www.infineon.com
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to oer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon oers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
Copyrights
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 2
© Cypress Semiconductor Corporation, 2015-2019. This document is the property of Cypress Semiconductor Corporation and its
subsidiaries (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned
by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights
under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights,
trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have
a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive,
nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source
code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization,
and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors),
solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any
other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be
absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no
liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT
REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS,
WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER
SECURITY INTRUSION (collectively, “Security Breach”). Cypress disclaims any liability relating to any Security Breach, and you shall and
hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described
in these materials may contain design defects or errors known as errata which may cause the product to deviate from published
specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further
notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any
information provided in this document, including any sample design information or programming code, is provided only for reference
purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any
application made of this information and any resulting product. “High-Risk Device” means any device or system whose failure could cause
personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and
other medical devices. “Critical Component” means any component of a High-Risk Device whose failure to perform can be reasonably
expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in
whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress
product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, its directors, officers, employees, agents,
affiliates, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including
claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component
in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except
to the limited extent that (i) Cypress’s published data sheet for the product explicitly states Cypress has qualified the product for use in a
specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the
specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and
Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress
trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 3
Preface
This manual explains how to use the evaluation board. Be sure to read this manual before using the product. For this
product, please consult with sales representatives or support representatives.
Handling and Use
Handling and use of this product and notes regarding its safe use are described in the manuals.
Follow the instructions in the manuals to use this product.
Keep this manual at hand so that you can refer to it anytime during use of this product.
Notice on this Document
All information included in this document is current as of the date it is issued. Such information is subject to change without
any prior notice.
Please confirm the latest relevant information with the sales representatives.
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 4
Cautions
Caution of the Products Described in this Document
The following precautions apply to the product described in this manual.
WARNING
Indicates a potentially hazardous situation which could result in death or serious injury and/or a fault in the
user’s system if the product is not used correctly.
WARNING
Do not look directly at LED. There is a possibility that your eye is hurt.
Electric shock,
Damage
Before performing any operation described in this manual, turn off all the power supplies to the system.
Performing such an operation with the power on may cause an electric shock or device fault.
Electric shock,
Damage
Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.
CAUTION
Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or
devices connected to it, or may cause to loose software resources and other properties such as data, if the
device is not used appropriately.
Cuts, Damage
Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your step
when carrying the product. Do not use the product in an unstable location such as a place exposed to strong
vibration or a sloping surface. Doing so may cause the product to fall, resulting in an injury or fault.
Cuts
The product contains sharp edges that are left unavoidably exposed, such as jumper plugs.
Handle the product with due care not to get injured with such pointed parts.
Damage
Do not place anything on the product or expose the product to physical shocks. Do not carry the product after
the power has been turned on.
Doing so may cause a malfunction due to overloading or shock.
Damage
Since the product contains many electronic components, keep it away from direct sunlight, high temperature,
and high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust
or a strong magnetic or electric field for an extended period of time. Inappropriate operating or storage
environments may cause a fault.
Damage
Use the product within the ranges given in the specifications.
Operation over the specified ranges may cause a fault.
Damage
To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal
parts of any of the connectors. Before handling the product, touch a metal object (such as a door knob) to
discharge any static electricity from your body.
Damage
When turning the power on or off, follow the relevant procedure as described in this document. Before turning
the power on, in particular, be sure to finish making all the required connections. Furthermore, be sure to
configure and use the product by following the instructions given in this document. Using the product
incorrectly or inappropriately may cause a fault.
Damage
Because the product has no casing, it is recommended that it be stored in the original packaging. Transporting
the product may cause a damage or fault. Therefore, keep the packaging materials and use them when re-
shipping the product.
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 5
Contents
1. Description .................................................................................................................................................................. 6
2. Evaluation Board Specification ................................................................................................................................. 7
3. Pin Descriptions ......................................................................................................................................................... 8
3.1 Input/Output Connecter Descriptions .................................................................................................................. 8
3.2 Switch Descriptions ............................................................................................................................................ 8
4. Setup and Verification ................................................................................................................................................ 9
4.1 Contents in a Package ....................................................................................................................................... 9
4.2 Evaluation with BLE Communication .................................................................................................................. 9
4.3 Function of Application ..................................................................................................................................... 13
4.4 How to Do When LED Lighting can not be Controlled. ..................................................................................... 17
5. Layout ........................................................................................................................................................................ 18
5.1 Component Layout ........................................................................................................................................... 18
5.2 Wiring Layout.................................................................................................................................................... 19
6. Circuit Schematic ..................................................................................................................................................... 20
7. Component List ........................................................................................................................................................ 23
8. Property Data ............................................................................................................................................................ 26
9. Board Picture ............................................................................................................................................................ 29
10. Ordering Information ................................................................................................................................................ 30
Revision History ................................................................................................................................................................ 31
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 6
1. Description
S6SAL211A94SA1001 is the starter kit tool for BLE (*1) communication.
