SM72482 SM72482 SolarMagic Dual 5A Compound Gate Driver Literature Number: SNVS696B SM72482 SolarMagic Dual 5A Compound Gate Driver General Description The SM72482 Dual Gate Driver replaces industry standard gate drivers with improved peak output current and efficiency. Each "compound" output driver stage includes MOS and bipolar transistors operating in parallel that together sink more than 5A peak from capacitive loads. Combining the unique characteristics of MOS and bipolar devices reduces drive current variation with voltage and temperature. Under-voltage lockout protection is also provided. The drivers can be operated in parallel with inputs and outputs connected to double the drive current capability. This device is available in the SOIC-8 package. Features Renewable Energy Grade Independently drives two N-Channel MOSFETs Compound CMOS and bipolar outputs reduce output Fast rise and fall times (14 ns/12 ns rise/fall with 2 nF load) Available in dual non-inverting, dual inverting and combination configurations Supply rail under-voltage lockout protection (UVLO) SM72482 UVLO configured to drive PFET through OUT_A and NFET through OUT_B Pin compatible with industry standard gate drivers Typical Applications Synchronous Rectifier Gate Drivers Switch-mode Power Supply Gate Driver Solenoid and Motor Drivers Packages SOIC-8 Thermally Enhanced MSOP8-EP current variation 5A sink/3A source current capability Two channels can be connected in parallel to double the drive current Independent inputs (TTL compatible) Fast propagation times (25 ns typical) Connection Diagram 30142201 SOIC-8, eMSOP-8 (c) 2011 National Semiconductor Corporation 301422 www.national.com SM72482 SolarMagic Dual 5A Compound Gate Driver May 9, 2011 SM72482 Ordering Information Package Type NSC Package Drawing Package Marking SM72482MY-1 Order Number MSOP-8-EP MUY08A SD8B Supplied As 1000 Units in Tape and Reel SM72482MYE-1 MSOP-8-EP MUY08A SD8B 250 Units in Tape and Reel SM72482MYX-1 MSOP-8-EP MUY08A SD8B 3500 Units in Tape and Reel SM72482MA-4 SOIC-8 M08A S482 95 Units in Rail SM72482MAE-4 SOIC-8 M08A S482 250 Units in Tape and Reel SM72482MAX-4 SOIC-8 M08A S482 2500 Units in Tape and Reel Pin Descriptions Pin Name Description Application Information 1 NC No Connect 2 IN_A `A' side control input TTL compatible thresholds. 3 VEE Ground reference for both inputs and outputs Connect to power ground. 4 IN_B `B' side control input TTL compatible thresholds. 5 OUT_B Output for the `B' side driver. Voltage swing of this output is from VCC to VEE. The output stage is capable of sourcing 3A and sinking 5A. 6 VCC Positive output supply Locally decouple to VEE. 7 OUT_A. Output for the `A' side driver. Voltage swing of this output is from VCC to VEE. The output stage is capable of sourcing 3A and sinking 5A. 8 NC No Connect Configuration Table "A" Output Configuration "B" Output Configuration Package SM72482MY-1 Non-Inverting (Low in UVLO) Non-Inverting (Low in UVLO) MSOP8-EP SM72482MA-4 Inverting (High in UVLO) Non-Inverting (Low in UVLO) SOIC-8 Part Number www.national.com 2 SM72482 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC to VEE IN to VEE Storage Temperature Range, (TSTG) Maximum Junction Temperature, (TJ(max)) Operating Junction Temperature ESD Rating -0.3V to 15V -0.3V to 15V -55C to +150C +150C +125C 2kV Electrical Characteristics TJ = -40C to +125C, VCC = 12V, VEE = 0V, No Load on OUT_A or OUT_B, unless otherwise specified. Symbol Parameter Conditions Min VCC Operating Range VCC-VEE 3.5 VCCR VCC Under Voltage Lockout (rising) VCC-VEE 2.3 VCCH VCC Under Voltage Lockout Hysteresis ICC VCC Supply Current (ICC) Typ 2.9 Max Units 14 V 3.5 V 230 mV IN_A = IN_B = 0V (SM72482MY-1) 1 2 IN_A = VCC, IN_B = 0V (SM72482MA-4) 1 2 mA CONTROL INPUTS VIH Logic High VIL Logic Low VthH High Threshold 1.3 VthL Low Threshold 0.8 HYS Input Hysteresis IIL Input Current Low IN_A=IN_B=VCC -1 0.1 1 IIH Input Current High IN_A=IN_B=VCC(SM72482MY-1) 10 18 25 