LTC1407/LTC1407A Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling ADCs with Shutdown FEATURES DESCRIPTION n The LTC(R)1407/LTC1407A are 12-bit/14-bit, 3Msps ADCs with two 1.5Msps simultaneously sampled differential inputs. The devices draw only 4.7mA from a single 3V supply and come in a tiny 10-lead MS package. A Sleep shutdown feature lowers power consumption to 10W. The combination of speed, low power and tiny package makes the LTC1407/LTC1407A suitable for high speed, portable applications. n n n n n n n n n n 3Msps Sampling ADC with Two Simultaneous Differential Inputs 1.5Msps Throughput per Channel Low Power Dissipation: 14mW (Typ) 3V Single Supply Operation 2.5V Internal Bandgap Reference with External Overdrive 3-Wire Serial Interface Sleep (10W) Shutdown Mode Nap (3mW) Shutdown Mode 80dB Common Mode Rejection at 100kHz 0V to 2.5V Unipolar Input Range Tiny 10-Lead MS Package The LTC1407/LTC1407A contain two separate differential inputs that are sampled simultaneously on the rising edge of the CONV signal. These two sampled inputs are then converted at a rate of 1.5Msps per channel. The 80dB common mode rejection allows users to eliminate ground loops and common mode noise by measuring signals differentially from the source. APPLICATIONS n n n n n n Telecommunications Data Acquisition Systems Uninterrupted Power Supplies Multiphase Motor Control I and Q Demodulation Industrial Control The devices convert 0V to 2.5V unipolar inputs differentially. The absolute voltage swing for CH0+, CH0-, CH1+ and CH1- extends from ground to the supply voltage. The serial interface sends out the two conversion results in 32 clocks for compatibility with standard serial interfaces. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6084440, 6522187. BLOCK DIAGRAM 3V + CH0- 2 - S AND H MUX CH1+ 4 + S AND H CH1- 5 3 10F - GND 11 -44 LTC1407A -50 -56 THREESTATE SERIAL OUTPUT PORT SDO 8 10 CONV 9 SCK TIMING LOGIC VREF 6 3Msps 14-BIT ADC VDD THD, 2nd, 3rd (dB) 1 14-BIT LATCH 7 CH0+ THD, 2nd and 3rd vs Input Frequency 14-BIT LATCH 10F THD 2nd -62 -68 -74 3rd -80 -86 -92 -98 2.5V REFERENCE -104 0.1 1 10 FREQUENCY (MHz) 100 1407 G02 EXPOSED PAD 1407A BD 1407fb 1 LTC1407/LTC1407A ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Notes 1, 2) Supply Voltage (VDD) .................................................4V Analog Input Voltage (Note 3) ..... -0.3V to (VDD + 0.3V) Digital Input Voltage .................... -0.3V to (VDD + 0.3V) Digital Output Voltage ................. -0.3V to (VDD + 0.3V) Power Dissipation ...............................................100mW Operation Temperature Range LTC1407C/LTC1407AC ............................. 0C to 70C LTC1407I/LTC1407AI ...........................- 40C to 85C LTC1407H/LTC1407AH .......................- 40C to 125C Storage Temperature Range...................-65C to 150C Lead Temperature (Soldering, 10 sec) .................. 300C TOP VIEW CH0+ CH0- VREF CH1+ CH1- 1 2 3 4 5 10 9 8 7 6 11 CONV SCK SDO VDD GND MSE PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 150C, JA = 40C/W EXPOSED PAD (PIN #) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC1407CMSE#PBF LTC1407CMSE#TRPBF LTBDQ 10-Lead Plastic MSOP 0C to 70C LTC1407IMSE#PBF LTC1407IMSE#TRPBF LTBDR 10-Lead Plastic MSOP -40C to 85C LTC1407HMSE#PBF LTC1407HMSE#TRPBF LTBDR 10-Lead Plastic MSOP -40C to 125C LTC1407ACMSE#PBF LTC1407ACMSE#TRPBF LTAFE 10-Lead Plastic MSOP 0C to 70C LTC1407AIMSE#PBF LTC1407AIMSE#TRPBF LTAFF 10-Lead Plastic MSOP -40C to 85C LTC1407AHMSE#PBF LTC1407AHMSE#TRPBF LTAFF 10-Lead Plastic MSOP -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. With internal reference, VDD = 3V. PARAMETER CONDITIONS MIN l Resolution (No Missing Codes) LTC1407 LTC1407A LTC1407H LTC1407AH TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX 12 14 12 14 UNITS Bits Integral Linearity Error (Notes 5, 17) l -2 0.25 2 -4 0.5 4 -2 0.25 2 -4 0.5 4 LSB Offset Error (Notes 4, 17) l -10 1 10 -20 2 20 -20 1 20 -30 2 30 LSB Offset Match from CH0 to CH1 (Note 17) -5 0.5 5 -10 1 10 -5 0.5 5 -10 1 10 LSB Gain Error (Notes 4, 17) -30 5 30 -60 10 60 -40 5 40 -80 10 80 LSB Gain Match from CH0 to CH1 (Note 17) -5 1 5 -10 10 -5 1 5 -10 10 LSB Gain Tempco Internal Reference (Note 4) External Reference l 15 1 2 15 1 15 1 2 15 1 ppm/C ppm/C 1407fb 2 LTC1407/LTC1407A ANALOG INPUT The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. With internal reference, VDD = 3V. SYMBOL PARAMETER CONDITIONS VIN Analog Differential Input Range (Notes 3, 9) VCM Analog Common Mode + Differential Input Range (Note 10) IIN Analog Input Leakage Current CIN Analog Input Capacitance tACQ Sample-and-Hold Acquisition Time tAP Sample-and-Hold Aperture Delay Time tJITTER MIN 2.7V VDD 3.3V TYP MAX UNITS 0 to 2.5 V 0 to VDD V l 1 A 39 ns 13 pF l (Note 6) 1 ns Sample-and-Hold Aperture Delay Time Jitter 0.3 ps tSK Sample-and-Hold Aperture Skew from CH0 to CH1 200 ps CMRR Analog Input Common Mode Rejection Ratio -60 -15 dB dB fIN = 1MHz, VIN = 0V to 3V fIN = 100MHz, VIN = 0V to 3V DYNAMIC ACCURACY The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. With internal reference, VDD = 3V. LTC1407/LTC1407H LTC1407A/LTC1407AH MIN TYP MAX MIN TYP MAX SYMBOL PARAMETER CONDITIONS SINAD Signal-to-Noise Plus Distortion Ratio 100kHz Input Signal 750kHz Input Signal 750kHz Input Signal (H Grade) 100kHz Input Signal, External VREF = 3.3V, VDD 3.3V 750kHz Input Signal, External VREF = 3.3V, VDD 3.3V Total Harmonic Distortion 100kHz First 5 Harmonics 750kHz First 5 Harmonics 750kHz First 5 Harmonics (H Grade) SFDR Spurious Free Dynamic Range 100kHz Input Signal 750kHz Input Signal 87 83 90 86 dB dB IMD Intermodulation Distortion 1.25V to 2.5V 1.40MHz into CH0+, 0V to 1.25V, 1.56MHz into CH0-. Also Applicable to CH1+ and CH1- -82 -82 dB Code-to-Code Transition Noise VREF = 2.5V (Note 17) 0.25 1 LSBRMS Full Power Bandwidth VIN = 2.5VP-P, SDO = 11585LSBP-P (-3dBFS) (Note 15) 50 50 MHz Full Linear Bandwidth S/(N + D) 68dB 5 5 MHz THD l l l l 68 67 70.5 70.5 70.5 72.0 72.0 -87 -83 -82 70 69 73.5 73.5 73.5 76.3 76.3 -90 -86 -85 -77 -76 UNITS dB dB dB dB dB -80 -79 dB dB dB INTERNAL REFERENCE CHARACTERISTICS TA = 25C. VDD = 3V. PARAMETER CONDITIONS VREF Output Voltage IOUT = 0 VREF Output Tempco MIN TYP MAX UNITS 2.5 V 15 ppm/C V/V VREF Line Regulation VDD = 2.7V to 3.6V, VREF = 2.5V 600 VREF Output Resistance Load Current = 0.5mA 0.2 2 ms VREF Setting Time 1407fb 3 LTC1407/LTC1407A DIGITAL INPUTS AND DIGITAL OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VDD = 3V. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VIH High Level Input Voltage VDD = 3.3V l VIL Low Level Input Voltage VDD = 2.7V l 0.6 V IIN Digital Input Current VIN = 0V to VDD l 10 A CIN Digital Input Capacitance VOH High Level Output Voltage VDD = 3V, IOUT = -200A l VOL Low Level Output Voltage VDD = 2.7V, IOUT = 160A VDD = 2.7V, IOUT = 1.6mA l VOUT = 0V to VDD l IOZ Hi-Z Output Leakage DOUT COZ Hi-Z Output Capacitance DOUT ISOURCE Output Short-Circuit Source Current ISINK Output Short-Circuit Sink Current 2.4 V 2.5 5 pF 2.9 V 0.05 0.10 0.4 V V 10 A 1 pF VOUT = 0V, VDD = 3V 20 mA VOUT = VDD = 3V 15 mA POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. With internal reference, VDD = 3V. SYMBOL PARAMETER VDD Supply Voltage IDD Supply Current PD CONDITIONS MIN TYP MAX 2.7 l l l l Active Mode, fSAMPLE = 1.5Msps Active Mode (LTC1407H/LTC1407AH) Nap Mode Nap Mode (LTC1407H/LTC1407AH) Sleep Mode (LTC1407/LTC1407H) Sleep Mode (LTC1407A/LTC1407AH) 4.7 5.2 1.1 1.2 2.0 2.0 Active Mode with SCK in Fixed State (Hi or Lo) 12 UNITS 3.6 V 7.0 8.0 1.5 1.8 15 10 mA mA mA mA A A mW TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VDD = 3V. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS fSAMPLE(MAX) Maximum Sampling Frequency per Channel (Conversion Rate) l tTHROUGHPUT Minimum Sampling Period (Conversion + Acquisiton Period) l tSCK Clock Period (Note 16) tCONV Conversion Time (Note 6) 32 t1 Minimum Positive or Negative SCLK Pulse Width (Note 6) 2 t2 CONV to SCK Setup Time (Notes 6, 10) 3 t3 SCK Before CONV (Note 6) 0 ns t4 Minimum Positive or Negative CONV Pulse Width (Note 6) 4 ns t5 SCK to Sample Mode (Note 6) 4 ns t6 CONV to Hold Mode (Notes 6, 11) 1.2 ns l 1.5 MHz 19.6 667 ns 10000 ns 34 SCLK cycles ns 10000 ns 1407fb 4 LTC1407/LTC1407A TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VDD = 3V. PARAMETER CONDITIONS t7 32nd SCK to CONV Interval (Affects Acquisition Period) (Notes 6, 7, 13) 45 ns t8 Minimum Delay from SCK to Valid Bits 0 Through 11 (Notes 6, 12) 8 ns t9 SCK to Hi-Z at SDO (Notes 6, 12) 6 ns t10 Previous SDO Bit Remains Valid After SCK (Notes 6, 12) 2 ns t12 VREF Settling Time After Sleep-to-Wake Transition (Notes 6, 14) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground GND. Note 3: When these pins are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents greater than 100mA below GND or greater than VDD without latchup. Note 4: Offset and range specifications apply for a single-ended CH0+ or CH1+ input with CH0 - or CH1- grounded and using the internal 2.5V reference. Note 5: Integral linearity is tested with an external 2.55V reference and is defined as the deviation of a code from the straight line passing through the actual endpoints of a transfer curve. The deviation is measured from the center of quantization band. Note 6: Guaranteed by design, not subject to test. Note 7: Recommended operating conditions. Note 8: The analog input range is defined for the voltage difference between CH0+ and CH0- or CH1+ and CH1-. Note 9: The absolute voltage at CH0+, CH0-, CH1+ and CH1- must be within this range. 74 11.5 71 10.5 65 10.0 62 9.5 59 9.0 56 8.5 53 8.0 0.1 1 10 FREQUENCY (MHz) 50 100 1407 G01 THD, 2nd, 3rd (dB) ENOBs (BITS) 68 SFDR vs Input Frequency 98 THD 92 2nd -62 86 -68 -74 3rd -80 80 74 68 62 -86 -92 56 -98 50 -104 0.1 ms 104 -50 SINAD (dB) 11.0 UNITS VDD = 3V, TA = 25C (LTC1407A) -44 -56 MAX 2 THD, 2nd and 3rd vs Input Frequency 12.0 TYP Note 10: If less than 3ns is allowed, the output data will appear one clock cycle later. It is best for CONV to rise half a clock before SCK, when running the clock at rated speed. Note 11: Not the same as aperture delay. Aperture delay (1ns) is the difference between the 2.2ns delay through the sample-and-hold and the 1.2ns CONV to Hold mode delay. Note 12: The rising edge of SCK is guaranteed to catch the data coming out into a storage latch. Note 13: The time period for acquiring the input signal is started by the 32nd rising clock and it is ended by the rising edge of CONV. Note 14: The internal reference settles in 2ms after it wakes up from Sleep mode with one or more cycles at SCK and a 10F capacitive load. Note 15: The full power bandwidth is the frequency where the output code swing drops by 3dB with a 2.5VP-P input sine wave. Note 16: Maximum clock period guarantees analog performance during conversion. Output data can be read with an arbitrarily long clock period. Note 17: The LTC1407A is measured and specified with 14-bit resolution (1LSB = 152V) and the LTC1407 is measured and specified with 12-bit resolution (1LSB = 610V). TYPICAL PERFORMANCE CHARACTERISTICS ENOBs and SINAD vs Input Sinewave Frequency MIN SFDR (dB) SYMBOL 1 10 FREQUENCY (MHz) 100 1407 G02 44 0.1 1 10 FREQUENCY (MHz) 100 1407 G19 1407fb 5 LTC1407/LTC1407A TYPICAL PERFORMANCE CHARACTERISTICS 98kHz Sine Wave 4096 Point FFT Plot SNR vs Input Frequency 74 0 MAGNITUDE (dB) 68 SNR (dB) 65 62 59 1 10 FREQUENCY (MHz) 100 -20 -20 -30 -30 -40 -40 -50 -60 -70 -80 -90 -110 -110 -120 -120 0 100 200 300 400 500 FREQUENCY (kHz) 600 -40 -50 -60 -70 -80 -90 -100 -110 100 200 300 400 500 FREQUENCY (kHz) 600 700 1.0 2.0 1.6 0.6 1.2 0.4 0.2 0 -0.2 -0.4 -0.6 0 -0.4 -0.8 -1.2 -1.6 -2.0 0 4096 12288 8192 OUTPUT CODE 16384 4096 12288 8192 OUTPUT CODE 2.0 0.8 1.6 0.6 1.2 0.2 0 -0.2 -0.4 -0.6 0.4 0 -0.4 -0.8 -1.2 -1.6 -1.0 -2.0 