T4 Series (R) 4A TRIACS SNUBBERLESSTM & LOGIC LEVEL Table 1: Main Features A2 Symbol Value Unit IT(RMS) 4 A VDRM/VRRM 600 to 800 V IGT (Q1) 5 to 35 mA G A1 A2 A2 A1 A2 G DESCRIPTION Based on ST's Snubberless / Logic level technology providing high commutation performances, the T4 series is suitable for use on AC inductive loads. They are recommended for applications using universal motors, electrovalves.... such as kitchen aid equipments, power tools, dishwashers,... Available in a fully insulated package, the T4......W version complies with UL standards (ref. E81734). A1 A2 G DPAK (T4-B) IPAK (T4-H) A2 A1 A2 G TO-220AB (T4-T) Table 2: Order Codes Part Number T405-xxxB T405-xxxB-TR T405-xxxH T405-xxxT T405-xxxW T410-xxxB T410-xxxB-TR T410-xxxH T4105-xxxT T410-xxxW T435-xxxB T435-xxxB-TR T435-xxxH T435-xxxT T435-xxxW January 2006 REV. 7 A1 A2 G ISOWATT220AB (T4-W) Marking See page table 8 on page 9 1/10 T4 Series Table 3: Absolute Maximum Ratings Symbol IT(RMS) ITSM Parameter IPAK/DPAK/ TO-220AB RMS on-state current (full sine wave) Non repetitive surge peak on-state F = 50 Hz current (full cycle, Tj initial = 25C) F = 60 Hz tp = 10 ms dI/dt Critical rate of rise of on-state current IG = 2 x IGT , tr 100 ns F = 120 Hz IGM Peak gate current tp = 20 s PG(AV) Tstg Tj Unit 4 A ISOWATT220AB Tc = 105C It Value for fusing It Tc = 110C Value Average gate power dissipation t = 20 ms 30 t = 16.7 ms 31 A 5.1 A s Tj = 125C 50 A/s Tj = 125C 4 A Tj = 125C 1 W - 40 to + 150 - 40 to + 125 C Storage junction temperature range Operating junction temperature range Tables 4: Electrical Characteristics (Tj = 25C, unless otherwise specified) Symbol IGT (1) VGT Test Conditions VD = 12 V RL = 30 VGD VD = VDRM RL = 3.3 k Tj = 125C IH (2) IT = 100 mA IL IG = 1.2 IGT dV/dt (2) (dI/dt)c (2) (dV/dt)c = 10 V/s Tj = 125C Tj = 125C Note 1: minimum IGT is guaranted at 5% of IGT max. Note 2: for both polarities of A2 referenced to A1. 2/10 T435 5 10 35 Unit I - II - III MAX. 1.3 V I - II - III MIN. 0.2 V II Tj = 125C T410 MAX. I - III (dV/dt)c = 0.1 V/s T405 I - II - III MAX. VD = 67 %VDRM gate open Tj = 125C Without snubber T4 Quadrant MAX. MIN. MIN. 10 15 35 10 25 50 15 30 60 20 40 400 1.8 2.7 - 0.9 2.0 - - - 2.5 mA mA mA V/s A/ms T4 Series Table 5: Static Characteristics Symbol Test Conditions VT (2) ITM = 5.5 A Vto (2) tp = 380 s Value Unit Tj = 25C MAX. 1.56 V Threshold voltage Tj = 125C MAX. 0.89 V Rd (2) Dynamic resistance Tj = 125C MAX. 120 m IDRM IRRM VDRM = VRRM 5 A 1 mA Tj = 25C Tj = 125C MAX. Note 1: minimum IGT is guaranted at 5% of IGT max. Note 2: for both polarities of A2 referenced to A1. Table 6: Thermal resistance Symbol Rth(j-c) Parameter Junction to case (AC) S = 0.5 cm Rth(j-a) Junction to ambient Value IPAK / DPAK / TO-220AB 2.6 ISOWATT220AB 4.0 DPAK 70 TO-220AB / ISOWATT220AB 60 IPAK 100 Unit C/W C/W S = Copper