CDB5366 Evaluation Board for CS5366 Features Description ! Single-Ended to Differential Analog Inputs The CDB5366 evaluation board is an excellent means for quickly evaluating the CS5366 24-bit, 192 kHz A/D converter. Evaluation requires only a digital signal analyzer, an analog signal source, and a power supply. ! 3.3 V Logic Interface ! Connection for DSP Serial I/O On-board DIP switches configure the CS5366 in StandAlone mode, avoiding the need for a PC. ! Windows(R)-Compatible CDB5366 Software Supplied by Cirrus to Configure the CS5366 ! On-Board CS8406 to Generate S/PDIF and EIAJ-340 Digital Audio For software-based device configuration, the Control Port mode is used by attaching a host PC to the Evaluation Board and executing the provided FlexGUI software. ! Requires Only an Analog Signal Source, Power Supplies and, optionally, a PC for a Complete Analog-to-Digital-Converter Evaluation System RS232 ORDERING INFORMATION CDB5366 Evaluation Board 8051 Micro USB Control IC or SPI S/PDIF Output RCA 6 Jacks Analog Input Buffers 6 CS5366 A/D Ain+ 6 FPGA Clks/Data Ain- CS8406 AES/EBU S/PDIF Transmitter Optical Coaxial Buffers Audio Clks/Data http://www.cirrus.com Copyright (c) Cirrus Logic, Inc. 2005 (All Rights Reserved) SEPTEMBER '05 DS626DB1 CDB5366 TABLE OF CONTENTS 1. CDB5366 System Overview..................................................................................................................... 3 2. Quick-Start Guide..................................................................................................................................... 3 3. Detailed Board Features .......................................................................................................................... 3 3.1 Stand-Alone Evaluation ............................................................................................................ 3 3.1.1 S1 and S4 Switch Operation .......................................................................................... 4 3.2 Control-Port Evaluation ............................................................................................................ 5 3.3 FlexGUI Hi-Level View ............................................................................................................. 6 3.4 FlexGUI Low-Level View .......................................................................................................... 7 3.5 Bit Definitions ........................................................................................................................... 8 3.5.1 CS5366 Bits .................................................................................................................... 8 3.5.2 FPGA Bits ....................................................................................................................... 8 4. CDB5366 Hardware ................................................................................................................................. 9 4.1 Input and Output Connectors ................................................................................................... 9 4.2 Switches ................................................................................................................................. 10 4.3 User Configuration Jumpers .................................................................................................. 10 4.4 Reserved Factory Programming Jumpers ............................................................................. 10 4.5 Power Supply Circuitry ........................................................................................................... 11 4.6 Grounding and Power Supply Treatment ............................................................................... 11 4.7 FPGA Hardware ..................................................................................................................... 11 4.8 CS8406 S/PDIF Audio Transmitter ........................................................................................ 11 4.9 Serial Audio Interface ............................................................................................................. 11 4.10 Analog Input Buffer .............................................................................................................. 11 5. Schematics............................................................................................................................................. 12 6. Board Layout and Routing Plots ........................................................................................................... 