Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4Vdc – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A Output Current
* UL is a registered trademark of Underwriters Laboratories, Inc.
† CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
Document No: DS04-020 ver. 1.22
PDF name: superlynx_II_sip_ds.pdf
Applications
Distributed power architectures
Intermediate bus voltage applications
Telecommunications equipment
Servers and storage applications
Networking equipment
Features
Compliant to RoHS EU Directive 2002/95/EC (-Z
versions)
Compliant to ROHS EU Directive 2002/95/EC with
lead solder exemption (non-Z versions)
Flexible output voltage sequencing EZ-SEQUENCE
Delivers up to 16A of output current
High efficiency – 95% at 3.3V full load (VIN = 5.0V)
Small size and low profile:
50.8 mm x 12.7 mm x 8.1 mm
(2.0 in x 0.5 in x 0.32 in)
Low output ripple and noise
Constant switching frequency (300KHz)
High Reliability:
Calculated MTBF > 11.12 M hours at 25oC Full-load
Programmable Output voltage programmable
Line Regulation: 0.3% (typical)
Load Regulation: 0.4% (typical)
Temperature Regulation: 0.4% (typical)
Remote On/Off
Remote Sense
Output overcurrent protection (non-latching)
Overtemperature protection
Wide operating temperature range (-40°C to 85°C)
UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-
03 Certified, and VDE‡ 0805:2001-12 (EN60950-1)
Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Description
Austin SuperLynxTM II SIP power modules are non-isolated dc-dc converters that can deliver up to 16A of output
current with full load efficiency of 95% at 3.3V output. These modules provide a precisely regulated output voltage
programmable via external resistor from 0.75Vdc to 3.3Vdc over a wide range of input voltage (VIN = 2.4 – 5.5Vdc).
Austin SuperLynxTM II has a sequencing feature, EZ-SEQUENCETM that enable designers to implement various
types of output voltage sequencing when powering multiple modules on board. Their open-frame construction and
small footprint enable designers to develop cost- and space-efficient solutions. In addition to sequencing, standard
features include remote On/Off, remote sense, programmable output voltage, over current and over temperature
protection.
RoHS Compliant
EZ-SEQUENCETM
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage All VIN -0.3 5.8 Vdc
Continuous
Sequencing Voltage All VSEQ -0.3 ViN, Max Vdc
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage VO,set ≤ VIN – 0.5V VIN 2.4
⎯ 5.5 Vdc
Maximum Input Current All IIN,max 16.0 Adc
(VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc)
Input No Load Current VO,set = 0.75 Vdc IIN,No load 25 mA
(VIN = 5.0Vdc, IO = 0, module enabled) VO,set = 3.3Vdc IIN,No load 40 mA
Input Stand-by Current All IIN,stand-by 1.5 mA
(VIN = 5.0Vdc, module disabled)
Inrush Transient All I2t 0.1 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN, min to
VIN, max, IO= IOmax ; See Test configuration section)
All 100 mAp-p
Input Ripple Rejection (120Hz) All 30 dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to being
part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to
achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a 20A,
fast-acting, glass type fuse rated for 32V (see Safety Considerations section). Based on the information provided in
this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be
used. Refer to the fuse manufacturer’s data sheet for further information.