IN_B=VCC (SM72482MA-4) 10 18 25 IN_A=VCC (SM72482MA-4) -1 0.1 1 2.2 V 0.8 V 1.75 2.2 V 1.35 2.0 V 400 mV A OUTPUT DRIVERS ROH Output Resistance High IOUT = -10 mA (Note 2) 30 50 ROL Output Resistance Low IOUT = + 10 mA (Note 2) 1.4 2.5 ISource Peak Source Current OUTA/OUTB = VCC/2, 200 ns Pulsed Current 3 A ISink Peak Sink Current OUTA/OUTB = VCC/2, 200 ns Pulsed Current 5 A 3 www.national.com SM72482 Symbol Parameter Conditions Min Typ Max Units SWITCHING CHARACTERISTICS td1 Propagation Delay Time Low to High, IN rising (IN to OUT) CLOAD = 2 nF, see Figure 1 25 40 ns td2 Propagation Delay Time High to Low, IN falling (IN to OUT) CLOAD = 2 nF, see Figure 1 25 40 ns tr Rise Time CLOAD = 2 nF, see Figure 1 14 25 ns tf Fall Time CLOAD = 2 nF, see Figure 1 12 25 ns TJ = 150C 500 Junction to Ambient, 0 LFPM Air Flow SOIC-8 Package 170 MSOP8-EP Package 60 Junction to Case SOIC-8 Package 70 MSOP8-EP Package 4.7 LATCHUP PROTECTION AEC - Q100, Method 004 mA THERMAL RESISTANCE JA JC C/W C/W Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The output resistance specification applies to the MOS device only. The total output current capability is the sum of the MOS and Bipolar devices. Timing Waveforms 30142206 30142205 (b) (a) FIGURE 1. (a) Inverting, (b) Non-Inverting www.national.com 4 SM72482 Typical Performance Characteristics Supply Current vs Frequency Supply Current vs Capacitive Load 30142211 30142210 Rise and Fall Time vs Supply Voltage Rise and Fall Time vs Temperature 30142212 30142213 5 www.national.com SM72482 Rise and Fall Time vs Capacitive Load Delay Time vs Supply Voltage 30142214 30142215 Delay Time vs Temperature RDSON vs Supply Voltage 30142217 30142216 UVLO Thresholds and Hysteresis vs Temperature 30142218 www.national.com 6 SM72482 Block Diagram 30142203 Block Diagram of SM72482 7 www.national.com SM72482 Detailed Operating Description Layout Considerations The SM72482 dual gate driver consists of two independent and identical driver channels with TTL compatible logic inputs and high current totem-pole outputs that source or sink current to drive MOSFET gates. The driver output consist of a compound structure with MOS and bipolar transistor operating in parallel to optimize current capability over a wide output voltage and operating temperature range. The bipolar device provides high peak current at the critical threshold region of the MOSFET VGS while the MOS devices provide rail-to-rail output swing. The totem pole output drives the MOSFET gate between the gate drive supply voltage VCC and the power ground potential at the VEE pin. The control inputs of the drivers are high impedance CMOS buffers with TTL compatible threshold voltages. The SM72482 pinout was designed for compatibility with industry standard gate drivers in single supply gate driver applications. The input stage of each driver should be driven by a signal with a short rise and fall time. Slow rising and falling input signals, although not harmful to the driver, may result in the output switching repeatedly at a high frequency. The two driver channels of the SM72482 are designed as identical cells. Transistor matching inherent to integrated circuit manufacturing ensures that the AC and DC peformance of the channels are nearly identical. Closely matched propagation delays allow the dual driver to be operated as a single with inputs and output pins connected. The drive current capability in parallel operation is precisely 2X the drive of an individual channel. Small differences in switching speed between the driver channels will produce a transient current (shoot-through) in the output stage when two output pins are connected to drive a single load. Differences in input thresholds between the driver channels will also produce a transient current (shoot-through) in the output stage. Fast transition input signals are especially important while operating in a parallel configuration. The efficiency loss for parallel operation has been