CRA04S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 24-Feb-2019 1Document Number: 31043
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Thick Film Chip Resistor Array
The CRA04S thick film resistor array is constructed on a
high grade ceramic body with convex terminations. A small
package enables the design of high density circuits. The
single component reduces board space, component
counts, and assembly costs.
FEATURES
• Convex terminal array with square corners
• Wide ohmic range: 10R to 1M0
• 4 or 8 terminal package with isolated resistors
• AEC-Q200 qualified
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Notes
(1) Rated voltage:
(2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rate dissipation applies only if the permitted film temperature of 155 °C is not exceeded
Notes
(1) Preferred way for ordering products is by use of the PART NUMBER
(2) Please refer to the table PACKAGING, see next page
STANDARD ELECTRICAL SPECIFICATIONS
MODEL CIRCUIT
POWER RATING
P70 °C
W
LIMITING ELEMENT
VOLTAGE MAX.
V
TEMPERATURE
COEFFICIENT
± ppm/K
TOLERANCE
± %
RESISTANCE
RANGE
E-SERIES
CRA04S 03 0.063 50 100 1 10 to 1M 24 + 96
200 2; 5 24
Zero-Ohm-Resistor: Rmax. 50 m, Imax. = 1 A
TECHNICAL SPECIFICATIONS
PARAMETER UNIT CRA04S
Rated dissipation at 70 °C (2) W per element 0.063
Limiting element voltage (1) V50
Insulation voltage (1 min) VDC/AC peak 100
Category temperature range °C -55 to +155
Insulation resistance > 109
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRA04S08347K0JTD (1)
MODEL TERMINAL STYLE PIN CIRCUIT VALUE TOLERANCE PACKAGING (2) SPECIAL
CRA04 S 04
08
3 = 03 R = decimal
K = thousand
M = million
0000 = 0 jumper
F = ± 1 %
G = ± 2 %
J = ± 5 %
Z = 0 jumper
TD
TC
PZ
Up to 2 digits
Product Description: CRA04S 08 03 473 J RT7 e3
CRA04S 08 03 473 J RT7 e3
MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE TOLERANCE PACKAGING (4) LEAD (Pb)-FREE
CRA04S 04
08
03 473 = 47 k
4702 = 47 k
10R0 = 10
100 = 10
000 = 0 jumper
F = ± 1 %
G = ± 2 %
J = ± 5 %
Z = 0 jumper
RT7
RT6
PZ
e3 = pure tin
termination finish
First two digits (3 for 1 %)
are significant. Last digit
is the multiplier.
P x R
A04S 8340CR JDK0T7
CRA04S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 24-Feb-2019 2Document Number: 31043
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CIRCUIT DERATING
DIMENSIONS
The dimensions shown are for a 8 pin part. For parts with
different pin numbers use the same pitch and add or
subtract pads as required.
PACKAGING
MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL
PACKAGING CODE
PAPER TAPE
PART NUMBER PRODUCT DESCRIPTION
CRA04S 8 mm
180 mm/7" 2 mm 10 000 TD RT7
330 mm/13" 2 mm 20 000 TC RT6
330 mm/13" 2 mm 50 000 PZ PZ
03 CIRCUIT
4 pin 8 pin
- 55 - 25 0 25 50 75 100 125 155 175
120
100
80
60
40
20
0
70 Ambient Temperature in °C
Rated Power in %
ae
e
PIN
NO #
DIMENSIONS
in millimeters
LAA
1
BB*P
NOM.
TW
4
1.0
± 0.1 - 0.33 0.15 0.25 0.65 0.35 1.0
8
2.0
± 0.2 0.30 0.4 0.15 0.25 0.50 0.45 1.0
TOL.
- ± 0.15 ± 0.15 ± 0.10 ± 0.1 - ± 0.1 ± 0.15
SOLDER PAD DIMENSIONS in millimeters
cwdabe
WAVE 0.45 1.45 0.2 0.4 0.5 0.3
CRA04S
www.vishay.com Vishay
End of Life - Last Available Purchase Date: 31-Dec-2019
Revison: 24-Feb-2019 3Document Number: 31043
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
(1) Figures are given for a single element
(2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
TEST
(clause) CONDITIONS OF TEST
REQUIREMENTS
PERMISSIBLE CHANGE (R/R) (1)
STABILITY
CLASS 1 OR BETTER
STABILITY
CLASS 2 OR BETTER
Stability for product types: 10 to 1 M10 to 1 M
CRA04S
Resistance (4.5) - ± 1 % ± 2 %; ± 5 %
Temperature coefficient (4.8.4.2) (20 / -55 / 20) °C and
(20 / 125 / 20) °C ± 100 ppm/K ± 200 ppm/K
Overload (4.13) U = 2.5 x (P70 x R)1/2
2 x Umax.; 0.5 s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Solderability (4.17.5) (2)
Aging 4 h at 155 °C, dry heat
solder bath method; 235 °C; 2 s
visual examination
Good tinning ( 95 % covered)
no visible damage
Resistance to soldering heat (4.18.2) Solder bath method;
(260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Rapid change of temperature (4.19) 30 min at LCT = -55 °C;
30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
Damp heat, steady state (4.24) (40 ± 2) °C; 56 days;
(93 ± 3) % RH ± (1 % R + 0.05 )± (2 % R + 0.1 )
Climatic sequence (4.23)
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = -55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
U = (P70 x R)1/2
U = Umax.; whichever is less severe
± (1 % R + 0.05 )± (2 % R + 0.1 )
Endurance at 70 °C (4.25.1)
U = (P70 x R)1/2
U = Umax.; whichever is less severe
1.5 h “ON”; 0.5 h “OFF”;
70 °C; 1000 h
± (1 % R + 0.05 )± (2 % R + 0.1 )
Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )
Endurance at upper category
temperature (4.25.3) UCT = 125 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Generic specification
Sectional specification
Detail specification
Variety of environmental test procedures
Packaging of SMD components
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