The tool has one evaluation board, this board implements S6AL211A94, and LED driver controlled by BLE communication.
It is necessary to prepare AC power cable, Android terminal (*2), Application software, LED module and connection cable.
*1: BLE: Bluetooth® Low Energy
*2: Prepare an Android terminal with Android OS 4.4.2 or 4.4.4.
Figure 1-1 Board Outline
Android terminal
*Android4.4.2 or 4.4.4
S6SAL211A94SA1001 LED,Thermistor
AC power cable
AC 85V-264V
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 7
2. Evaluation Board Specification
Figure 2-1 Evaluation Board Specification
Item
Symbol
Min.
Typ.
Max.
Unit
Input voltage (with TUHS10F24)
VINAC
85
264
VRMS
Output LED voltage
VLEDout
0
18
24
V
Output LED current
ILEDout(W)
ILEDout(R)
ILEDout(G)
ILEDout(B)
-
-
290
140
180
90
mA
Board size
-
58 93
mm
.
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 8
3. Pin Descriptions
3.1 Input/Output Connecter Descriptions
Table 3-1 Input/Output Pin Descriptions
Connecter Symbol
I/O
Function Description
CN_AC
I
AC power supply terminal
ACDC_OUT
O
24V AC/DC module output
ACDC_GND
-
GND
CN009
I/O
CH1 - CH4 LED , thermistor terminal
MS_3V
O
3V power supply terminal for motion sensor
MS_IN
I
Input terminal for motion sensor
MS_GND
-
GND terminal for motion sensor
LSp
O
3V power supply terminal for Illumination sensor
LSm
I
Input terminal for Illumination sensor
LSg
-
GND terminal for Illumination sensor
CN061
I/O
JTAG terminal for BLE module
3.2 Switch Descriptions
Table 3-2 Switch Descriptions
Switch
Description
SW062
Reset push switch for BLE module
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 9
4. Setup and Verification
4.1 Contents in a Package
Table 4-1 S6SAL211A94SA1001 Contents List
No.
Contents
Description
Quantity
Notes
1
S6SAL211A94-BLE-SA1
Evaluation board of 4CH 10W with S6AL211A94
1
-
2
Leaflet
Described startup information
2
English, Japanese
Figure 4-1 Contents Picture
1
2
4.2 Evaluation with BLE Communication
Using Items for Evaluation with I2C Control
Evaluation board 1pic (*1)
AC power cable 1pic (*2)
Android terminal with Android OS 4.4.2 or 4.4.4. 1pic (*2)
Application software 1pic (*3)
LED module(5 series 4ch) 1set (*2)
Connection cable 1set (*2)
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 10
*1: Included in a package.
*2: Please prepare. Refer to 4.2.1 Operation
*3: Please download it from our device home page.
URL: http://www.cypress.com/S6AL211A
S6AL211A94: BLE Application software file BLExLED.apk in S6AL211_BLExLED.cab
4.2.1 Operation
WARNING
Do not look directly at LED. There is a possibility that your eye is hurt.
1. Connect CN009 of the evaluation board and LED by connection cable. (*1)
2. Set some attributes in the application of Android terminal. (*2)
3. Connect AC plug of the evaluation board to AC power supply.
4. Connect Android terminal to BLE module by BLE communication. (*2)
5. When connection succeeds, it is possible to make them do various movement by application. (*3)
6. When ending operation, make the brightness level of the LED "0" and tap "Disconnect" button of "HOME" tab and
cut power supply.
Figure 4-2 Board Connection
*1: Connect LED to all CH from CN009. Refer to 4.2.1.1 Connection of the Evaluation Board and LED.
*2: Refer to 4.2.1.2 Setup with BLE Communication.