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point All VO, set –2.0 ⎯ +2.0 % VO, set
(VIN=IN, min, IO=IO, max, TA=25°C)
Output Voltage All VO, set –3% ⎯ +3% % VO, set
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Adjustment Range All VO 0.7525 3.63 Vdc
Selected by an external resistor
Output Regulation
Line (VIN=VIN, min to VIN, max) All
⎯ 0.3 % VO, set
Load (IO=IO, min to IO, max) All
⎯ 0.4 % VO, set
Temperature (Tref=TA, min to TA, max) All
⎯ 0.4 % VO, set
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max
Cout = 1μF ceramic//10μFtantalum capacitors)
RMS (5Hz to 20MHz bandwidth) All ⎯ 8 15 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ 25 50 mVpk-pk
External Capacitance
ESR ≥ 1 mΩ All CO, max ⎯ ⎯ 1000 μF
ESR ≥ 10 mΩ All CO, max ⎯ ⎯ 5000 μF
Output Current All Io 0 ⎯ 16 Adc
Output Current Limit Inception (Hiccup Mode ) All IO, lim ⎯ 180 ⎯ % Io
Output Short-Circuit Current All IO, s/c ⎯ 3.5 ⎯ Adc
(VO≤250mV) ( Hiccup Mode )
Efficiency VO,set = 0.75Vdc η 82.0 %
VIN= VIN, nom, TA=25°C VO, set = 1.2Vdc η 87.0 %
IO=IO, max , VO= VO,set V
O,set = 1.5Vdc η 89.0 %
V
O,set = 1.8Vdc η 90.0 %
V
O,set = 2.5Vdc η 92.5 %
V
O,set = 3.3Vdc η 95.0 %
Switching Frequency All fsw ⎯ 300 ⎯ kHz
Dynamic Load Response
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 300 ⎯ mV
Load Change from Io= 50% to 100% of
Io,max; 1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 25 ⎯ μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 300 ⎯ mV
Load Change from Io= 100% to 50%of Io,max:
1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 25 ⎯ μs
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIPNon-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output
LINEAGE POWER 4
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Dynamic Load Response
(dIo/dt=2.5A/μs; V VIN = VIN, nom; TA=25°C) All Vpk ⎯ 150 ⎯ mV
Load Change from Io= 50% to 100% of Io,max;
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 100 ⎯ μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) All Vpk ⎯ 150 ⎯ mV
Load Change from Io= 100% to 50%of Io,max:
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts ⎯ 100 ⎯ μs
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (IO=IO, max, TA=25°C) 11,112,600 Hours
Telecordia SR-332 Issue 1: Method 1 Case 3
Weight ⎯ 5.6 (0.2) ⎯ g (oz.)
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 5
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
On/Off Signal interface
Device code with Suffix “4” – Positive logic
(On/Off is open collector/drain logic input;
Signal referenced to GND - See feature description
section)
Input High Voltage (Module ON) All VIH ― ― V
IN, max V
Input High Current All IIH ― ― 10 μA
Input Low Voltage (Module OFF) All VIL -0.2 ― 0.3 V
Input Low Current All IIL ― 0.2 1 mA
Device Code with no suffix – Negative Logic
(On/OFF pin is open collector/drain logic input with
external pull-up resistor; signal referenced to GND)
Input High Voltage (Module OFF) All VIH 1.5 ― V
IN,max Vdc
Input High Current All IIH 0.2 1 mA
Input Low Voltage (Module ON) All VIL -0.2 ― 0.3 Vdc
Input low Current All IIL ― 10 μA
Turn-On Delay and Rise Times
(IO=IO, max , VIN = VIN, nom, TA = 25 oC, )
Case 1: On/Off input is set to Logic Low (Module
ON) and then input power is applied (delay from
instant at which VIN =VIN, min until Vo=10% of Vo,set)
All Tdelay 3.9 msec
Case 2: Input power is applied for at least one second
and then the On/Off input is set to logic Low (delay from
instant at which Von/Off=0.3V until Vo=10% of Vo, set)
All Tdelay 3.9 msec
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
All Trise ― 4.2 8.5 msec
Output voltage overshoot – Startup ― 1 % VO, set
IO= IO, max; VIN = VIN, min to VIN, max, TA = 25 oC
Sequencing Delay time
Delay from VIN, min to application of voltage on SEQ pin All TsEQ-delay 10 msec
Tracking Accuracy (Power-Up: 2V/ms) All |VSEQ –Vo | 100 200 mV
(Power-Down: 1V/ms) All |VSEQ –Vo | 200 400 mV
(VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo)
Remote Sense Range All ― ― 0.5 V
Overtemperature Protection All Tref ⎯ 125 ⎯ °C
(See Thermal Consideration section)
Input Undervoltage Lockout
Turn-on Threshold All ⎯ 2.2 ⎯ V
Turn-off Threshold All ⎯ 2.0 ⎯ V
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 6
Characteristic Curves
The following figures provide typical characteristics for the Austin SuperLynxTM II SIP modules at 25ºC.
72
75
78
81
84
87
90
04 81216
VIN = 5.5V
VIN = 5.0V
VIN = 3.0V
72
75
78
81
84
87
90
93
96
0481216
VIN = 5.5V
VIN = 5.0V
VIN = 3.0V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 1. Converter Efficiency versus Output Current
(Vout = 0.75Vdc).
