AT86RF233
Low Power, 2.4GHz Transceiver for ZigBee, RF4CE, IEEE
802.15.4, 6LoWPAN, and ISM Applications
PRELIMINARY DATASHEET
Features
• High Performance RF-CMOS 2.4GHz radio transceiver targeted for IEEE® 802.15.4,
ZigBee®, RF4CE, 6LoWPAN, and ISM applications
• Industry leading link budget:
• Receiver sensitivity -101dBm
• Programmable TX output power from -17dBm up to +4dBm
• Ultra-low current consumption:
• DEEP_SLEEP = 0.02µA
• TRX_OFF = 300µA
• RX_ON = 11.8mA (LISTEN)
• Smart Receiving Techniques enable further current reduction in LISTEN mode
between 10 to 50% from 11.8mA
• Desensitation will enable further reduction up to 1mA
• BUSY_TX = 13.8mA (at max. transmit power)
• Ultra-low supply voltage (1.8V to 3.6V) with internal regulator
• Support for coin cell operation
• Optimized for low BoM Cost and ease of production:
• Few external components necessary (crystal, capacitors and antenna)
• Easy to use interface:
• Registers, frame buffer, and AES accessible through fast SPI
• Only two microcontroller GPIO lines necessary
• One interrupt pin from radio transceiver
• Clock output with prescaler from radio transceiver
• Radio transceiver features:
• 128-byte FIFO (SRAM) for data buffering
• Fully integrated, fast settling PLL to support Frequency Hopping
• Supports 500kHz channel spacing
• Battery monitor and Fast Wake-Up Time < 0.4msec
• Special IEEE 802.15.4™ 2011 hardware support:
• FCS computation and Clear Channel Assessment
• RSSI measurement, Energy Detection and Link Quality Indication
• MAC hardware accelerator:
• Automated acknowledgement, CSMA-CA and retransmission
• Automatic address filtering
• Automated FCS check
• Extended feature set hardware support:
• AES 128-bit hardware accelerator
• Antenna Diversity and RX/TX indication
• Supported PSDU data rates: 250kb/s, 500kb/s, 1000kb/s and 2000kb/s
• True Random Number Generation for security application
• Reduced Power Consumption modes
• Time and phase measurement support
• Industrial and extended temperature range:
• -40°C to +85°C and -40°C to +125°C
• I/O and packages:
• 32-pin Low-Profile QFN Package 5 x 5 x 0.9mm³
• RoHS/Fully Green
• Compliant to EN 300 328/440, FCC-CFR-47 Part 15, ARIB STD-66, RSS-210
• Compliant to IEEE 802.15.4 2003/2006/2011
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
2
Table of Contents
1 Pin-out Diagram ............................................................................................................................ 7
1.1 Pin Descriptions ......................................................................................................................................................... 8
1.2 Analog and RF Pins ................................................................................................................................................... 9
1.2.1 Supply and Ground Pins ........................................................................................................................................................ 9
1.2.2 RF Pins .................................................................................................................................................................................. 9
1.2.3 Crystal Oscillator Pins .......................................................................................................................................................... 10
1.2.4 Analog Pin Summary ........................................................................................................................................................... 10
1.3 Digital Pins ............................................................................................................................................................... 11
1.3.1 Driver Strength Settings ....................................................................................................................................................... 11
1.3.2 Pull-up and Pull-down Configuration .................................................................................................................................... 11
2 Disclaimer .................................................................................................................................... 12
3 Overview ...................................................................................................................................... 12
4 General Circuit Description ........................................................................................................ 13
5 Application Schematic ................................................................................................................ 15
5.1 Basic Application Schematic .................................................................................................................................... 15
5.2 Extended Feature Set Application Schematic ......................................................................................................... 17
6 Microcontroller Interface ............................................................................................................ 19
6.1 Overview .................................................................................................................................................................. 19
6.2 SPI Timing Description ............................................................................................................................................ 20
6.3 SPI Protocol ............................................................................................................................................................. 21
6.3.1 Register Access Mode ......................................................................................................................................................... 21
6.3.2 Frame Buffer Access Mode ................................................................................................................................................. 22
6.3.3 SRAM Access Mode ............................................................................................................................................................ 24
6.4 Radio Transceiver Status information ..................................................................................................................... 25
6.4.1 Register Description ............................................................................................................................................................ 25
6.5 Radio Transceiver Identification .............................................................................................................................. 27
6.5.1 Register Description ............................................................................................................................................................ 27
6.6 Sleep/Wake-up and Transmit Signal (SLP_TR) ...................................................................................................... 29
6.7 Interrupt Logic .......................................................................................................................................................... 31
6.7.1 Overview .............................................................................................................................................................................. 31
6.7.2 Interrupt Mask Modes and Pin Polarity ................................................................................................................................ 32
6.7.3 Register Description ............................................................................................................................................................ 33
7 Operating Modes ......................................................................................................................... 36
7.1 Basic Operating Mode ............................................................................................................................................. 36
7.1.1 State Control ........................................................................................................................................................................ 37
7.1.2 Basic Operating Mode Description ...................................................................................................................................... 37
7.1.3 Interrupt Handling ................................................................................................................................................................ 41
7.1.4 Basic Operating Mode Timing ............................................................................................................................................. 42
7.1.5 Register Description ............................................................................................................................................................ 48
7.2 Extended Operating Mode ....................................................................................................................................... 50
7.2.1 State Control ........................................................................................................................................................................ 52
7.2.2 Configuration ....................................................................................................................................................................... 53
7.2.3 RX_AACK_ON – Receive with Automatic ACK ................................................................................................................... 54
7.2.4 TX_ARET_ON – Transmit with Automatic Frame Retransmission and CSMA-CA Retry .................................................... 63
7.2.5 Interrupt Handling ................................................................................................................................................................ 67
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
3
7.2.6 Register Summary ............................................................................................................................................................... 68
7.2.7 Register Description ............................................................................................................................................................ 68
8 Functional Description ............................................................................................................... 80
8.1 Introduction – IEEE 802.15.4-2006 Frame Format.................................................................................................. 80
8.1.1 PHY Protocol Data Unit (PPDU) .......................................................................................................................................... 80
8.1.2 MAC Protocol Data Unit (MPDU) ......................................................................................................................................... 82
8.2 Frame Filter .............................................................................................................................................................. 86
8.2.1 Configuration ....................................................................................................................................................................... 87
8.2.2 Handling of Reserved Frame Types .................................................................................................................................... 87
8.2.3 Register Description ............................................................................................................................................................ 88
8.2.4 Register Description – Address Registers ........................................................................................................................... 91
8.3 Frame Check Sequence (FCS) ............................................................................................................................... 96
8.3.1 Overview .............................................................................................................................................................................. 96
8.3.2 CRC Calculation .................................................................................................................................................................. 96
8.3.3 Automatic FCS Generation .................................................................................................................................................. 97
8.3.4 Automatic FCS Check ......................................................................................................................................................... 97
8.3.5 Register Description ............................................................................................................................................................ 97
8.4 Received Signal Strength Indicator (RSSI) ............................................................................................................. 99
8.4.1 Overview .............................................................................................................................................................................. 99
8.4.2 Reading RSSI ...................................................................................................................................................................... 99
8.4.3 Data Interpretation ............................................................................................................................................................... 99
8.4.4 Register Description .......................................................................................................................................................... 100
8.5 Energy Detection (ED) ........................................................................................................................................... 101
8.5.1 Overview ............................................................................................................................................................................ 101
8.5.2 Measurement Description .................................................................................................................................................. 101
8.5.3 Data Interpretation ............................................................................................................................................................. 102
8.5.4 Interrupt Handling .............................................................................................................................................................. 102
8.5.5 Register Description .......................................................................................................................................................... 103
8.6 Clear Channel Assessment (CCA) ........................................................................................................................ 104
8.6.1 Overview ............................................................................................................................................................................ 104
8.6.2 Configuration and Request ................................................................................................................................................ 104
8.6.3 Data Interpretation ............................................................................................................................................................. 105
8.6.4 Interrupt Handling .............................................................................................................................................................. 105
8.6.5 Measurement Time ............................................................................................................................................................ 105
8.6.6 Register Description .......................................................................................................................................................... 106
8.7 Link Quality Indication (LQI) .................................................................................................................................. 109
8.7.1 Overview ............................................................................................................................................................................ 109
8.7.2 Obtaining the LQI Value .................................................................................................................................................... 110
8.7.3 Data Interpretation ............................................................................................................................................................. 110
9 Module Description ................................................................................................................... 111
9.1 Receiver (RX) ........................................................................................................................................................ 111
9.1.1 Overview ............................................................................................................................................................................ 111
9.1.2 Frame Receive Procedure ................................................................................................................................................. 111
9.1.3 Configuration ..................................................................................................................................................................... 111
9.1.4 Register Description .......................................................................................................................................................... 112
9.2 Transmitter (TX) ..................................................................................................................................................... 115
9.2.1 Overview ............................................................................................................................................................................ 115
9.2.2 Frame Transmit Procedure ................................................................................................................................................ 115
9.2.3 Configuration ..................................................................................................................................................................... 115
9.2.4 TX Power Ramping ............................................................................................................................................................ 116
9.2.5 Register Description .......................................................................................................................................................... 116
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
4
9.3 Frame Buffer .......................................................................................................................................................... 118
9.3.1 Data Management ............................................................................................................................................................. 118
9.3.2 User accessible Frame Content......................................................................................................................................... 119
9.3.3 Interrupt Handling .............................................................................................................................................................. 119
9.4 Voltage Regulators (AVREG, DVREG) ................................................................................................................. 121
9.4.1 Overview ............................................................................................................................................................................ 121
9.4.2 Configuration ..................................................................................................................................................................... 122
9.4.3 Data Interpretation ............................................................................................................................................................. 122
9.4.4 Register Description .......................................................................................................................................................... 122
9.5 Battery Monitor (BATMON) .................................................................................................................................... 124
9.5.1 Overview ............................................................................................................................................................................ 124
9.5.2 Configuration ..................................................................................................................................................................... 124
9.5.3 Data Interpretation ............................................................................................................................................................. 124
9.5.4 Interrupt Handling .............................................................................................................................................................. 125
9.5.5 Register Description .......................................................................................................................................................... 125
9.6 Crystal Oscillator (XOSC) ...................................................................................................................................... 127
9.6.1 Overview ............................................................................................................................................................................ 127
9.6.2 Integrated Oscillator Setup ................................................................................................................................................ 127
9.6.3 External Reference Frequency Setup ................................................................................................................................ 128
9.6.4 Master Clock Signal Output (CLKM) .................................................................................................................................. 128
9.6.5 Register Description .......................................................................................................................................................... 129
9.7 Frequency Synthesizer (PLL) ................................................................................................................................ 132
9.7.1 Overview ............................................................................................................................................................................ 132
9.7.2 RF Channel Selection ........................................................................................................................................................ 132
9.7.3 PLL Settling Time and Frequency Agility ........................................................................................................................... 133
9.7.4 Calibration Loops ............................................................................................................................................................... 133
9.7.5 Interrupt Handling .............................................................................................................................................................. 134
9.7.6 Register Description .......................................................................................................................................................... 134
9.8 Automatic Filter Tuning (FTN) ............................................................................................................................... 139
9.8.1 Overview ............................................................................................................................................................................ 139
9.8.2 Register Description .......................................................................................................................................................... 139
10 Radio Transceiver Usage ....................................................................................................... 141
10.1 Frame Receive Procedure ................................................................................................................................... 141