surface under tab. 3/10 T4 Series Figure 1: Maximum power dissipation versus RMS on-state current (full cycle) Figure 2: RMS on-state current versus case temperature (full cycle) P(W) IT(RMS)(A) 4.5 6 4.0 5 TO-220AB / DPAK / IPAK 3.5 3.0 4 ISOWATT220AB 2.5 3 2.0 1.5 2 1.0 1 0.5 IT(RMS)(A) TC(C) 0.0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0 4.0 Figure 3: RMS on-state current versus ambient temperature (printed circuit board FR4, copper thickness: 35m) (full cycle) 25 50 75 100 125 Figure 4: Relative variation of thermal impedance versus pulse duration IT(RMS)(A) K=[Zth/Rth] 2.0 1E+0 1.8 Rth(j-c) DPAK (S=0.5CM2) 1.6 ISOWATT220AB Rth(j-a) 1.4 1.2 TO-220AB / DPAK / IPAK 1.0 1E-1 TO-220AB / ISOWATT220AB 0.8 DPAK / IPAK 0.6 0.4 0.2 tp(s) TC(C) 0.0 0 25 50 1E-2 75 100 1E-2 125 Figure 5: On-state characteristics (maximum values) 1E-1 1E+0 1E+1 1E+2 5E+2 Figure 6: Surge peak on-state current versus number of cycles ITM(A) ITSM(A) 30.0 35 Tj max. Vto = 0.90V Rd = 120 m 10.0 30 t=20ms 25 One cycle 20 Non repetitive Tj initial=25C Tj = Tj max. 15 1.0 Tj = 25C. Repetitive TC=110C 10 5 VTM(V) Number of cycles 0 0.1 0.0 4/10 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1 10 100 1000 T4 Series Figure 7: Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms and corresponding value of I2t 2 Figure 8: Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25C] 2 ITSM(A), I t (A s) 2.5 500 Tj initial=25C 2.0 dI/dt limitation: 50A/s 100 IGT ITSM 1.5 IH & IL 1.0 10 I2t 0.5 Tj(C) tp(ms) 0.0 1 0.01 0.10 1.00 -40 10.00 Figure 9: Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) -20 0 20 40 60 80 100 120 140 Figure 10: Relative variation of critical rate of decrease of main current versus junction temperature (dI/dt)c [Tj] / (dI/dt)c [Tj specified] (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 6 2.4 2.2 5 2.0 1.8 4 1.6 1.4 1.2 3 T435 1.0 0.8 2 T410 0.6 T405 0.4 1 0.2 (dV/dt)c (V/s) Tj(C) 0.0 0 0.1 1.0 10.0 100.0 0 25 50 75 100 125 Figure 11: DPAK thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 m) Rth(j-a)(C/W) 100 90 80 70 60 50 40 30 20 10 S(cm) 0 0 4 8 12 16 20 24 28 32 36 40 5/10 T4 Series Figure 12: Ordering Information Scheme T 4 05 - 600 B (-TR) Triac series Current 4 = 4A Sensitivity 05 = 5mA 10 = 10mA 35 = 35mA Voltage 600 = 600V 700 = 700V 800 = 800V Package B = DPAK H = IPAK T = TO-220AB W = ISOWATT220AB Packing mode Blank = Tube -TR = Tape & reel Table 7: Product Selector Part Number T405-xxxB T405-xxxH T405-xxxT T405-xxxW T410-xxxB T410-xxxH T410-xxxT T410-xxxW T435-xxxB T435-xxxH T435-xxxT T435-xxxW 6/10 600 V X X X X X X X X X X X X Voltage (xxx) 700 V 800 V X X X X X X X X X X X X X X X X X X X X X X X X Sensitivity 5 mA 5 mA 5 mA 5 mA 10 mA 10 mA 10 mA 10 mA 35 mA 35 mA 35 mA 35 mA Type Package Logic level DPAK Logic level IPAK Logic level TO-220AB Logic level ISOWATT220AB