Figure 4. Converter Efficiency versus Output Current
(Vout = 1.8Vdc).
72
75
78
81
84
87
90
93
0 4 8 12 16
VIN = 5.5V
VIN = 5.0V
VIN = 3.0V
73
76
79
82
85
88
91
94
97
10 0
04 81216
VIN = 5.5V
VIN = 5.0V
VIN = 3.0V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 2. Converter Efficiency versus Output Current
(Vout = 1.2Vdc).
Figure 5. Converter Efficiency versus Output Current
(Vout = 2.5Vdc).
70
73
76
79
82
85
88
91
94
0481216
VIN = 5.5V
VIN = 5.0V
VIN = 3.0V
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
Figure 3. Converter Efficiency versus Output Current
(Vout = 1.5Vdc).
Figure 6. Converter Efficiency versus Output Current
(Vout = 3.3Vdc).
76
79
82
85
88
91
94
97
10 0
0 4 8 12 16
VIN = 5.5V
VIN = 5.0V
VIN = 4.5V
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 7
Characteristic Curves (continued)
The following figures provide typical characteristics for the Austin SuperLynxTM II SIP modules at 25ºC.
0
2
4
6
8
10
12
14
16
18
0.51.52.53.54.55.5
Io =0A
Io =16A
Io =8A
INPUT CURRENT, IIN (A)
INPUT VOLTAGE, VIN
(
V
)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (5A/div) VO (V) (200mV/div)
TIME
,
t
(
5
μ
s/div
)
Figure 7. Input voltage vs. Input Current
(Vout = 2.5Vdc).
Figure 10. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 3.3Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
TIME, t (2μs/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (5A/div) VO (V) (200mV/div)
TIME, t (5 μs/div)
Figure 8. Typical Output Ripple and Noise
(Vin = 5.0V dc, Vo = 0.75 Vdc, Io=16A).
Figure 11. Transient Response to Dynamic Load
Change from 100% to 50% of full load (Vo = 3.3 Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
TIME, t (2μs/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (5A/div) VO (V) (200mV/div)
TIME, t (10μs/div)
Figure 9. Typical Output Ripple and Noise
(Vin = 5.0V dc, Vo = 3.3 Vdc, Io=16A).
Figure 12. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 5.0 Vdc,
Cext = 2x150 μF Polymer Capacitors).
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 8
Characteristic Curves (continued)
The following figures provide typical characteristics for the Austin SuperLynxTM II SIP modules at 25ºC.
OUTPUT CURRENT, OUTPUTVOLTAGE
IO (A) (5A/div) VO (V) (200mV/div)
TIME, t (10μs/div)
OUTPUT VOLTAGE INPUT VOLTAGE
VOV) (1V/div) VNN (V) (2V/div)
TIME, t (2 ms/div)
Figure 13. Transient Response to Dynamic Load
Change from 100% of 50% full load (Vo = 5.0 Vdc, Cext
= 2x150
μ
F Pol
y
mer Ca
p
acitors
)
.
Figure 16. Typical Start-Up with application of Vin
(Vin = 5.0Vdc, Vo = 3.3Vdc, Io = 16A).
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (1V/div) VOn/off (V) (2V/div)
TIME, t (2 ms/div)
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (1V/div) VOn/off (V) (2V/div)
TIME, t (2 ms/div)
Figure 14. Typical Start-Up Using Remote On/Off (Vin
= 5.0Vdc, Vo = 3.3Vdc, Io = 16.0A).
Figure 17 Typical Start-Up Using Remote On/Off with
Prebias (Vin = 3.3Vdc, Vo = 1.8Vdc, Io = 1.0A, Vbias
=1.0Vdc).
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (1V/div) VOn/off (V) (2V/div)
TIME, t (2 ms/div)
OUTPUT CURRENT,
IO (A) (10A/div)
TIME, t (10ms/div)
Figure 15. Typical Start-Up Using Remote On/Off with
Low-ESR external capacitors (Vin = 5.5Vdc, Vo =
3.3Vdc, Io = 16.0A, Co = 1050μF).
