CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY 1 Mbit (128K x 8) Serial SPI nvSRAM Features 1 Mbit Nonvolatile SRAM Internally organized as 128K x 8 STORE to QuantumTrap nonvolatile elements initiated automatically on power down (AutoStore) or by user using HSB pin (Hardware Store) or SPI instruction (Software Store) RECALL to SRAM initiated on power up (Power Up Recall) or by SPI Instruction (Software RECALL) Automatic STORE on power down with a small capacitor High Reliability Infinite Read, Write, and RECALLl cycles 200,000 STORE cycles to QuantumTrap Data Retention: 20 Years Low Power Consumption Single 3V +20%, -10% operation Average VCC current of 10 mA at 40 MHz operation Industry Standard Configurations Commercial and industrial temperatures CY14B101Q1 has identical pin configuration to industry standard 8-pin NV Memory 8-pin DFN and 16-pin SOIC Packages RoHS compliant Functional Overview High Speed Serial Peripheral Interface (SPI) 40 MHz Clock rate Supports SPI Modes 0 (0,0) and 3 (1,1) Write Protection Hardware Protection using Write Protect (WP) Pin Software Protection using Write Disable Instruction Software Block Protection for 1/4,1/2, or entire Array The Cypress CY14B101Q1/CY14B101Q2/CY14B101Q3 combines a 1 Mbit nonvolatile static RAM with a nonvolatile element in each memory cell. The memory is organized as 128K words of 8 bits each. The embedded nonvolatile elements incorporate the QuantumTrap technology, creating the world's most reliable nonvolatile memory. The SRAM provides infinite read and write cycles, while the QuantumTrap cell provides highly reliable nonvolatile storage of data. Data transfers from SRAM to the nonvolatile elements (STORE operation) takes place automatically at power down. On power up, data is restored to the SRAM from the nonvolatile memory (RECALL operation). Both STORE and RECALL operations can also be triggered by the user. Logic Block Diagram CS WP SCK VCC Quantum Trap 128K X 8 Instruction decode Write protect Control logic STORE SRAM ARRAY HOLD RECALL 128K X 8 Instruction register Address Decoder VCAP Power Control STORE/RECALL Control HSB D0-D7 A0-A16 SI Data I/O register SO Status register Cypress Semiconductor Corporation Document #: 001-50091 Rev. *B * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised July 02, 2009 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Pinouts Figure 1. Pin Diagram - 8-Pin DFN[1, 3, 2] CS SO WP GND 1 CY14B101Q1 2 Top View 3 not to scale 4 8 VCC CS 7 HOLD SO 6 SCK 5 SI VCAP GND 1 CY14B101Q2 2 Top View 3 not to scale 4 8 VCC 7 HOLD 6 SCK 5 SI Figure 2. Pin Diagram - 16-Pin SOIC NC 1 16 VCC NC 2 15 NC NC 3 14 VCAP 13 SO 12 SI SCK CY14B101Q3 NC 4 WP 5 HOLD 6 11 7 10 8 9 NC GND Top View not to scale CS HSB Table 1. Pin Definitions Pin Name I/O Type Description CS Input Chip Select. Activates the device when pulled LOW. Driving this pin high puts the device in low power standby mode. SCK Input Serial Clock. Runs at speeds up to max 40 MHz. All inputs are latched at the rising edge of this clock. Outputs are driven at the falling edge of the clock. SI Input Serial Input. Pin for input of all SPI instructions and data. SO Output WP Input Serial Output. Pin for output of data through SPI. Write Protect. Implements hardware write protection in SPI. HOLD Input HOLD Pin. Suspends Serial Operation. HSB Input/Output Hardware STORE Busy: A weak internal pull up keeps this pin pulled high. If not used, this pin is left as No Connect. Output: Indicates busy status of nvSRAM when LOW. Input: Hardware STORE implemented by pulling this pin LOW externally. VCAP Power Supply AutoStore Capacitor. Supplies power to the nvSRAM during power loss to STORE data from the SRAM to nonvolatile elements. If AutoStore is not needed, this pin must be left as No Connect. It must never be connected to GND. NC No Connect No Connect: This pin is not connected to the die. GND Power Supply Ground VCC Power Supply Power Supply (2.7 to 3.6V) Notes 1. HSB pin is not available in 8 DFN packages. 2. CY14B101Q1 part does not have VCAP pin and does not support AutoStore. 3. CY14B101Q2 part does not have WP pin Document #: 001-50091 Rev. *B Page 2 of 22 [+] Feedback PRELIMINARY CY14B101Q1 CY14B101Q2 CY14B101Q3 Device Operation SRAM Write CY14B101Q1/CY14B101Q2/CY14B101Q3 is 1 Mbit nvSRAM memory with a nonvolatile element in each memory cell. All the reads and writes to nvSRAM happen to the SRAM which gives nvSRAM the unique capability to handle infinite writes to the memory. The data in SRAM is secured by a STORE sequence which transfers the data in parallel to the nonvolatile Quantum Trap cells. A small capacitor (VCAP) is used to AutoStore the SRAM data in nonvolatile cells when power goes down providing power down data security. The Quantum Trap nonvolatile elements built in the reliable SONOS technology make nvSRAM the ideal choice for secure data storage. All writes to nvSRAM are carried out on the SRAM and do not use up any endurance cycles of the nonvolatile memory. This enables user to perform infinite write operations. A Write cycle is performed through the SPI WRITE instruction. The WRITE instruction is issued through the SI pin of the nvSRAM and consists of the WRITE opcode, three bytes of address, and one byte of data. Write to nvSRAM is done at SPI bus speed with zero cycle delay. The 1 Mbit memory array is organized as 128K words x 8 bits. The memory can be accessed through a standard SPI interface that enables very high clock speeds upto 40 MHz with zero cycle delay read and write cycles. This device supports SPI modes 0 and 3 (CPOL, CPHA = 0, 0 and 1, 1) and operates as SPI slave. The device is enabled using the Chip Select pin (CS) and accessed through Serial Input (SI), Serial Output (SO), and Serial Clock (SCK) pins. This device provides the feature for hardware and software write protection through WP pin and WRDI instruction respectively along with mechanisms for block write protection (1/4, 1/2, or full array) using BP0 and BP1 pins in the status register. Further, the HOLD pin can be used to suspend any serial communication without resetting the serial sequence. CY14B101Q1/CY14B101Q2/CY14B101Q3 uses the standard SPI opcodes for memory access. In addition to the general SPI instructions for read and write, it provides four special instructions which enable access to four nvSRAM specific functions: STORE, RECALL, AutoStore Disable (ASDISB), and AutoStore Enable (ASENB). The major benefit of nvSRAM SPI over serial EEPROMs is that all reads and writes to nvSRAM are performed at the speed of SPI bus with zero delay. Therefore, no