1407 G17 1407 G16 0.8 -0.8 16384 16384 Integral Linearity End Point Fit for CH1 with Internal 2.5V Reference 1.0 12288 8192 OUTPUT CODE 0 1407 G15 0.4 700 0.8 -1.0 INTEGRAL LINEARITY (LSB) DIFFERENTIAL LINEARITY (LSB) 600 0.4 -0.8 Differential Linearity for CH1 with Internal 2.5V Reference 4096 200 300 400 500 FREQUENCY (kHz) Integral Linearity End Point Fit for CH0 with Internal 2.5V Reference 0.8 1407 G06 0 100 1407 G05 INTEGRAL LINEARITY (LSB) DIFFERENTIAL LINEARITY (LSB) MAGNITUDE (dB) -30 0 1407 G04 1.5Msps 0 700 Differential Linearity for CH0 with Internal 2.5V Reference -20 -120 -80 -100 1407 G03 0 -60 -70 -100 1403kHz Input Summed with 1563kHz Input IMD 4096 Point FFT Plot -10 -50 -90 56 53 0 1.5Msps -10 MAGNITUDE (dB) 71 748kHz Sine Wave 4096 Point FFT Plot 1.5Msps -10 50 0.1 VDD = 3V, TA = 25C (LTC1407A) 0 4096 12288 8192 OUTPUT CODE 16384 1407 G18 1407fb 6 LTC1407/LTC1407A TYPICAL PERFORMANCE CHARACTERISTICS VDD = 3V, TA = 25C (LTC1407/LTC1407A) Full-Scale Signal Frequency Response CMRR vs Frequency 12 Crosstalk vs Frequency -20 0 6 -30 -20 CROSSTALK (dB) -40 -40 CMRR (dB) -6 -12 -18 -60 CH0 CH1 -80 -100 -30 -36 1M 10M 100M FREQUENCY (Hz) 1k 10k 100k 1M FREQUENCY (Hz) 10M 1407 G07 CH1 TO CH0 CH0 TO CH1 100M -90 100 1k 10k 100k FREQUENCY (Hz) 1M 10M 1407 G09 1407 G08 Simultaneous Input Steps at CH0 and CH1 from 25 PSSR vs Frequency 3.0 -25 2.6 -30 2.2 -35 -40 1.8 PSRR (dB) ANALOG INPUTS (V) -60 -80 -120 100 1G -50 -70 -24 CH0 CH1 1.4 1.0 -45 -50 0.6 -55 0.2 -60 -0.2 -65 -70 -0.6 0 5 10 15 20 TIME (ns) 1 30 25 10 100 1k 10k FREQUENCY (Hz) 100k 1M 1407 G11 1407 G10 Reference Voltage vs Load Current Reference Voltage vs VDD 2.4902 2.4900 2.4900 2.4898 2.4898 VREF (V) 2.4902 VREF (V) AMPLITUDE (dB) 0 2.4896 2.4896 2.4894 2.4894 2.4892 2.4892 2.4890 2.4890 2.6 2.8 3.0 3.2 VDD (V) 3.4 3.6 1407 G12 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 LOAD CURRENT (mA) 1407 G13 1407fb 7 LTC1407/LTC1407A PIN FUNCTIONS CH0+ (Pin 1): Noninverting Channel 0. CH0+ operates fully differentially with respect to CH0- with a 0V to 2.5V differential swing and a 0 to VDD absolute input range. CH0- (Pin 2): Inverting Channel 0. CH0- operates fully differentially with respect to CH0+ with a -2.5V to 0V differential swing and a 0 to VDD absolute input range. VREF (Pin 3): 2.5V Internal Reference. Bypass to GND and a solid analog ground plane with a 10F ceramic capacitor (or 10F tantalum in parallel with 0.1F ceramic). Can be overdriven by an external reference voltage 2.55V and VDD. VDD (Pin 7): 3V Positive Supply. This single power pin supplies 3V to the entire chip. Bypass to GND pin and solid analog ground plane with a 10F ceramic capacitor (or 10F tantalum) in parallel with 0.1F ceramic. Keep in mind that internal analog currents and digital output signal currents flow through this pin. Care should be taken to place the 0.1F bypass capacitor as close to Pins 6 and 7 as possible. SDO (Pin 8): Three-State Serial Data Output. Each pair of output data words represent the two analog input channels at the start of the previous conversion. CH1+ (Pin 4): Noninverting Channel 1. CH1+ operates fully differentially with respect to CH1- with a 0V to 2.5V differential swing and a 0 to VDD absolute input range. SCK (Pin 9): External Clock Input. Advances the conversion process and sequences the output data on the rising edge. One or more pulses wake from sleep. CH1- (Pin 5): Inverting Channel 1. CH1- operates fully differentially with respect to CH1+ with a -2.5V to 0V differential swing and a 0 to VDD absolute input range. CONV (Pin 10): Convert Start. Holds the two analog input signals and starts the conversion on the rising edge. Two pulses with SCK in fixed high or fixed low state starts Nap mode. Four or more pulses with SCK in fixed high or fixed low state starts Sleep mode. GND (Pins 6, 11): Ground and Exposed Pad. This single ground pin and the Exposed Pad must be tied directly to the solid ground plane under the part. Keep in mind that analog signal currents and digital output signal currents flow through these connections. BLOCK DIAGRAM 3V 1 + CH0- 2 - S AND H MUX CH1+ 4 CH1- 5 + S AND H 3 10F - 6 11 LTC1407A THREESTATE SERIAL OUTPUT PORT 8 SDO 10 CONV 9 SCK TIMING LOGIC VREF GND 3Msps 14-BIT ADC VDD 14-BIT LATCH 7 CH0+ 14-BIT LATCH 10F 2.5V REFERENCE EXPOSED PAD 1407A BD 1407fb 8 SDO INTERNAL S/H STATUS CONV SCK SDO INTERNAL S/H STATUS CONV SCK t6 t4 34 t6 t4 34 SAMPLE 33 SAMPLE 33 Hi-Z t3 t8 2 3 D11 4 6 HOLD 7 1 Hi-Z t3 2 t8 t2 3 D13 4 8 t1 9 t10 10 11 12 13 14 15 D10 D9 D8 6 HOLD 7 8 t1 D6 D4 9 t10 10 11 12-BIT DATA WORD D5 D3 12 D2 13 D0 D12 D11 D10 D9 D8 D6 14-BIT DATA WORD D7 D5 D4 X* X* 17 19 14 15 D3 D2 D1 t9 16 D0 17 19 21 22 HOLD 23 24 25 26 27 28 29 30 t8 20 D10 21 D9 22 D8 HOLD 23 D7 24 D6 D4 25 26 27 12-BIT DATA WORD D5 D3 28 D2 29 D1 30 D0 D12 D11 D10 D9 D8 D6 14-BIT DATA WORD D7 D5 D4 D3 D2 SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION AT CH1 D13 tTHROUGHPUT tCONV Hi-Z 18 t8 20 SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION AT CH1 D11 tTHROUGHPUT tCONV Hi-Z 18 LTC1407A Timing Diagram D1 SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION AT CH0 5 D7 t9 16 LTC1407 Timing Diagram SDO REPRESENTS THE ANALOG INPUT FROM THE PREVIOUS CONVERSION AT CH0 5 *BITS MARKED "X" AFTER D0 SHOULD BE IGNORED 1 t2 t5 31 t5 31 D1 X* t8 32 t8 32 D0 X* 34 tACQ 34 Hi-Z t9 SAMPLE 33 t7 Hi-Z t9 SAMPLE tACQ t7 33 HOLD HOLD 1407A TD01 1 1407A TD01 1 LTC1407/LTC1407A TIMING DIAGRAMS 1407fb 9 LTC1407/LTC1407A TIMING DIAGRAMS Nap Mode Waveforms SCK t1 CONV NAP Sleeep Mode Waveforms SCK t1 t1 CONV NAP SLEEP t12 VREF 1407 TD02 NOTE: NAP AND SLEEP ARE INTERNAL SIGNALS SCK to SDO Delay SCK VIH SCK VIH t8 t10 SDO t9 VOH 90% SDO 10% VOL 1407 TD03 1407fb 10 LTC1407/LTC1407A APPLICATIONS INFORMATION DRIVING THE ANALOG INPUT The differential analog inputs of the LTC1407/LTC1407A are easy to drive. The inputs may be driven differentially or