*3: Refer to 4.3 Function of Application.
Android
terminal
Evaluation Board
LED,Thermistor
(*1)
CN009
AC power cable
Connection cable(*1)
AC 85V-264V
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 11
4.2.1.1 Connection of the Evaluation Board and LED
Figure 4-3 Connection of the Evaluation Board and LED
*1: Connect LED to CN009.
Driver's output channel and color of LED are fixing by application software.
To indicate correct color, connect each channel exactly.
Specification of LED module and resistor: LED (5-series) + resistor
White: IF ≥ 1A, VF ≈ 3 V Ex: LUW CR7P(OSRAM)
Red: IF ≥ 1A, VF ≈ 2.2 V Ex: LR CP7P(OSRAM)
Green: IF ≥ 1A, VF ≈ 3.2 V Ex: LT CP7P(OSRAM)
Blue: IF ≥ 1A, VF ≈ 3.2V Ex: LB CP7P(OSRAM)
R: 10Ω 2W
Be careful about polarity.
*2: Thermistor (+TH,-TH) is an option. Even if that isn't connected, a board operates.
Ex: NTCG104EF104FT1 (TDK)
Evaluation board
1 +LED1
LED,Thermistor
CH1: White
CH2: Red
CH3: Green
CH4: Blue R
R
R
R
2.54mm 10pin ×2
Connector
CN009
19 +TH4
17 +LED4
15 NC
13 +TH3
11 +LED3
9 +TH2
7 +LED2
5 NC
3 +TH1
-TH4 20
-LED4 18
NC 16
NC 6
-TH1 4
-LED1 2
-LED3 12
-LED2 8
-TH3 14
-TH2 10
(*1)
(*1)
(*1)
(*1)
(*2)
(*2)
(*2)
(*2)
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 12
4.2.1.2 Setup with BLE Communication
1. Start "BLExLED" by tapping icon in android tablet. (In advance, set on Bluetooth in Android OS)
Set some attributes in the application. (Device Name #0)
2. Connect AC plug to AC power supply.
3. Tap "Connect" button in "HOME" tab. If connection succeeds, "BLE Connection SUCCESS!" is indicated in the display.
4. Refer to 4.3 Function of Application and operate.
Starting App Setting of the Attribute (In Setting Page)
Connecting to BLE Module with BLE Communication
Return to “HOME” tab
Cypress Demo
Cypress Demo1
Cypress Demo
Cypress Demo
Cypress Demo 1
Cypress Demo
Cypress Demo 1
"Cypress Demo"← Check
Cypress Demo
Cypress Demo 1
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 13
4.3 Function of Application
4.3.1 "SEEKBER" Tab
4.3.2 "TABLE" Tab
It is possible to change the brightness of each LED by swiping level of seek bar.
When releasing a finger, brightness of LED changes.
Maximum supply power of AC/DC module is 10.8W.Total maximum Output power
is over 10W.
When lighting White LED, make the lighting level of RGB LED "0".
When lighting RGB LED, make the lighting level of White LED "0".
It's possible to change the brightness of the White LED by swiping level of White Seek
bar.
It's possible to change color brightness of the RGB LED by swiping level of Strength
Seek bar.
It's possible to change the color of LED by tapping color table.
When Strength Seek bar level is "0", RGB LED goes out.
Maximum supply power of AC/DC module is 10.8W.Total maximum Output power is
over 10W.
When lighting White LED, make the lighting level of RGB LED "0".
When lighting RGB LED, make the lighting level of White LED "0".
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 14
4.3.3 "SCENE" Tab
4.3.4 "SENSOR" Tab
"Preset Lighting" is operated by this table.
Reading: Bright white lighting
Dinner: Warm white lighting
CYPRESS: Cypress blue color
ALERT: Switching white and red (Sequence per second)
Wakeup: gradually brighter (5 seconds sequence)
Rainbow: Automatic color control
Stop: Stop sequence of "ALERT", "Wake up" and "Rainbow".
It's possible to set a sensor setting and dimming curve at this table.
Dimming curve type select "Linear" or "Log"
It's possible to change the brightness of the white LED by swiping level of white
seek bar.
Fade Time: Setting of fade time
When installing a sensor, below is used. (*1)
Motion: Motion sensor on/off, stand-by detection time select "10sec" or "5min"
Illuminance: Illuminance sensor on/off (*2)
Common: It's used for setting change. The following item can be chosen by a
pulldown.