wait time is required after any of the memory accesses. The STORE and RECALL operations need finite time to complete and all memory accesses are inhibited during this time. While a STORE or RECALL operation is in progress, the busy status of the device is indicated by the Hardware STORE Busy (HSB) pin and also reflected on the RDY bit of the Status Register. The Device is available in three different pin configurations that enable the user to choose a part which fits in best in their application. The feature summary is given in Table 2. Table 2. Feature Summary Feature CY14B101Q1 CY14B101Q2 CY14B101Q3 WP Yes No Yes VCAP No Yes Yes HSB No No Yes AutoStore No Yes Yes Power Up RECALL Yes Yes Yes Hardware STORE No No Yes Software STORE Yes Yes Yes Document #: 001-50091 Rev. *B The device allows burst mode writes to be performed through SPI. This enables write operations on consecutive addresses without issuing a new WRITE instruction. When the last address in memory is reached, the address rolls over to 0x0000 and the device continues to write. The SPI write cycle sequence is defined explicitly in the Memory Access section of SPI Protocol Description. SRAM Read A read cycle is performed at the SPI bus speed and the data is read out with zero cycle delay after the READ instruction is performed. The READ instruction is issued through the SI pin of the nvSRAM and consists of the READ opcode and 3 bytes of address. The data is read out on the SO pin. This device allows burst mode reads to be performed through SPI. This enables reads on consecutive addresses without issuing a new READ instruction. When the last address in memory is reached in burst mode read, the address rolls over to 0x0000 and the device continues to read. The SPI read cycle sequence is defined explicitly in the Memory Access section of SPI Protocol Description. STORE Operation STORE operation transfers the data from the SRAM to the nonvolatile Quantum Trap cells. The device stores data to the nonvolatile cells using one of three STORE operations: AutoStore, activated on device power down; Software STORE, activated by a STORE instruction in the SPI; Hardware STORE, activated by the HSB. During the STORE cycle, an erase of the previous nonvolatile data is first performed, followed by a program of the nonvolatile elements. After a STORE cycle is initiated, further input and output are disabled until the cycle is completed. The HSB signal or the RDY bit in the Status register can be monitored by the system to detect if a STORE cycle is in progress. The busy status of nvSRAM is indicated by HSB being pulled LOW or RDY bit being set to `1'. To avoid unnecessary nonvolatile STOREs, AutoStore and Hardware STORE operations are ignored unless at least one write operation has taken place since the most recent STORE or RECALL cycle. Software initiated STORE cycles are performed regardless of whether a write operation has taken place. Page 3 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY The AutoStore operation is a unique feature of nvSRAM which automatically stores the SRAM data to QuantumTrap during power down. This Store mechanism is implemented using a capacitor (VCAP) and enables the device to safely STORE the data in the nonvolatile memory when power goes down. During normal operation, the device draws current from VCC to charge the capacitor connected to the VCAP pin. When the voltage on the VCC pin drops below VSWITCH during power down, the device inhibits all memory accesses to nvSRAM and automatically performs a conditional STORE operation using the charge from the VCAP capacitor. The AutoStore operation is not initiated if no write cycle has been performed since last RECALL. Note If a capacitor is not connected to VCAP pin, Autostore must be disabled by issuing the AutoStore Disable instruction specified in AutoStore Disable (ASDISB) on page 12. If AutoStore is enabled without a capacitor on VCAP pin, the device will attempt an AutoStore operation without sufficient charge to complete the Store. This may corrupt the data stored in nvSRAM and Status register. In such case, WRSR instruction needs to be issued to update the non-volatile bits BP0, BP1, WPEN to resume normal functionality. The HSB pin also acts as an open drain driver that is internally driven LOW to indicate a busy condition, when a STORE cycle (initiated by any means) or Power up RECALL is in progress. Upon completion of the STORE operation, the nvSRAM remains disabled until the HSB pin returns HIGH. Leave the HSB pin unconnected if not used. Note CY14B101Q1/CY14B101Q2 do not have HSB pin. RDY bit of the SPI status register may be probed to determine the Ready or Busy status of nvSRAM Figure 3. AutoStore Mode Vcc 0.1uF 10kOhm AutoStore Operation Vcc CS VSS During power down, the memory accesses are inhibited after the voltage on VCC pin drops below VSWITCH. To avoid inadvertent writes, it must be ensured that CS is not left floating prior to this event. Therefore, during power down the device must be deselected and CS must be allowed to follow VCC. Figure 3 shows the proper connection of the storage capacitor (VCAP) for AutoStore operation. Refer to DC Electrical Characteristics on page 13 for the size of the VCAP. Note CY14B101Q1 does not support AutoStore operation. The user must perform Software STORE operation by using the SPI STORE instruction to secure the data. Software Store Operation Software STORE enables the user to trigger a STORE operation through a special SPI instruction. This operation is initiated irrespective of whether a write has been performed since last nv operation. A STORE cycle takes tSTORE to complete, during which all the memory accesses to nvSRAM are inhibited. The RDY bit of the Status register or the HSB pin may be polled to find the Ready or Busy status of the nvSRAM. After the tSTORE cycle time is completed, the SRAM is activated again for read and write operations. Hardware STORE and HSB pin Operation The HSB pin in CY14B101Q3 is used to control and acknowledge STORE operations. If no STORE or RECALL is in progress, this pin can be used to request a Hardware STORE cycle. When the HSB pin is driven LOW, nvSRAM conditionally initiates a STORE operation after tDELAY duration. An actual STORE cycle starts only if a write to the SRAM has been performed since the last STORE or RECALL cycle. Reads and Writes to the memory are inhibited for tSTORE duration or as long as HSB pin is LOW. Document #: 001-50091 Rev. *B VCAP VCAP RECALL Operation A RECALL operation transfers the data stored in the nonvolatile Quantum Trap elements to the