10.2 Frame Transmit Procedure .................................................................................................................................. 142
11 AT86RF233 Extended Feature Set ......................................................................................... 143
11.1 Security Module (AES) ........................................................................................................................................ 143
11.1.1 Overview .......................................................................................................................................................................... 143
11.1.2 Security Module Preparation ........................................................................................................................................... 143
11.1.3 Security Key Setup .......................................................................................................................................................... 144
11.1.4 Security Operation Modes ............................................................................................................................................... 144
11.1.5 Data Transfer – Fast SRAM Access ................................................................................................................................ 147
11.1.6 Start of Security Operation and Status ............................................................................................................................ 147
11.1.7 SRAM Register Summary ................................................................................................................................................ 148
11.1.8 Register Description ........................................................................................................................................................ 148
11.2 Random Number Generator ................................................................................................................................ 151
11.2.1 Overview .......................................................................................................................................................................... 151
11.2.2 Register Description ........................................................................................................................................................ 151
11.3 High Data Rate Modes ........................................................................................................................................ 152
11.3.1 Overview .......................................................................................................................................................................... 152
11.3.2 High Data Rate Packet Structure ..................................................................................................................................... 153
11.3.3 High Data Rate Frame Buffer Access .............................................................................................................................. 154
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
5
11.3.4 High Data Rate Energy Detection .................................................................................................................................... 154
11.3.5 High Data Rate Mode Options ......................................................................................................................................... 154
11.3.6 Register Description ........................................................................................................................................................ 156
11.4 Antenna Diversity ................................................................................................................................................. 159
11.4.1 Overview .......................................................................................................................................................................... 159
11.4.2 Antenna Diversity Application Example ........................................................................................................................... 159
11.4.3 Antenna Diversity Sensitivity Control ............................................................................................................................... 160
11.4.4 Register Description ........................................................................................................................................................ 161
11.5 RX/TX Indicator ................................................................................................................................................... 164
11.5.1 Overview .......................................................................................................................................................................... 164
11.5.2 External RF-Front End Control ........................................................................................................................................ 164
11.5.3 Register Description ........................................................................................................................................................ 165
11.6 RX and TX Frame Time Stamping (TX_ARET) ................................................................................................... 166
11.6.1 Overview .......................................................................................................................................................................... 166
11.6.2 Register Description ........................................................................................................................................................ 166
11.7 Frame Buffer Empty Indicator .............................................................................................................................. 168
11.7.1 Overview .......................................................................................................................................................................... 168
11.7.2 Register Description ........................................................................................................................................................ 169
11.8 Dynamic Frame Buffer Protection........................................................................................................................ 170
11.8.1 Overview .......................................................................................................................................................................... 170
11.8.2 Register Description ........................................................................................................................................................ 170
11.9 Alternate Start-Of-Frame Delimiter ...................................................................................................................... 171
11.9.1 Overview .......................................................................................................................................................................... 171
11.9.2 Register Description ........................................................................................................................................................ 171
11.10 Reduced Power Consumption Mode (RPC) ...................................................................................................... 172
11.10.1 Overview ........................................................................................................................................................................ 172
11.10.2 RPC Methods and Elements.......................................................................................................................................... 172
11.10.3 Register Summary ......................................................................................................................................................... 175
11.11 Time-Of-Flight Module (TOM) ............................................................................................................................ 177
11.11.1 Overview ........................................................................................................................................................................ 177
11.11.2 Interrupt Handling .......................................................................................................................................................... 177
11.11.3 TOM Measurements ...................................................................................................................................................... 177
11.11.4 Register Summary ......................................................................................................................................................... 179
11.11.5 Frame Buffer Content Summary .................................................................................................................................... 180
11.12 Phase Difference Measurement ........................................................................................................................ 187
11.12.1 Overview ........................................................................................................................................................................ 187
11.12.2 Register Summary ......................................................................................................................................................... 187
12 Electrical Characteristics ....................................................................................................... 189
12.1 Absolute Maximum Ratings ................................................................................................................................. 189
12.2 Recommended Operating Range ........................................................................................................................ 189
12.3 Digital Pin Characteristics .................................................................................................................................... 190
12.4 Digital Interface Timing Characteristics ............................................................................................................... 190
12.5 General RF Specifications ................................................................................................................................... 191
12.6 Transmitter Characteristics .................................................................................................................................. 192
12.7 Receiver Characteristics ...................................................................................................................................... 192
12.8 Current Consumption Specifications ................................................................................................................... 193
12.9 Crystal Parameter Requirements ........................................................................................................................ 194
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
6
13 Typical Characteristics ........................................................................................................... 195
13.1 Active Supply Current .......................................................................................................................................... 195
13.1.1 P_ON and TRX_OFF states ............................................................................................................................................ 195
13.1.2 PLL_ON state .................................................................................................................................................................. 196
13.1.3 RX_ON state.................................................................................................................................................................... 197
13.1.4 TX_BUSY state................................................................................................................................................................ 198
13.1.5 SLEEP ............................................................................................................................................................................. 200
13.1.6 DEEP_SLEEP ................................................................................................................................................................. 200
13.2 State Transition Timing ........................................................................................................................................ 201
14 Register Reference ................................................................................................................. 203
15 Abbreviations .......................................................................................................................... 206
16 Ordering Information .............................................................................................................. 208
17 Soldering Information ............................................................................................................. 208
18 Package Thermal Properties .................................................................................................. 208
19 Package Drawing – 32QN2 ..................................................................................................... 209
Appendix A Continuous Transmission Test Mode ................................................................ 210
A.1 Overview ........................................................................................................................................................... 210
A.2 Configuration ..................................................................................................................................................... 210
A.3 Register Description .......................................................................................................................................... 212
Appendix B AT86RF233-ZF / AT86RF233-ZFR Extended Temperature Range .................... 213
B.1 Introduction ....................................................................................................................................................... 213
B.2 Reduced Feature Set ........................................................................................................................................ 213
B.3 Electrical Characteristics ................................................................................................................................... 213
B.3.1 Recommended Operating Range ............................................................................................................................... 213
B.3.2 General RF Specifications .......................................................................................................................................... 214
B.4 Typical Characteristics ...................................................................................................................................... 214
B.4.1 Active Supply Current ................................................................................................................................................. 214
B.4.2 State Transition Timing ............................................................................................................................................... 218
B.4.3 Receiver Performance ................................................................................................................................................ 219
B.4.4 Transmitter Performance ............................................................................................................................................ 220
Appendix C Errata ..................................................................................................................... 222
AT86RF233 Rev. A ...................................................................................................................................................... 222
References .................................................................................................................................... 223
Data Sheet Revision History ....................................................................................................... 224
Rev. 8315E–MCU Wireless–07/14 .............................................................................................................................. 224
Rev. 8351D–MCU Wireless–08/13 .............................................................................................................................. 224
Rev. 8351C–MCU Wireless–02/13 .............................................................................................................................. 224
Rev. 8351B–MCU Wireless–06/12 .............................................................................................................................. 224
Rev. 8351A–MCU Wireless–02/12 .............................................................................................................................. 224
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
7
1 Pin-out Diagram
Figure 1-1. Atmel AT86RF233 Pin-out Diagram.
32
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
AT86RF233
CLKM
DVSS
DIG3
DIG4
AVSS
AVSS
RFP
RFN
DVSS
/RST
DIG1
DIG2
SLP_TR
DVSS
DVDD
DVDD
DEVDD
DVSS
SCLK
MISO
DVSS
MOSI
/SEL
IRQ
XTAL2
XTAL1
AVSS
EVDD
AVDD
AVSS
AVSS
AVSS
31 30 29 28 27 26 25
9 10 11 12 13 14 15 16
AVSS
exposed paddle
Note: 1.
The exposed paddle is electrically connected to the die inside the package. It
shall be soldered to the board to ensure electrical and thermal contact and good
mechanical stability.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
8
1.1 Pin Descriptions
Table 1-1. Atmel AT86RF233 Pin Description.
Pins Name Type Description
1 DIG3 Digital output (Ground) 1. RX/TX Indicator, see Section 11.5
2. If disabled, pull-down enabled (AVSS)
2 DIG4 Digital output (Ground) 1. RX/TX Indicator (DIG3 inverted), see Section 11.5
2. If disabled, pull-down enabled (AVSS)
3 AVSS Ground Ground for RF signals
4 RFP RF I/O Differential RF signal
5 RFN RF I/O Differential RF signal
6 AVSS Ground Ground for RF signals
7 DVSS Ground Digital ground
8 /RST Digital input Chip reset; active low
9 DIG1 Digital output (Ground) 1. Antenna Diversity RF switch control, see Section 11.4
2. If disabled, pull-down enabled (DVSS)
10 DIG2 Digital output (Ground) 1. Antenna Diversity RF switch control (DIG1 inverted), see Section 11.4
2. RX Frame Time Stamping, see Section 11.6
3. TX Frame Time Stamping, see Section 11.6
4. If functions disabled, pull-down enabled (DVSS)
11 SLP_TR Digital input Controls sleep, deep sleep, transmit start, receive states; active high, see
Section 6.6
12 DVSS Ground Digital ground
13, 14 DVDD Supply Regulated 1.8V voltage regulator output or regulated voltage input; digital
domain, see Section 9.4
15 DEVDD Supply External supply voltage; digital domain
16 DVSS Ground Digital ground
17 CLKM Digital output Master clock signal output; low if disabled, see Section 9.6
18 DVSS Ground Digital ground
19 SCLK Digital input SPI clock
20 MISO Digital output SPI data output (master input slave output)
21 DVSS Ground Digital ground
22 MOSI Digital input SPI data input (master output slave input)
23 /SEL Digital input SPI select, active low
24 IRQ Digital output 1. Interrupt request signal; active high or active low; configurable, see
Section 6.7
2. Frame Buffer Empty Indicator; active high, see Section 11.7
25 XTAL2 Analog input Crystal pin, see Section 9.6
26 XTAL1 Analog input Crystal pin or external clock supply, see Section 9.6
27 AVSS Ground Analog ground
28 EVDD Supply External supply voltage, analog domain
29 AVDD Supply Regulated 1.8V voltage regulator; analog domain, see Section 9.4
30, 31, 32 AVSS Ground Analog ground
Paddle AVSS Ground Analog ground; Exposed paddle of QFN package
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
9
1.2 Analog and RF Pins
1.2.1 Supply and Ground Pins
EVDD, DEVDD
EVDD and DEVDD are analog and digital supply voltage pins of the Atmel® AT86RF233
radio transceiver.
AVDD, DVDD
AVDD and DVDD are outputs of the internal voltage regulators and require bypass
capacitors for stable operation. The voltage regulators are controlled independently by
the radio transceivers state machine and are activated depending on the current radio
transceiver state. The voltage regulators can be configured for external supply; for
details, refer to Section 9.4.
AVSS, DVSS
AVSS and DVSS are analog and digital ground pins respectively. The analog and
digital power domains should be separated on the PCB.
1.2.2 RF Pins
RFN, RFP
A differential RF port (RFP/RFN) provides common-mode rejection to suppress the
switching noise of the internal digital signal processing blocks. At board-level, the
differential RF layout ensures high receiver sensitivity by reducing spurious emissions
originated from other digital ICs such as a microcontroller.
The RF port is designed for a 100Ω differential load. A DC path between the RF pins is
allowed; a DC path to ground or supply voltage is not allowed.
A simplified schematic of the RF front end is shown in Figure 1-2.
Figure 1-2. Simplified RF Front-end Schematic.
LNA
PA
RXTX
0.9V
TX
RX
CM
Feedback
M0
AT86RF233PCB
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
10
The RF port DC values depend on the operating state; refer to Chapter 7. In TRX_OFF
state, when the analog front-end is disabled (see Section 7.1.2.5), the RF pins are
pulled to ground, preventing a floating voltage larger than 1.8V which is not allowed for
the internal circuitry.
In transmit mode, a control loop provides a common-mode voltage of 0.9V. Transistor
M0 is off, allowing the PA to set the common-mode voltage. The common-mode
capacitance at each pin to ground shall be < 30pF to ensure the stability of this
common-mode feedback loop.
In receive mode, the RF port provides a low-impedance path to ground when transistor
M0, (see Figure 1-2) pulls the inductor center tap to ground. A DC voltage drop of 20mV
across the on-chip inductor can be measured at the RF pins.
1.2.3 Crystal Oscillator Pins
XTAL1, XTAL2
The pin 26 (XTAL1) of Atmel AT86RF233 is the input of the reference oscillator
amplifier (XOSC), the pin 25 (XTAL2) is the output. A detailed description of the crystal
oscillator setup and the related XTAL1/XTAL2 pin configuration can be found in
Section 9.6.
When using an external clock reference signal, XTAL1 shall be used as input pin. For
further details, refer to Section 9.6.3.
1.2.4 Analog Pin Summary
Table 1-2. Analog Pin Behavior – DC values.
Pin Values and Conditions Comments
RFP/RFN VDC = 0.9V (BUSY_TX)
VDC = 20mV (receive states)
VDC = 0mV (otherwise)
DC level at pins RFP/RFN for various transceiver states.
AC coupling is required if a circuitry with a DC path to ground or
supply is used. Serial capacitance and capacitance of each pin
to ground must be < 30pF.
XTAL1/XTAL2 VDC = 0.9V at both pins
CPAR = 3pF
DC level at pins XTAL1/XTAL2 for various transceiver states.
Parasitic capacitance (CPAR) of the pins must be considered as
additional load capacitance to the crystal.
DVDD VDC = 1.8V (all states, except SLEEP
and DEEP_SLEEP)
VDC = 0mV (otherwise)
DC level at pin DVDD for various transceiver states.
Supply pins (voltage regulator output) for the digital 1.8V
voltage domain. The outputs shall be bypassed by 100nF.
AVDD VDC = 1.8V (all states, except P_ON,
SLEEP, DEEP_SLEEP, RESET, and
TRX_OFF)
VDC = 0mV (otherwise)
DC level at pin AVDD for various transceiver states.
Supply pin (voltage regulator output) for the analog 1.8V
voltage domain. The outputs shall be bypassed by 100nF.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
11
1.3 Digital Pins
The Atmel AT86RF233 provides a digital microcontroller interface. The interface
comprises a slave SPI (/SEL, SCLK, MOSI, and MISO) and additional control signals
(CLKM, IRQ, SLP_TR, /RST, and DIG2). The microcontroller interface is described in
detail in Chapter 6.
Additional digital output signals DIG1, …, DIG4 are provided to control external blocks,
that is for Antenna Diversity RF switch control or as an RX/TX Indicator, see
Section 11.4 and Section 11.5 respectively.
1.3.1 Driver Strength Settings
The driver strength of all digital output pins (MISO, IRQ, DIG1, …, DIG4) and CLKM pin
are fixed. The capacitive load should be as small as possible as, not larger than 50pF.
1.3.2 Pull-up and Pull-down Configuration
Pulling transistors are internally connected to all digital input pins in radio transceiver
states P_ON (including reset during P_ON) and DEEP_SLEEP, refer to Section 7.1.2.1
and Section 7.1.2.4.
Table 1-3 summarizes the pull-up and pull-down configuration.
Table 1-3. Pull-Up / Pull-Down Configuration of Digital Input Pins.