21 7. Revision History ..................................................................................................................................... 24 LIST OF FIGURES Figure 1. Hi-Level FlexGUI View ................................................................................................................. 6 Figure 2. FlexGUI Low-Level Register View ............................................................................................... 7 Figure 3. FPGA Low-Level Bit View ............................................................................................................ 8 Figure 4. CS5366 (Schematic page 1) ...................................................................................................... 12 Figure 5. Clock Generation (Schematic page 2) ....................................................................................... 13 Figure 6. FPGA (Schematic page 3) ......................................................................................................... 14 Figure 7. Control Port (Schematic page 4) ................................................................................................ 15 Figure 8. Clock and Data Buffers (Schematic page 5) .............................................................................. 16 Figure 9. CD8406 S/PDIF Output (Schematic page 6) ............................................................................. 17 Figure 10. Analog Inputs 1 to 4 (Schematic page 7) ................................................................................. 18 Figure 11. Analog Inputs 5 to 8 (Schematic page 8) ................................................................................. 19 Figure 12. Power (Schematic page 9) ....................................................................................................... 20 Figure 13. Top Silkscreen ......................................................................................................................... 21 Figure 14. Top Layer ................................................................................................................................. 22 Figure 15. Bottom Layer ............................................................................................................................ 23 LIST OF TABLES Table 1. CDB5366 Input and Output Connectors ....................................................................................... 9 Table 2. CDB5366 Switches ..................................................................................................................... 10 Table 3. User Jumpers .............................................................................................................................. 10 Table 4. CDB5366 Reserved Jumpers ..................................................................................................... 10 2 DS626DB1 CDB5366 1. CDB5366 SYSTEM OVERVIEW The CDB5366 Evaluation Board provides an excellent means of quickly evaluating the CS5366. A digital audio interface transmitter (CS8406) provides an easy interface to digital audio signal analyzers, including the majority of digital audio test equipment. Standard analog input and digital output connectors are included for quick and reliable board setup. An on-board FPGA is used for configuring the various modes of the CS5366. Graphical User Interface software is supplied by Cirrus Logic, which allows programming the CDB5366 when connected to a host PC running Microsoft Windows(R). 2. QUICK-START GUIDE * Confirm that DIP switches S1 and S4 are in the closed (LO) position, pushed down to the right. * Connect the following jumpers. - J7 - Install 5 jumpers to the left side of J7, enabling the DIP switches to operate correctly. - J81, J95 - Install jumpers to these positions, grounding XTI and XTO of the CS5366. - J1 - Install a jumper at the +5 V position, allowing VA to be supplied by the +5 V supply. * Install a 12.288 MHz canned Oscillator to socket Y1, providing a Master Timing Clock for the system. * Install a jumper to J11 at the OSC position to enable the OSC drive buffer. * Connect power supply common to the GND binding post. Connect +5 V, +12 V and -12 V to the binding posts as marked on the board silkscreen This configuration provides a completely operational 24-bit Analog-to-Digital-Converter evaluation system. The CS5366 is operating as a Master Device in Single Speed Mode with a 48 kHz sampling rate. Apply power and connect analog input signals of 1 Vrms maximum (full scale) to the RCA inputs jacks. S/PDIF Digital audio data is available for evaluation at the Optical and Coaxial outputs. 