SRAM. A RECALL may be initiated in two ways: Hardware RECALL, initiated on power up; and Software RECALL, initiated by a SPI RECALL instruction. Internally, RECALL is a two-step procedure. First, the SRAM data is cleared. Next, the nonvolatile information is transferred into the SRAM cells. All memory accesses are inhibited while a RECALL cycle is in progress. The RECALL operation does not alter the data in the nonvolatile elements. Hardware Recall (Power Up) During power up, when VCC crosses VSWITCH, an automatic RECALL sequence is initiated which transfers the content of nonvolatile memory on to the SRAM. The data would previously have been stored on the nonvolatile memory through a STORE sequence. A Power Up Recall cycle takes tFA time to complete and the memory access is disabled during this time. HSB pin can be used to detect the Ready status of the device. user Software RECALL Software RECALL enables the user to initiate a RECALL operation to restore the content of nonvolatile memory on to the SRAM. A Software RECALL is issued by using the SPI instruction for RECALL. A Software RECALL takes tRECALL to complete during which all memory accesses to nvSRAM are inhibited. The controller must provide sufficient delay for the RECALL operation to complete before issuing any memory access instructions. Page 4 of 22 [+] Feedback PRELIMINARY CY14B101Q1 CY14B101Q2 CY14B101Q3 Disabling and Enabling AutoStore Chip Select (CS) If the application does not require the AutoStore feature, it can be disabled by using the ASDISB instruction. If this is done, the nvSRAM does not perform a STORE operation at power down. For selecting any slave device, the master needs to pull down the corresponding CS pin. Any instruction can be issued to a slave device only while the CS pin is LOW. When the device is not selected, data through the SI pin is ignored and the serial output pin (SO) remains in a high impedance state. AutoStore can be re-enabled by using the ASENB instruction. However, these operations are not nonvolatile and if the user needs this setting to survive power cycle, a STORE operation must be performed following Autostore Disable or Enable operation. Note A new instruction must begin with the falling edge of Chip Select (CS). Therefore, only one opcode can be issued for each active Chip Select cycle. Note CY14B101Q2/CY14B101Q3 has AutoStore Enabled from the factory. In CY14B101Q1, VCAP pin is not present and AutoStore option is not available. The Autostore Enable and Disable instructions to CY14B101Q1 are ignored. Serial Clock (SCK) Note If AutoStore is disabled and VCAP is not required, leave it open. VCAP pin must never be connected to GND. Power Up Recall operation cannot be disabled in any case. CY14B101Q1/CY14B101Q2/CY14B101Q3 enables SPI modes 0 and 3 for data communication. In both these modes, the inputs are latched by the slave device on the rising edge of SCK and outputs are issued on the falling edge. Therefore, the first rising edge of SCK signifies the arrival of first bit (MSB) of SPI instruction on the SI pin. Further, all data inputs and outputs are synchronized with SCK. Serial Peripheral Interface SPI Overview The SPI is a four-pin interface with Chip Select (CS), Serial Input (SI), Serial Output (SO) and Serial Clock (SCK) pins. CY14B101Q1/CY14B101Q2/CY14B101Q3 provides serial access to nvSRAM through SPI interface. The SPI bus on this device can run at speeds up to 40 MHz The SPI is a synchronous serial interface which uses clock and data pins for memory access and supports multiple devices on the data bus. A device on SPI bus is activated using a chip select pin. The relationship between chip select, clock, and data is dictated by the SPI mode. This device supports SPI modes 0 and 3. In both these modes, data is clocked into nvSRAM on rising edge of SCK starting from the first rising edge after CS goes active. The SPI protocol is controlled by opcodes. These opcodes specify the commands from the bus master to the slave device. After CS is activated the first byte transferred from the bus master is the opcode. Following the opcode, any addresses and data are then transferred. The CS must go inactive after an operation is complete and before a new opcode can be issued. The commonly used terms used in SPI protocol are given below: SPI Master The SPI Master device controls the operations on a SPI bus. An SPI bus may have only one master with one or more slave devices. All the slaves share the same SPI bus lines and master may select any of the slave devices using the Chip Select pin. All the operations must be initiated by the master activating a slave device by pulling the CS pin of the slave LOW. The master also generates the Serial Clock (SCK) and all the data transmission on SI and SO lines are synchronized with this clock. SPI Slave SPI slave device is activated by the master through the Chip Select line. A slave device gets the Serial Clock (SCK) as an input from the SPI master and all the communication is synchronized with this clock. SPI slave never initiates a communication on the SPI bus and acts on the instruction from the master. CY14B101Q1/CY14B101Q2/CY14B101Q3 operates as a SPI slave and may share the SPI bus with other SPI slave devices. Document #: 001-50091 Rev. *B Serial clock is generated by the SPI master and the communication is synchronized with this clock after CS goes LOW. Data Transmission - SI and SO SPI data bus consists of two lines, SI and SO, for serial data communication. The SI is also referred to as MOSI (Master Out Slave In) and SO is referred to as MISO (Master In Slave Out). The master issues instructions to the slave through the SI pin, while the slave responds through the SO pin. Multiple slave devices may share the SI and SO lines as described earlier. Most Significant Bit (MSB) The SPI protocol requires that the first bit to be transmitted is the Most Significant Bit (MSB). This is valid for both address and data transmission. The 1 Mbit serial nvSRAM requires a 3-byte address for any read or write operation. However, since the actual address is only 17 bits, it implies that the first seven bits which are fed in are ignored by the device. Although these seven bits are `don't care', Cypress recommends that these bits are treated as 0s to enable seamless transition to higher memory densities. Serial Opcode After the slave device is selected with CS going LOW, the first byte received is treated as the opcode for the intended operation. CY14B101Q1/CY14B101Q2/CY14B101Q3 uses the standard opcodes for memory accesses. In addition to the memory accesses, it