Pin H
=
ˆ
pull-up, L
=
ˆ
pull-down
/RST H
/SEL H
SCLK L
MOSI L
SLP_TR(1) L
Note: 1. Except SLP_TR pin for DEEP_SLEEP state.
In all other radio transceiver states, including RESET, no pull-up or pull-down
transistors are connected to any of the digital input pins mentioned in Table 1-3.
Note: 2. In all other states, external circuitry should guaranty defined levels at all input
pins. Floating input pins may cause unexpected functionality and increased
power consumption, for example in SLEEP state.
If the additional digital output signals DIG1, …, DIG4 are not activated, these pins are
pulled-down to digital ground (DIG1/DIG2) or analog ground (DIG3/DIG4).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
12
2 Disclaimer
Typical values contained in this datasheet are based on simulations and testing.
Minimum and maximum values are available when the radio transceiver has been fully
characterized.
3 Overview
The Atmel AT86RF233 is a feature rich, extremely low-power 2.4GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, RF4CE, 6LoWPAN, and
high data rate 2.4GHz ISM band applications.
The AT86RF233 is a true SPI-to-antenna solution. All RF-critical components except
the antenna, crystal, and de-coupling capacitors are integrated on-chip. MAC and AES
hardware accelerators improve overall system power efficiency and timing. Therefore,
the AT86RF233 is particularly suitable for applications like:
• 2.4GHz IEEE 802.15.4 and ZigBee systems
• RF4CE systems
• Energy Harvesting systems
• 6LoWPAN systems
• Wireless sensor networks
• Industrial Control
• Residential and commercial automation
• Health care
• Consumer electronics
• PC peripherals
The AT86RF233 can be operated by using an external microcontroller like Atmel AVR®
microcontrollers. A comprehensive software programming description can be found in
reference [7].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
13
4 General Circuit Description
The Atmel AT86RF233 single-chip radio transceiver provides a complete radio
transceiver interface between an antenna and a microcontroller. It comprises the analog
radio, digital modulation and demodulation including time and frequency
synchronization, as well as data buffering. A single 128-byte TRX buffer stores receive
or transmit data. Communication between transmitter and receiver is based on direct
sequence spread spectrum with different modulation schemes and spreading codes.
The AT86RF233 block diagram is shown in Figure 4-1.
Figure 4-1. AT86RF233 Block Diagram.
The number of external components is minimized such that only the antenna, the
crystal and decoupling capacitors are required. The bidirectional differential antenna
pins (RFP, RFN) are used for transmission and reception, thus no external antenna
switch is needed. Control of an external power amplifier is supported by two digital
control signals (differential operation).
The received RF signal at pin 5 (RFN) and pin 6 (RFP) is differentially fed through the
low-noise amplifier (LNA) to the RF filter (PPF) to generate a complex signal, driving the
integrated channel filter (BPF). The limiting amplifier provides sufficient gain to drive the
succeeding analog-to-digital converter (ADC) and generates a digital RSSI signal. The
ADC output signal is sampled by the digital base band receiver (RX BBP).
The transmit modulation scheme is offset-QPSK (O-QPSK) with half-sine pulse shaping
and 32-length block coding (spreading) according to [1], [2] and [3]. The modulation
signal is generated in the digital transmitter (TX BBP) and applied to the fractional-N
frequency synthesis (PLL), to ensure the coherent phase modulation required for
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
14
demodulation of O-QPSK signals. The frequency-modulated signal is fed to the power
amplifier (PA).
Two on-chip low-dropout voltage regulators (A|DVREG) provide regulated analog and
digital 1.8V supply outputs.
An internal 128-byte RAM for RX and TX (Frame Buffer) buffers the data to be
transmitted or the received data.
The configuration of the Atmel AT86RF233, reading and writing of Frame Buffer is
controlled by the SPI interface and additional control lines.
The AT86RF233 further contains comprehensive hardware-MAC support (Extended
Operating Mode) and a security engine (AES) to improve the overall system power
efficiency and timing. The stand-alone 128-bit AES engine can be accessed in parallel
to all PHY operational transactions and states using the SPI interface, except during
SLEEP and DEEP_SLEEP states.
For applications not necessarily targeting IEEE 802.15.4 compliant networks, the radio
transceiver also supports alternative data rates up to 2000kb/s.
For long-range applications or to improve the reliability of a RF connection the RF
performance can further be improved by using an external RF front-end or Antenna
Diversity. Both operation modes are supported by the AT86RF233 with dedicated
control pins DIG1, …, DIG4 without the interaction of the microcontroller.
Additional features of the Extended Feature Set, see Chapter 11, are provided to
simplify the interaction between radio transceiver and microcontroller.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
15
5 Application Schematic
5.1 Basic Application Schematic
A basic application schematic of the Atmel AT86RF233 with a single-ended RF
connector is shown in Figure 5-1. The 50Ω single-ended RF input is transformed to the
100Ω differential RF port impedance using balun B1. The capacitors C1 and C2 provide
AC coupling of the RF input to the RF port, optional capacitor C4 improves matching if
required.
Figure 5-1. Basic Application Schematic.
8
7
6
5
4
3
2
1
910 11 12 13 14 15 16
2526
2728
2930
3132
AT86RF233
DIG3
AVSS
DIG4
AVSS
AVSS
RFP
RFN
AVSS
DVSS
DIG1
DIG2
SLP_TR
DVSS
DVDD
DVDD
XTAL2
DEVDD
DVSS
AVSS
AVDD
EVDD
AVSS
XTAL1
17
18
19
20
21
22
23
24
DVSS
CLKM
IRQ
MISO
DVSS
MOSI
SCLK
CB3 CB4
Digital Interface
/RST
/SEL
V
DD
XTAL
CX1 CX2
CB1
V
DD
CB2
C1
C2
B1
RF
C3
R1
C4
The power supply decoupling capacitors (CB2, CB4) are connected to the external
analog supply pin 28 (EVDD) and external digital supply pin 15 (DEVDD). Capacitors
CB1 and CB3 are bypass capacitors for the integrated analog and digital voltage
regulators to ensure stable operation. All bypass capacitors should be placed as close
as possible to the pins and should have a low-resistance and low-inductance
connection to ground to achieve the best performance.
The crystal (XTAL), the two load capacitors (CX1, CX2), and the internal circuitry
connected to pins XTAL1 and XTAL2 form the crystal oscillator. To achieve the best
accuracy and stability of the reference frequency, large parasitic capacitances should
be avoided. Crystal lines should be routed as short as possible and not in proximity of
digital I/O signals. This is especially required for the High Data Rate Modes; refer to
Section 11.3.
Crosstalk from digital signals on the crystal pins or the RF pins can degrade the system
performance. Therefore, a low-pass filter (C3, R1) is placed close to the
Atmel AT86RF233 CLKM output pin to reduce the emission of CLKM signal harmonics.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
16
This is not needed if pin 17 (CLKM) is not used as a microcontroller clock source. In this
case, pin 17 (CLKM) output should be disabled during device initialization.
The ground plane of the application board should be separated into four independent
fragments: the analog, the digital, the antenna, and the XTAL ground plane. The
exposed paddle shall act as the reference point of the individual grounds.
Note: 1. The pins DIG1, DIG2, DIG3, and DIG4 are connected to ground in the Basic
Application Schematic; refer to Figure 5-1. Special programming of these pins
requires a different schematic; refer to Section 5.2.
Table 5-1. Exemplary Bill of Materials (BoM) for Basic Application Schematic.
Symbol Description Value Manufacturer Part Number Comment
B1 SMD balun 2.45GHz Wuerth 748421245 2.45GHz Balun
B1
(alternatively)
SMD balun / filter 2.45GHz Johanson
Technology
2450BM15A0015
2.45GHz Balun / Filter
CB1
CB3
LDO VREG
bypass capacitor
100nF Generic X7R
(0402)
10% 16V
CB2
CB4
Power supply decoupling 1µF AVX
Murata
0603YD105KAT2A
GRM188R61C105KA12D
X5R
(0603)
10% 16V
CX1, CX2
Crystal load capacitor
12pF
AVX
Murata
06035A120JA
GRM1555C1H120JA01D
COG
(0402)
5% 50V
C1, C2
RF coupling capacitor
22pF
Murata
Epcos
AVX
GRM1555C1H220JA01J
B37920
06035A220JAT2A
C0G 5% 50V
(0402 or 0603)
C3 CLKM low-pass
filter capacitor
2.2pF AVX
Murata
06035A229DA
GRP1886C1H2R0DA01
COG
(0603)
±0.5pF 50V
Designed for fCLKM = 1MHz
C4 (optional) RF matching Value depends on final
PCB implementation
R1 CLKM low-pass
filter resistor
680Ω Designed for fCLKM = 1MHz
XTAL Crystal CX-4025 16MHz
SX-4025 16MHz
ACAL Taitjen
Siward
XWBBPL-F-1
A207-011
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
17
5.2 Extended Feature Set Application Schematic
The Atmel AT86RF233 supports additional features like:
• Security Module (AES) Section 11.1
• Random Number Generator Section 11.2
• High Data Rate Modes Section 11.3
• Antenna Diversity uses pins DIG1(/2) Section 11.4
• RX/TX Indicator uses pins DIG3/4 Section 11.5
• RX and TX Frame Time Stamping (TX_ARET)
uses pin DIG2 Section 11.6
• Frame Buffer Empty Indicator uses pin IRQ Section 11.7
• Dynamic Frame Buffer Protection Section 11.8
• Alternate Start-Of-Frame Delimiter Section 11.9
• Reduced Power Consumption Mode (RPC) Section 11.10
• TOM Measurements Section 11.11
• Phase Difference Measurement Section 11.12
An extended feature set application schematic illustrating the use of the AT86RF233
Extended Feature Set, see Chapter 11, is shown in Figure 5-2. Although this example
shows all additional hardware features combined, it is possible to use all features
separately or in various combinations.
Figure 5-2. Extended Feature Application Schematic.
8
7
6
5
4
3
2
1
910 11 12 13 14 15 16
2526
2728
2930
3132
AT86RF233
DIG3
AVSS
DIG4
AVSS
AVSS
RFP
RFN
AVSS
DVSS
DIG1
DIG2
SLP_TR
DVSS
DVDD
DVDD
XTAL2
DEVDD
DVSS
AVSS
AVDD
EVDD
AVSS
XTAL1
17
18
19
20
21
22
23
24
DVSS
CLKM
IRQ
MISO
DVSS
MOSI
SCLK
CB3 CB4
XTAL
CX1 CX2
CB1
Digital Interface
V
DD
/RST
/SEL
Balun
ANT0
RF-
Switch
B1SW1
SW2
V
DD
CB2
C3
R1
PA
LNA
N1
N2
ANT1
RF-
Switch
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
18
In this example, a balun (B1) transforms the differential RF signal at the
Atmel AT86RF233 radio transceiver RF pins (RFP/RFN) to a single ended RF signal,
similar to the Basic Application Schematic; refer to Figure 5-1. During receive mode the
radio transceiver searches for the most reliable RF signal path using the Antenna
Diversity algorithm. One antenna is selected (SW2) by the Antenna Diversity RF switch
control pin 9 (DIG1), refer to Section 11.4.
The RX signal is amplified by an optional low-noise amplifier (N2) and fed to the radio
transceiver using the RX/TX switch (SW1). During transmit mode the AT86RF233 TX
signal is amplified using an external PA (N1) and fed to the antennas via an RF switch
(SW2). These switches are controlled by the RX/TX Indicator, represented by the
differential pin pair DIG3/DIG4, refer to Section 11.5.
RX and TX Frame Time stamping is implemented through pin 10 (DIG2), refer to
Section 11.6.
The Security Module (AES), Random Number Generator, High Data Rate Modes,
Frame Buffer Empty Indicator, Dynamic Frame Buffer Protection, Alternate Start-Of-
Frame Delimiter or Reduced Power Consumption Mode (RPC) do not require specific
circuitry to operate, for details refer to Section 11.1, Section 11.2, Section 11.3,
Section 11.7, Section 11.8, Section 11.9 and Section 11.10.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
19
6 Microcontroller Interface
6.1 Overview
This section describes the Atmel AT86RF233 to microcontroller interface. The interface
comprises a slave SPI and additional control signals; see Figure 6-1. The SPI timing
and protocol are described below.
Figure 6-1. Microcontroller to AT86RF233 Interface.
Microcontroller AT86RF233
/SEL
MOSI
MISO
SCLK
CLKM
IRQ
SLP_TR
MOSI
MISO
SCLK
GPIO1/CLK
GPIO2/IRQ
GPIO3
MOSI
MISO
SCLK
CLKM
IRQ
SLP_TR
/RST
GPIO4
SPI
/SEL /SEL
/RST
DIG2
GPIO5 DIG2
SPI - Master
SPI - Slave
Microcontrollers with a master SPI such as Atmel AVR family interface directly to the
AT86RF233. The SPI is used for register, Frame Buffer, SRAM and AES access. The
additional control signals are connected to the GPIO/IRQ interface of the
microcontroller. Table 6-1 introduces the radio transceiver I/O signals and their
functionality.
Table 6-1. Signal Description of Microcontroller Interface.