3. DETAILED BOARD FEATURES The CDB5366 Evaluation Board supports both the Stand-Alone and Control Port modes of the CS5366. An FPGA (U2) controls digital signal routing between the CS5366, the CS8406 and the DSP I/O header. For user-friendly evaluation of the TDM interface, the FPGA will translate TDM data into PCM data and send it to the CS8406. 3.1 Stand-Alone Evaluation In Stand-Alone mode, the CDB5366 runs without an external PC attached. In this mode, the FPGA controls operation of the board by dynamically reading DIP switches (S1 and S4) after a cold power-up or a pushbutton board reset. Stand-Alone mode provides the most commonly used device settings. For additional control of the CS5366, Control Port mode is used. In Stand-Alone mode, as the DIP switches are repositioned, the FPGA simultaneously sets the appropriate pins on the CS5366 and CS8406 to keep them synchronized with regard to sampling speed and data format. DS626DB1 3 CDB5366 3.1.1 S1 and S4 Switch Operation DIP Switch S1 contains six switches that function as described below. M1,M0 set the device Speed Mode 0x00 Single Speed Master 0x01 Double Speed Master 0x10 Quad Speed Master 0x11 Slave all speed DIF1,DIF0 set the Digital Audio Interface Data format 0x00 Left Justified 0x01 IS 0x10 TDM 2-wire 0x11 TDM 4-wire TDM1 and TDM0 support both TDM mode and PCM mode. In TDM mode, TDM1 and TDM0 select two stereo pairs from a TDM stream, convert the data to Left-Justified PCM format then send the data to the CS8406 S/PDIF transmitter. 0x00 TDM Pair 1 (Channel 1, 2) 0x01 TDM Pair 2 (Channel 3, 4) 0x10 TDM Pair 3 (Channel 5, 6) 0x11 Reserved In PCM mode, TDM1 and TDM0 select which SDOUT is sent to the CS8406. 0x00 SDOUT1 (Channel 1, 2) 0x01 SDOUT2 (Channel 3, 4) 0x10 SDOUT3 (Channel 5, 6) 0x11 Reserved DIP Switch S4 contains two switches which function as described below.7 MDIV - divides the master clock by 2 when OPEN (HI). CLKMODE - divides the master clock by 1.5 when OPEN (HI) 4 DS626DB1 CDB5366 3.2 Control-Port Evaluation The CDB5366 is shipped with a Cirrus Logic designed Microsoft Windows-based program that allows full control over the CS5366 internal registers. This software program is called the FlexGUI, and it is loaded by executing the FlexLoader.exe file. Hardware interface to the FlexGUI is provided by connecting an RS-232 cable or a USB cable between a host PC and the CDB5366. Once the FlexGUI is loaded, the Evaluation Board DIP switches are ignored, and all register settings are available for reading and writing using software control. Testing configurations may be quickly reproduced by using the FlexGUI to save and restore unique register settings. Configure the board for Control Port operation using the instructions that follow. * Connect jumpers. - J7 - Install 5 jumpers to the left side of J7, enabling the IC control interface. - J81, J95 - Install jumpers to these positions, grounding XTI and XTO of the CS5366. - J9 - Install a jumper at the +5 V position, allowing VA to be supplied by the +5 V supply (VA may be externally supplied at the VA binding post by moving jumper J9 to the VA EXT position). * Add an oscillator of choice to socket Y1 to provide a Master Timing Clock for the system. A crystal may also be used by removing the canned oscillator and jumpers J81, J95 and J11. The CDB5366 Evaluation Board is shipped with 39 pF loading capacitors for crystal-based oscillators. Soldering pads are provided on the board for users that require third overtone tank circuit operation or different loading capacitors. * Connect the power supply common to the GND binding post. Connect +5 V, +12 V and -12 V to the binding posts as marked on the board silkscreen. The FlexGUI provides two convenient views of the CDB5366 Evaluation Board settings. The default view is a high-level functional mapping of settings. The second view is a lower-level register map view for programming at the bit level. Each view is synchronized with the other view, so that changing a setting at one level will also change the corresponding setting in the alternate level. DS626DB1 5 CDB5366 3.3 FlexGUI Hi-Level View The Cirrus Logic FlexGUI defaults to the Hi-Level View as shown in Figure 1. This view provides functionally grouped control over the CS5366, reducing the need to memorize the exact location of bit settings. Any register may be modified at any time; however, the effect of changes made to the CS5366 is gated off until the Control Port Bit is enabled. When switching to TDM mode, the CS8406 Clock and Date source (Board Control Panel) must be changed prior to changing the CS5366 SAI format. This sequential ordering resets the FPGA to assure that it timed properly with the CS5366 TDM packet stream. Figure 1. Hi-Level FlexGUI View 6 DS626DB1 CDB5366 