provides additional opcodes for the nvSRAM specific functions: STORE, RECALL, AutoStore Enable, and AutoStore Disable. Refer to Table 3 on page 7 for details. Invalid Opcode If an invalid opcode is received, the opcode is ignored and the device ignores any additional serial data on the SI pin till the next falling edge of CS and the SO pin remains tristated. Status Register CY14B101Q1/CY14B101Q2/CY14B101Q3 has an 8-bit status register. The bits in the status register are used to configure the SPI bus. These bits are described in Table 5 on page 8. Page 5 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Figure 4. System Configuration Using SPI nvSRAM SCK M OSI M IS O SCK SI SO SCK SI SO u C o n tro lle r C Y14B 101Q x CS C Y14B 101Q x HO LD CS HO LD CS1 HO LD 1 CS2 HO LD 2 SPI Modes CY14B101Q1/CY14B101Q2/CY14B101Q3 may be driven by a microcontroller with its SPI peripheral running in either of the following two modes: The two SPI modes are shown in Figure 5 and Figure 6. The status of clock when the bus master is in Standby mode and not transferring data is: SCK remains at 0 for Mode 0 SCK remains at 1 for Mode 3 SPI Mode 0 (CPOL=0, CPHA=0) SPI Mode 3 (CPOL=1, CPHA=1) CPOL and CPHA bits must be set in the SPI controller for either Mode 0 or Mode 3. The device detects the SPI mode from the status of SCK pin when the device is selected by bringing the CS pin LOW. If SCK pin is LOW when device is selected, SPI Mode 0 is assumed and if SCK pin is HIGH, it works in SPI Mode 3. For both these modes, input data is latched-in on the rising edge of Serial Clock (SCK) starting from the first rising edge after CS goes active. If the clock starts from a HIGH state (in mode 3), the first rising edge, after the clock toggles, is considered. The output data is available on the falling edge of Serial Clock (SCK). Figure 6. SPI Mode 3 Figure 5. SPI Mode 0 CS CS 0 1 2 3 4 5 6 1 2 3 4 5 6 7 SCK SCK SI 0 7 7 6 5 4 MSB Document #: 001-50091 Rev. *B 3 2 1 0 LSB SI 7 MSB 6 5 4 3 2 1 0 LSB Page 6 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY SPI Operating Features Active Power and Standby Power Modes Power Up When Chip Select (CS) is LOW, the device is selected, and is in the Active Power mode. The device consumes ICC current, as specified in DC Electrical Characteristics on page 13. When Chip Select (CS) is HIGH, the device is deselected and the device goes into the Standby Power mode if a STORE or RECALL cycle is not in progress. If a STORE or RECALL cycle is in progress, device goes into the Standby Power Mode after the STORE or RECALL cycle is completed. In the Standby Power mode, the current drawn by the device drops to ISB. Power up is defined as the condition when the power supply is turned on and VCC crosses Vswitch voltage. During this time, the Chip Select (CS) must be allowed to follow the VCC voltage. Therefore, CS must be connected to VCC through a suitable pull up resistor. As a built-in safety feature, Chip Select (CS) is both edge sensitive and level sensitive. After power up, the device is not selected until a falling edge is detected on Chip Select (CS). This ensures that Chip Select (CS) must have been HIGH, before going Low to start the first operation. As described earlier, nvSRAM performs a Power Up Recall operation after power up and therefore, all memory accesses are disabled for tRECALL duration after power up. The HSB pin can be probed to check the ready or busy status of nvSRAM after power up. Power On Reset A Power On Reset (POR) circuit is included to prevent inadvertent writes. At power up, the device does not respond to any instruction until the VCC reaches the Power On Reset threshold voltage (VSWITCH). After VCC transitions the POR threshold, the device is internally reset and performs an Power Up Recall operation. The device is in the following state after POR: Deselected (after Power up, a falling edge is required on Chip Select (CS) before any instructions are started). Standby Power mode Not in the Hold Condition Status register state: Write Enable (WEN) bit is reset to 0. WPEN, BP1, BP0 unchanged from previous power down The WPEN, BP1, and BP0 bits of the Status Register are nonvolatile bits and remain unchanged from the previous power down. SPI Functional Description The CY14B101Q1/CY14B101Q2/CY14B101Q3 uses an 8-bit instruction register. Instructions and their opcodes are listed in Table 3. All instructions, addresses, and data are transferred with the MSB first and start with a HIGH to LOW CS transition. There are, in all, 12 SPI instructions which provide access to most of the functions in nvSRAM. Further, the WP and HOLD pins provide additional functionality driven through hardware. Table 3. Instruction Set Instruction Category Status Register Control Instructions Instruction Name Opcode Operation WREN 0000 0110 Set Write Enable Latch WRDI 0000 0100 Reset Write Enable Latch RDSR 0000 0101 Read Status Register WRSR 0000 0001 Write Status Register READ 0000 0011 Read Data From Memory Array WRITE 0000 0010 Write Data To Memory Array STORE 0011 1100 Software STORE RECALL 0110 0000 Before selecting and issuing instructions to the memory, a valid and stable VCC voltage must be applied. This voltage must remain valid until the end of the transmission of the instruction. Power Down At power down (continuous decay of VCC), when VCC drops from the normal operating voltage and below the VSWITCH threshold voltage, the device stops responding to any instruction sent to it. If a write cycle is in progress during power down, it is allowed tDELAY time to complete after Vcc transitions below VSWITCH, after which all memory accesses are inhibited and a conditional AutoStore operation is performed (AutoStore is not performed if no writes have happened since last RECALL cycle). This feature prevents inadvertent writes to nvSRAM from happening during power down. However, to completely avoid the possibility of inadvertent writes during power down, ensure that the device is deselected and is in Standby Power Mode, and the Chip Select (CS) follows the voltage applied on VCC. Document #: 001-50091 Rev. *B SRAM Read/Write Instructions Special NV Instructions Reserved Software RECALL ASENB 0101 1001 AutoStore Enable ASDISB 0001 1001 AutoStore Disable - Reserved - 0001 1110 Reserved for Internal use The SPI instructions are divided based on their functionality in the following types: Status Register Access: WRSR and RDSR instructions Write Protection Functions: WREN and WRDI instructions along with WP pin and WEN, BP0, and BP1 bits SRAM memory Access: READ and WRITE instructions nvSRAM special instructions: STORE, RECALL, ASENB, and ASDISB Page 7 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Status Register The status register bits are listed in Table 3. The status register consists of Ready bit (RDY) and data protection bits BP1, BP0, WEN, and WPEN. The RDY bit can be polled to check the Ready or Busy status while a nvSRAM STORE cycle is in progress. The status register can be modified by WRSR instruction and read by RDSR instruction. However, only WPEN, BP1, and BP0 bits of the Status Register can be modified by using WRSR instruction. WRSR instruction has no effect on WEN and RDY bits. The default value shipped from the factory for BP1, BP2 and WPEN bits is `0'. Table 4. Status Register Format Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WPEN (0) X X X BP1 (0) BP0 (0) WEN RDY Table 5. Status Register Bit Definition Bit Definition Description Bit 0 (RDY) Ready Read Only bit indicates the ready status of device to perform a memory access. This bit is set to "1" by the device while a STORE or Software RECALL cycle is in progress. Bit 1 (WEN) Write Enable WEN indicates if the device is write-enabled. Setting WEN = '1' enables writes and setting WEN = '0' disables all write operations Bit 2 (BP0) Block Protect bit `0' Used for block protection. For details see Table 6 on page 9. Bit 3 (BP1) Block Protect bit `1' Used for block protection. For details see Table 6 on page 9. Bit 7 (WPEN) Write Protect Enable bit Used for enabling the function of Write Protect Pin (WP). For details see Table 7 on page 10. Read Status Register (RDSR) Instruction WRSR instruction is a write instruction and needs writes to be enabled (WEN bit set to `1') using the WREN instruction before it is issued. The instruction is issued after the falling edge of CS using the opcode for WRSR followed by 8 bits of data to be stored in the Status Register. Since, only bits 2, 3, and 7 can be modified by WRSR instruction, it is recommended to leave the other bits as `0' while writing to the Status Register The Read Status Register instruction provides access to the status register. This instruction is used to probe the Write Enable Status of the device or the Ready status of the device. RDY bit is set by the device to 1 whenever a STORE cycle is in progress. The Block Protection and WPEN bits indicate the extent of protection employed. Note In CY14B101Q1/CY14B101Q2/CY14B101Q3, the values written to Status Register are saved to nonvolatile memory only after a STORE operation. If AutoStore is disabled (or while using CY14B101Q1), any modifications to the Status Register must be secured by using a Software STORE operation This instruction is issued after the falling edge of CS using the opcode for RDSR. Write Status Register (WRSR) Instruction The WRSR instruction enables the user to write to the Status register. However, this instruction cannot be used to modify bit 0 and bit 1 (WEN and RDY). The BP0 and BP1 bits can be used to select one of four levels of block protection. Further, WPEN bit can be set to `1' to enable the use of Write Protect (WP) pin. Note CY14B101Q2 does not have WP pin. Any modification to bit 7 of the Status register has no effect on the functionality of CY14B101Q2. Figure 7. Read Status Register (RDSR) Instruction Timing CS 0 1 2 3 4 5 6 7 0 1 0 MSB 1 2 3 4 5 6 7 SCK SI SO 0 0 0 0 HI-Z 0 1 0 D7 D6 D5 D4 D3 D2 D1 D0 MSB Document #: 001-50091 Rev. *B LSB Data LSB Page 8 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Figure 8. Write Status Register (WRSR) Instruction Timing CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Data in Opcode SI 0 0 0 0 0 0 0 1 D7 0 0 0 D3 D2 0 MSB 0 LSB HI-Z SO Write Protection and Block Protection Write Disable (WRDI) Instruction CY14B101Q1/CY14B101Q2/CY14B101Q3 provides features for both software and hardware write protection using WRDI instruction and WP. Additionally, this device also provides block protection mechanism through BP0 and BP1 pins of the Status Register. Write Disable instruction disables the write by clearing the WEN bit to `0' in order to protect the device against inadvertent writes. This instruction is issued following falling edge of CS followed by opcode for WRDI instruction. The WEN bit is cleared on the rising edge of CS following a WRDI instruction. Figure 10. WRDI Instruction The write enable and disable status of the device is indicated by WEN bit of the status register. The write instructions (WRSR and WRITE) and nvSRAM special instruction (STORE, RECALL, ASENB, and ASDISB) need the write to be enabled (WEN bit = 1) before they can be issued. Write Enable (WREN) Instruction On power up, the device is always in the write disable state. The following WRITE, WRSR, or nvSRAM special instruction must therefore be preceded by a Write Enable instruction. If the device is not write enabled (WEN = `0'), it ignores the write instructions and returns to the standby state when CS is brought HIGH. A new CS falling edge is required to re-initiate serial communication. The instruction is issued following the falling edge of CS. When this instruction is used, the WEN bit of status register is set to `1'. WEN bit defaults to `0' on power up. Note After completion of a write instruction (WRSR or WRITE) or nvSRAM special instruction (STORE, RECALL, ASENB, and ASDISB) instruction, WEN bit is cleared to `0'. This is done to provide protection from any inadvertent writes. Therefore, WREN instruction needs to be used before a new write instruction is issued. Figure 9. WREN Instruction CS 1 2 3 4 5 6 0 0 0 0 0 Hi-Z Document #: 001-50091 Rev. *B 1 1 0 1 2 3 4 5 6 7 SCK 0 SI 0 0 0 0 1 0 0 Hi-Z SO Block Protection Block protection is provided using the BP0 and BP1 pins of the Status register. These bits can be set using WRSR instruction and probed using the RDSR instruction. The nvSRAM is divided into four array segments. One-quarter, one-half, or all of the memory segments can be protected. Any data within the protected segment is read only. Table 6 shows the function of Block Protect bits. Table 6. Block Write Protect Bits 7 SCK SO 0 Level 0 SI CS Status Register Bits Array Addresses Protected BP1 BP0 0 0 0 None 1 (1/4) 0 1 0x18000-0x1FFFF 2 (1/2) 1 0 0x10000-0x1FFFF 3 (All) 1 1 0x00000-0x1FFFF Page 9 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Write Protect (WP) Pin followed for a read operation: After the CS line is pulled LOW to select a device, the read opcode is transmitted through the SI line followed by three bytes of address. The Most Significant address byte contains A16 in bit 0 and other bits as `don't cares'. Address bits