Signal Description
/SEL SPI select signal, active low
MOSI SPI data (master output slave input) signal
MISO SPI data (master input slave output) signal
SCLK SPI clock signal
CLKM Optional, Clock output, refer to Section 9.6.4, usable as:
- microcontroller clock source and/or MAC timer reference
- high precision timing reference
IRQ Interrupt request signal, further used as:
- Frame Buffer Empty indicator, refer to Section 11.7
SLP_TR Multi purpose control signal (functionality is state dependent, see Section 6.6):
- Sleep/Wakeup enable/disable SLEEP state
- Sleep/Wakeup enable/disable DEEP_SLEEP state
- TX start BUSY_TX_(ARET) state
/RST AT86RF233 reset signal, active low
DIG2 Optional,
- IRQ_2 (RX_START) for RX Frame Time Stamping, see Section 11.6
- Signals frame transmit within TX_ARET mode for TX Time Stamping
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
20
6.2 SPI Timing Description
Pin 17 (CLKM) can be used as a microcontroller master clock source. If the
microcontroller derives the SPI master clock (SCLK) directly from CLKM, the SPI
operates in synchronous mode, otherwise in asynchronous mode.
In asynchronous mode, the maximum SCLK frequency fasync is limited to 7.5MHz. The
signal at pin 17 (CLKM) is not required to derive SCLK and may be disabled to reduced
power consumption and spurious emissions.
Figure 6-2 and Figure 6-3 illustrate the SPI timing and introduces its parameters. The
corresponding timing parameter definitions t1 – t9 are defined in Section 12.4.
Figure 6-2. SPI Timing, Global Map and Definition of Timing Parameters t5, t6, t8, t9.
SCLK
t
8
MOSI
6
75432106
7543210
MISO
Bit 6Bit 5Bit 3Bit 2Bit 1Bit 0
Bit 4Bit 6Bit 5Bit 3Bit 2Bit 1Bit 0
Bit 4
Bit 7
t
6
Bit 7
t
5
/SEL
t
9
Figure 6-3. SPI Timing, Detailed Drawing of Timing Parameters t1 to t4.
Bit 7Bit 6
t
1
t
2
Bit 5
t
4
t
3
Bit 7Bit 6Bit 5
SCLK
MOSI
MISO
/SEL
The SPI is based on a byte-oriented protocol and is always a bidirectional
communication between the master and slave. The SPI master starts the transfer by
asserting /SEL = L. Then the master generates eight SPI clock cycles to transfer one
byte to the radio transceiver (via MOSI). At the same time, the slave transmits one byte
to the master (via MISO). When the master wants to receive one byte of data from the
slave, it must also transmit one byte to the slave. All bytes are transferred with the MSB
first. An SPI transaction is finished by releasing /SEL = H.
An SPI register access consists of two bytes, a Frame Buffer or SRAM access of at
least two or more bytes as described in Section 6.3.
/SEL = L enables the MISO output driver of the Atmel AT86RF233. The MSB of MISO
is valid after t1 (see Section 12.4) and is updated on each SCLK falling edge. If the
driver is disabled, there is no internal pull-up transistor connected to it. Driving the
appropriate signal level must be ensured by the master device or an external pull-up
resistor.
Note: 1. When both /SEL and /RST are active, the MISO output driver is also enabled.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
21
Referring to Figure 6-2 and Figure 6-3, Atmel AT86RF233 MOSI is sampled at the
rising edge of the SCLK signal and the output is set at the falling edge of SCLK. The
signal must be stable before and after the rising edge of SCLK as specified by t3 and t4,
refer to Section 12.4 parameters.
This SPI operational mode is commonly known as “SPI mode 0”.
6.3 SPI Protocol
Each SPI sequence starts with transferring a command byte from the SPI master via
MOSI (see Table 6-2) with the MSB first. This command byte defines the SPI access
mode and additional mode-dependent information.
Table 6-2. SPI Command Byte Definition.
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Access Mode Access Type
1 0 Register address [5:0] Register access
Read access
1 1 Register address [5:0] Write access
0 0 1 Reserved Frame Buffer access
Read access
0 1 1 Reserved Write access
0 0 0 Reserved SRAM access
Read access
0 1 0 Reserved Write access
Each SPI transfer returns bytes back to the SPI master on MISO output pin. The
content of the first byte (see value “PHY_STATUS“ in Figure 6-4 to Figure 6-14) is set
to zero after reset. To transfer status information of the radio transceiver to the
microcontroller, the content of the first byte can be configured with register bits
SPI_CMD_MODE (register 0x04, TRX_CTRL_1). For details, refer to Section 6.4.1.
Note: 1. Return values on MISO stated as XX shall be ignored by the microcontroller.
The different access modes are described within the following sections.
6.3.1 Register Access Mode
Register Access Mode is used to read and write AT86RF233 regsisters (register
address from 0x00 up to 0x3F).
A register access mode is a two-byte read/write operation initiated by /SEL = L. The first
transferred byte on MOSI is the command byte including an identifier bit (bit[7] = 1), a
read/write select bit (bit[6]), and a 6-bit register address.
On read access, the content of the selected register address is returned in the second
byte on MISO (see Figure 6-4).
Figure 6-4. Packet Structure - Register Read Access.
1ADDRESS[5:0]0 XXMOSI
PHY_STATUS
(1)
READ DATA[7:0]MISO
byte 1 (command byte)byte 2 (data byte)
Note: 1. Each SPI access can be configured to return radio controller status information
(PHY_STATUS) on MISO, for details refer to Section 6.4.
On write access, the second byte transferred on MOSI contains the write data to the
selected address (see Figure 6-5).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
22
Figure 6-5. Packet Structure - Register Write Access.
1ADDRESS[5:0]
1WRITE DATA[7:0]MOSI
PHY_STATUS XXMISO
byte 1 (command byte)byte 2 (data byte)
Each register access must be terminated by setting /SEL = H.
Figure 6-6 illustrates a typical SPI sequence for a register access sequence for write
and read respectively.
Figure 6-6. Example SPI Sequence – Register Access Mode.
PHY_STATUS XX PHY_STATUS READ DATA
WRITE COMMAND WRITE DATA READ COMMAND XX
Register Write Access Register Read Access
SCLK
MOSI
MISO
/SEL
6.3.2 Frame Buffer Access Mode
Frame Buffer Access Mode is used to read and write Atmel AT86RF233 frame buffer.
The frame buffer address is always reset to zero and incremented to access PSDU,
LQI, ED and RX_STATUS data.
The Frame Buffer can hold up to 128-byte of one PHY service data unit (PSDU)
IEEE 802.15.4 data frame. A detailed description of the Frame Buffer can be found in
Section 9.3. An introduction to the IEEE 802.15.4 frame format can be found in
Section 8.1.
Each access starts with /SEL = L followed by a command byte on MOSI. Each frame
read or write access command byte is followed by the PHR data byte, indicating the
frame length, followed by the PSDU data, see Figure 6-7 and Figure 6-8.
In Frame Buffer Access Mode during buffer reads, the PHY header (PHR) and the
PSDU data are transferred via MISO following PHY_STATUS byte. Once the PSDU
data is uploaded, three more bytes are transferred containing the link quality indication
(LQI) value, the energy detection (ED) value, and the status information (RX_STATUS)
of the received frame, for LQI details refer to Section 8.7. The Figure 6-7 illustrates the
packet structure of a Frame Buffer read access.
Note: 1. The frame buffer read access can be terminated immediately at any time by
setting pin 23 (/SEL) = H, for example after reading the PHR byte only.
Figure 6-7. Packet Structure - Frame Read Access.
0reserved[4:0]
0MOSI
PHY_STATUSMISO
byte 1 (command byte)
1XX
PHR[7:0]
byte 2 (data byte)
XX
PSDU[7:0]
byte 3 (data byte)
XX
ED[7:0]
byte n-1 (data byte)
XX
RX_STATUS[7:0]
byte n (data byte)
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
23
The structure of RX_STATUS is described in Table 6-3.
Table 6-3. Structure of RX_STATUS.
Bit
7
6
5
4
RX_CRC_VALID TRAC_STATUS RX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
reserved RX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
Note: 2. More information to RX_CRC_VALID, see Section 8.3.5, and to TRAC_STATUS,
see Section 7.2.6.
On frame buffer write access the second byte transferred on MOSI contains the frame
length (PHR field) followed by the payload data (PSDU) as shown by Figure 6-8.
Figure 6-8. Packet Structure - Frame Write Access.
0reserved[4:0]
1MOSI
PHY_STATUSMISO
byte 1 (command byte)
1PHR[7:0]
XX
byte 2 (data byte)
PSDU[7:0]
XX
byte 3 (data byte)
PSDU[7:0]
XX
byte n-1 (data byte)
PSDU[7:0]
XX
byte n (data byte)
The number of bytes n for one frame buffer access is calculated as follows:
Read Access: n = 5 + frame_length
[PHY_STATUS, PHR byte, PSDU data, LQI, ED, and RX_STATUS]
Write Access: n = 2 + frame_length
[command byte, PHR byte, and PSDU data]
The maximum value of frame_length is 127 bytes. That means that n ≤ 132 for Frame
Buffer read and n ≤ 129 for Frame Buffer write accesses.
Each read or write of a data byte automatically increments the address counter of the
Frame Buffer until the access is terminated by setting /SEL = H. A Frame Buffer read
access can be terminated at any time without any consequences by setting /SEL = H,
for example after reading the frame length byte only. A successive Frame Buffer read
operation starts again with the PHR field.
The content of the Atmel AT86RF233 Frame Buffer is overwritten by a new received
frame or a Frame Buffer write access.
Figure 6-9 and Figure 6-10 illustrate an example SPI sequence of a Frame Buffer
access to read a frame with 2-byte PSDU and write a frame with 4-byte PSDU.
Figure 6-9. Example SPI Sequence - Frame Buffer Read of a Frame with 2-byte PSDU.
COMMAND XX XX XX XX XX
PHY_STATUS PHR PSDU 2PSDU 1 EDLQI
XX
RX_STATUS
SCLK
MOSI
MISO
/SEL
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
24
Figure 6-10. Example SPI Sequence - Frame Buffer Write of a Frame with 4-byte PSDU.
COMMAND PHR PSDU 1PSDU 2PSDU 3PSDU 4
PHY_STATUS XX XX
XX XX
XX
SCLK
MOSI
MISO
/SEL
Access violations during a Frame Buffer read or write access are indicated by interrupt
IRQ_6 (TRX_UR). For further details, refer to Section 9.3.
Notes: 1. The Frame Buffer is shared between RX and TX operations, the frame data is
overwritten by freshly received data frames. If an existing TX payload data
frame is to be retransmitted, it must be ensured that no TX data is overwritten
by newly received RX data.
2. To avoid overwriting during receive Dynamic Frame Buffer Protection can be
enabled, refer to Section 11.8.
3.
For exceptions, receiving acknowledgement frames in Extended Operating
Mode (TX_ARET) refer to Section 7.2.4.
6.3.3 SRAM Access Mode
The SRAM access mode is used to read and write Atmel AT86RF233 frame buffer
beginning with a specified byte address. It enables to access dedicated buffer data
directly from a desired address without a need of incrementing the frame buffer from the
top.
The SRAM access mode allows accessing dedicated bytes within the Frame Buffer or
AES address space, refer to Section 11.1. This may reduce the SPI traffic.
During frame receive, after occurrence of IRQ_2 (RX_START), an SRAM access can
be used to upload the PHR field while preserving Dynamic Frame Buffer Protection, see
Section 11.8.
Each SRAM access starts with /SEL = L. The first transferred byte on MOSI shall be the
command byte and must indicate an SRAM access mode according to the definition in
Table 6-2. The following byte indicates the start address of the write or read access.
SRAM address space:
• Frame Buffer: 0x00 to 0x7F
• AES: 0x82 to 0x94
On SRAM read access, one or more bytes of read data are transferred on MISO
starting with the third byte of the access sequence; refer to Figure 6-11.
Figure 6-11. Packet Structure – SRAM Read Access.
0reserved[4:0]
0MOSI
PHY_STATUSMISO
byte 1 (command byte)
0ADDRESS[7:0]
XX
byte 2 (address)
XX
DATA[7:0]
byte 3 (data byte)
XX
DATA[7:0]
byte n-1 (data byte)
XX
DATA[7:0]
byte n (data byte)
On SRAM write access, one or more bytes of write data are transferred on MOSI
starting with the third byte of the access sequence; refer to Figure 6-12. Do not attempt
to read or write bytes beyond the SRAM buffer size.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
25
Figure 6-12. Packet Structure – SRAM Write Access.
0reserved[4:0]
1MOSI
PHY_STATUSMISO
byte 1 (command byte)
0ADDRESS[7:0]
XX
byte 2 (address)
DATA[7:0]
XX
byte 3 (data byte)
DATA[7:0]
XX
byte n-1 (data byte)
DATA[7:0]
XX
byte n (data byte)
As long as /SEL = L, every subsequent byte read or byte write increments the address
counter of the Frame Buffer until the SRAM access is terminated by /SEL = H.
Figure 6-13 and Figure 6-14 illustrate an example SPI sequence of an
Atmel AT86RF233 SRAM access to read and write a data package of five byte length,
respectively.
Figure 6-13. Example SPI Sequence – SRAM Read Access of a 5-byte Data Package.
COMMAND ADDRESS XX XX XX XX
PHY_STATUS XX DATA 2DATA 1DATA 4DATA 3
XX
DATA 5
SCLK
MOSI
MISO
/SEL
Figure 6-14. Example SPI Sequence – SRAM Write Access of a 5-byte Data Package.
