876
http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese)
http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English)
NSVS792 Dec-01
Marking
(1) Manufacture’s Mark
(2) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(3) Part number Mark
Pin no. Connection
1 GND
2 IN/OUT
3 GND
4 GND
5 OUT/IN
6 GND
3.0±0.1
(0.60)
(1.80)
(0.45)
(0.75)
3.0±0.1
1.0±0.1
(0.60)
(0.53)
3
2
1
4
5
6
(a)
(1)
(2)
(3)
(b)
[4x] [2x]
[6x]
Fig.1 Measuring circuit
Fig.2 Package dimensions (in mm)
Fig.3 Desirable land area (in mm)
JGS
18
1
2
34
5
6
SAW
0.93
0.6
0.93 3.8
3.8
2.2 1.15
1.15
IN
50Ω OUT
50Ω
NSVS792 Dec-01
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of so ldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static e lectricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
GPS 1575.42MHz SAW FILTER
NSVS792
Japan Radio Co.,Ltd.
FREQUENCY CHARACTERISTICS
0 0
20 2
40 4
60 6
80 8
100 10
1475.42 1575.42 1675.42
0
20
40
60
0 3000 6000
S21
S11 S22
S11 S22
S21
Frequency [MHz]
Frequency [MHz]
1 1
2 2
3 3
4 4
5 5
6 6
1475.42 1475.42 1575.42 1575.42 1675.42 1675.42
Frequency [MHz] Frequency [MHz]
Insertion Loss [dB]
Insertion Loss [dB]
Insertion Loss [dB]
(1dB Scale)
VSWR
VSWR