A15 to A0 are sent in the following two address bytes. After the last address bit is transmitted on the SI pin, the data (D7-D0) at the specific address is shifted out on the SO line on the falling edge of SCK. Any other data on SI line after the last address bit is ignored. The write protect pin (WP) is used to provide hardware write protection. WP pin enables all normal read and write operations when held HIGH. When the WP pin is brought LOW and WPEN bit is "1", all write operations to the status register are inhibited. The hardware write protection function is blocked when the WPEN bit is "0". This enables the user to install the device in a system with the WP pin tied to ground, and still write to the status register. CY14B101Q1/CY14B101Q2/CY14B101Q3 allows reads to be performed in bursts through SPI which can be used to read consecutive addresses without issuing a new READ instruction. If only one byte is to be read, the CS line must be driven HIGH after one byte of data comes out. However, the read sequence may be continued by holding the CS line LOW and the address is automatically incremented and data continues to shift out on SO pin. When the last data memory address (0x1FFFF) is reached, the address rolls over to 0x0000 and the device continues to read. WP pin can be used along with WPEN and Block Protect bits (BP1 and BP0) of the status register to inhibit writes to memory. When WP pin is LOW and WPEN is set to "1", any modifications to status register are disabled. Therefore, the memory is protected by setting the BP0 and BP1 bits and the WP pin inhibits any modification of the status register bits, providing hardware write protection. Note WP going LOW when CS is still LOW has no effect on any of the ongoing write operations to the status register. Note CY14B101Q2 does not have WP pin and therefore does not provide hardware write protection. Write Sequence (WRITE) The write operations on this device are performed through the Serial Input (SI) pin. To perform a write operation, if the device is write disabled, then the device must first be write enabled through the WREN instruction. When the writes are enabled (WEN = `1'), WRITE instruction is issued after the falling edge of CS. A WRITE instruction constitutes transmitting the WRITE opcode on SI line followed by 3 bytes address sequence and the data (D7-D0) which is to be written. The Most Significant address byte contains A16 in bit 0 with other bits being `don't cares'. Address bits A15 to A0 are sent in the following two address bytes. Table 7 summarizes all the protection features of this device Table 7. Write Protection Operation Unprotected WEN Protected Blocks Blocks Status Register WPEN WP X X 0 Protected Protected 0 X 1 Protected Writable Writable 1 LOW 1 Protected Writable Protected 1 HIGH 1 Protected Writable Writable Protected CY14B101Q1/CY14B101Q2/CY14B101Q3 enables writes to be performed in bursts through SPI which can be used to write consecutive addresses without issuing a new WRITE instruction. If only one byte is to be written, the CS line must be driven HIGH after the D0 (LSB of data) is transmitted. However, if more bytes are to be written, CS line must be held LOW and address is incremented automatically. The following bytes on the SI line are treated as data bytes and written in the successive addresses. When the last data memory address (0x1FFFF) is reached, the address rolls over to 0x0000 and the device continues to write. The WEN bit is reset to "0" on completion of a WRITE sequence. Memory Access All memory accesses are done using the READ and WRITE instructions. These instructions cannot be used while a STORE or RECALL cycle is in progress. A STORE cycle in progress is indicated by the RDY bit of the status register and the HSB pin. Read Sequence (READ) The read operations on this device are performed by giving the instruction on Serial Input pin (SI) and reading the output on Serial Output (SO) pin. The following sequence needs to be Figure 11. Read Instruction Timing CS 1 2 3 4 5 6 7 0 1 2 3 4 5 SCK Op-Code SI 0 0 0 0 0 SO Document #: 001-50091 Rev. *B 0 6 7 ~ ~ ~ ~ 0 20 21 22 23 0 1 2 3 4 5 6 7 17-bit Address 1 1 0 0 MSB 0 0 0 0 0 A16 A3 A2 A1 A0 LSB D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB Data Page 10 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Figure 12. Burst Mode Read Instruction Timing CS 2 3 4 5 6 1 0 7 2 3 4 5 6 7 Op-Code 0 0 0 0 1 2 3 4 5 6 7 0 0 7 1 2 3 4 5 6 7 17-bit Address 0 1 0 1 0 0 0 0 0 0 ~ ~ SI 20 21 22 23 0 ~ ~ 1 ~ ~ 0 SCK A16 0 MSB A3 A2 A1 A0 LSB Data Byte N SO ~ ~ Data Byte 1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D0 D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB MSB LSB Figure 13. Write Instruction Timing CS 1 2 3 4 5 0 7 6 1 2 3 4 5 6 7 ~ ~ ~ ~ 0 SCK Op-Code SI 0 0 0 0 0 20 21 22 23 0 1 2 3 4 5 6 7 17-bit Address 0 1 0 0 0 0 0 0 0 A16 0 MSB A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 LSB MSB LSB Data HI-Z SO Figure 14. Burst Mode Write Instruction Timing CS 4 5 6 7 0 1 2 3 4 5 6 Op-Code SI 0 0 0 0 0 7 20 21 22 23 0 1 2 3 4 5 1 0 0 0 MSB 0 0 0 0 0 A16 0 7 0 1 2 3 4 5 6 7 Data Byte N A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D0 D7 D6 D5 D4 D3 D2 D1 D0 SO nvSRAM Special Instructions CY14B101Q1/CY14B101Q2/CY14B101Q3 provides four special instructions which enables access to four nvSRAM specific functions: STORE, RECALL, ASDISB, and ASENB. Table 8 lists these instructions. Software STORE When a STORE instruction is executed, nvSRAM performs a Software STORE operation. The STORE operation is issued irrespective of whether a write has taken place since last STORE or RECALL operation. Document #: 001-50091 Rev. *B 7 Data Byte 1 17-bit Address 0 6 ~ ~ 3 ~ ~ 2 ~ ~ 1 ~ ~ 0 SCK LSB MSB LSB HI-Z Table 8. nvSRAM Special Instructions Function Name STORE RECALL ASENB ASDISB Opcode 0011 1100 0110 0000 0101 1001 0001 1001 Operation Software STORE Software RECALL AutoStore Enable AutoStore Disable To issue this instruction, the device must be write enabled (WEN bit = `1'). The instruction is performed by transmitting the STORE opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the STORE instruction. Page 11 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY AutoStore Enable (ASENB) Figure 15. Software STORE Operation The AutoStore Enable instruction enables the AutoStore on CY14B101Q1. This setting is not nonvolatile and needs to be followed by a STORE sequence to survive the power cycle. CS 0 1 2 3 4 5 6 7 To issue this instruction, the device must be write enabled (WEN = `1'). The instruction is performed by transmitting