characterized at various loads, supply voltages and operating frequencies. The power dissipation in the SM72482 increases less than 1% relative to the dual driver configuration when operated as a single driver with inputs/ outputs connected. An Under Voltage Lock Out (UVLO) circuit is included in the SM72482, which senses the voltage difference between VCC and the chip ground pin, VEE. When the VCC to VEE voltage difference falls below 2.8V both driver channels are disabled. The UVLO hysteresis prevents chattering during brown-out conditions and the driver will resume normal operation when the VCC to VEE differential voltage exceeds approximately 3.0V. The SM72482MY -1 device hold both outputs in the low state in the under-voltage lockout (UVLO) condition. The SM72482MA-4 has an active high output state of OUT_A during UVLO. When VCC is less than the UVLO threshold voltage, OUT_A will be locked in the high state while OUT_B will be disabled in the low state. This configuration allows the SM72482MY -4 to drive a PFET through OUT_A and an NFET through OUT_B with both FETs safely turned off during UVLO. Attention must be given to board layout when using SM72482. Some important considerations include: 1. A Low ESR/ESL capacitor must be connected close to the IC and between the VCC and VEE pins to support high peak currents being drawn from VCC during turn-on of the MOSFET. 2. Proper grounding is crucial. The drivers need a very low impedance path for current return to ground avoiding inductive loops. The two paths for returning current to ground are a) between SM72482 VEE pin and the ground of the circuit that controls the driver inputs, b) between SM72482 VEE pin and the source of the power MOSFET being driven. All these paths should be as short as possible to reduce inductance and be as wide as possible to reduce resistance. All these ground paths should be kept distinctly separate to avoid coupling between the high current output paths and the logic signals that drive the SM72482. A good method is to dedicate one copper plane in a multi-layered PCB to provide a common ground surface. 3. With the rise and fall times in the range of 10 ns to 30 ns, care is required to minimize the lengths of current carrying conductors to reduce their inductance and EMI from the high di/dt transients generated by the SM72482. 4. The SM72482 footprint is compatible with other industry standard drivers including the TC4426/27/28 and UCC27323/4/5. 5. If either channel is not being used, the respective input pin (IN_A or IN_B) should be connected to either VEE or VCC to avoid spurious output signals. www.national.com Thermal Performance INTRODUCTION The primary goal of thermal management is to maintain the integrated circuit (IC) junction temperature (TJ) below a specified maximum operating temperature to ensure reliability. It is essential to estimate the maximum TJ of IC components in worst case operating conditions. The junction temperature is estimated based on the power dissipated in the IC and the junction to ambient thermal resistance JA for the IC package in the application board and environment. The JA is not a given constant for the package and depends on the printed circuit board design and the operating environment. DRIVE POWER REQUIREMENT CALCULATIONS IN SM72482 The SM72482 dual low side MOSFET driver is capable of sourcing/sinking 3A/5A peak currents for short intervals to drive a MOSFET without exceeding package power dissipation limits. High peak currents are required to switch the MOSFET gate very quickly for operation at high frequencies. 