as a single-ended input (i.e., the CH0- input is grounded). All four analog inputs of both differential analog input pairs, CH0+ with CH0- and CH1+ with CH1-, are sampled at the same instant. Any unwanted signal that is common to both inputs of each input pair will be reduced by the common mode rejection of the sample-and-hold circuit. The inputs draw only one small current spike while charging the sample-and-hold capacitors at the end of conversion. During conversion, the analog inputs draw only a small leakage current. If the source impedance of the driving circuit is low, then the LTC1407/LTC1407A inputs can be driven directly. As source impedance increases, so will acquisition time. For minimum acquisition time with high source impedance, a buffer amplifier must be used. The main requirement is that the amplifier driving the analog input(s) must settle after the small current spike before the next conversion starts (settling time must be 39ns for full throughput rate). Also keep in mind, while choosing an input amplifier, the amount of noise and harmonic distortion added by the amplifier. CHOOSING AN INPUT AMPLIFIER Choosing an input amplifier is easy if a few requirements are taken into consideration. First, to limit the magnitude of the voltage spike seen by the amplifier from charging the sampling capacitor, choose an amplifier that has a low output impedance (< 100) at the closed-loop bandwidth frequency. For example, if an amplifier is used in a gain of 1 and has a unity-gain bandwidth of 50MHz, then the output impedance at 50MHz must be less than 100. The second requirement is that the closed-loop bandwidth must be greater than 40MHz to ensure adequate small-signal settling for full throughput rate. If slower op amps are used, more time for settling can be provided by increasing the time between conversions. The best choice for an op amp to drive the LTC1407/LTC1407A depends on the application. Generally, applications fall into two categories: AC applications where dynamic specifications are most critical and time domain applications where DC accuracy and settling time are most critical. The following list is a summary of the op amps that are suitable for driving the LTC1407/LTC1407A. (More detailed information is available in the Linear Technology Databooks and on the LinearViewTM CD-ROM.) LTC1566-1: Low Noise 2.3MHz Continuous Time Lowpass Filter. LT(R)1630: Dual 30MHz Rail-to-Rail Voltage FB Amplifier. 2.7V to 15V supplies. Very high AVOL, 500V offset and 520ns settling to 0.5LSB for a 4V swing. THD and noise are - 93dB to 40kHz and below 1LSB to 320kHz (AV = 1, 2VP-P into 1k, VS = 5V), making the part excellent for AC applications (to 1/3 Nyquist) where rail-to-rail performance is desired. Quad version is available as LT1631. LT1632: Dual 45MHz Rail-to-Rail Voltage FB Amplifier. 2.7V to 15V supplies. Very high AVOL, 1.5mV offset and 400ns settling to 0.5LSB for a 4V swing. It is suitable for applications with a single 5V supply. THD and noise are - 93dB to 40kHz and below 1LSB to 800kHz (AV = 1, 2VP-P into 1k, VS = 5V), making the part excellent for AC applications where rail-to-rail performance is desired. Quad version is available as LT1633. LT1801: 80MHz GBWP, -75dBc at 500kHz, 2mA/amplifier, 8.5nV/Hz. LT1806/LT1807: 325MHz GBWP, -80dBc distortion at 5MHz, unity-gain stable, rail-to-rail in and out, 10mA/amplifier, 3.5nV/Hz. LT1810: 180MHz GBWP, -90dBc distortion at 5MHz, unity-gain stable, rail-to-rail in and out, 15mA/amplifier, 16nV/Hz. LinearView is a trademark of Linear Technology Corporation. 1407fb 11 LTC1407/LTC1407A APPLICATIONS INFORMATION LT1818/LT1819: 400MHz, 2500V/s, 9mA, Single/Dual Voltage Mode Operational Amplifier. inputs to minimize noise. A simple 1-pole RC filter is sufficient for many applications. For example, Figure 1 shows a 47pF capacitor from CHO+ to ground and a 51 source resistor to limit the net input bandwidth to 30MHz. The 47pF capacitor also acts as a charge reservoir for the input sample-and-hold and isolates the ADC input from sampling-glitch sensitive circuitry. High quality capacitors and resistors should be used since these components can add distortion. NPO and silvermica type dielectric capacitors have excellent linearity. Carbon surface mount resistors can generate distortion from self heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to both problems. When high amplitude unwanted signals are close in frequency to the desired signal frequency a multiple pole filter is required. LT6200: 165MHz GBWP, -85dBc distortion at 1MHz, unity-gain stable, rail-to-rail in and out, 15mA/amplifier, 0.95nV/Hz. LT6203: 100MHz GBWP, -80dBc distortion at 1MHz, unity-gain stable, rail-to-rail in and out, 3mA/amplifier, 1.9nV/Hz. LT6600: Amplifier/Filter Differential In/Out with 10MHz Cutoff. INPUT FILTERING AND SOURCE IMPEDANCE The noise and the distortion of the input amplifier and other circuitry must be considered since they will add to the LTC1407/LTC1407A noise and distortion. The smallsignal bandwidth of the sample-and-hold circuit is 50MHz. Any noise or distortion products that are present at the analog inputs will be summed over this entire bandwidth. Noisy input circuitry should be filtered prior to the analog ANALOG INPUT 51* High external source resistance, combined with 13pF of input capacitance, will reduce the rated 50MHz input bandwidth and increase acquisition time beyond 39ns. 1 47pF* 2 3 10F 11 ANALOG INPUT 51* 4 47pF* 5 CH0+ CH0- LTC1407/ LTC1407A VREF GND CH1+ CH1- 1407 F01 *TIGHT TOLERANCE REQUIRED TO AVOID APERTURE SKEW DEGRADATION Figure 1. RC Input Filter 1407fb 12 LTC1407/LTC1407A APPLICATIONS INFORMATION INPUT RANGE The analog inputs of the LTC1407/LTC1407A may be driven fully differentially with a single supply. Either input may swing up to 3V, provided the differential swing is no greater than 2.5V. In the valid input range, the noninverting input of each channel