©2010-2014 by Murata Electronics N.A., Inc.
SF2069A-1 (R) 4/4/14 Page 1 of 2 www.murata.com
RFM products are now
Murata products.
Electrical Characteristics
Characteristic Sym Notes Min Typ Max Units
Nominal Center Frequency ( @ 25°C ) fO
1
95.9 96.00 96.1 MHz
Minimum Insertion Loss Attenuation 14 16 dB
Passband αmin ≤ 1dB , B1dB 4.3 5.0 MHz
Amplitude Ripple (p-p) ±2.40MHz 0.8 1.5 dB
Group Delay Ripple ±2.40MHz 80 125 ns
Relative Attenuation (relative to αmin)
40 to 87 MHz 43 48 dB
111 to 150 MHz 50 55 dB
Operating Temperature TA1-40 +85°C
Impedance Matching to 50 Ω unbalanced External L-C
Case Style SMP-75 19 x 6.5 mm Nominal Footprint
Lid Symbolization (YY = year, WW = week) RFM SF2069A-1 YYWW
• Low Insertion Loss
• Hermetic 19 x 6.5 mm Surface-mount Case
• Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating Value Units
Maximum Incident Power in Passband +10 dBm
Max. DC voltage between any 2 terminals 30 VDC
Storage Temperature Range -40 to +150 °C
Suitable for lead-free soldering - Max. Soldering Profile 260°C for 30 s
96.00 MHz
SAW Filter
SF2069A-1
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 W and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
Pb
SMP-75
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
©2010-2014 by Murata Electronics N.A., Inc.
SF2069A-1 (R) 4/4/14 Page 2 of 2 www.murata.com
Case Dimensions
Dimension mm Inches
Min Nom Max Min Nom Max
A18.80 19.00 19.30 0.740 0.748 0.760
B6.30 6.50 6.80 0.248 0.256 0.268
C1.75 2.00 0.069 0.079
D2.29 0.090
E1.02 0.040
H1.0 0.039
P1.905 0.075
Electrical Connections
Connection Terminals
Port 1 Hot 10
Ground Return 1
Port 2 Hot 5
Ground Return 6
Case Ground All others
Single Ended Operation Return is ground
Differential Operation Return is hot
Materials
Solder Pad
Termination
Au plating 30 - 60 µinches (76.2-152 µm) over 80-200
µinches (203-508 µm) Ni.
Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phos-
phorus) 100-200 µinches Thick
Body Al2O3 Ceramic
Pb Free
10-Terminal Ceramic Surface-Mount Case
19 x 6.5 mm Nominal Footprint
SMP-75 Case
A
BC
H
P (8 Places)
E (10 Places)
6
7
8
9
10
5
4
3
2
1
D
TOP VIEW BOTTOM VIEW
5
4
3
2
1
6
7
8
9
10
