TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
1/8
Version: D13
TO
-
252
(DPAK)
General Description
The TS78M00 Series positive voltage regulators are identical to the popular TS7800 Series devices, except that
they are specified for only half the output current. Like the TS7800 devices, the TS78M00 Series 3-Terminal
regulators are intended for local, on-card voltage regulation.
Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor
combine to make these devices remarkably rugged under most operating conditions. Maximum output current with
adequate heatsink is 500mA
Features
Output Voltage Range 5 to 24V
Output current up to 500mA
No external components required
Internal thermal overload protection
Internal short-circuit current limiting
Output transistor safe-area compensation
Output voltage offered in 4% tolerance
Standard Application Circuit
A common ground is required between the input and the
output voltages. The input voltage must remain typically
2.0V above the output voltage even during the low point
on the Input ripple voltage.
XX = these two digits of the type number indicate voltage.
* = Cin is required if regulator is located an appreciable
distance from power supply filter.
** = Co is not needed for stability; however, it does
improve transient response.
Ordering Information
Part No. Package
Packing
TS78MxxCP RO TO-252 2.5Kpcs / 13” Reel
TS78MxxCP ROG TO-252 2.5Kpcs / 13” Reel
Note: “G” denotes Halogen Free Product.
Note: Where xx denote voltage option, available are:
05=5V, 08=9V, 09=9V, 12=12V, 15=15V,
18=18V, 24=24V
Absolute Maximum Rating
(Ta = 25
o
C unless otherwise noted)
Parameter Symbol Limit Unit
Input Voltage V
IN
* 35 V
Input Voltage V
IN
** 40 V
Power Dissipation P
D
Internal Limited W
Operating Junction Temperature T
J
0~+125
o
C
Storage Temperature Range T
STG
-65~+150
o
C
Thermal Resistance - Junction to Case RӨ
JC
10
o
C/W
Thermal Resistance - Junction to Ambient RӨ
JA
100
o
C/W
Note: * TS78M05 to TS78M18
** TS78M24
*** Follow the derating curve
Pin
:
1. Input
2. Ground (tab)
3. Output
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
2/8
Version: D13
TS78M05 Electrical Characteristics
(Vin=10V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output voltage Vout Tj=25
o
C 4.80 5 5.20 V
7.5VVin20V,
5mAIout350mA 4.75 5 5.25
Line Regulation REGline Tj=25
o
C
7.5VVin25V -- 3 100
mV
8VVin12V -- 1 50
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 15 100
5mAIout200mA -- 5 50
Quiescent Current Iq Iout=0, Tj=25
o
C -- 3 6 mA
Quiescent Current Change Iq 7.5VVin25V -- -- 0.8
5mAIout350mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 40 -- µV
Ripple Rejection Ratio RR f=120Hz, 8VVin18V 62 78 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 17 -- m
Output Short Circuit Current
Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout= 5mA, 0
o
CTj125
o
C -- -0.2 -- mV/
o
C
TS78M08 Electrical Characteristics
Vin=14V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output voltage Vout Tj=25
o
C 7.69 8 8.32 V
10.5VVin23V,
5mAIout350mA 7.61 8 8.40
Line Regulation REGline Tj=25
o
C
10.5VVin25V -- 6 160
mV
11VVin17V -- 2 80
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 160
5mAIout200mA -- 4 80
Quiescent Current Iq Iout=0, Tj=25
o
C -- 3 6 mA
Quiescent Current Change Iq 10.5VVin25V -- -- 0.8
5mAIout350mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 52 -- µV
Ripple Rejection Ratio RR f=120Hz, 11VVin21V 56 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 16 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout= 5mA, 0
o
CTj125
o
C -- -0.2 -- mV/
o
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
3/8
Version: D13
TS78M09 Electrical Characteristics
(Vin=15V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output Voltage Vout Tj=25
o
C 8.65 9 9.36 V
11.5VVin23V,
5mAIout350mA 8.57 9 9.45
Line Regulation REGline Tj=25
o
C
11.5VVin26V -- 6 180
mV
12VVin17V -- 2 90
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 180
5mAIout200mA -- 4 90
Quiescent Current Iq Iout=0, Tj=25
o
C -- 3 6 mA
Quiescent Current Change Iq 11.5VVin26V -- -- 0.8
5mAIout350mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 52 -- uV
Ripple Rejection Ratio RR f=120Hz, 12VVin22V 55 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 16 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout= 5mA, 0
o
CTj125
o
C -- -0.2 -- mV/
o
C
TS78M12 Electrical Characteristics
(Vin=19V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output Voltage Vout Tj=25
o
C 11.53
12 12.48
V
14.5VVin27V,
5mAIout350mA 11.42
12 12.60
Line Regulation REGline Tj=25