the ASENB opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the ASENB instruction. SCK 0 SI 0 1 1 1 1 0 0 Hi-Z SO Note If ASDISB and ASENB instructions are executed in CY14B101Q1, the device is busy for the duration of software sequence processing time (tSS). However, ASDISB and ASENB instructions have no effect on CY14B101Q1 as AutoStore is internally disabled. Software RECALL When a RECALL instruction is executed, nvSRAM performs a Software RECALL operation. To issue this instruction, the device must be write enabled (WEN = `1'). The instruction is performed by transmitting the RECALL opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the RECALL instruction. Figure 16. Software RECALL Operation Figure 18. AutoStore Enable Operation CS 0 1 SI 0 1 CS 0 1 2 3 4 5 6 3 4 5 6 7 0 1 1 0 0 1 Hi-Z SO 7 2 SCK SCK 1 1 0 0 0 0 HOLD Pin Operation 0 Hi-Z SO AutoStore Disable (ASDISB) AutoStore is enabled by default in CY14B101Q2/CY14B101Q3. The ASDISB instruction disables the AutoStore. This setting is not nonvolatile and needs to be followed by a STORE sequence to survive the power cycle. To issue this instruction, the device must be write enabled (WEN = `1'). The instruction is performed by transmitting the ASDISB opcode on the SI pin following the falling edge of CS. The WEN bit is cleared on the positive edge of CS following the ASDISB instruction. Figure 17. AutoStore Disable Operation The HOLD pin is used to pause the serial communication. When the device is selected and a serial sequence is underway, HOLD is used to pause the serial communication with the master device without resetting the ongoing serial sequence. To pause, the HOLD pin must be brought LOW when the SCK pin is LOW. To resume serial communication, the HOLD pin must be brought HIGH when the SCK pin is LOW (SCK may toggle during HOLD). While the device serial communication is paused, inputs to the SI pin are ignored and the SO pin is in the high impedance state. This pin can be used by the master with the CS pin to pause the serial communication by bringing the pin HOLD LOW and deselecting an SPI slave to establish communication with another slave device, without the serial communication being reset. The communication may be resumed at a later point by selecting the device and setting the HOLD pin HIGH. Figure 19. HOLD Operation CS CS 0 1 2 3 4 5 6 7 SCK ~ ~ ~ ~ 0 SI SCK SI SO 0 0 0 1 1 0 0 1 HOLD SO Hi-Z Document #: 001-50091 Rev. *B Page 12 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested. Package Power Dissipation Capability (TA = 25C) ................................................... 1.0W Storage Temperature ................................. -65C to +150C Surface Mount Lead Soldering Temperature (3 Seconds) .......................................... +260C Maximum Accumulated Storage Time At 150C Ambient Temperature................... ..... 1000h At 85C Ambient Temperature..................... 20 Years Ambient Temperature with Power Applied ............................................ -55C to +150C Supply Voltage on VCC Relative to GND ........-0.5V to +4.1V DC Voltage Applied to Outputs in High-Z State....................................... -0.5V to VCC + 0.5V Input Voltage.......................................... -0.5V to VCC + 0.5V Transient Voltage (<20 ns) on Any Pin to Ground Potential .................. -2.0V to VCC + 2.0V DC Output Current (1 output at a time, 1s duration).....15 mA Static Discharge Voltage.......................................... > 2001V (per MIL-STD-883, Method 3015) Latch up Current.................................................... > 200 mA Table 9. Operating Range Range Ambient Temperature VCC 0C to +70C 2.7V to 3.6V Commercial Industrial -40C to +85C DC Electrical Characteristics Over the Operating Range (VCC = 2.7V to 3.6V) Parameter Description Test Conditions Min Typ[4] Max Unit 2.7 3.0 3.6 V 10 mA VCC Power Supply Voltage ICC1 Average Vcc Current ICC2 Average VCC Current All Inputs Don't Care, VCC = Max. during STORE Average current for duration tSTORE 10 mA ICC4 Average VCAP Current All Inputs Don't Care, VCC = Max. during AutoStore Average current for duration tSTORE Cycle 5 mA ISB VCC Standby Current CS > (VCC - 0.2V). VIN < 0.2V or > (VCC - 0.2V). Standby current level after nonvolatile cycle is complete. Inputs are static. f = 0 MHz. 5 mA IIX[5] Input Leakage Current VCC = Max, VSS < VIN < VCC (except HSB) -1 +1 A Input Leakage Current VCC = Max, VSS < VIN < VCC (for HSB) -100 +1 A -1 +1 A At fSCK = 40 MHz. Values obtained without output loads (IOUT = 0 mA) IOZ Off State Output Leakage Current VCC = Max, VSS < VOUT < VCC VIH Input HIGH Voltage 2.0 VCC + 0.5 V VIL Input LOW Voltage VSS - 0.5 0.8 V 0.4 V 180 F VOH Output HIGH Voltage IOUT = -2 mA VOL Output LOW Voltage IOUT = 4 mA VCAP Storage Capacitor Between VCAP pin and VSS, 5V Rated 2.4 61 V 68 Notes 4. Typical values are at 25C, VCC= VCC (Typ) . Not 100% tested. 5. The HSB pin has IOUT = -2 uA for VOH of 2.4V when both active high and LOW drivers are disabled. When they are enabled standard VOH and VOL are valid. This parameter is characterized but not tested. Document #: 001-50091 Rev. *B Page 13 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Data Retention and Endurance Parameter Description Min Unit DATAR Data Retention 20 Years NVC Nonvolatile STORE Operations 200 K Max Unit 6 pF 8 pF Capacitance Parameter[6] Description Test Conditions CIN Input Capacitance COUT Output Pin Capacitance TA = 25C, f = 1MHz, VCC = VCC (Typ) Thermal Resistance Parameter [6] Description JA Thermal Resistance (Junction to Ambient) JC Thermal Resistance (Junction to Case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51. 16-SOIC 8-DFN Unit TBD TBD C/W TBD TBD C/W Figure 20. AC Test Loads and Waveforms 577 577 3.0V 3.0V R1 R1 OUTPUT OUTPUT 30 pF R2 789 5 pF R2 789 AC Test Conditions Input Pulse Levels.................................................... 