3.4 FlexGUI Low-Level View The Low-level Register Map view provides direct control over the CS5366, the FPGA and GPIO settings that change the CS5366 device address. Select the desired device tab; then select and modify any writeregister values. Register modification is always a READ-WRITE-READ operation and is usable at both the byte or bit level. For byte-level control, type the required hex value in the desired register field numerical box. For bit-level control, click the corresponding graphical push-button in the desired register field or use the pull-down menu to access and change the bit values. Figure 2. FlexGUI Low-Level Register View When the CS5366 is put in Control Port mode, the DIP switches are ignored and configuration is determined by the register bits. When placed back in Stand-Alone mode, the DIP switches regain board control. Exiting Control Port mode is achieved by stopping the FlexGUI program. Once the program is stopped, about three seconds later, Stand-Alone mode is established. DS626DB1 7 CDB5366 3.5 3.5.1 Bit Definitions CS5366 Bits The Low-Level view of the FlexGUI provides the full register set of the CS5366 under the CS5366 tab. The CS5366 datasheet provides full details of internal register operation. 3.5.2 FPGA Bits FPGA Register 0x00 is non-functional and only contains the revision code of the FPGA. FPGA Register 0x01 is a functional register that provides the following functionality. Figure 3. FPGA Low-Level Bit View Fs_Range1,0 set the device Speed Mode. These bits need to be changed when using the Serial Audio Interface of the DSP header to communicate with external equipment. 0x00 Single Speed Master 0x01 Double Speed Master 0x10 Quad Speed Master 0x11 Slave all speed AudioFMT1,0 set the Serial Audio Interface format when attaching the Serial Audio Interface of the DSP header to external equipment. 0x00 Left Justified 0x01 IS 0x10 TDM 2-wire 0x11 TDM 4-wire 8 DS626DB1 CDB5366 In TDM mode, SDOUT_SEL1 and SDOUT_SEL 0 extract two stereo pairs from the CS5366 TDM stream, convert the data to Left-Justified PCM format and send the data to the CS8406 data input pin. 0x00 TDM Pair 1 (Channel 1, 2) 0x01 TDM Pair 2 (Channel 3, 4) 0x10 TDM Pair 3 (Channel 5, 6) 0x11 Reserved In PCM mode, SDOUT_SEL1 and SDOUT_SEL 0 select which SDOUT pin of the CS5366 is sent to the CS8406. 0x00 SDOUT1 (Channel 1, 2) 0x01 SDOUT2 (Channel 3, 4) 0x10 SDOUT3 (Channel 5, 6) 0x11 Reserved TDM2PCM/PCM selects the clock source for the CS8406. 0x00 8406 Clock Source is CS5366 0x01 8406 Clock Source is the FPGA TDM2PCM engine 4. CDB5366 HARDWARE The CDB5366 Evaluation Board has a number of connections, switches and jumpers that provide ease and convenience for quickly evaluating the most commonly used functions of the CS5366 silicon device. The following tables list the purpose of each hardware option on the Evaluation Board. 4.1 Input and Output Connectors The input and output connectors provide power and signal connectivity to the CDB5366 Evaluation Board as shown in Table 1. DESIGNATOR NAME CLASS FUNCTION J6 GND Ground Ground connection from power supply J2 +5 V Power + 5 Volt power for CS5366 J16 +12 V Power +12 V power for the active input buffers J17 -12 V Power -12 V power for the active input buffers J18 AIN6 Analog Input Analog input channel 6 J19 AIN5 Analog Input Analog input channel 5 J20 AIN1 Analog Input Analog input channel 1 J21 AIN2 Analog Input Analog input channel 2 J22 AIN4 Analog Input Analog input channel 4 J23 AIN3 Analog Input Analog input channel 3 OPT1 Optical Output Digital Output S/PDIF Optical Digital audio output J3 Coax Output Digital Output S/PDIF Coaxial Digital audio output J5 RS232 I/O Digital I/O FlexGUI Interface port to PC J10 USB I/O Digital I/O FlexGUI Interface port to PC Table 1. CDB5366 Input and Output Connectors DS626DB1 9 CDB5366 4.2 Switches The CDB5366 Evaluation Board switches are used for setting speed modes and format protocols and for resetting devices to their default state. The switch functions are described in Table 2. . DESIGNATOR NAME FUNCTION (see CS5366 Datasheet for details) S1-1 M0 speed mode; Master/Slave function S1-2 M1 speed mode; Master/Slave function S1-3 DIF0 Data Format S1-4 DIF1 Data Format S1-5 TDM0 Select Channel pairs for S/PDIF output S1-6 TDM1 Select Channel pairs for S/PDIF output S4-1 MDIV Master Clock Divider S4-2 CLKMODE Master Clock Divider S3 BOARD RESET Resets CS5366, CS8406 and FPGA S2 PGM Forces FPGA to be loaded with new code (not needed by user) Table 2. CDB5366 Switches 4.3 User Configuration Jumpers The CDB5366 Evaluation Board jumpers are used for signal routing as shown in Table 3 . DESIGNATOR NAME FUNCTION J7 CONTROL Select