o
C
14.5VVin30V -- 10 240
mV
15VVin19V -- 3 120
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 240
5mAIout200mA -- 4 120
Quiescent Current Iq Tj=25
o
C, Iout=0 -- 3 6 mA
Quiescent Current Change Iq 14.5VVin30V -- -- 0.8
5mAIout500mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 75 -- uV
Ripple Rejection Ratio RR f=120Hz, 15VVin25V 55 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 18 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout=5mA, 0
o
CTj125
o
C -- -0.3 -- mV/
o
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
4/8
Version: D13
TS78M15 Electrical Characteristics
(Vin=23V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output voltage Vout Tj=25
o
C 14.42
15 15.60
V
17.5VVin30V,
5mAIout350mA 14.28
15 15.75
Line Regulation REGline Tj=25
o
C
17.5VVin30V -- 12 300
mV
18VVin22V -- 3 150
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 300
5mAIout200mA -- 4 150
Quiescent Current Iq Tj=25
o
C, Iout=0 -- 3 6 mA
Quiescent Current Change Iq 17.5VVin30V -- -- 0.8
5mAIout500mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 90 -- µV
Ripple Rejection Ratio RR f=120Hz, 18VVin28V 54 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 19 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout=10mA, 0
o
CTj125
o
C -- -0.3 -- mV/
o
C
TS78M18 Electrical Characteristics
(Vin=24V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output Voltage Vout Tj=25
o
C 17.30
18 18.72
V
21VVin33V,
5mAIout350mA 17.14
18 18.90
Line Regulation REGline Tj=25
o
C
21VVin33V -- 15 360
mV
22VVin26V -- 5 180
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 360
5mAIout200mA -- 4 180
Quiescent Current Iq Tj=25
o
C, Iout=0 -- 3 6 mA
Quiescent Current Change Iq 21VVin33V -- -- 0.8
5mAIout500mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 110 -- uV
Ripple Rejection Ratio RR f=120Hz, 21VVin31V 54 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 22 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout= 5mA, 0
o
CTj125
o
C -- -0.5 -- mV/
o
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
5/8
Version: D13
TS78M24 Electrical Characteristics
Vin=33V, Iout=350mA, 0
o
CTj125
o
C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.)
Parameter Symbol Test Condition Min Typ Max Unit
Output voltage Vout Tj=25
o
C 23.07
24 24.96
V
27VVin38V,
5mAIout350mA 22.85
24 25.20
Line Regulation REGline Tj=25
o
C
27VVin38V -- 18 480
mV
28VVin32V -- 6 240
Load Regulation REGload Tj=25
o
C
5mAIout500mA -- 12 480
5mAIout200mA -- 4 240
Quiescent Current Iq Iout=0, Tj=25
o
C -- 3 6 mA
Quiescent Current Change Iq 27VVin38V -- -- 0.8
5mAIout500mA -- -- 0.5
Output Noise Voltage Vn 10Hzf100KHz, Tj=25
o
C -- 170 -- µV
Ripple Rejection Ratio RR f=120Hz, 27VVin37V 54 80 -- dB
Voltage Drop Vdrop Iout=500mA, Tj=25
o
C -- 2 -- V
Output Resistance Rout f=1KHz -- 28 -- m
Output Short Circuit Current Ios Tj=25
o
C -- 50 -- mA
Peak Output Current Io peak Tj=25
o
C -- 0.7 -- A
Temperature Coefficient of
Output Voltage Vout/ Tj
Iout= 5mA, 0
o
CTj125
o
C -- -0.5 -- mV/
o
C
Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as
possible, and thermal effects must be taken into account separately.
This specification applies only for DC power dissipation permitted by absolute maximum ratings.
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
6/8
Version: D13
Electrical Characteristics Curve
Figure 1. Bias Current vs. Input Voltage
Figure 2. Dropout Voltage vs.
Junction Temperature
Figure 3. Bias Current vs. Output Current
Figure 4. Ripple Rejection vs. Frequency
Figure 6. Peak Output Current vs. Dropout
Voltage
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
7/8
Version: D13
TO-252 Mechanical Drawing
Unit: Millimeters
Marking Diagram
XX
= Output Voltage
(05=5V, 08=8V, 09=9V, 12=12V, 15=15V, 18=18V, 24=24V)
Y
= Year Code
M
= Month Code
(A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep,
J=Oct, K=Nov, L=Dec)
= Month Code for Halogen Free Product
(O=Jan, P=Feb, Q=Mar, R=Apl, S=May, T=Jun, U=Jul, V=Aug, W=Sep,
X=Oct, Y=Nov, Z=Dec)
L
= Lot Code
CP
= Package Code for TO
-252
TS78M00 Series
3-Terminal 500mA Positive Voltage Regulator
8/8
Version: D13
Notice
Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf,
assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, to
any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of
sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty,
relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose,
merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify TSC for any damages resulting from such improper use or sale.