QUERYS: S6Al211A94 memory reading command (*3)
MEMSET: S6Al211A94 memory writing in command (*3)
BLEGET: BLE module memory reading command (*4)
BLESET: BLE module memory writing in command (*4)
*1: Refer to 4.3.4.1. Example of Sensor Use
*2: When using a motion sensor, illumination sensor can not be used.
*3: Refer to 4.3.4.2. S6Al211A94 Control Command
*4: Refer to 4.3.4.3. BLE Module Control Command
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 15
4.3.4.1 Example of Sensor Use
When using the sensor function of the application, prepare the outside sensor parts.
The recommended parts are as follows.
Figure 4-4 Example of Sensor Use
4.3.4.2 S6Al211A94 Control Command
QUERYS: "1st argument: read address" is input, and "Send" button is pushed.
Data or "TRUE" or "FALSE" of memory is indicated.
MEMSET: "1st argument: write address" and "2nd argument: write data" is input, and "Send" button is pushed.
"OK" is indicated.
Note: Refer to hardware manual of S6AL211A94 for details of the address and write data.
Ex: QUERYS Ex: MEMSET
GND
Vdd
OUT
6.5 kΩ
0.1 μF
Ex: NJL7502L
JRC
E
C
S6AL211A94
48:VO
39:SENSE3/ADD3
40:SENSE4/ADD4 MS_IN
MS_3V
MS_GND
LSm
LSp
LSg
C065
R076
R061
C067
Evaluation board 3V
Illuminance Sensor
0.1 μF
Motion Sensor
Ex: EKMB130111
Panasonic
Read address
Write address
Write data
Read data
Data transmission completion
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 16
4.3.4.3 BLE Module Control Command
Table 4-2 BLEGET Command
Command
1st
Argument
Address
2nd
Argument
Data
Function
Response
Initial Value
BLEGET
00
00
Turning on the lights threshold reading of
illumination sensor
HH LL<CR><LF>
(*1)
00 02
01
Turning off the lights threshold reading of
illumination sensor
00 08
01
-
Reply interval time reading of illumination
sensor
HH LL<CR><LF>
(*2)
00 05
Table 4-3 BLESET Command
Comman
d
1st
Argument
Address
2nd
Argument
Address/Dat
a
3rd
Argument
Data
4th
Argument
Data
Function
Response
BLESET
00
00
HH (*1)
LL (*1)
Turning on the lights threshold writing of
illumination sensor
OK<CR><LF
>
01
Turning off the lights threshold writing of
illumination sensor
01
HH (*2)
LL (*2)
-
Reply interval time writing of illumination
sensor
OK<CR><LF
>
*1: Threshold (hexadecimal number). HH: Upper 2bit data, LL: Lower 8bit data
Only lower rank 2bit is effective for HH data.
Set Turning on the lights threshold smaller than Turning off the lights threshold.
*2: Reply interval time (hexadecimal number). HH: Upper 2bit data, LL: Lower 8bit data
Unit: 0.1 ms, Setting area: 0.1 ms to 6553.5 ms
Ex: BLEGET Ex: BLESET
Read address
Write address
Write data
Read data
Data transmission completion
Setup and Verification
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 17
4.4 How to Do When LED Lighting can not be Controlled.
1. Pull out AC plug
2. Exit "BLExLED" application
3. Turn off Bluetooth indicator in Android OS.
4. Turn on Bluetooth indicator in Android OS.
5. Connect AC plug to electrical outlet.
6. Start "BLExLED". (Continue as above-mentioned)
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 18
5. Layout
5.1 Component Layout
Figure 5-1 Evaluation Board Component Layout
Board size of 10W LED driver: 58mm x 93mm
Layer1 (Top View)
Layer4 (Top View)
Layout
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 19
5.2 Wiring Layout
Figure 5-2 Evaluation Board Wiring Layout
Layer 1 (Top View)
Layer 2 (Top View)
Layer 3 (Top View)
Layer 4 (Top View)
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 20
6. Circuit Schematic
Figure 6-1 Evaluation Board Circuit Schematic
Circuit Schematic
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 21
Figure 6-2 Evaluation Board Circuit Schematic
Circuit Schematic
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 22
Figure 6-3 Evaluation Board Circuit Schematic
CH1
CH2
CH4
CH3
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 23
7. Component List
Table 7-1 Evaluation Board Component List
No.