Figure 18. Output short circuit Current (Vin = 5.0Vdc,
Vo = 0.75Vdc).
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 9
Characteristic Curves (continued)
The following figures provide thermal derating curves for the Austin SuperLynxTM II SIP modules.
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
10 0 L F M
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 19. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 5.0,
Vo=3.3Vdc).
Figure 22. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 3.3dc,
Vo=0.75 Vdc).
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 20. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 5.0Vdc,
Vo=0.75 Vdc).
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 21. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 3.3Vdc,
Vo=2.5 Vdc).
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 10
Test Configurations
TO OSCILLOSCOPE CURRENT PROBE
LTEST
1μH
BATTERY
CS 1000μF
Electrolytic
E.S.R.<0.1Ω
@ 20°C 100kHz
2x100μF
Tantalum
VIN(+)
COM
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
CIN
Figure 23. Input Reflected Ripple Current Test Setup.
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
V
O
(+)
COM
1uF .
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
Figure 24. Output Ripple and Noise Test Setup.
VO
COM
VIN(+)
COM
RLOAD
Rcontact Rdistribution
Rcontact Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
VIN VO
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 25. Output Voltage and Efficiency Test Setup.
η =
VO. IO
VIN. IIN
x 100 %
Efficiency
Design Considerations
Input Filtering
The Austin SuperLynxTM SIP module should be
connected to a low-impedance source. A highly inductive
source can affect the stability of the module. An input
capacitance must be placed directly adjacent to the input
pin of the module, to minimize input ripple voltage and
ensure module stability.
To minimize input voltage ripple, low-ESR polymer and
ceramic capacitors are recommended at the input of the
module. Figure 26 shows the input ripple voltage (mVp-
p) for various outputs with 1x150 µF polymer capacitors
(Panasonic p/n: EEFUE0J151R, Sanyo p/n: 6TPE150M)
in parallel with 1 x 47 µF ceramic capacitor (Panasonic
p/n: ECJ-5YB0J476M, Taiyo- Yuden p/n:
CEJMK432BJ476MMT) at full load. Figure 27 shows the
input ripple with 2x150 µF polymer capacitors in parallel
with 2 x 47 µF ceramic capacitor at full load.
Input Ripple Voltage (mVp-p)
0
50
100
150
200
250
300
0.511.522.533.5
3.3Vin
5Vin
Output Voltage (Vdc)
Figure 26. Input ripple voltage for various output
with 1x150 µF polymer and 1x47 µF ceramic
capacitors at the input (full load).
Input Ripple Voltage (mVp-p)
0
20
40
60
80
100
120
140
160
180
200
0.51 1.522.53 3.5
3.3Vin
5Vin
Output Voltage (Vdc)
Figure 27. Input ripple voltage for various output
with 2x150 µF polymer and 2x47 µF ceramic
capacitors at the input (full load).
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 11
Design Considerations (continued)
Output Filtering
The Austin SuperLynxTM II SIP module is designed for low
output ripple voltage and will meet the maximum output
ripple specification with 1 µF ceramic and 10 µF tantalum
capacitors at the output of the module. However,
additional output filtering may be required by the system
designer for a number of reasons. First, there may be a
need to further reduce the output ripple and noise of the
module. Second, the dynamic response characteristics
may need to be customized to a particular load step
change.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance at
the output can be used. Low ESR polymer and ceramic
capacitors are recommended to improve the dynamic
response of the module. For stable operation of the
module, limit the capacitance to less than the maximum
output capacitance as specified in the electrical
specification table.
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE
0850:2001-12 (EN60950-1) Licensed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
The input to these units is to be provided with a fast-
acting fuse with a maximum rating of 20A in the positive
input lead.
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 12
Feature Description
Remote On/Off
Austin SuperLynxTM II SIP power modules feature an
On/Off pin for remote On/Off operation. Two On/Off logic
options are available in the Austin SuperLynxTM II series
modules. Positive Logic On/Off signal, device code suffix
“4”, turns the module ON during a logic High on the
On/Off pin and turns the module OFF during a logic Low.
Negative logic On/Off signal, no device code suffix, turns
the module OFF during logic High and turns the module
ON during logic Low.