COMMAND ADDRESS DATA 1DATA 2DATA 3DATA 4
PHY_STATUS XX XX
XX XX
XX
DATA 5
XX
SCLK
MOSI
MISO
/SEL
Notes: 1.
The SRAM access mode is not intended to be used as an alternative to the
Frame Buffer access modes (see Section 6.3.2).
2.
Frame Buffer access violations are not indicated by a TRX_UR interrupt when
using the SRAM access mode, for further details refer to Section 9.3.3.
6.4 Radio Transceiver Status information
Each Atmel AT86RF233 SPI access can return radio transceiver status information which
is a first byte transmitted out of MISO output as the serial data is being shifted into MOSI
input. Radio transceiver status information (PHY_STATUS) can be configured using
register bits SPI_CMD_MODE (register 0x04, TRX_CTRL_1) to return TRX_STATUS,
PHY_RSSI or IRQ_STATUS register as shown in below.
6.4.1 Register Description
Note: 1. Throughout this datasheet, underlined values indicate reset settings.
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
26
Figure 6-15. Register TRX_CTRL_1.
Bit 7 6 5 4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 3:2 - SPI_CMD_MODE
Each SPI transfer returns bytes back to the SPI master. The content of the first byte
(PHY_STATUS) can be configured using register bits SPI_CMD_MODE.
Table 6-4. SPI_CMD_MODE.
Register Bits Value Description
SPI_CMD_MODE 0 Default (empty, all bits zero)
1 Monitor TRX_STATUS register
2 Monitor PHY_RSSI register
3 Monitor IRQ_STATUS register
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
27
6.5 Radio Transceiver Identification
Atmel AT86RF233 can be identified by four registers. One 8-bit register contains a
unique part number (PART_NUM) and one register contains the corresponding 8-bit
version number (VERSION_NUM). Two additional 8-bit registers contain the JEDEC
manufacture ID.
6.5.1 Register Description
Register 0x1C (PART_NUM):
The register PART_NUM can be used for the radio transceiver identification and
includes the part number of the device.
Figure 6-16. Register PART_NUM.
Bit 7 6 5 4
0x1C
PART_NUM
PART_NUM
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x1C
PART_NUM
PART_NUM
Read/Write R R R R
Reset value
1 0 1 1
• Bit 7:0 - PART_NUM
Table 6-5. PART_NUM.
Register Bits Value Description
PART_NUM 0x0B AT86RF233 part number
Register 0x1D (VERSION_NUM):
The register VERSION_NUM can be used for the radio transceiver identification and
includes the version number of the device.
Figure 6-17. Register VERSION_NUM.
Bit
7
6
5
4
0x1D
VERSION_NUM
VERSION_NUM
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x1D
VERSION_NUM
VERSION_NUM
Read/Write
R
R
R
R
Reset value
0
0
0
1
• Bit 7:0 - VERSION_NUM
Table 6-6. VERSION_NUM.
Register Bits Value Description
VERSION_NUM 0x01 Revision A
0x02 Revision B
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
28
Register 0x1E (MAN_ID_0):
Part one of the JEDEC manufacturer ID.
Figure 6-18. Register MAN_ID_0.
Bit 7 6 5 4
0x1E
MAN_ID_0
MAN_ID_0
Read/Write R R R R
Reset value
0 0 0 1
Bit 3 2 1 0
0x1E
MAN_ID_0
MAN_ID_0
Read/Write R R R R
Reset value
1 1 1 1
• Bit 7:0 - MAN_ID_0
Table 6-7. MAN_ID_0.
Register Bits Value Description
MAN_ID_0 0x1F Atmel JEDEC manufacturer ID,
bits[7:0] of the 32-bit JEDEC manufacturer ID are stored in
register bits MAN_ID_0. Bits [15:8] are stored in register
0x1F (MAN_ID_1). The higher 16 bits of the ID are not
stored in registers.
Register 0x1F (MAN_ID_1):
Part two of the JEDEC manufacturer ID.
Figure 6-19. Register MAN_ID_1.
Bit
7
6
5
4
0x1F
MAN_ID_1
MAN_ID_1
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x1F
MAN_ID_1
MAN_ID_1
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - MAN_ID_1
Table 6-8. MAN_ID_1.
Register Bits Value Description
MAN_ID_1 0x00 Atmel JEDEC manufacturer ID,
bits[15:8] of the 32-bit JEDEC manufacturer ID are stored
in register bits MAN_ID_1. Bits [7:0] are stored in register
0x1E (MAN_ID_0). The higher 16 bits of the ID are not
stored in registers.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
29
6.6 Sleep/Wake-up and Transmit Signal (SLP_TR)
Pin 11 (SLP_TR) is a multi-functional pin. Its function relates to the current state of the
Atmel AT86RF233 and is summarized in Table 6-9. The radio transceiver states are
explained in detail in Chapter 7.
Table 6-9. SLP_TR Multi-functional Pin.
Transceiver Status Function Transition Description
PLL_ON TX start L H Starts frame transmission
TX_ARET_ON TX start L H Starts TX_ARET transaction
BUSY_RX_AACK TX start L H Starts ACK transmission during RX_AACK slotted operation, see
Section 7.2.3.4
TRX_OFF Sleep L H Takes the radio transceiver into SLEEP state, CLKM disabled
PREP_DEEP_SLEEP Deep Sleep L H Takes the radio transceiver into DEEP_SLEEP state, CLKM disabled
SLEEP Wakeup H L Takes the radio transceiver back into TRX_OFF state, level sensitive
DEEP_SLEEP Wakeup H L Takes the radio transceiver back into TRX_OFF state, level sensitive
In states PLL_ON and TX_ARET_ON, pin 11 (SLP_TR) is used as trigger input to
initiate a TX transaction. Here SLP_TR is sensitive on rising edge only.
After initiating a state change by a rising edge at pin 11 (SLP_TR) in radio transceiver
states TRX_OFF or PREP_DEEP_SLEEP, the radio transceiver remains in the new
state as long as the pin is logical high and returns to the preceding state with the falling
edge.
SLEEP state
The SLEEP state is used when radio transceiver functionality is not required, and thus
the AT86RF233 can be powered down to reduce the overall power consumption.
A power-down scenario is shown in Figure 6-20. When the radio transceiver is in
TRX_OFF state the microcontroller forces the AT86RF233 to SLEEP by setting
SLP_TR = H. If pin 17 (CLKM) provides a clock to the microcontroller this clock is
switched off after 35 CLKM cycles. This enables a microcontroller in a synchronous
system to complete its power-down routine and prevent deadlock situations. The
AT86RF233 awakes when the microcontroller releases pin 11 (SLP_TR). This concept
provides the lowest possible power consumption.
The CLKM clock frequency settings for 250kHz and 62.5kHz are not intended to directly
clock the microcontroller. When using these clock rates, CLKM is turned off immediately
when entering SLEEP state.
Figure 6-20. Sleep and Wake-up Initiated by Asynchronous Microcontroller Timer.
CLKM
SLP_TR
t
TR3
(35 CLKM clock cycles) CLKM off
t
TR1a
async timer elapses
(microcontroller)
Note: 1. Timing figures tTR3 and tTR1a refer to Table 7-1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
30
DEEP_SLEEP state
The DEEP_SLEEP state is used when radio transceiver functionality is not required,
and thus the Atmel AT86RF233 can be powered down to reduce the overall power
consumption.
When the radio transceiver is in PREP_DEEP_SLEEP state the microcontroller forces
the AT86RF233 to DEEP_SLEEP by setting SLP_TR = H. If pin 17 (CLKM) provides a
clock to the microcontroller this clock is switched off after 35 CLKM cycles. This enables
a microcontroller in a synchronous system to complete its power-down routine and
prevent deadlock situations. The AT86RF233 awakes when the microcontroller
releases pin 11 (SLP_TR) and goes into TRX_OFF state. This concept provides the
lowest possible power consumption.
The CLKM clock frequency settings for 250kHz and 62.5kHz are not intended to directly
clock the microcontroller. When using these clock rates, CLKM is turned off immediately
when entering DEEP_SLEEP state.
Note: 1.
After leaving the DEEP_SLEEP state the CLKM clock frequency is set back to
1MHz.
2. If the radio transceiver is in DEEP_SLEEP state the register contents are cleared.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
31
6.7 Interrupt Logic
6.7.1 Overview
Atmel AT86RF233 differentiates between nine interrupt events (eight physical interrupt
registers, one shared by two functions). Each interrupt is enabled by setting the
corresponding bit in the interrupt mask register 0x0E (IRQ_MASK). Internally, each
pending interrupt is flagged in the interrupt status register. All interrupt events are OR-
combined to a single external interrupt signal (IRQ pin). If an interrupt is issued,
pin 24 (IRQ) = H, the microcontroller shall read the interrupt status
register 0x0F (IRQ_STATUS) to determine the source of the interrupt. A read access to
this register clears the interrupt status register and thus the IRQ pin, too.
Interrupts are not cleared automatically when the event trigger for respective interrupt
flag bit in the register 0x0F (IRQ_STATUS) is no longer active. Only a read access to
register 0x0F (IRQ_STATUS) clears the flag bits. Exceptions are IRQ_0 (PLL_LOCK)
and IRQ_1 (PLL_UNLOCK) where each is cleared in addition by the appearance of the
other.
The supported interrupts for the Basic Operating Mode are summarized in Table 6-10.
Table 6-10. Interrupt Description in Basic Operating Mode.
IRQ Name Description Section
IRQ_7 (BAT_LOW) Indicates a supply voltage below the programmed threshold. 9.5.4
IRQ_6 (TRX_UR) Indicates a Frame Buffer access violation. 9.3.3
IRQ_5 (AMI) Indicates address matching. 8.2
IRQ_4 (CCA_ED_DONE) Multi-functional interrupt:
1. AWAKE_END:
• Indicates finished transition to TRX_OFF state from P_ON, SLEEP,
DEEP_SLEEP, or RESET state.
2. CCA_ED_DONE:
• Indicates the end of a CCA or ED measurement.
7.1.2.5
8.5.4
8.6.4
IRQ_3 (TRX_END) RX: Indicates the completion of a frame reception.
TX: Indicates the completion of a frame transmission.
7.1.3
7.1.3
IRQ_2 (RX_START) Indicates the start of a PSDU reception; the AT86RF233 state changed to BUSY_RX;
the PHR can be read from Frame Buffer.
7.1.3
IRQ_1 (PLL_UNLOCK) Indicates PLL unlock. If the radio transceiver is in BUSY_TX / BUSY_TX_ARET state,
the PA is turned off immediately.
9.7.5
IRQ_0 (PLL_LOCK) Indicates PLL lock. 9.7.5
Note: 1. The IRQ_4
(AWAKE_END) interrupt can usually not be seen when the
transceiver enters TRX_OFF state after P_ON, DEEP_SLEEP, or RESET,
because register
0x0E (IRQ_MASK) is reset to mask all interrupts. It is
recommended to enable IRQ_4 (AWAKE_END) to be not
ified once the
TRX_OFF state is entered.
The interrupt handling in Extended Operating Mode is described in Section 7.2.5.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
32
6.7.2 Interrupt Mask Modes and Pin Polarity
If register bit IRQ_MASK_MODE (register 0x04, TRX_CTRL_1) is set, an interrupt
event can be read from IRQ_STATUS register even if the interrupt itself is masked.
However, in that case no timing information for this interrupt is provided. The Table
6-11, Figure 6-21, and Figure 6-22 describes the function.
Table 6-11. IRQ Mask Configuration.
IRQ_MASK Value IRQ_MASK_MODE Description
0 0 IRQ is suppressed entirely and none of interrupt
sources are shown in register IRQ_STATUS.
0 1
IRQ is suppressed entirely but all interrupt
causes are shown in register IRQ_STATUS.
≠ 0 0
All enabled interrupts are signaled on IRQ pin
and are also shown in register IRQ_STATUS.
≠ 0 1
All enabled interrupts are signaled on IRQ pin
and all interrupt causes are shown in register
IRQ_STATUS.
Figure 6-21. IRQ_MASK_MODE = 0.
IRQ_MASK
(register 0x0E)
IRQ_STATUS
(register 0x0F) OR IRQ
Interrupt Sources
.
.
.
Figure 6-22. IRQ_MASK_MODE = 1.
OR IRQ
Interrupt Sources
IRQ_MASK
(register 0x0E)
.
.
.
IRQ_STATUS
(register 0x0F)
The Atmel AT86RF233 IRQ pin polarity can be configured with register bit
IRQ_POLARITY (register 0x04, TRX_CTRL_1). The default behavior is active high,
which means that pin 24 (IRQ) = H issues an interrupt request.
If the “Frame Buffer Empty Indicator” is enabled during Frame Buffer read access, the
IRQ pin has an alternative functionality, refer to Section 11.7 for details.
A solution to monitor the IRQ_STATUS register (without clearing it) is described in
Section 6.4.1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
33
6.7.3 Register Description
Register 0x0E (IRQ_MASK):
The IRQ_MASK register controls the interrupt signaling via pin 24 (IRQ).
Figure 6-23. Register IRQ_MASK.
Bit 7 6 5 4
0x0E
IRQ_MASK
IRQ_MASK
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x0E
IRQ_MASK
IRQ_MASK
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
• Bit 7:0 - IRQ_MASK
Mask register for interrupts. IRQ_MASK[7] correspondents to IRQ_7 (BAT_LOW).
