Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 1 of 13 North America only
FEATURES:
Models
Single output
Model
Max
Output
Power
(W) *
Output
Voltage
Range (V)
Output
Current
(A)
Input Voltage
(VAC/Hz)
Input Voltage
(VDC)
Efficiency
(%)
AMEOR60-50120AZ
60
36-50
1.2
90-277/47-440
130-390
89
AMEOR60-36170AZ
59.8
24-36
1.66
90-277/47-440
130-390
88
AMEOR60-24250AZ
60
12-24
2.5
90-277/47-440
130-390
87
AMEOR60-12500AZ
60
5-12
5
90-277/47-440
130-390
85
*Exceeding the maximum output power will permanently damage the converter
All models can be ordered with optional North American colour input wires (black (L), white (N), green (GND)). Add “–NA” to part number
when ordering.
NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25°C,
humidity<75%, nominal input voltage (115/230/277VAC) and at rated output load unless otherwise specified. See
http://www.aimtec.com/terms-sale
AMEOR60-AZ’s AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with
the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are
prone to ‘dirty’ electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or
cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge
suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations
prior to installation may damage sensitive equipment permanently.
Input Specifications
Parameters
Conditions
Typical
Maximum
Units
Inrush current <2ms
115VAC
30
A
230VAC
50
Leakage current
115VAC
0.5
mA
230VAC
0.75
AC current
115VAC
0.67
A
230VAC
0.33
Power Factor
115VAC
0.99
230VAC
0.97
External fuse
250V/1.5A
Start up time
250
ms
Surge voltage
2sec
440
V
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Current accuracy
±3
%
Line regulation
LL-HL
±1
%
Load regulation
0-100% load
±3
%
Ripple & Noise *
20MHz Bandwidth
75
mV p-p
Hold-up time
90
ms
Current adjustment range
100-0
%
Minimum Load Voltage
See the models table
• AC-DC Constant current LED Driver
• Over Temperature Protection
• Input range 90-277VAC/47-440Hz
• Open frame
• High Efficiency up to 89%
• Power Factor Correction
• Operating temperature -40 to 80°C
• Dimmable via analog / 0-10Vdc / PWM
(C version see table)
• SCP, Over Current Protection
• 5 Years Limited Warranty
Click on Series name for product info on aimtec.com
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 2 of 13 North America only
* Tested with 0.1µF (M/C) or (C/C) and 10µF (E/C) parallel capacitors at the end.
Isolation Specifications
Parameters
Conditions
Typical
Rated
Units
Tested I/O voltage
3 sec/3.5mA
3000
VAC
Isolation Resistance
>1000
MΩ
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
130
KHz
Over current protection
AMEOR60-50120AZ
1.27
A
AMEOR60-36170AZ
1.77
AMEOR60-24250AZ
2.55
AMEOR60-12500AZ
5.2
Over voltage protection
Refer to Constant Current vs. Constant Voltage Mode curve
Short circuit protection
Continuous
Short circuit restart
Auto recovery
Over temperature protection
>105°C
Operating temperature
With derating over 60°C
-40 to +80
oC
Maximum case temperature
100
oC
Storage temperature
-40 to +95
oC
Temperature coefficient
±0.02
% / oC
Cooling
Free air convection
Humidity
95
% RH
Wires
UL1015 18AWG * 20CM
Weight
220
g
Dimensions (L X H X W)
5.83 x 1.97 x 1.3 inches 148 x 50 x 33 mm
MTBF
>400,000 hrs (MIL-HDBK-217F at +25°C)
Environment Approval
Test
Parameters
Conditions