Logic level DPAK Logic Level IPAK Logic Level TO-220AB Logic Level ISOWATT220AB Snubberless DPAK Snubberless IPAK Snubberless TO-220AB Snubberless ISOWATT220AB T4 Series Figure 13: DPAK Package Mechanical Data DIMENSIONS REF. E A B2 C2 L2 D R H L4 A1 B R G C A2 0.60 MIN. Inches Min. Max Min. Max. A 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.018 0.023 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.251 0.259 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.397 L2 V2 Millimeters 0.80 typ. 0.031 typ. L4 0.60 1.00 0.023 0.039 V2 0 8 0 8 Figure 14: DPAK Foot Print Dimensions (in millimeters) 6.7 3 3 1.6 2.3 6.7 2.3 1.6 7/10 T4 Series Figure 15: ISOWATT220AB Package Mechanical Data DIMENSIONS REF. Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 B 2.50 2.70 0.098 0.106 D 2.50 2.75 0.098 0.108 E 0.40 0.70 0.016 0.028 F 0.75 1.00 0.030 0.039 F1 1.15 1.70 0.045 0.067 F2 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.40 2.70 0.094 0.106 H 10.00 10.40 0.394 0.409 L2 16.00 typ. 0.630 typ. L3 28.60 30.60 1.125 1.205 L4 9.80 10.60 0.386 0.417 L6 15.90 16.40 0.626 0.646 L7 9.00 9.30 0.354 0.366 Diam 3.00 3.20 0.118 0.126 Figure 16: IPAK Package Mechanical Data REF. A E C2 B2 L2 D H L B3 L1 B A1 V1 B5 e G 8/10 C A3 A A1 A3 B B2 B3 B5 C C2 D E e G H L L1 L2 V1 DIMENSIONS Millimeters Inches Min. Typ. Max. Min. Typ. 2.20 2.40 0.086 0.90 1.10 0.035 0.70 1.30 0.027 0.64 0.90 0.025 5.20 5.40 0.204 0.95 0.30 0.035 0.45 0.60 0.017 0.48 0.60 0.019 6 6.20 0.236 6.40 6.60 0.252 2.28 0.090 4.40 4.60 0.173 16.10 0.634 9 9.40 0.354 0.8 1.20 0.031 0.80 1 0.031 10 10 Max. 0.094 0.043 0.051 0.035 0.212 0.037 0.023 0.023 0.244 0.260 0.181 0.370 0.047 0.039 T4 Series Figure 17: TO-220AB Package Mechanical Data REF. C B OI b2 L F A I4 l3 c2 a1 l2 a2 M c1 b1 e A a1 a2 B b1 b2 C c1 c2 e F OI I4 L l2 l3 M DIMENSIONS Millimeters Inches Min. Typ. Max. Min. Typ. 15.20 15.90 0.598 3.75 0.147 13.00 14.00 0.511 10.00 10.40 0.393 0.61 0.88 0.024 1.23 1.32 0.048 4.40 4.60 0.173 0.49 0.70 0.019 2.40 2.72 0.094 2.40 2.70 0.094 6.20 6.60 0.244 3.75 3.85 0.147 15.80 16.40 16.80 0.622 0.646 2.65 2.95 0.104 1.14 1.70 0.044 1.14 1.70 0.044 2.60 0.102 Max. 0.625 0.551 0.409 0.034 0.051 0.181 0.027 0.107 0.106 0.259 0.151 0.661 0.116 0.066 0.066 Table 8: Ordering Information Ordering type Marking Package Weight Base qty Delivery mode T4xx-yyyB T4 xxyy DPAK 0.3 g 75 Tube T4xx-yyyB-TR T4 xxyy DPAK 0.3 g 2500 Tape & reel T4xx-yyyH T4 xxyy IPAK 0.4 g 75 Tube T4xx-yyyT T4xx yyyT TO-220AB 2.3 g 50 Tube T4xx-yyyB T4xxyyyW ISOWATT220AB 2.1 g 50 Tube Note: xxx = voltage, yy = sensitivity Table 9: Revision History Date Revision Description of Changes Jun-2003 5 Last update. 25-Mar-2005 6 Layout update. No content change. 25-Jan-2005 7 Markings changed in Table 8 9/10 T4 Series Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10