IRQ_MASK[0] correspondents to IRQ_0 (PLL_LOCK).
Table 6-12. IRQ_MASK.
Register Bits Value Description
IRQ_MASK 0x00 The IRQ_MASK register is used to enable or disable
individual interrupts. An interrupt is enabled if the
corresponding bit is set to one. All interrupts are disabled
after power-on sequence (P_ON or DEEP_SLEEP state)
or reset (RESET state).
Valid values are [0xFF, 0xFE, …, 0x00].
Note: 1.
If an interrupt is enabled it is recommended to read the interrupt status register
0x0F (IRQ_STATUS) first to clear the history.
Register 0x0F (IRQ_STATUS):
The IRQ_STATUS register contains the status of the pending interrupt requests.
Figure 6-24. Register IRQ_STATUS.
Bit 7 6 5 4
0x0F IRQ_7_BAT_LOW IRQ_6_TRX_UR IRQ_5_AMI IRQ_4_CCA_ED_
DONE
IRQ_STATUS
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x0F IRQ_3_TRX_END IRQ_2_RX_
START
IRQ_1_PLL_
UNLOCK
IRQ_0_PLL_
LOCK
IRQ_STATUS
Read/Write R R R R
Reset value
0 0 0 0
For more information to meanings of interrupts, see Table 6-10 Interrupt Description in
Basic Operating Mode.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
34
By reading the register after an interrupt is signaled at pin 24 (IRQ) the source of the
issued interrupt can be identified. A read access to this register resets all interrupt bits,
and so clears the IRQ_STATUS register.
Notes: 1. If register bit IRQ_MASK_MODE (register 0x04,
TRX_CTRL_1) is set, an
interrupt event can be read from IRQ_STATUS register even if the interrupt
itself is masked; refer to Figure 6-22. However in that case no timing information
for this interrupt is provided.
2. If register bit IRQ_MASK_MODE (register 0x04,
TRX_CTRL_1) is set, it is
recommended to read the interrupt status register 0x0F (IRQ_STATUS) first to
clear the history.
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 6-25. Register TRX_CTRL_1.
Bit
7
6
5
4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON RX_BL_CTRL TRX_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
1
0
Bit
3
2
1
0
0x04 SPI_CMD_MODE IRQ_MASK_MODE IRQ_POLARITY TRX_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
1
0
• Bit 6 - IRQ_2_EXT_EN
The register bit IRQ_2_EXT_EN controls external signaling for time stamping via pin 10
(DIG2).
Table 6-13. IRQ_2_EXT_EN.
Register Bits Value Description
IRQ_2_EXT_EN 0 Time stamping over pin 10 (DIG2) is disabled
1(1) Time stamping over pin 10 (DIG2) is enabled
Notes: 1.
The pin 10 (DIG2) is also active if the corresponding interrupt event IRQ_2
(RX_START) mask bit in register 0x0E (IRQ_MASK) is set to zero.
2.
The pin remains at high level until the end of the frame receive or transmit
procedure.
The timing of a received frame can be determined by a separate pin 10 (DIG2). If
register bit IRQ_2_EXT_EN is set to one, the reception of a PHR field is directly issued
on pin 10 (DIG2), similar to interrupt IRQ_2 (RX_START).
For further details refer to Section 11.6.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
35
• Bit 1 - IRQ_MASK_MODE
The radio transceiver supports polling of interrupt events. Interrupt polling is enabled by
setting register bit IRQ_MASK_MODE.
Table 6-14. IRQ_MASK_MODE.
Register Bits Value Description
IRQ_MASK_MODE 0 Interrupt polling is disabled.
Masked off IRQ bits will not appear in IRQ_STATUS
register.
1 Interrupt polling is enabled.
Masked off IRQ bits will appear in IRQ_STATUS register.
With the interrupt polling enabled (IRQ_MASK_MODE = 1) the interrupt events are
flagged in the register 0x0F (IRQ_STATUS) when their respective mask bits are
disabled in the register 0x0E (IRQ_MASK).
• Bit 0 - IRQ_POLARITY
The register bit IRQ_POLARITY controls the polarity for pin 24 (IRQ). The default
polarity of the pin 24 (IRQ) is active high. The polarity can be configured to active low
via register bit IRQ_POLARITY.
Table 6-15. IRQ_POLARITY.
Register Bits Value Description
IRQ_POLARITY 0 Pin IRQ is high active
1 Pin IRQ is low active
Note: 1.
A modification of register bit IRQ_POLARITY has no influence to RX_BL_CTRL
behavior.
This setting does not affect the polarity of the “Frame Buffer Empty Indicator”, refer to
Section 11.7. The Frame Buffer Empty Indicator is always active high.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
36
7 Operating Modes
7.1 Basic Operating Mode
This section summarizes all states to provide the basic functionality of
Atmel AT86RF233, such as receiving and transmitting frames, the power-on sequence,
sleep, and deep sleep. The Basic Operating Mode is designed for IEEE 802.15.4 and
general ISM band applications; the corresponding radio transceiver states are shown in
Figure 7-1.
Figure 7-1. Basic Operating Mode State Diagram (for timing refer to Table 7-1).
PLL_ON
RX_ON
PLL_ON
TRX_OFF
(Clock State)
XOSC=ON
Pull=OFF
RX_ON
(all states except P_ON)
FORCE_TRX_OFF
(all states except SLEEP or
DEEP_SLEEP)
SHR
Detected
Frame
End
Frame
End BUSY_TX
(Transmit State)
PLL_ON
(PLL State)
TX_START
or
TRX_OFF
TRX_OFF
4
57
6
8
9
11
10
12 13 /RST = H
FORCE_PLL_ON
(all states except DEEP_SLEEP,
SLEEP, or P_ON)
14
SLP_TR = H
Legend:
Blue: SPI Write to Register TRX_STATE (0x02)
Red: Control signals via IC Pin
Green: Event
Basic Operating Mode States
State transition number, see Table 7-1
for timing
RX_ON
(Rx Listen State)
BUSY_RX
(Receive State)
RESET
X
(from all states)
/RST = L
2
TRX_OFF
SLP_TR = H
3
P_ON
(Power-on after V
DD
)
XOSC=ON
Pull=ON
SLEEP
(Sleep State)
XOSC=OFF
Pull=OFF
SLP_TR = L
DEEP_SLEEP
(Sleep State)
XOSC=OFF
Pull=ON
SLP_TR=H
XOSC=ON
Pull=OFF
PREP_
DEEP_SLEEP
(Prepare Sleep State)
SLP_TR=L
TRX_OFF
PREP_DEEP_SLEEP
15 16
17 18
19
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
37
7.1.1 State Control
The radio transceiver’s states are controlled by shifting serial digital data using the SPI
to write individual commands to the command register bits TRX_CMD (register 0x02,
TRX_STATE). Change of the transceiver state can also be triggered by driving directly
two signal pins: pin 11 (SLP_TR) and pin 8 (/RST). A successful state change can be
verified by reading the radio transceiver status from register bits TRX_STATUS
(register 0x01, TRX_STATUS).
If TRX_STATUS = 0x1F (STATE_TRANSITION_IN_PROGRESS) the Atmel
AT86RF233 is in a state transition. Do not try to initiate a further state change while the
radio transceiver is in STATE_TRANSITION_IN_PROGRESS.
Pin 11 (SLP_TR) is a multifunctional pin, refer to Section 6.6. Depending on the radio
transceiver state, a rising edge of pin 11 (SLP_TR) causes the following state
transitions:
• TRX_OFF SLEEP (level sensitive)
• PLL_ON BUSY_TX
• PREP_ DEEP_SLEEP DEEP_SLEEP (level sensitive)
Whereas the falling edge of pin SLP_TR causes the following state transitions:
• SLEEP TRX_OFF (level sensitive)
• DEEP_SLEEP TRX_OFF (level sensitive)
A low level on pin 8 (/RST) causes a reset of all registers (register bits CLKM_CTRL are
shadowed, for details, refer to Section 9.6.4) and forces the radio transceiver into
TRX_OFF state. However, if the device was in P_ON state it remains in the P_ON
state.
For all states except SLEEP and DEEP_SLEEP, the state change commands
FORCE_TRX_OFF or TRX_OFF lead to a transition into TRX_OFF state. If the radio
transceiver is in active receive or transmit states (BUSY_*), the command
FORCE_TRX_OFF interrupts these active processes, and forces an immediate
transition to TRX_OFF. In contrast a TRX_OFF command is stored until an active state
(receiving or transmitting) has been finished. After that the transition to TRX_OFF is
performed.
For a fast transition from any non sleep states to PLL_ON state the command
FORCE_PLL_ON is provided. Active processes are interrupted. In contrast to
FORCE_TRX_OFF, this command does not disable PLL and analog voltage regulator
(AVREG). It is not available in states P_ON, SLEEP, DEEP_SLEEP, or RESET.
The completion of each requested state change shall always be confirmed by reading
the register bits TRX_STATUS (register 0x01, TRX_STATUS).
Note: 1.
If FORCE_TRX_OFF and FORCE_PLL_ON commands are used, it is
recommended to set pin 11 (SLP_TR) = L before.
7.1.2 Basic Operating Mode Description
7.1.2.1 P_ON – Power-On after VDD
When the external supply voltage (VDD) is firstly applied to the AT86RF233, the radio
transceiver goes into P_ON state performing an on-chip reset. The crystal oscillator is
activated and the default 1MHz master clock is provided at pin 17 (CLKM) after the
crystal oscillator has stabilized. CLKM can be used as a clock source to the
microcontroller. The SPI interface and digital voltage regulator (DVREG) are enabled.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
38
The on-chip power-on-reset sets all registers to their default values. A dedicated reset
signal from the microcontroller at pin 8 (/RST) is not necessary, but recommended for
hardware / software synchronization reasons.
All digital inputs are pulled-up or pulled-down during P_ON state, refer to Section 1.3.2.
This is necessary to support microcontrollers where GPIO signals are floating after
power-on or reset. The input pull-up and pull-down transistors are disabled when the
radio transceiver leaves P_ON state towards TRX_OFF state. A reset during P_ON
state does not change the pull-up and pull-down configuration.
Leaving P_ON state, output pins DIG1/DIG2 are pulled-down to digital ground, whereas
pins DIG3/DIG4 are pulled-down to analog ground, unless their configuration is
changed.
Prior to leaving P_ON, the microcontroller must set the Atmel AT86RF233 pins to the
default operating values: pin 11 (SLP_TR) = L, pin 8 (/RST) = H and pin 23 (/SEL) = H.
All interrupts are disabled by default. Thus, interrupts for state transition control are to
be enabled first, for example enable IRQ_4 (AWAKE_END) to indicate a state transition
to TRX_OFF state or interrupt IRQ_0 (PLL_LOCK) to signal a locked PLL in PLL_ON
state. In P_ON state a first access to the radio transceiver registers is possible after a
default 1MHz master clock is provided at pin 17 (CLKM), refer to tTR1 to Table 7-1.
Once the supply voltage has stabilized and the crystal oscillator has settled (see
parameter tXTAL refer to Table 7-2), the interrupt mask for the AWAKE_END should be
set. A valid SPI write access to register bits TRX_CMD (register 0x02, TRX_STATE)
with the command TRX_OFF or FORCE_TRX_OFF initiate a state change from P_ON
towards TRX_OFF state, which is then indicated by an interrupt IRQ_4 (AWAKE_END)
if enabled.
7.1.2.2 SLEEP – Sleep State
In SLEEP state, the radio transceiver is disabled. No circuitry is operating beyond the
circuitry monitoring pin 11 (SLP_TR) and pin 8 (/RST). This state can only be entered
from state TRX_OFF, by setting the SLP_TR = H.
If CLKM is enabled with a clock rates higher than 250kHz, the SLEEP state is entered
35 CLKM cycles after the rising edge at pin 11 (SLP_TR). At that time CLKM is turned
off. If the CLKM output is already turned off (register bits CLKM_CTRL = 0), the SLEEP
state is entered immediately. At clock rates 250kHz and 62.5kHz, the main clock at
pin 17 (CLKM) is turned off immediately.
Setting SLP_TR = L returns the radio transceiver back to the TRX_OFF state. During
SLEEP state the radio transceiver register contents and the AES register contents
remain valid while the contents of the Frame Buffer are lost.
/RST = L in SLEEP state returns the radio transceiver to TRX_OFF state and thereby
sets all registers to their default values. Exceptions are register bits CLKM_CTRL
(register 0x03, TRX_CTRL_0). These register bits require a specific treatment, for
details see Section 9.6.4.
7.1.2.3 PREP_DEEP_SLEEP – Deep Sleep Preparation State
The state PREP_DEEP_SLEEP is the preparation state for DEEP_SLEEP state. The
state can be reached by writing the command PREP_DEEP_SLEEP to register bits
TRX_CMD (register 0x02, TRX_STATE).
If CLKM is enabled with a clock rates higher than 250kHz, the DEEP_SLEEP state is
entered 35 CLKM cycles after the rising edge at pin 11 (SLP_TR). At that time CLKM is
turned off. If the CLKM output is already turned off (register bits CLKM_CTRL = 0), the
DEEP_SLEEP state is entered immediately. At clock rates 250kHz and 62.5kHz, the
main clock at pin 17 (CLKM) is turned off immediately.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
39
7.1.2.4 DEEP_SLEEP – Deep Sleep State
In DEEP_SLEEP state, the entire radio transceiver is disabled. No circuitry is operating
beyond the circuitry monitoring pin 11 (SLP_TR). The radio transceiver current
consumption is reduced to leakage current only. This state can only be entered from
state PREP_DEEP_SLEEP, by setting the SLP_TR = H.