Component
Parts Number
Vendor
Value
Rated
Voltage(V)
Rated
Current(A)
Remarks
1
C001
C2012X5R1V106K125AC
TDK
10 μF
35
-
-
2
C002
C1608X5R1V475K
TDK
4.7 μF
35
-
-
3
C003
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
-
4
C004
C1608X5R1V475K
TDK
4.7 μF
35
-
-
5
C005
C1608X5R1V475K
TDK
4.7 μF
35
-
-
6
C006
C1608CH1H101J
TDK
100 pF
50
-
-
7
C007
C1608CH1H101J
TDK
100 pF
50
-
-
8
C009
EKMG350ELL471MJ16S
NIPPON-CHEMI-CON
470 μF
35
-
-
9
C061
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
-
10
C065
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
NMT
11
C067
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
-
12
C068
C1608CH1H010C
TDK
1 pF
50
-
-
13
C069
C1608CH1H010C
TDK
1 pF
50
-
-
14
C101-1
C3216X5R1V475K160AB
TDK
4.7 μF
35
-
-
15
C102-1
C3225X5R1H106K
TDK
10 μF
50
-
-
16
C102-3
C1608CH1H102J
TDK
0.001 μF
50
-
NMT
17
C120
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
NMT
18
C201-1
C3216X5R1V475K160AB
TDK
4.7 μF
35
-
-
19
C202-1
C3225X5R1H106K
TDK
10 μF
50
-
-
20
C202-3
C1608CH1H102J
TDK
0.001 μF
50
-
NMT
21
C220
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
NMT
22
C301-1
C3216X5R1V475K160AB
TDK
4.7 μF
35
-
-
23
C302-1
C3225X5R1H106K
TDK
10 μF
50
-
-
24
C302-3
C1608CH1H102J
TDK
0.001 μF
50
-
NMT
25
C320
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
NMT
26
C401-1
C3216X5R1V475K160AB
TDK
4.7 μF
35
-
-
27
C402-1
C3225X5R1H106K
TDK
10 μF
50
-
-
28
C402-3
C1608CH1H102J
TDK
0.001 μF
50
-
NMT
29
C420
C1608X5R1H104K080AA
TDK
0.1 μF
50
-
NMT
30
CN009
M20-9981045
Harwin Inc
210 pin
-
3
-
Component List
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 24
No.
Component
Parts Number
Vendor
Value
Rated
Voltage(V)
Rated
Current(A)
Remarks
31
CN061
TSW-104-14-L-S
Samtec
-
550
7.6
-
32
CN062
FTSH-105-01-F-D-K-ND
Samtec
-
-
-
NMT
33
CN_AC
ML-2100-2P
SATOPARTS
-
300
7
-
34
D101
SS23
FAIRCHILD
-
30
2
-
35
D201
SS23
FAIRCHILD
-
30
2
-
36
D301
SS23
FAIRCHILD
-
30
2
-
37
D401
SS23
FAIRCHILD
-
30
2
-
38
F001
RK73Z1J
KOA
0Ω
-
1
-
39
L101
CLF10040T-221M
TDK
220 μH
-
700 m
-
40
L201
CLF10040T-221M
TDK
220 μH
-
700 m
-
41
L301
CLF10040T-221M
TDK
220 μH
-
700 m
-
42
L401
CLF10040T-221M
TDK
220 μH
-
700 m
-
43
LED001
OSHR1608C1A
OptoSupply
-
-
30 m
NMT
44
M001
S6AL211A94
Cypress
-
-
-
-
45
M011
TUHS10F24
COSEL
24 V
-
-
-
46
M061
MBH7BTZ02
FUJITSU
-
-
-
-
47
Q101
FDC658AP
FAIRCHILD
-
30
4
-
48
Q102
FDC8886
FAIRCHILD
-
30
6.5
-
49
Q201
FDC658AP
FAIRCHILD
-
30
4
-
50
Q202
FDC8886
FAIRCHILD
-
30
6.5
-
51
Q301
FDC658AP
FAIRCHILD
-
30
4
-
52
Q302
FDC8886
FAIRCHILD
-
30
6.5
-
53
Q401
FDC658AP
FAIRCHILD
-
30
4
-
54
Q402
FDC8886
FAIRCHILD
-
30
6.5
-
55
R003
RR0816P-104-D
SSM
100 kΩ
-
-
-
56
R004
RR0816P-123-D
SSM
12 kΩ
-
-
NMT
57
R072
RR0816P-101-D
SSM
100Ω
-
-
-
58
R076
RR0816P-274-D
SSM
270 kΩ
-
-
-
59
R101
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
-
60
R102
RK73H1JTTD1R00F
KOA
1Ω
-
-
-
61
R103
RK73Z1J
KOA
0Ω
-
1
-
62
R104
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
63
R106
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
64
R107
RK73Z1J
KOA
0Ω
-
1
-
65
R120
RR0816P-752-D
SSM
7.5 kΩ
-
-
-
66
R201
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
-
67
R202
RK73H1JTTD3R90F
KOA
3.9Ω
-
-
-
68
R203
RK73Z1J
KOA
0Ω
-
1
-
69
R204
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
70
R206
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
71
R207
RK73Z1J
KOA
0Ω
-
1
-
72
R220
RR0816P-752-D
SSM
7.5 kΩ
-
-
-
73
R301
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
-
74
R302
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
-
Component List
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 25
No.
Component
Parts Number
Vendor
Value
Rated
Voltage(V)
Rated
Current(A)
Remarks
75
R303
RK73Z1J
KOA
0Ω
-
1
-
76
R304
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
77
R306
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
78
R307
RK73Z1J
KOA
0Ω
-
1
-
79
R320
RR0816P-752-D
SSM
7.5 kΩ
-
-
-
80
R401
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
-
81
R402
RK73H1JTTD2R20F
KOA
2.2Ω
-
-
NMT
82
R403
RK73Z1J
KOA
0Ω
-
1
-
83
R404
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
84
R406
RK73H1JTTD1004F
KOA
1 MΩ
-
-
NMT
85
R407
RK73Z1J
KOA
0Ω
-
1
-
86
R420
RR0816P-752-D
SSM
7.5 kΩ
-
-
-
87
R421
RK73Z1J
KOA
0Ω
-
1
-
88
SW062
SKRPACE010
ALPS
-
-
50 m
-
89
X061
ABS10-32r768kHz
ABRACON
32.768
kHz
-
-
-
TDK
:
TDK Corporation
NIPPON-CHEMI-CON
:
Nippon Chemi-Con Corporation
Harwin Inc
:
Harwin Inc
Samtec
:
Samtec, Inc.
SATOPARTS
:
SATO PARTS CO.,LTD
FAIRCHILD
:
Fairchild Semiconductor International, Inc.
KOA
:
KOA Corporation
SSM
:
Susumu Co., Ltd
OptoSupply
:
OptoSupply Limited
Cypress
:
Cypress Semiconductor Corp
COSEL
:
COSEL CO., LTD.
FUJITSU
:
FUJITSU COMPONENT LIMITED
ALPS
:
Alps Electric Co., Ltd.
ABRACON
:
Abracon Corporation
NMT: No mount.
These components are compliant with RoHS, and please ask each vendor for details if necessary.