IC control Source J91 - Short to ground when not using Crystal J85 - Short to ground when not using Crystal J11 OSC/XTL Canned Oscillator/Crystal Selection J9 +5 V/VA EXT VA source selector J4 DSP HEADER Table 3. User Jumpers 4.4 Reserved Factory Programming Jumpers The CDB5366 Evaluation Board has two reserved headers, J15 and J8, that are used to factory program the Cygnal(R) 8051 microprocessor and the Xilinx(R) FPGA so that the FlexGUI interface operates correctly. Caution! Do not apply power or shorts to these two jumpers as device damage could occur. . DESIGNATOR NAME FUNCTION J15 MICRO_PROG Reserved interface for pre-programming the Evaluation Board J8 JTAG Reserved interface for pre-programming the Evaluation Board Table 4. CDB5366 Reserved Jumpers 10 DS626DB1 CDB5366 4.5 Power Supply Circuitry Power is applied to the evaluation board through five binding posts (+5 V, +12 V, -12 V, VA and GND). The GND connection is the common reference for power supplies. The +5 V binding post supplies digital power for all logic devices. The +12 V and -12 V binding posts supply power for the Operational Amplifier input buffers. The VA binding posts supplies power to the Analog Reference. 4.6 Grounding and Power Supply Treatment As a high-peformance mixed-signal device, the CS5366 requires careful attention to power and grounding arrangements to optimize CS5366 performance. The CDB5366 Evaluation Board provides an excellent reference example of an optimum two-layer board layout that places decoupling capacitors as close to the CS5366 as possible and provides ground plane fill on both top and bottom layers. 4.7 FPGA Hardware The on-board FPGA is utilized for several purposes. In addition to providing a method for configuring the CS5366 in Software mode, it contains its own configuration registers that provide clock and data routing for Master and Slave modes of the CS5366. The FPGA contains a multiplexer that selects which SDOUT line is routed to the CS8406. It also contains a TDM2PCM engine that extracts channel pairs from a TDM stream and sends them to the CS8406. 4.8 CS8406 S/PDIF Audio Transmitter The system generates standard S/PDIF data using a CS8406 192 kHz Digital Audio Transmitter. The CS8406 receives input data from the FPGA in PCM format and transmits S/PDIF data on both optical and coaxial output connectors. The optical output connector is limited to a maximum speed of 96 kHz. The coaxial connector supports Quad Speed 192 kHz clocking rates. 4.9 Serial Audio Interface In addition to the standard S/PDIF outputs, the Customer Evaluation Board has been designed to allow Master and Slave operation using the Serial Audio Interface (SAI) via the 14-pin header, J4, which includes the signals MCLK, SCLK, LRCK, and the four serial data lines. When the CS5366 is in Slave mode, SCLK and LRCK/FS must be supplied externally through the J4 header. 4.10 Analog Input Buffer The CDB5366 includes an example of an active low-noise, single-ended-to-differential analog input buffer shown in the schematic drawings, Figures 10 and 11. Alternate active or passive, single-ended or differential topologies may be used as cost dictates. However, the high performance of the CS5366 may be compromised. Optimum device performance is met by buffering the CS5366 with a low noise structure that is stable with a 2700 pF output load. DS626DB1 11 12 5. SCHEMATICS CDB5366 DS626DB1 Figure 4. CS5366 (Schematic page 1) DS626DB1 Figure 5. Clock Generation (Schematic page 2) CDB5366 13 14 CDB5366 DS626DB1 Figure 6. FPGA (Schematic page 3) DS626DB1 15 CDB5366 Figure 7. Control Port (Schematic page 4) 16 Figure 8. Clock and Data Buffers (Schematic page 5) CDB5366 DS626DB1 17 Figure 9. CD8406 S/PDIF Output (Schematic page 6) CDB5366 DS626DB1 DS626DB1 Figure 10. Analog Inputs 1 to 4 (Schematic page 7) CDB5366 18 19 Figure 11. Analog Inputs 5 to 8 (Schematic page 8) CDB5366 DS626DB1 DS626DB1 Figure 12. Power (Schematic page 9) CDB5366 20 21 6. BOARD LAYOUT AND ROUTING PLOTS CDB5366 DS626DB1 Figure 13. Top Silkscreen 22 CDB5366 DS626DB1 Figure 14. Top Layer DS626DB1 23 CDB5366 Figure 15. Bottom Layer CDB5366 7. REVISION HISTORY Release DB1 Date September 2005 Changes Initial Release Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to <http://www.cirrus.com/corporate/contacts/sales.cfm> IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo and designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. IC is a registered trademark of Philips Semiconductor. Microsoft Windows is a registered trademark of Microsoft Corporation. Cygnal is a registered trademark of Silicon Laboratories, Inc. Xilinx is a registered trademark of Xilinx, Inc. 24 DS626DB1