For positive logic modules, the circuit configuration for
using the On/Off pin is shown in Figure 28. The On/Off
pin is an open collector/drain logic input signal (Von/Off)
that is referenced to ground. During a logic-high (On/Off
pin is pulled high internal to the module) when the
transistor Q1 is in the Off state, the power module is ON.
Maximum allowable leakage current of the transistor
when Von/off = VIN,max is 10µA. Applying a logic-low
when the transistor Q1 is turned-On, the power module is
OFF. During this state VOn/Off must be less than 0.3V.
When not using positive logic On/off pin, leave the pin
unconnected or tie to VIN.
Q1
R2
R1
Q2
R3
R4
Q3 CSS
GND
VIN+
ON/OFF
PWM Enable
+
_
ON/OFF
V
ION/OFF
MODULE
Figure 28. Remote On/Off Implementation.
For negative logic On/Off devices, the circuit
configuration is shown is Figure 29. The On/Off pin is
pulled high with an external pull-up resistor (typical Rpull-
up = 68k, +/- 5%). When transistor Q1 is in the Off state,
logic High is applied to the On/Off pin and the power
module is Off. The minimum On/off voltage for logic High
on the On/Off pin is 1.5Vdc. To turn the module ON,
logic Low is applied to the On/Off pin by turning ON Q1.
When not using the negative logic On/Off, leave the pin
unconnected or tie to GND.
Q1
R1
R2
Q2 CSS
GND
PWM Enable
ON/OFF
VIN+
ON/OFF
_
+
V
I
MODULE
pull-up
R
ON/OFF
Figure 29. Circuit configuration for using negative
logic On/OFF
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally once
the output current is brought back into its specified range.
The typical average output current during hiccup is 3.5A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will begin
to operate at an input voltage above the undervoltage
lockout turn-on threshold.
Overtemperature Protection
To provide over temperature protection in a fault
condition, the unit relies upon the thermal protection
feature of the controller IC. The unit will shutdown if the
thermal reference point Tref, exceeds 125oC (typical), but
the thermal shutdown is not intended as a guarantee that
the unit will survive temperatures beyond its rating. The
module will automatically restart after it cools down.
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 13
Feature Descriptions (continued)
Output Voltage Programming
The output voltage of the Austin SuperLynxTM II SIP can
be programmed to any voltage from 0.75 Vdc to 3.3 Vdc
by connecting a single resistor (shown as Rtrim in Figure
30) between the TRIM and GND pins of the module.
Without an external resistor between TRIM pin and the
ground, the output voltage of the module is 0.7525 Vdc.
To calculate the value of the resistor Rtrim for a particular
output voltage Vo, use the following equation:
Ω
⎥
⎦
⎤
⎢
⎣
⎡−
−
=5110
7525.0
21070
Vo
Rtrim
For example, to program the output voltage of the Austin
SuperLynxTM module to 1.8 Vdc, Rtrim is calculated is
follows:
⎥
⎦
⎤
⎢
⎣
⎡−
−
=5110
7525.08.1
21070
Rtrim
Ω= kRtrim 004.15
V
O
(+)
TRIM
GND
R
trim
LOAD
V
IN
(+)
ON/OFF
Vout
Figure 30. Circuit configuration for programming
output voltage using an external resistor.
Table 1 provides Rtrim values required for some common
output voltages
Table 1
VO, set (V) Rtrim (KΩ)
0.7525 Open
1.2 41.973
1.5 23.077
1.8 15.004
2.5 6.947
3.3 3.160
By using a 1% tolerance trim resistor, set point tolerance
of ±2% is achieved as specified in the electrical
specification. The POL Programming Tool, available at
www.lineagepower.com under the Design Tools section,
helps determine the required external trim resistor
needed for a specific output voltage.
The amount of power delivered by the module is defined
as the voltage at the output terminals multiplied by the
output current. When using the trim feature, the output
voltage of the module can be increased, which at the
same output current would increase the power output of
the module. Care should be taken to ensure that the
maximum output power of the module remains at or
below the maximum rated power (Pmax = Vo,set x Io,max).