8 PD = 0.216 + 0.008 + 0.012 = 0.236W. We know that the junction temperature is given by TJ = PD x JA + TA Or the rise in temperature is given by TRISE = TJ - TA = PD x JA For SOIC-8 package JA is estimated as 170C/W for the conditions of natural convection. For MSOP8-EP JA is typically 60C/W. Therefore for SOIC TRISE is equal to 30142207 FIGURE 2. The schematic above shows a conceptual diagram of the SM72482 output and MOSFET load. Q1 and Q2 are the switches within the gate driver. RG is the gate resistance of the external MOSFET, and CIN is the equivalent gate capacitance of the MOSFET. The gate resistance Rg is usually very small and losses in it can be neglected. The equivalent gate capacitance is a difficult parameter to measure since it is the combination of CGS (gate to source capacitance) and CGD (gate to drain capacitance). Both of these MOSFET capacitances are not constants and vary with the gate and drain voltage. The better way of quantifying gate capacitance is the total gate charge QG in coloumbs. QG combines the charge required by CGS and CGD for a given gate drive voltage VGATE. Assuming negligible gate resistance, the total power dissipated in the MOSFET driver due to gate charge is approximated by TRISE = 0.236 x 170 = 40.1C CONTINUOUS CURRENT RATING OF SM72482 The SM72482 can deliver pulsed source/sink currents of 3A and 5A to capacitive loads. In applications requiring continuous load current (resistive or inductive loads), package power dissipation, limits the SM72482 current capability far below the 5A sink/3A source capability. Rated continuous current can be estimated both when sourcing current to or sinking current from the load. For example when sinking, the maximum sink current can be calculated as: where R DS(on) is the on resistance of lower MOSFET in the output stage of SM72482. Consider TJ(max) of 125C and JA of 170C/W for an SO-8 package under the condition of natural convection and no air flow. If the ambient temperature (TA) is 60C, and the RDS(on) of the SM72482 output at TJ(max) is 2.5, this equation yields ISINK(max) of 391mA which is much smaller than 5A peak pulsed currents. Similarly, the maximum continuous source current can be calculated as PDRIVER = VGATE x QG x FSW Where FSW = switching frequency of the MOSFET. For example, consider the MOSFET MTD6N15 whose gate charge specified as 30 nC for VGATE = 12V. The power dissipation in the driver due to charging and discharging of MOSFET gate capacitances at switching frequency of 300 kHz and VGATE of 12V is equal to PDRIVER = 12V x 30 nC x 300 kHz = 0.108W. If both channels of the SM72482 are operating at equal frequency with equivalent loads, the total losses will be twice as this value which is 0.216W. In addition to the above gate charge power dissipation, - transient power is dissipated in the driver during output transitions. When either output of the SM72482 changes state, current will flow from VCC to VEE for a very brief interval of time through the output totem-pole N and P channel MOSFETs. The final component of power dissipation in the driver is the power associated with the quiescent bias current consumed by the driver input stage and Under-voltage lockout sections. where VDIODE is the voltage drop across hybrid output stage which varies over temperature and can be assumed to be about 1.1V at TJ(max) of 125C. Assuming the same parameters as above, this equation yields ISOURCE(max) of 347mA. 9 www.national.com SM72482 Characterization of the SM72482 provides accurate estimates of the transient and quiescent power dissipation components. At 300 kHz switching frequency and 30 nC load used in the example, the transient power will be 8 mW. The 1 mA nominal quiescent current and 12V VGATE supply produce a 12 mW typical quiescent power. Therefore the total power dissipation SM72482 Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. STANDARD LEAD FINISH TO BE 200 MICROINCHES/5.08 MICROMETERS MINIMUM LEAD/TIN(SOLDER) ON COPPER. 2. 3. DIMENSION DOES NOT INCLUDE MOLD FLASH. REFERENCE JEDEC REGISTRATION MS-012, VARIATION AA, DATED MAY 1990. 8-Lead SOIC Package NS Package Number M08A 8-Lead Exposed Pad MSOP Package NS Package Number MUY08A www.national.com 10 SM72482 11 www.national.com SM72482 SolarMagic Dual 5A Compound Gate Driver Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated