Caution: Observe precautions when handling because these devices are sensitive to electrostatic discharge
L-BAND SPDT SWITCH
GaAs INTEGRATED CIRCUIT
PG2012TK
Document No. PG10219EJ01V0DS (1st edition)
Date Published December 2002 CP(K)
DESCRIPTION
The
PG2012TK is a GaAs MMIC for L-band SPDT (Single Pole Double Throw) switch which were developed for
mobile phone and another L-band application.
This device can operate frequency from 0.5 GHz to 2.5 GHz, having the low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold package (1511). And this package is able to high-density
surface mounting.
FEATURES
Supply voltage : VDD = 2.7 to 3.0 V (2.8 V TYP.)
Switch control voltage : Vcont (H) = 2.7 to 3.0 V (2.8 V TYP.)
: Vcont (L) = 0.2 to +0.2 V (0 V TYP.)
Low insertion loss : LINS1 = 0.27 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
: LINS2 = 0.30 dB TYP. @ f = 2.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
: LINS3 = 0.30 dB TYP. @ f = 2.5 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V (Reference
value)
High isolation : ISL1 = 30 dB TYP. @ f = 0.5 to 2.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
: ISL2 = 30 dB TYP. @ f = 2.5 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V (Reference
value)
High-density surface mounting : 6-pin lead-less minimold package (1.5 1.1 0.55 mm)
APPLICATIONS
L-band digital cellular or cordless telephone
PCS, W-LAN, WLL and BluetoothTM etc.
ORDERING INFORMATION
Part Number
Package
Marking
Supplying Form
PG2012TK-E2
6-pin lead-less minimold
(1511)
G3H
Embossed tape 8 mm wide
Pin 1, 6 face the perforation side of the tape
Qty 5 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order:
PG2012TK-A
Data Sheet PG10219EJ01V0DS
2
PG2012TK
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
OUTPUT1
2
GND
3
OUTPUT2
4
Vcont
5
INPUT
6
VDD
TRUTH TABLE
Vcont
INPUTOUTPUT1
INPUTOUTPUT2
Low
OFF
ON
High
ON
OFF
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Parameter
Symbol
Ratings
Unit
Supply Voltage
VDD
+6.0
V
Switch Control Voltage
Vcont
+6.0
V
Input Power
Pin
+26
dBm
Power Dissipation
PD
150 Note
mW
Operating Ambient Temperature
TA
45 to +85
C
Storage Temperature
Tstg
55 to +150
C
Note Mounted on double-sided copper-clad 50 50 1.6 mm epoxy glass PWB, TA = +85C
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Supply Voltage
VDD
2.7
2.8
3.0
V
Switch Control Voltage (H)
Vcont(H)
2.7
2.8
3.0
V
Switch Control Voltage (L)
Vcont(L)
0.2
0
0.2
V
Data Sheet PG10219EJ01V0DS
3
PG2012TK
ELECTRICAL CHARACTERISTICS
(TA = +25C, VDD = 2.8 V, Vcont = 2.8 V/0 V, DC cut capacitors = 56 pF, unless otherwise specified)
Parameter
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Insertion Loss1
LINS1
f = 0.5 to 1.0 GHz
0.27
0.50
dB
Insertion Loss2
LINS2
f = 2.0 GHz
0.30
0.50
dB
Isolation1
ISL1
f = 0.5 to 2.0 GHz
24
30
dB
Input Return Loss
RLin
f = 0.5 to 2.5 GHz
15
20
dB
Output Return Loss
RLout
f = 0.5 to 2.5 GHz
15
20
dB
0.1 dB Gain Compression
Input Power Note
Pin(0.1 dB)
f = 2.0 GHz
+17.5
+20.5
dBm
Supply Current
IDD
50
100
A
Switching Control Current
Icont
4
20
A
Note Pin(0.1dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear
range.
STANDARD CHARACTERISTICS FOR REFERENCE
(TA = +25C, VDD = 2.8 V,Vcont = 2.8 V/0 V, DC cut capacitors = 56 pF, unless otherwise specified)
Parameter
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Insertion Loss3
LINS3
f = 2.5 GHz
0.30
dB
Isolation2
ISL2
f = 2.5 GHz
30
dB
1 dB Gain Compression
Input Power Note
Pin(1 dB)
f = 2.0 GHz
+24.0
dBm
Switching Control Speed
tSW
300
ns
Note Pin(1dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear
range.
Caution This device is used it is necessary to use DC cut capacitors. The value of DC cut capacitors
should be chosen to accommodate the frequency of operation, bandwidth, switching speed and
the condition with actual board of your system. The range of recommended DC cut capacitor
value is less than 100 pF.
Data Sheet PG10219EJ01V0DS
4
PG2012TK
EVALUATION CIRCUIT (VDD = 2.8 V, Vcont = 2.8 V/0 V, DC cut capacitors = 56 pF)
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
Data Sheet PG10219EJ01V0DS
5
PG2012TK
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
USING THE EVALUATION BOARD
Symbol
Values
C1, C2, C3
56 pF
C4, C5
1 000 pF
Data Sheet PG10219EJ01V0DS
6
PG2012TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm)
Remark ( ): Reference value
Data Sheet PG10219EJ01V0DS
7
PG2012TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Soldering Conditions
Condition Symbol
Infrared Reflow
Peak temperature (package surface temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220C or higher : 60 seconds or less
Preheating time at 120 to 180C : 12030 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
VPS
Peak temperature (package surface temperature) : 215C or below
Time at temperature of 200C or higher : 25 to 40 seconds
Preheating time at 120 to 150C : 30 to 60 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
VP215
Wave Soldering
Peak temperature (molten solder temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Preheating temperature (package surface temperature) : 120C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating
Peak temperature (pin temperature) : 350C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
8 Data Sheet PG10219EJ01V0DS
PG2012TK
SAFETY INFORMATION ON THIS PRODUCT
Caution GaAs Products
The product contains gallium arsenide, GaAs.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
Do not destroy or burn the product.
Do not cut or cleave off any part of the product.
Do not crush or chemically dissolve the product.
Do not put the product in the mouth.
Follow related laws and ordinances for disposal. The product should be excluded from general
industrial waste or household garbage.