0V to 3V Input Rise and Fall Times (10% - 90%) ....................... <3 ns Input and Output Timing Reference Levels.....................1.5V Note 6. These parameters are guaranteed by design and are not tested. Document #: 001-50091 Rev. *B Page 14 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY AC Switching Characteristics Cypress Parameter Alt. Parameter fSCK tCL tCH tCS tCSS tCSH tSD tHD tHH tSH tCO tHHZ tHLZ tOH tHZCS 40MHz Description fSCK tWL tWH tCE tCES tCEH tSU tH tHD tCD Clock Frequency, SCK Clock Pulse Width Low Clock Pulse Width High CS High Time CS Setup Time CS Hold Time Data In Setup Time Data In Hold Time HOLD Hold Time HOLD Setup Time tV tHZ tLZ tHO tDIS Output Valid HOLD to Output High Z HOLD to Output Low Z Output Hold Time Output Disable Time Min Unit Max 40 MHz ns ns ns ns ns ns ns ns ns 11 11 20 10 10 5 5 5 5 9 15 15 ns ns ns ns ns 0 25 Figure 21. Synchronous Data Timing (Mode 0) tCS CS tCSS tCH tCL tCSH SCK tSD tHD VALID IN SI tCO SO tOH tHZCS HI-Z HI-Z ~ ~ ~ ~ Figure 22. HOLD Timing CS SCK tSH tHH tHH tSH HOLD tHHZ tHLZ SO Document #: 001-50091 Rev. *B Page 15 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY AutoStore or Power Up RECALL Parameters Power Up RECALL Duration tFA [7] tSTORE CY14B101Q1/CY14B101Q2/ CY14B101Q3 Min Max 20 Description Unit ms [8] STORE Cycle Duration 8 ms [9] Time Allowed to Complete SRAM Cycle 25 ns 2.65 V s tDELAY VSWITCH tVCCRISE [6] Low Voltage Trigger Level VCC Rise Time 150 VHDIS[6] HSB Output Disable Voltage 1.9 V tLZHSB[6] tHHHD[6] HSB To Output Active Time 5 s 500 ns HSB High Active Time Switching Waveforms Figure 23. AutoStore or Power Up RECALL[10] VCC VSWITCH VHDIS 8 VVCCRISE Note 8 tSTORE Note tSTORE 11 tHHHD Note tHHHD HSB OUT tDELAY tLZHSB AutoStore tLZHSB tDELAY POWERUP RECALL Read & Write Inhibited (RWI) tFA POWER-UP RECALL Read & Write tFA BROWN OUT AutoStore POWER-UP RECALL Read & Write POWER DOWN AutoStore Notes 7. tFA starts from the time VCC rises above VSWITCH. 8. If an SRAM write has not taken place since the last nonvolatile cycle, AutoStore or Hardware Store is not initiated 9. On a Hardware STORE, Software Store / RECALL, AutoStore Enable / Disable and AutoStore initiation, SRAM operation continues to be enabled for time tDELAY. 10. Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH. 11. HSB pin is driven high to VCC only by internal 100kOhm resistor, HSB driver is disabled. Document #: 001-50091 Rev. *B Page 16 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Software Controlled STORE and RECALL Cycles Parameter CY14B101Q1/CY14B101Q2/ CY14B101Q3 Description Min Unit Max tRECALL RECALL Duration 200 s tSS [12, 13] Soft Sequence Processing Time 100 s Switching Waveforms Figure 24. Software STORE Cycle[12] CS 0 1 2 3 4 5 6 7 SCK SI 0 0 1 1 1 1 0 0 tSTORE Hi-Z RWI RDY Figure 25. Software RECALL Cycle[12] CS 0 1 2 3 4 5 6 7 0 1 1 0 0 0 0 0 SCK SI tRECALL RWI Hi-Z RDY Notes 12. This is the amount of time it takes to take action on a soft sequence command. Vcc power must remain HIGH to effectively register command. 13. Commands such as STORE and RECALL lock out IO until operation is complete which further increases this time. See the specific command. Document #: 001-50091 Rev. *B Page 17 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Hardware STORE Cycle Parameter CY14B101Q3 Description Min tDHSB HSB To Output Active Time when write latch not set tPHSB Hardware STORE Pulse Width Switching Waveforms Write Latch set Max 25 15 Unit ns ns Figure 26. Hardware STORE Cycle[8] ~ ~ tPHSB HSB (IN) tSTORE tDELAY ~ ~ ~ ~ HSB (OUT) tHHHD SO tLZHSB RWI HSB (OUT) tDELAY RWI Document #: 001-50091 Rev. *B tDHSB HSB pin is driven high to VCC only by Internal 100K: resistor, HSB driver is disabled SRAM is disabled as long as HSB (IN) is driven LOW. tDHSB ~ ~ tPHSB HSB (IN) ~ ~ Write Latch not set Page 18 of 22 [+] Feedback CY14B101Q1 CY14B101Q2 CY14B101Q3 PRELIMINARY Part Numbering Nomenclature CY 14 B 101 Q 1-SF X C T Option: T - Tape & Reel Blank - Std. Temperature: C - Commercial (0 to 70C) I - Industrial (-40 to 85C) Pb-Free Package: SF - 16 SOIC LH - 8 DFN 1 - 8 DFN (with WP) 2 - 8 DFN (With VCAP) 3 - 16 SOIC Q - Serial SPI nvSRAM Density: 101 - 1 Mb Voltage: B - 3.0V nvSRAM 14 - Auto Store + Software STORE + Hardware STORE Cypress Ordering Information Ordering Code Package Diagram Package Type CY14B101Q1-LHXIT 001-50671 8 DFN (with WP) CY14B101Q1-LHXI 001-50671 8 DFN (with WP) CY14B101Q1-LHXCT 001-50671 8 DFN (with WP) CY14B101Q1-LHXC 001-50671 8 DFN (with WP) CY14B101Q2-LHXIT 001-50671 8 DFN (with VCAP) CY14B101Q2-LHXI 001-50671 8 DFN (with VCAP) CY14B101Q2-LHXCT 001-50671 8 DFN (with VCAP) CY14B101Q2-LHXC 001-50671 8 DFN (with VCAP) CY14B101Q3-SFXIT 51-85022 16 SOIC CY14B101Q3-SFXI 51-85022 16 SOIC CY14B101Q3-SFXCT 51-85022 16 SOIC CY14B101Q3-SFXC 51-85022 16 SOIC Operating Range Industrial Commercial Industrial Commercial Industrial Commercial All the above parts are Pb - free. The above table contains advance information. Contact your local Cypress sales representative for availability of these parts. Document #: 001-50091 Rev. *B Page 19 of 22 [+] Feedback PRELIMINARY CY14B101Q1 CY14B101Q2 CY14B101Q3 Package Diagrams Figure 27. 8-Pin (196 mil) DFN Package (001-50671) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS 2. PACKAGE WEIGHT: TBD 3. BASED ON REF JEDEC # MO-240 EXCEPT DIMENSIONS (L) and (b) Document #: 001-50091 Rev. *B 001-50671 *A Page 20 of 22 [+] Feedback PRELIMINARY CY14B101Q1 CY14B101Q2 CY14B101Q3 Package Diagrams (continued) Figure 28. 16-Pin (300 mil) SOIC (51-85022) 51-85022 *B Document #: 001-50091 Rev. *B Page 21 of 22 [+] Feedback PRELIMINARY CY14B101Q1 CY14B101Q2 CY14B101Q3 Document History Page Document Title: CY14B101Q1/CY14B101Q2/CY14B101Q3 1 MBit (128K x 8) Serial SPI nvSRAM Document Number: 001-50091 Orig. of Submission REV. ECN NO. Description of Change Change Date ** 2607408 GSIN/ 12/19/08 New Datasheet GVCH/AESA *A 2654487 GVCH/PYRS 02/04/2009 Moved from Advance information to Preliminary Changed part number from CY14B101QxA to CY14B101Qx Updated pin description of VCAP pin Updated Device operation and SPI peripheral interface description Added Factory setting values for BP1, BP2 and WPEN bits Updated Real Time Clock operation description Changed ICC2 from 5mA to 10mA *B 2733293 GVCH/AESA 07/08/2009 Corrected typo error in the Document History Page (Description of change) Corrected Typo error of footnote 2 and 3 Updated AtoStore operation description Updated test condition of ICC1 and ISB parameter Updated VHDIS parameter description Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products PSoC Clocks & Buffers PSoC Solutions psoc.cypress.com clocks.cypress.com General Low Power/Low Voltage psoc.cypress.com/solutions psoc.cypress.com/low-power Wireless wireless.cypress.com Precision Analog Memories memory.cypress.com LCD Drive psoc.cypress.com/lcd-drive image.cypress.com CAN 2.0b psoc.cypress.com/can USB psoc.cypress.com/usb Image Sensors psoc.cypress.com/precision-analog (c) Cypress Semiconductor Corporation, 2008-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 001-50091 Rev. *B Revised July 02, 2009 Page 22 of 22 All products and company names mentioned in this document are the trademarks of their respective holders. [+] Feedback