Shock
Wave form
Half sine wave
Acceleration amplitude
5gn
Bump duration
30 ms
Converter operation
Before and after test, body mounted (on chassis)
Number of bumps
18 (3 in each direction for every axis)
Vibration
Test mode
Sweep sine, 10-100Hz, speed 0.05Hz/s
Displacement
1 mm
Acceleration
3g, 3 loops 30min one cycle, 3h total, every axis tested
Converter operation
Before and after test, body mounted (on chassis)
Safety Specifications
Parameters
Agency approvals
CE
Standards
Designed to meet UL8750, IEC/EN 60950-1 standards, EN55022, class B
Information Technology Equipment
EN55022 Class B
Harmonic Current Emissions
IEC/EN 61000-3-2, Class C
Voltage fluctuations and flicker
IEC/EN 61000-3-3, (EN60555-3)
Electrostatic Discharge Immunity
IEC 61000-4-2 Level 3
RF, Electromagnetic Field Immunity
IEC 61000-4-3 Level 2
Electrical Fast Transient / Burst Immunity
IEC 61000-4-4 Level 2
Surge Immunity
IEC 61000-4-5 Level 3
RF, Conducted Disturbance Immunity
IEC 61000-4-6 Level 2
Power frequency Magnetic Field Immunity
IEC 61000-4-8 Level 1
Voltage dips, Short Interruptions Immunity
IEC 61000-4-11
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 3 of 13 North America only
Dimensions
NOTE: to adjust the output current connect a 20K Ohm pot between blue and white wire
Wire connection:
AMEOR60-AZ Analog (resistive) Dimming Application Circuit
Model Number
Maximum Pot
Value (kΩ)
AMEPR60-50120AZ
26.00
AMEPR60-36170AZ
16.95
AMEPR60-24250AZ
26.10
AMEPR60-12500AZ
34.10
Wire
Connection
Brown
AC L
Blue
AC N
Green
Ground
Red
+V output
Black
-V Output
Blue (Dimming)
+ Vs dimming
White (Dimming)
-Vs dimming
148.00
(5.83)
Top View
Side View
28.00
(1.10)
50.00
(1.97)
5.00
(0.20)
4.50
(0.18)
4.50
(0.18)
4 Mounting Holes-M3
139.00
(5.47)
41.00
(1.61)
200.00
(8.00)
200.00
(8.00)
Input/Output Wires are 18 AWG 20cm
AMEPR60-AZ
N
1st LED
+Vout
1
1
-Vout
RED
BLACK
AC
BLUE
L
BROWN
GREEN
BLUE
WHITE Pot
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 4 of 13 North America only
AMEOR60-AZ Analog (0-10V) Dimming Application Circuit
AMEOR60-AZ PWM (1KHz) Dimming Application Circuit
Temperature graph
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 5 of 13 North America only
-40 -20 020 40 60 80 100
100
80
60
40
20
0
Safe Operating Area
Output Power (%)
85
Ambient Temperature º C
Free Air Convection
30
60º
C
Efficiency Vs. Input Voltage & Output Current (Constant current load)
AMEOR60-50120AZ
AMEOR60-36170AZ
110Vac, 0.24,
81.4
110Vac, 1.2,
87.9
230Vac, 0.24,
74.0
230Vac, 1.2,
88.0
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 6 of 13 North America only
110Vac, 0.34,
81.4
110Vac, 1.7,
87.9
230Vac, 0.34,
74.6
230Vac, 1.7,
88.0
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 7 of 13 North America only
Efficiency Vs. Input Voltage & Output Current (Constant current load)
Continued
AMEOR60-24250AZ
AMEOR60-12500AZ
110Vac, 0.5,
81.7
110Vac, 2.5,
85.4
230Vac, 0.5,
78.1
230Vac, 2.5,
87.0
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
110Vac, 1,
73.4
110Vac, 5,
83.9
230Vac, 1,
72.9
230Vac, 5,
84.9
(%)
(A)
Efficiency Vs. Input Voltage & Output Current
110Vac
230Vac
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 8 of 13 North America only
PFC Value vs. Output Load Current (constant current mode)
AMEOR60-50120AZ
AMEOR60-36170AZ