Setting SLP_TR = L returns the radio transceiver back to the TRX_OFF state. After
DEEP_SLEEP state the radio transceiver register contents and the AES register
contents obtain the reset values while the contents of the Frame Buffer are lost. The
CLKM starts with the default 1MHz master clock at pin 17 (CLKM) after the crystal
oscillator has stabilized.
All Atmel AT86RF233 digital inputs are pulled-up or pulled-down during DEEP_SLEEP
state, refer to Section 1.3.2, except SLP_TR.
7.1.2.5 TRX_OFF – Clock State
In TRX_OFF the crystal oscillator is running and the master clock is available if
enabled. The SPI interface and digital voltage regulator are enabled, thus the radio
transceiver registers, the Frame Buffer and security engine (AES) are accessible (see
Section 9.3 and Section 11.1).
In contrast to P_ON state the pull-up and pull-down configuration is disabled.
Notes: 1. Pin 11 (SLP_TR) and pin 8 (/RST) are available for state control.
2. The analog front-end is disabled during TRX_OFF state.
Entering the TRX_OFF state from P_ON, SLEEP, DEEP_SLEEP or RESET state is
indicated by interrupt IRQ_4 (AWAKE_END) if enabled.
7.1.2.6 PLL_ON – PLL State
Entering the PLL_ON state from TRX_OFF state enables the analog voltage regulator
(AVREG) first. After the voltage regulator has been settled (see Table 7-2), the PLL
frequency synthesizer is enabled. When the PLL has been settled at the receive
frequency to a channel defined by register bits CHANNEL (register 0x08,
PHY_CC_CCA) or register bits CC_NUMBER (register 0x13, CC_CTRL_0) and
CC_BAND (register 0x14, CC_CTRL_1), refer to Section 9.7.2, a successful PLL lock is
indicated by issuing an interrupt IRQ_0 (PLL_LOCK).
If an RX_ON command is issued in PLL_ON state, the receiver is enabled immediately.
If the PLL has not been settled before the state change nevertheless takes place. Even
if the register bits TRX_STATUS (register 0x01, TRX_STATUS) indicates RX_ON,
actual frame reception can only start once the PLL has locked.
The PLL_ON state corresponds to the TX_ON state in IEEE 802.15.4.
7.1.2.7 RX_ON and BUSY_RX – RX Listen and Receive State
In RX_ON state the receiver is in the RX data polling mode and the PLL frequency
synthesizer is locked to its preprogrammed frequency.
The Atmel AT86RF233 receive mode is internally separated into RX_ON state and
BUSY_RX state. There is no difference between these states with respect to the analog
radio transceiver circuitry, which are always turned on. In both states, the receiver and
the PLL frequency synthesizer are enabled.
During RX_ON state, the receiver listens for incoming frames. After detecting a valid
synchronization header (SHR), the Atmel AT86RF233 automatically enters the
BUSY_RX state. The reception of a valid PHY header (PHR) generates an
IRQ_2 (RX_START) if enabled.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
40
During PSDU reception, the frame data are stored continuously in the Frame Buffer
until the last byte was received. The completion of the frame reception is indicated by
an interrupt IRQ_3 (TRX_END) and the radio transceiver reenters the state RX_ON. At
the same time the register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is updated
with the result of the FCS check (see Section 8.3).
Received frames are passed to the frame filtering unit, refer to Section 8.2. If the
content of the MAC addressing fields (refer to [2] IEEE 802.15.4-2006 Section 7.2.1)
generates a match, IRQ_5 (AMI) interrupt is issued, refer to Section 6.7. The expected
address values are to be stored in registers 0x20 – 0x2B (Short address, PAN-ID and
IEEE address). Frame filtering is available in Basic Operating Mode and Extended
Operating Mode, refer to Section 8.2.
Leaving state RX_ON is possible by writing a state change command to register bits
TRX_CMD in register 0x02 (TRX_STATE).
7.1.2.8 BUSY_TX – Transmit State
In the BUSY_TX state AT86RF233 is in the data transmission state.
A transmission can only be initiated from the PLL_ON state. The transmission can be
started either by driving event such as:
• A rising edge on pin 11 (SLP_TR), or
• A serial TX_START command via the SPI to register bits TRX_CMD (register 0x02,
TRX_STATE).
Either of these takes the radio transceiver into the BUSY_TX state. Refer to
Section 10.2 for more details.
During the transition to the BUSY_TX state, the PLL frequency shifts to the transmit
frequency, refer to Section 9.7.3. The actual transmission of the first data chip of the
SHR starts after 16µs to allow PLL settling and PA ramp-up, see Figure 7-7. After
transmission of the SHR, the Frame Buffer content is transmitted. In case the PHR
indicates a frame length of zero, the transmission is aborted immediately after the PHR
field.
After the frame transmission has been completed, the AT86RF233 automatically turns
off the power amplifier, generates an IRQ_3 (TRX_END) interrupt and returns into
PLL_ON state.
7.1.2.9 RESET State
The RESET state is used to set back the state machine and to reset all registers of
Atmel AT86RF233 to their default values; exceptions are register bits CLKM_CTRL
(register 0x03, TRX_CTRL_0). These register bits require a specific treatment, for
details see Section 9.6.4.
Once in RESET state a device enters TRX_OFF state by setting pulling a reset pin high
pin 8 (/RST) = H. If the device is still in the P_ON state it remains in the P_ON state
though. A reset is triggered by pulling /RST pin low pin 8 (/RST) = L and the state
returns after setting /RST = H. The reset pulse should have a minimum length as
specified in Section 7.1.4.6 and Section 12.4 (parameter t10). During reset, the
microcontroller has to set the radio transceiver control pins SLP_TR and /SEL to their
default values.
An overview about the register reset values is provided in Table 14-2.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
41
7.1.3 Interrupt Handling
All interrupts provided by the Atmel AT86RF233 (see Table 6-10) are supported in
Basic Operating Mode. For example, interrupts are provided to observe the status of
radio transceiver RX and TX operations.
When being in receive mode, IRQ_2 (RX_START) indicates the detection of a valid
PHR first, IRQ_5 (AMI) an address match, and IRQ_3 (TRX_END) the completion of
the frame reception. During transmission, IRQ_3 (TRX_END) indicates the completion
of the frame transmission.
Figure 7-2 shows an example for a transmit/receive transaction between two devices
and the related interrupt events in Basic Operating Mode. Device 1 transmits a frame
containing a MAC header (in this example of length seven), MAC payload, and a valid
FCS. The end of the frame transmission is indicated by IRQ_3 (TRX_END).
The frame is received by Device 2. Interrupt IRQ_2 (RX_START) indicates the
detection of a valid PHR field and IRQ_3 (TRX_END) the completion of the frame
reception. If the frame passes the Frame Filter (refer to Section 8.2), an address match
interrupt IRQ_5 (AMI) is issued after the reception of the MAC header (MHR). The
received frame is stored in the Frame Buffer.
In Basic Operating Mode the third interrupt IRQ_3 (TRX_END) is issued at the end of
the received frame. In Extended Operating Mode, refer to Section 7.2; the interrupt is
only issued if the received frame passes the address filter and the FCS is valid. Further
exceptions are explained in Section 7.2.
Processing delay tIRQ is a typical value, refer to Section 12.4.
Figure 7-2. Timing of RX_START, AMI and TRX_END Interrupts in Basic Operating Mode.
128 160 1920 192+(9+m)*32-16 Time [µs]
RX
(Device 2)
IRQ_2 (RX_START)
tIRQ
RX_ON RX_ON
IRQ
TRX_STATE
Interrupt latency
TRX_ENDIRQ_5 (AMI)
tIRQ tIRQ
BUSY_RX
IRQ_3 (TRX_END)
TX
(Device1)
PLL_ON BUSY_TX PLL_ON
IRQ
SLP_TR
TRX_STATE
Typ. Processing Delay
Frame
on Air
Preamble SFD PHR MSDU
4 1 1 mNumber of Octets
Frame Content MHR
7
FCS
2
tTR10
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
42
7.1.4 Basic Operating Mode Timing
This section depicts Atmel AT86RF233 state transitions and their timing properties.
Timing figures are explained in Table 7-1, Table 7-2, and Section 12.4.
7.1.4.1 Power-on Procedure
The power-on procedure to P_ON state is shown in Figure 7-3.
Figure 7-3. Power-on Procedure to P_ON State.
0
Event
State
VDD on
P_ON
Block XOSC, DVREG
100
CLKM on
400 Time [µs]
Time tTR1
When the external supply voltage (VDD) is initially supplied to the AT86RF233, the radio
transceiver enables the crystal oscillator (XOSC) and the internal 1.8V voltage regulator
for the digital domain (DVREG). After tTR1 = 330µs (typ.), the master clock signal is
available at pin 17 (CLKM) at default rate of 1MHz. As soon as CLKM is available the
SPI is enabled and can be used to control the transceiver. As long as no state change
towards state TRX_OFF is performed, the radio transceiver remains in P_ON state.
7.1.4.2 Wake-up Procedure from SLEEP
The wake-up procedure from SLEEP state is shown in Figure 7-4.
Figure 7-4. Wake-up Procedure from SLEEP State.
0
Event
State
Block
CLKM on
Time [μs]
Time t
TR2
TRX_OFF
IRQ_4 (AWAKE_END)SLP_TR = L
SLEEP
XOSC, DVREG XOSC, DVREGFTN
200
The radio transceiver’s SLEEP state is left by releasing pin 11 (SLP_TR) to logic low.
This restarts the XOSC and DVREG. After tTR2 = 210µs (typ.) the radio transceiver
enters TRX_OFF state. The internal clock signal is available and provided to
pin 17 (CLKM), if enabled.
This procedure is similar to the Power-on Procedure. However the radio transceiver
automatically proceeds to the TRX_OFF state. During this, transition the filter-tuning
network (FTN) calibration is performed. Entering TRX_OFF state is signaled by
IRQ_4 (AWAKE_END), if this interrupt was enabled by the appropriate mask register
bit.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
43
7.1.4.3 Wake-up Procedure from DEEP_SLEEP
The wake-up procedure from DEEP_SLEEP state is shown in Figure 7-5.
Figure 7-5. Wake-up Procedure from DEEP_SLEEP State.
0
Event
State
Block
CLKM on
Time [μs]
Time t
TR18
TRX_OFF
IRQ_4 (AWAKE_END)SLP_TR = L
DEEP_
SLEEP
XOSC, DVREG XOSC, DVREG
FTN
350
The Atmel AT86RF233 radio transceiver’s DEEP_SLEEP state is left by releasing
SLP_TR pin to logic low. This restarts the XOSC and DVREG. After tTR18 = 360µs (typ.)
the radio transceiver enters TRX_OFF state. The internal clock signal is available and
provided default rate of 1MHz clock to pin 17 (CLKM).
This procedure is similar to the Power-on Procedure. However the radio transceiver
automatically proceeds to the TRX_OFF state. During this, transition the filter-tuning
network (FTN) calibration is performed.
7.1.4.4 PLL_ON and RX_ON States
The transition from TRX_OFF to PLL_ON or RX_ON mode is shown in Figure 7-6.
Figure 7-6. Transition from TRX_OFF to PLL_ON or RX_ON state.
0
Event
State
Block
80 Time [µs]
Time
tTR4
IRQ_0 (PLL_LOCK)
TRX_OFF
AVREG
Command
PLL_ON
PLL RX
PLL_ON
RX_ON
tTR8
RX_ON
Notes: 1. If TRX_CMD = RX_ON in TRX_OFF state RX_ON state is entered immediately,
even if the PLL has not settled.
2. Timing figures tTR4 and tTR8 refers to Table 7-1.
In TRX_OFF state, entering the commands PLL_ON or RX_ON initiates a ramp-up
sequence of the internal 1.8V voltage regulator for the analog domain (AVREG).
RX_ON state can be entered any time from PLL_ON state, regardless whether the PLL
has already locked, which is indicated by IRQ_0 (PLL_LOCK). Likewise, PLL_ON state
can be entered any time from RX_ON state.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
44
7.1.4.5 BUSY_TX to RX_ON States
The transition from PLL_ON to BUSY_TX state and subsequently to RX_ON state is
shown in Figure 7-7.
Figure 7-7. PLL_ON to BUSY_TX to RX_ON Timing.
Time [µs]0 x16 x + 32
Time
t
TR11
t
TR10
Command
RX_ON
State
Block
PLL_ON RX_ONBUSY_TX
Pin
SLP_TR
PA PLLPA, TX RXPLL
or command TX_START
Starting from PLL_ON state, it is further assumed that the PLL has already been
locked. A transmission is initiated either by a rising edge of pin 11 (SLP_TR) or by
command TX_START. The PLL settles to the transmit frequency and the PA is
enabled. After the duration of tTR10 = 16µs, the Atmel AT86RF233 changes into
BUSY_TX state, transmitting the internally generated SHR and the PSDU data of the
Frame Buffer. After completing the frame transmission, indicated by
IRQ_3 (TRX_END), the PLL settles back to the receive frequency within tTR11 = 32µs
and returns to state PLL_ON.