Voltage Margining
Output voltage margining can be implemented in the
Austin SuperLynxTM II modules by connecting a resistor,
Rmargin-up, from the Trim pin to the ground pin for
margining-up the output voltage and by connecting a
resistor, Rmargin-down, from the Trim pin to the Output pin
for margining-down. Figure 31 shows the circuit
configuration for output voltage margining. The POL
Programming Tool, available at www.lineagepower.com
under the Design Tools section, also calculates the
values of Rmargin-up and Rmargin-down for a specific output
voltage and % margin. Please consult your local Lineage
Power technical representative for additional details.
Vo
Austin Lynx or
Lynx II Series
GND
Trim
Q1
Rtrim
Rmargin-up
Q2
Rmargin-down
Figure 31. Circuit Configuration for margining Output
voltage.
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 14
Feature Descriptions (continued)
Voltage Sequencing
Austin SuperLynxTM II series of modules include a
sequencing feature, EZ-SEQUENCE that enables users
to implement various types of output voltage sequencing
in their applications. This is accomplished via an
additional sequencing pin. When not using the
sequencing feature, either tie the SEQ pin to VIN or leave
it unconnected.
When an analog voltage is applied to the SEQ pin, the
output voltage tracks this voltage until the output reaches
the set-point voltage. The SEQ voltage must be set
higher than the set-point voltage of the module. The
output voltage follows the voltage on the SEQ pin on a
one-to-one volt basis. By connecting multiple modules
together, customers can get multiple modules to track
their output voltages to the voltage applied on the SEQ
pin.
For proper voltage sequencing, first, input voltage is
applied to the module. The On/Off pin of the module is
left unconnected (or tied to GND for negative logic
modules or tied to VIN for positive logic modules) so that
the module is ON by default. After applying input voltage
to the module, a minimum of 10msec delay is required
before applying voltage on the SEQ pin. During this time,
potential of 50mV (± 10 mV) is maintained on the SEQ
pin. After 10msec delay, an analog voltage is applied to
the SEQ pin and the output voltage of the module will
track this voltage on a one-to-one volt bases until output
reaches the set-point voltage. To initiate simultaneous
shutdown of the modules, the SEQ pin voltage is lowered
in a controlled manner. Output voltage of the modules
tracks the voltages below their set-point voltages on a
one-to-one basis. A valid input voltage must be
maintained until the tracking and output voltages reach
ground potential.
When using the EZ-SEQUENCETM feature to control
start-up of the module, pre-bias immunity feature during
start-up is disabled. The pre-bias immunity feature of the
module relies on the module being in the diode-mode
during start-up. When using the EZ-SEQUENCETM
feature, modules goes through an internal set-up time of
10msec, and will be in synchronous rectification mode
when voltage at the SEQ pin is applied. This will result in
sinking current in the module if pre-bias voltage is present
at the output of the module. When pre-bias immunity
during start-up is required, the EZ-SEQUENCETM feature
must be disabled. For additional guidelines on using EZ-
SEQUENCETM feature of Austin SuperLynxTM II, contact
the Lineage Power technical representative for
preliminary application note on output voltage sequencing
using Austin Lynx II series.
Remote Sense
The Austin SuperLynxTM SIP power modules have a
Remote Sense feature to minimize the effects of
distribution losses by regulating the voltage at the
Remote Sense pin (See Figure 32). The voltage between
the Sense pin and Vo pin must not exceed 0.5V.
The amount of power delivered by the module is defined
as the output voltage multiplied by the output current (Vo
x Io). When using Remote Sense, the output voltage of
the module can increase, which if the same output is
maintained, increases the power output by the module.
Make sure that the maximum output power of the module
remains at or below the maximum rated power. When
the Remote Sense feature is not being used, connect the
Remote Sense pin to the output pin.
VO
COM
VIN(+ )
COM
RLOAD
Rcontact Rdistribution
Rcontact Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
Sense
Figure 32. Remote sense circuit configuration
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 15
Thermal Considerations
Power modules operate in a variety of thermal
environments; however, sufficient cooling should always
be provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of the
module will result in an increase in reliability. The thermal
data presented here is based on physical measurements
taken in a wind tunnel. The test set-up is shown in Figure
34. Note that the airflow is parallel to the long axis of the
module as shown in figure 33. The derating data applies
to airflow in either direction of the module’s long axis.
Airflow
Tref
Top View
Figure 33. Tref Temperature measurement location.
The thermal reference point, Tref used in the
specifications is shown in Figure 33. For reliable
operation this temperature should not exceed 115oC.
The output power of the module should not exceed the
rated power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-
Mounted Power Modules” for a detailed discussion of
thermal aspects including maximum device temperatures.
Figure 34. Thermal Test Set-up.
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Thermal derating curves showing
the maximum output current that can be delivered at
different local ambient temperatures (TA) for airflow
conditions ranging from natural convection and up to
2m/s (400 ft./min) are shown in the Characteristics
Curves section.
A
ir
flow
x
Po w e r M o d u le
W
ind Tunne l
PWBs
5.97_
(0.235)
76.2_
(3.0)
Probe Location
for measuring
airflow and
ambient
temperature
25.4_
(1.0)
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 16
Post solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect both
the reliability of a power module and the testability of the
finished circuit-board assembly. For guidance on
appropriate soldering, cleaning and drying procedures,
refer to Board Mounted Power Modules: Soldering and
Cleaning Application Note.
Through-Hole Lead-Free Soldering
Information
The RoHS-compliant through-hole products use the SAC
(Sn/Ag/Cu) Pb-free solder and RoHS-compliant
components. They are designed to be processed
through single or dual wave soldering machines. The
pins have an RoHS-compliant finish that is compatible
with both Pb and Pb-free wave soldering processes. A
maximum preheat rate of 3°C/s is suggested. The wave
preheat process should be such that the temperature of
the power module board is kept below 210°C. For Pb
solder, the recommended pot temperature is 260°C, while
the Pb-free solder pot is 270°C max. Not all RoHS-
compliant through-hole products can be processed with
paste-through-hole Pb or Pb-free reflow process. If
additional information is needed, please consult with your
Lineage Power technical representative for more details.
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 17
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Top View
Side View
Back View
PIN FUNCTION
1 Vo
2 Vo
3 Sense+
4 Vo
5 GND
6 GND
7 VIN
8 VIN
B SEQ
9 Trim
10 On/Off
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 18
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm ( x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm ( x.xxx in ± 0.010 in.)
PIN FUNCTION
1 Vo
2 Vo
3 Sense+
4 Vo
5 GND
6 GND
7 VIN
8 VIN
B SEQ
9 Trim
10 On/Off
Module Layout – Back view
Data Sheet
October 2, 2009
Austin SuperlynxTM II SIP Non-isolated Power Modules:
2.4 – 5.5Vdc input; 0.75Vdc to 3.3Vdc Output; 16A output current
LINEAGE POWER 19
Document No: DS04-020 ver. 1.22
PDF name: superlynx_II_sip_ds.pdf
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 2. Device Codes
Product codes Input Voltage Output Voltage Output
Current
Efficiency
3.3V @ 16A
Connector
Type Comcodes
ATH016A0X3 2.4 – 5.5Vdc 0.75 – 3.3Vdc 16A 95.0% SIP
108989117
ATH016A0X3Z 2.4 – 5.5Vdc 0.75 – 3.3Vdc 16A 95.0% SIP CC109104758
ATH016A0X43 2.4 – 5.5Vdc 0.75 – 3.3Vdc 16A 95.0% SIP 108989125
ATH016A0X43Z 2.4 – 5.5Vdc 0.75 – 3.3Vdc 16A 95.0% SIP CC109104766
-Z refers to RoHS-compliant versions.
World Wide Headquarters
Lineage Power Corporation
601 Shiloh Road, Plano, TX 75074, USA
+1-800-526-7819
(Outside U.S.A.: +1-972-244-9428)
www.lineagepower.com
e-mail: techsupport1@lineagepower.com
Asia-Pacific Headquarters
Tel: +65 6593 7211
Europe, Middle-East and Africa Headquarters
Tel: +49 898 780 672 80
India Headquarters
Tel: +91 80 28411633
Lineage Power reserves the right to make change s to the p roduct(s) or information contained herein without notice. No liability is assumed as a result of their use or
a
pplication. No rights under any patent accompany the sale of any such product(s) or information.
Lineage Power DC-DC products are protected unde r various patents. Information on these patents is available at www.lineagepower.com/patents.
©
2009 Linea
g
e Power Cor
p
oration
,
(
Plano
,
Texas
)
All Inte rnational Ri
g
hts Reserved.