115VAC, 50%,
0.98
115VAC,
100%, 1.00
230VAC, 50%,
0.91
230VAC,
100%, 0.96
(load)
(value) PFC value Vs. Output Load Current
115VAC
230VAC
115VAC, 50%,
0.98
115VAC,
100%, 0.99
230VAC, 50%,
0.88
230VAC,
100%, 0.96
(load)
(value) PFC value Vs. Output Load Current
115VAC
230VAC
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 9 of 13 North America only
PFC Value vs. Output Load Current (constant current mode)
Continued
AMEOR60-24250AZ
AMEOR60-12500AZ
115VAC, 50%,
0.98 115VAC,
100%, 1.00
230VAC, 50%,
0.77
230VAC,
100%, 0.94
(load)
(value) PFC value Vs. Output Load Current
115VAC
230VAC
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 10 of 13 North America only
Constant Current vs. Constant Voltage Mode
AMEOR60-50120AZ
AMEOR60-36170AZ
Normal Input,
36, 1.21
Normal Input,
50, 1.22
Normal Input,
50.4, 0.00
Normal Input,
52, 0.00
(V)
(A)Constant Current Vs. Constant Voltage
36
38
40
Normal Input,
24, 1.71
Normal Input,
36, 1.73
Normal Input,
36.4, 0.00
Normal Input,
38, 0.00
(V)
(A)Constant Current Vs. Constant Voltage
24
26
28
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 11 of 13 North America only
Constant Current vs. Constant Voltage Mode
Continued
AMEOR60-24250AZ
AMEOR60-12500AZ
Normal Input,
12, 2.51
Normal Input,
24, 2.53
Normal Input,
24.5, 0.00
Normal Input,
26, 0.00
(V)
(A)Constant Current Vs. Constant Voltage
12
14
16
Normal Input,
5, 5.04
Normal Input,
12, 5.02
Normal Input,
12.3, 0.00
Normal Input,
14, 0.00
(V)
(A)Constant Current Vs. Constant Voltage
5
6
7
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 12 of 13 North America only
Dimming Control (Output Current vs. Radj)
AMEOR60-50120AZ
AMEOR60-36170AZ
Normal Input,
0.007, 0%
Normal Input,
0.01 , 10%
Normal Input,
0.02 , 20%
Normal Input,
0.10 , 30%
Normal Input,
0.15 , 40%
Normal Input,
0.25 , 50%
Normal Input,
0.45 , 60%
Normal Input,
0.88 , 70%
Normal Input,
1.50 , 80%
Normal Input,
4.26 , 90%
Normal Input,
26.00 , 100%
K(Ω)
(A) Output Current vs. Resistance adjustment
0.007
0.01
Normal Input,
0, 0%
Normal Input,
0.06 , 10%
Normal Input,
0.12 , 20%
Normal Input,
0.19 , 30%
Normal Input,
0.29 , 40%
Normal Input,
0.43 , 50%
Normal Input,
0.63 , 60%
Normal Input,
0.96 , 70%
Normal Input,
1.58 , 80%
Normal Input,
3.05 , 90%
Normal Input,
16.95 , 100%
K(Ω)
(A) Output Current vs. Resistance adjustment
0
0.06
Series AMEOR60-AZ
up to 5A | AC-DC / DC-DC LED driver
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC
(924 6832)
F 052.1e R3.L 13 of 13 North America only
Constant Current vs. Constant Voltage Mode
Continued
AMEOR60-24250AZ
AMEOR60-12500AZ
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
Normal Input,
0, 0%
Normal Input,
0.00 , 10%
Normal Input,
0.00 , 20%
Normal Input,
0.00 , 30%
Normal Input,
0.11 , 40%
Normal Input,
0.35 , 50%
Normal Input,
0.50 , 60%
Normal Input,
0.88 , 70%
Normal Input,
1.84 , 80%
Normal Input,
4.29 , 90%
Normal Input,
26.10 , 100%
K(Ω)
(A) Output Current vs. Resistance adjustment
0
0.00
Normal Input,
0, 0%
Normal Input,
0.00 , 10%
Normal Input,
0.00 , 20%
Normal Input,
0.01 , 30%
Normal Input,
0.03 , 40%
Normal Input,
0.06 , 50%
Normal Input,
0.30 , 60%
Normal Input,
0.60 , 70%
Normal Input,
1.54 , 80%
Normal Input,
3.74 , 90%
Normal Input,
34.10 , 100%
K(Ω)
(A) Output Current vs. Resistance adjustment
0
0.00