should always be more positive than the inverting input of each channel. The 0V to 2.5V range is also ideally suited for single-ended input use with single supply applications. The common mode range of the inputs extend from ground to the supply voltage VDD. If the difference between the CH0+ and CH0- inputs or the CH1+ and CH1- inputs exceeds 2.5V, the output code will stay fixed at all ones, and if this difference goes below 0V, the ouput code will stay fixed at all zeros. INTERNAL REFERENCE The LTC1407/LTC1407A have an on-chip, temperature compensated, bandgap reference that is factory trimmed near 2.5V to obtain a precise 2.5V input span. The reference amplifier output VREF, (Pin 3) must be bypassed with a capacitor to ground. The reference amplifier is stable with capacitors of 1F or greater. For the best noise performance, a 10F ceramic or a 10F tantalum in parallel with a 0.1F ceramic is recommended. The VREF pin can be overdriven with an external reference as shown in Figure 2. The voltage of the external reference must be higher than the 2.5V of the open-drain P-channel output of the internal reference. The recommended range for an external reference is 2.55V to VDD. An external reference at 2.55V will see a DC quiescent load of 0.75mA and as much as 3mA during conversion. INPUT SPAN VERSUS REFERENCE VOLTAGE The differential input range has a unipolar voltage span that equals the difference between the voltage at the reference buffer output VREF (Pin 3) and the voltage at the Exposed Pad ground. The differential input range of ADC is 0V to 2.5V when using the internal reference. The internal ADC is referenced to these two nodes. This relationship also holds true with an external reference. DIFFERENTIAL INPUTS The ADC will always convert the unipolar difference of CH0+ minus CH0- or the unipolar difference of CH1+ minus CH1-, independent of the common mode voltage at either set of inputs. The common mode rejection holds up at high frequencies (see Figure 3.) The only requirement is that both inputs not go below ground or exceed VDD. 0 10F 11 VREF LTC1407/ LTC1407A GND 1407 F02 Figure 2 -20 -40 CMRR (dB) 3 3V REF -60 CH0 CH1 -80 -100 -120 100 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M 1407 G08 Figure 3. CMRR vs Frequency 1407fb 13 LTC1407/LTC1407A APPLICATIONS INFORMATION Integral nonlinearity errors (INL) and differential nonlinearity errors (DNL) are largely independent of the common mode voltage. However, the offset error will vary. CMRR is typically better than 60dB. Figure 4 shows the ideal input/output characteristics for the LTC1407/LTC1407A. The code transitions occur midway between successive integer LSB values (i.e., 0.5LSB, 1.5LSB, 2.5LSB, FS - 1.5LSB). The output code is natural binary with 1LSB = 2.5V/16384 = 153V for the LTC1407A and 1LSB = 2.5V/4096 = 610V for the LTC1407. The LTC1407A has 1LSB RMS of Gaussian white noise. Board Layout and Bypassing Wire wrap boards are not recommended for high resolution and/or high speed A/D converters. To obtain the best performance from the LTC1407/LTC1407A, a printed circuit board with ground plane is required. Layout for the printed circuit board should ensure that digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital track alongside an analog signal track. If optimum phase match between the inputs is desired, the length of the four input wires of the two input channels should be kept matched. But each pair of input wires to the two input channels should be kept separated by a ground trace to avoid high frequency crosstalk between channels. High quality tantalum and ceramic bypass capacitors should be used at the VDD and VREF pins as shown in the Block Diagram on the first page of this data sheet. For optimum performance, a 10F surface mount tantalum capacitor with a 0.1F ceramic is recommended for the VDD and VREF pins. Alternatively, 10F ceramic chip capacitors such as X5R or X7R may be used. The capacitors must be located as close to the pins as possible. The traces connecting the pins and the bypass capacitors must be kept short and should be made as wide as possible. The VDD bypass capacitor returns to GND (Pin 6) and the VREF bypass capacitor returns to the Exposed Pad ground (Pin 11). Care should be taken to place the 0.1F VDD bypass capacitor as close to Pins 6 and 7 as possible. Figure 5 shows the recommended system ground connections. All analog circuitry grounds should be terminated at the LTC1407/LTC1407A Exposed Pad. The ground return from the LTC1407/LTC1407A Pin 6 to the power supply should be low impedance for noise-free operation. The Exposed Pad of the 10-lead MSE package is also tied to Pin 6 and the LTC1407/LTC1407A GND. The Exposed Pad should be soldered on the PC board to reduce ground connection inductance. Digital circuitry grounds must be connected to the digital supply common. 111...111 UNIPOLAR OUTPUT CODE 111...110 111...101 000...010 000...001 000...000 0 FS - 1LSB INPUT VOLTAGE (V) 1407 F04 Figure 4. LTC1407/LTC1407A Transfer Characteristic 1407fb 14 LTC1407/LTC1407A APPLICATIONS INFORMATION Figure 5. Recommended Layout POWER-DOWN MODES Upon power-up, the LTC1407/LTC1407A are initialized to the active state and are ready for conversion. The Nap and Sleep mode waveforms show the power-down modes for the LTC1407/LTC1407A. The SCK and CONV inputs control the power-down modes (see Timing Diagrams). Two rising edges at CONV, without any intervening rising edges at SCK, put the LTC1407/LTC1407A in Nap mode and the power drain drops from 14mW to 6mW. The internal reference remains powered in Nap mode. One or more rising edges at SCK wake up the LTC1407/LTC1407A for service very quickly and CONV can start an accurate conversion within a clock cycle. Four rising edges at CONV, without any intervening rising edges at SCK, put the LTC1407/LTC1407A in Sleep mode and the power drain drops from 14mW to 10W. To bring the part out of Sleep mode requires one or more rising SCK edges followed by a Nap request. Then one or more rising edges at SCK wake up the LTC1407/LTC1407A for operation. When Nap mode is entered after Sleep mode, the reference that was shut down in Sleep mode is reactivated. The internal reference (VREF ) takes 2ms to slew and settle with a 10F load. Using Sleep mode more frequently compromises the settled accuracy of the internal reference. Note that for slower conversion rates, the Nap and Sleep modes can be used for substantial reductions in power consumption. 1407fb 15 LTC1407/LTC1407A APPLICATIONS INFORMATION DIGITAL INTERFACE The LTC1407/LTC1407A have a 3-wire SPI (Serial Protocol Interface) interface. The SCK and CONV inputs and SDO output implement this interface. The SCK and CONV inputs accept swings from 3V logic and are TTL compatible, if the logic swing does not exceed VDD. A detailed description of the three serial port signals follows: Conversion Start Input (CONV) The rising edge of CONV starts a conversion, but subsequent rising edges at CONV are ignored by the LTC1407/ LTC1407A until the following 32 SCK rising edges have occurred. The duty cycle of CONV can be arbitrarily chosen to be used as a frame sync signal for the processor serial port. A simple approach to generate CONV is to create a pulse that is one SCK wide to drive the LTC1407/LTC1407A and then buffer this signal to drive the frame sync input of the processor serial port. It is good practice to drive the LTC1407/LTC1407A CONV input first to avoid digital noise interference during the sample-to-hold transition triggered by CONV at the start of conversion. It is also good practice to keep the width of the low portion of the CONV signal greater than 15ns to avoid introducing glitches in the front end of the ADC just before the sample-and-hold goes into Hold mode at the rising edge of CONV. Minimizing Jitter on the CONV Input In high speed applications where high amplitude sinewaves above 100kHz are sampled, the CONV signal must have as little jitter as possible (10ps or less). The square wave output of a common crystal clock module usually meets this requirement easily. The challenge is to generate a CONV signal from this crystal clock without jitter corruption from other digital circuits in the system. A clock divider and any gates in the signal path from the crystal clock to the CONV input should not share the same integrated circuit with other parts of the system. As shown in the interface circuit examples, the SCK and CONV inputs should be driven first, with digital buffers used to drive the serial port interface. Also note that the master clock in the DSP may already be corrupted with jitter, even if it comes directly from the DSP crystal. Another problem with high speed processor clocks is that they often use a low cost, low speed crystal (i.e., 10MHz) to generate a fast, but jittery, phase-locked-loop system clock (i.e., 40MHz). The jitter in these PLL-generated high speed clocks can be several nanoseconds. Note that if you choose to use the frame sync signal generated by the DSP port, this signal will have the same jitter of the DSP's master clock. Serial Clock Input (SCK) The rising edge of SCK advances the conversion process and also udpates each bit in the SDO data stream. After CONV rises, the third rising edge of SCK sends out two sets of 12/14 data bits, with the MSB sent first. A simple approach is to generate SCK to drive the LTC1407/LTC1407A first and then buffer this signal with the appropriate number of inverters to drive the serial clock input of the processor serial port. Use the falling edge of the clock to latch data from the Serial Data Output (SDO) into your processor serial port. The 14-bit Serial Data will be received right justified, in two 16-bit words with 32 or more clocks per frame sync. It is good practice to drive the LTC1407/LTC1407A SCK input first to avoid digital noise interference during the internal bit comparison decision by the internal high speed comparator. Unlike the CONV input, the SCK input is not sensitive to jitter because the input signal is already sampled and held constant. Serial Data Output (SDO) Upon power-up, the SDO output is automatically reset to the high impedance state. The SDO output remains in high impedance until a new conversion is started. SDO sends out two sets of 12/14 bits in the output data stream after the third rising edge of SCK after the start of conversion with the rising edge of CONV. The two 12-/14-bit words are separated by two clock cycles in high impedance mode. Please note the delay specification from SCK to a valid SDO. SDO is always guaranteed to be valid by the next rising edge of SCK. The 32-bit output data stream is compatible with the 16-bit or 32-bit serial port of most processors. 1407fb 16 LTC1407/LTC1407A APPLICATIONS INFORMATION HARDWARE INTERFACE TO TMS320C54x The LTC1407/LTC1407A are serial output ADCs whose interface has been designed for high speed buffered serial ports in fast digital signal processors (DSPs). Figure 6 shows an example of this interface using a TMS320C54X. The buffered serial port in the TMS320C54x has direct access to a 2kB segment of memory. The ADC's serial data can be collected in two alternating 1kB segments, in real time, at the full 3Msps conversion rate of the LTC1407/ LTC1407A. The DSP assembly code sets frame sync mode at the BFSR pin to accept an external positive going pulse and the serial clock at the BCLKR pin to accept an external positive edge clock. Buffers near the LTC1407/LTC1407A may be added to drive long tracks to the DSP to prevent corruption of the signal to LTC1407/LTC1407A. This configuration is adequate to traverse a typical system board, but source resistors at the buffer outputs and termination resistors at the DSP, may be needed to match the characteristic impedance of very long transmission lines. If you need to terminate the SDO transmission line, buffer it first with one or two 74ACxx gates. The TTL threshold inputs of the DSP port respond properly to the 3V swing used with the LTC1407/LTC1407A. 3V VDD 5V 7 VCC 10 CONV LTC1407/ LTC1407A 9 SCK SDO GND BFSR TMS320C54x BCLKR B13 8 B12 BDR 6 CONV CLK 3-WIRE SERIAL INTERFACELINK 1407 F06 0V TO 3V LOGIC SWING Figure 6. DSP Serial Interface to TMS320C54x 1407fb 17 LTC1407/LTC1407A APPLICATIONS INFORMATION ; ; ; ; ; ; ; ; ; ; ; ; ; 08-21-03 ****************************************************************** Files: 1407ASIAB.ASM -> 1407A Sine wave collection with Serial Port interface both channels collected in sequence in the same 2k record bvectors.asm buffered mode. s2k14ini.asm 2k buffer size. unipolar mode Works 16 or 64 clock frames. negative edge BCLKR negative BFSR pulse -0 data shifted 1' cable from counter to CONV at DUT 2' cable from counter to CLK at DUT *************************************************************************** .width 160 .length 110 .title "sineb0 BSP in auto buffer mode" .mmregs .setsect ".text", 0x500,0 ;Set address .setsect "vectors", 0x180,0 ;Set address .setsect "buffer", 0x800,0 ;Set address .setsect "result", 0x1800,0 ;Set address .text ;.text marks of executable of incoming 1407A data of BSP buffer for clearing of result for clearing start of code start: ;this label seems necessary ;Make sure /PWRDWN is low at J1-9 ;to turn off AC01 adc tim=#0fh prd=#0fh tcr = #10h tspc = #0h pmst = #01a0h sp = #0700h dp = #0 ar2 = #1800h ar3 = #0800h ar4 = #0h call sineinit sinepeek: call sineinit wait ; goto ; ; ; ; ; ; ; ; stop timer stop TDM serial port to AC01 set up iptr. Processor Mode STatus register init stack pointer. data page pointer to computed receive buffer. pointer to Buffered Serial Port receive buffer reset record counter ; Double clutch the initialization to insure a proper ; reset. The external frame sync must occur 2.5 clocks ; or more after the port comes out of reset. wait ----------------Buffered Receive Interrupt Routine ------------------ breceive: ifr = #10h ; clear interrupt flags TC = bitf(@BSPCE,#4000h) ; check which half (bspce(bit14)) of buffer if (NTC) goto bufull ; if this still the first half get next half bspce = #(2023h + 08000h); turn on halt for second half (bspce(bit15)) return_enable 1407fb 18 LTC1407/LTC1407A APPLICATIONS INFORMATION ; --------------mask and shift input data ---------------------------- bufull: b = *ar3+ << -0 b = #07FFFh & b *ar2+ = data(#0bh) TC = (@ar2 == #02000h) if (TC) goto start goto bufull ; bsend ; ; ; ; ; ; ; load acc b with BSP buffer and shift right -0 mask out the TRISTATE bits with #03FFFh store B to out buffer and advance AR2 pointer output buffer is 2k starting at 1800h restart if out buffer is at 1fffh ------------------dummy bsend return------------------------ return_enable ;this is also a dummy return to define bsend ;in vector table file BVECTORS.ASM ---------------------- end ISR ---------------------------- .copy "c:\dskplus\1407A\s2k14ini.asm" ;initialize buffered serial port .space 16*32 ;clear a chunk at the end to mark the end ;====================================================================== ; ; VECTORS ; ;====================================================================== .sect "vectors" ;The vectors start here .copy "c:\dskplus\1407A\bvectors.asm" ;get BSP vectors .sect "buffer" .space 16*0x800 .sect "result" .space 16*0x800 ;Set address of BSP buffer for clearing ;Set address of result for clearing .end ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; *************************************************************************** File: BVECTORS.ASM -> Vector Table for the `C54x DSKplus 10.Jul.96 BSP vectors and Debugger vectors TDM vectors just return *************************************************************************** The vectors in this table can be configured for processing external and internal software interrupts. The DSKplus debugger uses four interrupt vectors. These are RESET, TRAP2, INT2, and HPIINT. * DO NOT MODIFY THESE FOUR VECTORS IF YOU PLAN TO USE THE DEBUGGER * All other vector locations are free to use. When programming always be sure the HPIINT bit is unmasked (IMR=200h) to allow the communications kernel and host PC interact. INT2 should normally be masked (IMR(bit 2) = 0) so that the DSP will not interrupt itself during a HINT. HINT is tied to INT2 externally. 1407fb 19 LTC1407/LTC1407A APPLICATIONS INFORMATION .title "Vector Table" .mmregs reset nmi trap2 int0 int1 int2 tint brint bxint trint txint int3 hpiint goto #80h nop nop return_enable nop nop nop goto #88h nop nop .space 52*16 return_enable nop nop nop return_enable nop nop nop return_enable nop nop nop return_enable nop nop nop goto breceive nop nop nop goto bsend nop nop nop return_enable nop nop nop return_enable nop nop return_enable nop nop nop dgoto #0e4h nop nop ;00; RESET * DO NOT MODIFY IF USING DEBUGGER * ;04; non-maskable external interrupt ;08; trap2 * DO NOT MODIFY IF USING DEBUGGER * ;0C-3F: vectors for software interrupts 18-30 ;40; external interrupt int0 ;44; external interrupt int1 ;48; external interrupt int2 ;4C; internal timer interrupt ;50; BSP receive interrupt ;54; BSP transmit interrupt ;58; TDM receive interrupt ;5C; TDM transmit interrupt ;60; external interrupt int3 ;64; HPIint * DO NOT MODIFY IF USING DEBUGGER * 1407fb 20 LTC1407/LTC1407A APPLICATIONS INFORMATION .space 24*16 ;68-7F; reserved area ********************************************************************** * (C) COPYRIGHT TEXAS INSTRUMENTS, INC. 1996 * ********************************************************************** * * * File: BSPI1407A.ASM BSP initialization code for the `C54x DSKplus * * for use with 1407A in standard mode * * BSPC and SPC seem interchangeable in the `C542 * * BSPCE and SPCE seem interchangeable in the `C542 * ********************************************************************** .title "Buffered Serial Port