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 26
8. Property Data
Figure 8-1 Switching Waveform
CH1 100% Dimming
CH2 100% Dimming
VINAC =100VRMS, ILEDout(W) = 290 mA
LED: LUW CR7P (5 series + 10Ω)
ACTUAL LEVEL = 255(Line)
CH1: LED current (ILEDout(W)), 100 mA/div
CH2: LEDp voltage (VLEDout(W)), 2V/div
CH3: Switching node voltage(W), 5V/div
VINAC =100VRMS, ILEDout(R) = 140 mA
LED: LR CP7P (5 series + 10Ω)
ACTUAL LEVEL = 255(Line)
CH1: LED current (ILEDout(R)), 50 mA/div
CH2: LEDp voltage (VLEDout(R)), 2V/div
CH3: Switching node voltage(R), 5V/div
CH3 100% Dimming
CH4 100% Dimming
VINAC =100VRMS, ILEDout(G) = 180 mA
LED: LT CP7P (5 series + 10Ω)
ACTUAL LEVEL = 255(Line)
CH1: LED current (ILEDout(G)), 50 mA/div
CH2: LEDp voltage (VLEDout(G)), 2V/div
CH3: Switching node voltage(G), 5V/div
VINAC =100VRMS, ILEDout(B) = 90 mA
LED: LB CP7P (5 series + 10Ω)
ACTUAL LEVEL = 255(Line)
CH1: LED current (ILEDout(B)), 20 mA/div
CH2: LEDp voltage (VLEDout(B)), 2V/div
CH3: Switching node voltage(B), 5V/div
Property Data
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 27
Figure 8-2 Switching Waveform
CH1 10% Dimming
CH2 10% Dimming
VINAC =100VRMS, ILEDout(W) = 29 mA
LED: LUW CR7P (5 series + 10Ω)
ACTUAL LEVEL = 26(Line)
CH1: LED current (ILEDout(W)), 10 mA/div
CH2: LEDp voltage (VLEDout(W)), 2V/div
CH3: Switching node voltage(W), 5V/div
VINAC =100VRMS, ILEDout(R) = 14 mA
LED: LR CP7P (5 series + 10Ω)
ACTUAL LEVEL = 26(Line)
CH1: LED current (ILEDout(R)), 5 mA/div
CH2: LEDp voltage (VLEDout(R)), 2V/div
CH3: Switching node voltage(R), 5V/div
CH3 10% Dimming
CH4 10% Dimming
VINAC =100VRMS, ILEDout(G) = 18 mA
LED: LT CP7P (5 series + 10Ω)
ACTUAL LEVEL = 26(Line)
CH1: LED current (ILEDout(G)), 5 mA/div
CH2: LEDp voltage (VLEDout(G)), 2V/div
CH3: Switching node voltage(G), 5V/div
VINAC =100VRMS, ILEDout(B) = 9 mA
LED: LB CP7P (5 series + 10Ω)
ACTUAL LEVEL = 26(Line)
CH1: LED current (ILEDout(B)), 2 mA/div
CH2: LEDp voltage (VLEDout(B)), 2V/div
CH3: Switching node voltage(B), 5V/div
Property Data
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 28
Figure 8-3 Switching Waveform
CH1 1% Dimming
CH2 1% Dimming
VINAC =100VRMS, ILEDout(W) = 2.9 mA
LED: LUW CR7P (5 series + 10Ω)
ACTUAL LEVEL = 2(Line)
CH1: LED current (ILEDout(W)), 1 mA/div
CH2: LEDp voltage (VLEDout(W)), 2V/div
CH3: Switching node voltage(W), 5V/div
VINAC =100VRMS, ILEDout(R) = 1.4 mA
LED: LR CP7P (5 series + 10Ω)
ACTUAL LEVEL = 2(Line)
CH1: LED current (ILEDout(R)), 1 mA/div
CH2: LEDp voltage (VLEDout(R)), 2V/div
CH3: Switching node voltage(R), 5V/div
CH3 1% Dimming
CH4 1% Dimming
VINAC =100VRMS, ILEDout(G) = 1.8 mA
LED: LT CP7P (5 series + 10Ω)
ACTUAL LEVEL = 2(Line)
CH1: LED current (ILEDout(G)), 1 mA/div
CH2: LEDp voltage (VLEDout(G)), 2V/div
CH3: Switching node voltage(G), 5V/div
VINAC =100VRMS, ILEDout(B) = 0.9 mA
LED: LB CP7P (5 series + 10Ω)
ACTUAL LEVEL = 2(Line)
CH1: LED current (ILEDout(B)), 1 mA/div
CH2: LEDp voltage (VLEDout(B)), 2V/div
CH3: Switching node voltage(B), 5V/div
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 29
9. Board Picture
Figure 9-1 Evaluation Board Picture
(Top View)
(Bottom View)
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 30
10. Ordering Information
Table 10-1 Ordering Information
Part Number
EVB Revision
Note
S6SAL211A94SA1001
S6SAL211A94-BLE-SA1 Rev3.0
-
S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide, Document Number: 002-08727 Rev. *B 31
Revision History
Document Title: S6SAL211A94SA1001 4ch 10W LED Driver Board Operation Guide
Document Number: 002-08727
Revision
Issue Date
Origin of
Change
Description of Change
**
06/12/2015
HSAT
Initial release
*A
04/25/2016
HSAT
Migrated Spansion Guide from S6SAL211A94SA1001_SS901-00039-1v0-E,to Cypress format
*B
06/03/2019
ATTS
Udpated template