Initialization Routine" ON .set 1 OFF .set !ON YES .set 1 NO .set !YES BIT_8 .set 2 BIT_10 .set 1 BIT_12 .set 3 BIT_16 .set 0 GO .set 0x80 ********************************************************************** * This is an example of how to initialize the Buffered Serial Port (BSP). * The BSP is initialized to require an external CLK and FSX for * operation. The data format is 16-bits, burst mode, with autobuffering * enabled. Set the variables listed below to configure the BSP for * your application. * ******************************************************************************************* *LTC1407A timing with 40MHz crystal. * *10MHz, divided from 40MHz, forced to CLKIN by 1407A board. * *Horizontal scale is 6.25ns/chr or 25ns period at BCLKR * *BFSR Pin J1-20 ~~\____/~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\____/ ~~~~~~~~~~~* *BCLKR Pin J1-14 _/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/~\_/ ~\_/~\_/~* *BDR Pin J1-26 _--_--_--<B13-B12-B11-B10-B09-B08-B07-B06-B05-B04-B03-B02-B01-B00>--_--<B13- B12* *CLKIN Pin J5-09 ~~~~~\_______/~~~~~~~\_______/~~~~~~~\_______/~~~~~~~\_______/ ~~~~~~~\_______/~~~~~* *C542 read 0 B13 B12 B11 B10 B09 B08 B07 B06 B05 B04 B03 B02 B01 B00 0 0 B13 B12* * * * negative edge BCLKR * negative BFSR pulse * no data shifted * 1' cable from counter to CONV at DUT 1407fb 21 LTC1407/LTC1407A APPLICATIONS INFORMATION * 2' cable from counter to CLK at DUT *No right shift is needed to right justify the input data in the main program * *the two msbs should also be masked * ******************************************************************************************* * Loopback .set NO ;(digital looback mode?) DLB bit Format .set BIT_16 ;(Data format? 16,12,10,8) FO bit IntSync .set NO ;(internal Frame syncs generated?) TXM bit IntCLK .set NO ;(internal clks generated?) MCM bit BurstMode .set YES ;(if BurstMode=NO, then Continuous) FSM bit CLKDIV .set 3 ;(3=default value, 1/4 CLOCKOUT) PCM_Mode .set NO ;(Turn on PCM mode?) FS_polarity .set YES ;(change polarity)YES=~~~\_/~~~, NO=___/~\___ CLK_polarity .set NO ;(change polarity)for BCLKR YES=_/~, NO=~\_ Frame_ignore .set !YES ;(inverted !YES -ignores frame) XMTautobuf .set NO ;(transmit autobuffering) RCVautobuf .set NO ;(receive autobuffering) XMThalt .set NO ;(transmit buff halt if XMT buff is full) RCVhalt .set NO ;(receive buff halt if RCV buff is full) XMTbufAddr .set 0x600 ;(address of transmit buffer) RCVbufAddr .set 0x800 ;(address of receive buffer) XMTbufSize .set 0x200 ;(length of transmit buffer) RCVbufSize .set 0x040 ;(length of receive buffer) * * See notes in the `C54x CPU and Peripherals Reference Guide on setting up * valid buffer start and length values. * * ********************************************************************** .eval ((Loopback >> 1)|((Format & 2)<<1)|(BurstMode <<3)|(IntCLK <<4)|(IntSync <<5)) ,SPCval .eval ((CLKDIV)|(FS_polarity <<5)|(CLK_polarity<<6)|((Format & 1)<<7)|(Frame_ignore<<8)|(PCM_Mode<<9)), SPCEval .eval (SPCEval|(XMTautobuf<<10)|(XMThalt<<12)|(RCVautobuf<<13)|(RCVhalt<<15)), SPCEval bspi1407A: bspc = #SPCval bspce = #SPCEval axr = #XMTbufAddr bkx = #XMTbufSize arr = #RCVbufAddr bkr = #RCVbufSize bspc = #(SPCval | GO) return ; ; ; ; ; ; ; ; places buffered serial port in reset programs BSPCE and ABU initializes transmit buffer start address initializes transmit buffer size initializes receive buffer start address initializes receive buffer size bring buffered serial port out of reset for transmit and receive because GO=0xC0 1407fb 22 LTC1407/LTC1407A PACKAGE DESCRIPTION MSE Package 10-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1664 Rev C) BOTTOM VIEW OF EXPOSED PAD OPTION 2.794 p 0.102 (.110 p .004) 5.23 (.206) MIN 0.889 p 0.127 (.035 p .005) 1 0.05 REF 10 DETAIL "B" CORNER TAIL IS PART OF DETAIL "B" THE LEADFRAME FEATURE. FOR REFERENCE ONLY NO MEASUREMENT PURPOSE 3.00 p 0.102 (.118 p .004) (NOTE 3) 10 9 8 7 6 DETAIL "A" 0o - 6o TYP 1 2 3 4 5 GAUGE PLANE 0.53 p 0.152 (.021 p .006) DETAIL "A" 0.18 (.007) 0.497 p 0.076 (.0196 p .003) REF 3.00 p 0.102 (.118 p .004) (NOTE 4) 4.90 p 0.152 (.193 p .006) 0.254 (.010) 0.29 REF 1.83 p 0.102 (.072 p .004) 2.083 p 0.102 3.20 - 3.45 (.082 p .004) (.126 - .136) 0.50 0.305 p 0.038 (.0197) (.0120 p .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 2.06 p 0.102 (.081 p .004) SEATING PLANE 0.86 (.034) REF 1.10 (.043) MAX 0.17 - 0.27 (.007 - .011) TYP 0.50 (.0197) BSC 0.1016 p 0.0508 (.004 p .002) MSOP (MSE) 0908 REV C NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 1407fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 23 LTC1407/LTC1407A TYPICAL APPLICATION PART NUMBER DESCRIPTION COMMENTS LTC1608 16-Bit, 500ksps Parallel ADC 5V Supply, 2.5V Span, 90dB SINAD LTC1609 16-Bit, 250ksps Serial ADC 5V Configurable Bipolar/Unipolar Inputs ADCs LTC1403/LTC1403A 12-/14-Bit, 2.8Msps Serial ADC 3V, 15mW, MSOP Package LTC1411 14-Bit, 2.5Msps Parallel ADC 5V, Selectable Spans, 80dB SINAD LTC1420 12-Bit, 10Msps Parallel ADC 5V, Selectable Spans, 72dB SINAD LTC1405 12-Bit, 5Msps Parallel ADC 5V, Selectable Spans, 115mW LTC1412 12-Bit, 3Msps Parallel ADC 5V Supply, 2.5V Span, 72dB SINAD LTC1402 12-Bit, 2.2Msps Serial ADC 5V or 5V Supply, 4.096V or 2.5V Span LTC1864/LTC1865 LTC1864L/LTC1865L 16-Bit, 250ksps 1-/2-Channel Serial ADCs 5V or 3V (L-Version), Micropower, MSOP Package LTC1666/LTC1667 LTC1668 12-/14-/16-Bit, 50Msps DAC 87dB SFDR, 20ns Settling Time LTC1592 16-Bit, Serial SoftSpanTM IOUT DAC 1LSB INL/DNL, Software Selectable Spans LT1790-2.5 Micropower Series Reference in SOT-23 0.05% Initial Accuracy, 10ppm Drift LT1461-2.5 Precision Voltage Reference 0.04% Initial Accuracy, 3ppm Drift LT1460-2.5 Micropower Series Voltage Reference 0.10% Initial Accuracy, 10ppm Drift DACs References SoftSpan is a trademark of Linear Technology Corporation. 1407fb 24 Linear Technology Corporation LT 0109 REV B * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2003