If during BUSY_TX the radio transmitter is requested to change to a receive state, it
automatically proceeds to state RX_ON upon completion of the transmission.
7.1.4.6 Reset Procedure
The radio transceiver reset procedure is shown in Figure 7-8.
Figure 7-8. Reset Procedure.
x
Event
State
Block
Time [μs]
Pin /RST
TRX_OFF
x + 30
[IRQ_4 (AWAKE_END)]
0
various
Time
>t
10
t
TR13
>t
11
XOSC, DVREG XOSC, DVREG
x + 10
FTN
Note: 1. Timing figure tTR13 refers to Table 7-1, t10, t11 refers to Section 12.4.
/RST = L sets all registers to their default values. Exceptions are register bits
CLKM_CTRL (register 0x03, TRX_CTRL_0), refer to Section 9.6.4. After releasing the
reset pin 8 (/RST) = H, the wake-up sequence including an FTN calibration cycle is
performed, refer to Section 9.8. After that the TRX_OFF state is entered.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
45
Figure 7-8 illustrates the reset procedure once P_ON state was left and the radio
transceiver was not in SLEEP or DEEP_SLEEP state.
The reset procedure is identical for all originating radio transceiver states except of
state P_ON, SLEEP, or DEEP_SLEEP. Instead, the procedures described in
Section 7.1.2.1 must be followed to enter the TRX_OFF state.
If the radio transceiver was in state SLEEP or DEEP_SLEEP, the XOSC and DVREG
are enabled before entering TRX_OFF state.
If register bits TRX_STATUS indicates STATE_TRANSITION_IN_PROGRESS during
system initialization until the Atmel AT86RF233 reaches TRX_OFF state, do not try to
initiate a further state change while the radio transceiver is in this state.
Notes: 2. The reset impulse should have a minimum length t10 = 625ns as specified in
Section 12.4.
3. An access to the device should not occur earlier than t11 ≥ 625ns after releasing
the /RST pin; refer to Section 12.4.
4. A reset overrides an SPI command request that might have been queued.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
46
7.1.4.7 State Transition Timing Summary
The Atmel AT86RF233 transition numbers correspond to Figure 7-1 and do not include
SPI access time unless otherwise stated. See measurement setup in Figure 5-1.
Table 7-1. State Transition Timing.
Symbol Parameter Condition Min. Typ. Max. Unit
tTR1 P_ON⇒CLKM is available Depends on crystal oscillator
setup (CL= 10pF) and external
capacitor at DVDD (100nF nom.).
330 1000 µs
tTR1a SLEEP⇒CLKM is available Depends on crystal oscillator
setup (CL= 10pF) and external
capacitor at DVDD (100nF nom.).
180 1000 µs
tTR1b DEEP_SLEEP⇒CLKM is available Depends on crystal oscillator
setup (CL= 10pF) and external
capacitor at DVDD (100nF nom.).
330 1000 µs
tTR2 SLEEP⇒TRX_OFF Depends on crystal oscillator
setup (CL= 10pF) and external
capacitor at DVDD (100nF nom.).
210 1000 µs
tTR3 TRX_OFF⇒SLEEP For fCLKM > 250kHz. 35 CLKM
cycles
Otherwise. 0 CLKM
cycles
tTR4 TRX_OFF⇒PLL_ON Depends on external capacitor at
AVDD (100nF nom.).
80 µs
tTR5 PLL_ON⇒TRX_OFF 1 µs
tTR6 TRX_OFF⇒RX_ON Depends on external capacitor at
AVDD (100nF nom.).
80 µs
tTR7 RX_ON⇒TRX_OFF 1 µs
tTR8 PLL_ON⇒RX_ON 1 µs
tTR9 RX_ON⇒PLL_ON Transition time is also valid for
TX_ARET_ON, RX_AACK_ON.
1 µs
tTR10 PLL_ON⇒BUSY_TX When asserting pin 11 (SLP_TR)
or TRX_CMD = TX_START first
symbol transmission is delayed by
one symbol period (PLL settling
and PA ramp-up).
16 µs
tTR11 BUSY_TX⇒PLL_ON PLL settling time. 32 µs
tTR12 Various states⇒TRX_OFF Using TRX_CMD =
FORCE_TRX_OFF; not valid for
SLEEP or DEEP_SLEEP.
1 µs
tTR13 RESET⇒TRX_OFF Not valid for P_ON, SLEEP, or
DEEP_SLEEP.
26 µs
tTR14 Various states⇒PLL_ON Using TRX_CMD =
FORCE_PLL_ON; not valid for
P_ON, SLEEP, DEEP_SLEEP, or
RESET.
1 µs
tTR15 P_ON⇒TRX_OFF Using TRX_CMD = TRX_OFF
directly after CLKM is available.
360 1000 µs
tTR16 PREP_DEEP_SLEEP⇒TRX_OFF 1 µs
tTR17 TRX_OFF⇒PREP_DEEP_SLEEP 1 µs
tTR18 DEEP_SLEEP⇒TRX_OFF Depends on crystal oscillator
setup (CL= 10pF) and external
capacitor at DVDD (100nF nom.).
360 1000 µs
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
47
Symbol Parameter Condition Min. Typ. Max. Unit
tTR19 PREP_DEEP_SLEEP⇒DEEP_SLEEP For fCLKM > 250kHz. 35 CLKM
cycles
Otherwise. 0 CLKM
cycles
The state transition timing is calculated based on the timing of the individual blocks
shown in Figure 7-3 to Figure 7-8. The worst case values include maximum operating
temperature, minimum supply voltage, and device parameter variations.
Table 7-2. Block Initialization and Settling Time.
Symbol Parameter Condition Min. Typ. Max. Unit
tXTAL Reference oscillator settling time Start XTAL⇒clock available at pin
17 (CLKM). Depends on crystal Q
factor and load capacitor.
330 1000 µs
tFTN FTN calibration time 25 µs
tDVREG DVREG settling time Depends on external bypass
capacitor at DVDD (CB3 = 100nF
nom., 10µF worst case).
50 1000 µs
tAVREG AVREG settling time Depends on external bypass
capacitor at AVDD (CB1 = 100nF
nom., 10µF worst case).
50 1000 µs
tPLL_INIT Initial PLL settling time PLL settling time
TRX_OFF⇒PLL_ON, including
40µs AVREG settling time.
80 250 µs
tPLL_SW PLL settling time on channel switch Duration of channel switch within
frequency band.
11 100 µs
tPLL_CF PLL CF calibration PLL center frequency calibration. 8 8 24 µs
tPLL_DCU PLL DCU calibration PLL DCU calibration. 6 6 µs
tRX_TX RX⇒TX Maximum settling time RX⇒TX. 16 µs
tTX_RX TX⇒RX Maximum settling time TX⇒RX. 32 µs
tSHR_SYNC SHR, sync SHR synchronization period. 32 96 160 µs
tRSSI RSSI, update RSSI update period in receive
states.
2 µs
tED ED measurement ED measurement period is eight
symbols.
135 180 µs
tCCA CCA measurement CCA measurement period is eight
symbols.
135 180 µs
tRND Random value, update Random value update period. 1 µs
tAES AES core cycle time 23.4 24 µs
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
48
7.1.5 Register Description
Register 0x01 (TRX_STATUS):
The read-only register TRX_STATUS signals the present state of the radio transceiver
as well as the status of a CCA operation.
Figure 7-9. Register TRX_STATUS.
Bit 7 6 5 4
0x01
CCA_DONE
CCA_STATUS
reserved
TRX_STATUS
TRX_STATUS
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x01
TRX_STATUS
TRX_STATUS
Read/Write R R R R
Reset value
0 0 0 0
• Bit 4:0 - TRX_STATUS
The register bits TRX_STATUS signal the current radio transceiver status.
Table 7-3. TRX_STATUS.
Register Bits Value Description
TRX_STATUS 0x00 P_ON
0x01 BUSY_RX
0x02 BUSY_TX
0x06 RX_ON
0x08 TRX_OFF (CLK Mode)
0x09 PLL_ON (TX_ON)
0x0F(1) SLEEP
0x10 PREP_DEEP_SLEEP
0x11(2) BUSY_RX_AACK
0x12(2) BUSY_TX_ARET
0x16(2) RX_AACK_ON
0x19(2) TX_ARET_ON
0x1F(3) STATE_TRANSITION_IN_PROGRESS
All other values are reserved
Notes: 1. In SLEEP or DEEP_SLEEP state register not accessible.
2. Extended Operating Mode only.
3.
Do not try to initiate a further state change while the radio transceiver is in
STATE_TRANSITION_IN_PROGRESS state.
A read access to register bits TRX_STATUS reflects the current radio transceiver state.
A state change is initiated by writing a state transition command to register bits
TRX_CMD (register 0x02, TRX_STATE). Alternatively, some state transitions can be
initiated by the rising edge of pin 11 (SLP_TR) in the appropriate state.
These register bits are used for Basic and Extended Operating Mode, see Section 7.2.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
49
If the requested state transition has not been completed, the TRX_STATUS returns
STATE_TRANSITION_IN_PROGRESS value. Do not try to initiate a further state
change while the radio transceiver is in STATE_TRANSITION_IN_PROGRESS state.
State transition timings are defined in Table 7-1.
Register 0x02 (TRX_STATE):
The radio transceiver states are advanced via register TRX_STATE by writing a
command word into register bits TRX_CMD. The read-only register bits
TRAC_STATUS indicate the status or result of an Extended Operating Mode
transaction.
Figure 7-10. Register TRX_STATE.
Bit
7
6
5
4
0x02 TRAC_STATUS TRX_CMD TRX_STATE
Read/Write
R
R
R
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x02 TRX_CMD TRX_STATE
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 4:0 - TRX_CMD
A write access to register bits TRX_CMD initiate a radio transceiver state transition to
the new state.
Table 7-4. TRX_CMD.
Register Bits Value Description
TRX_CMD 0x00(1) NOP
0x02(2) TX_START
0x03 FORCE_TRX_OFF
0x04(3) FORCE_PLL_ON
0x06 RX_ON
0x08 TRX_OFF (CLK Mode)
0x09 PLL_ON (TX_ON)
0x10 PREP_DEEP_SLEEP
0x16(4) RX_AACK_ON
0x19(4) TX_ARET_ON
All other values are reserved
Notes: 1. TRX_CMD = “0” after power on reset (POR).
2. The frame transmission starts one symbol after TX_START command.
3.
FORCE_PLL_ON is not valid for states P_ON, SLEEP, DEEP_SLEEP, and
RESET, as well as STATE_TRANSITION_IN_PROGRESS towards these states.
4. Extended Operating Mode only.
A write access to register bits TRX_CMD initiates a radio transceiver state transition
towards the new state.
These register bits are used for Basic and Extended Operating Mode, see Section 7.2.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
50
7.2 Extended Operating Mode
Extended Operating Mode makes up for a large set of automated functionality add-ons
which can be referred to as a hardware MAC accelerator. These add-ons go beyond
the basic radio transceiver functionality provided by the Basic Operating Mode.
Extended Operating Mode functions handle time critical MAC tasks, requested by the
IEEE 802.15.4 standard, in hardware, such as automatic acknowledgement, automatic
CSMA-CA, and retransmission. This results in a more efficient IEEE 802.15.4 software
MAC implementation, including reduced code size, and may allow use of a smaller
microcontroller or operation at low clock rates.
The Extended Operating Mode is designed to support IEEE 802.15.4-2006 and
IEEE 802.15.4-2011 compliant frames; the mode is backward compatible to
IEEE 802.15.4-2003 and supports non IEEE 802.15.4 compliant frames. This mode
comprises the following procedures:
Automatic acknowledgement (RX_AACK) divides into the tasks:
• Frame reception and automatic FCS check
• Configurable addressing fields check
• Interrupt indicating address match
• Interrupt indicating frame reception, if it passes address filtering and FCS check
• Automatic ACK frame transmission (if the received frame passed the address filter
and FCS check and if an ACK is required by the frame type and ACK request)
• Support of slotted acknowledgment using SLP_TR pin (used for beacon-enabled
operation)
Automatic CSMA-CA and Retransmission (TX_ARET) divides into the tasks:
• CSMA-CA, including automatic CCA retry and random backoff
• Frame transmission and automatic FCS field generation
• Reception of ACK frame (if an ACK was requested)
• Automatic retry of transmissions if ACK was expected but not received or accepted
• Interrupt signaling with transaction status
Automatic FCS check and generation, refer to Section 8.3, is used by the RX_AACK
and TX_ARET modes. In RX_AACK mode, an automatic FCS check is always
performed for incoming frames.
In TX_ARET mode, an ACK which is received within the time required by
IEEE 802.15.4 is automatically accepted if the FCS is valid and the ACK sequence
number must match the sequence number of the previously transmitted frame.
Dependent on the value of the frame pending subfield in the received
acknowledgement frame received, the transaction status is set, see register bits
TRAC_STATUS (register 0x02, TRX_STATE), Section 7.2.7.
An Atmel AT86RF233 state diagram, including the Extended Operating Mode states, is
shown in Figure 7-11. Orange marked states represent the Basic Operating Mode; blue
marked states represent the Extended Operating Mode.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
51
Figure 7-11. Extended Operating Mode State Diagram.
Legend:
Blue: SPI Write to Register TRX_STATE (0x02)
Red: Control signals via IC Pin
Green: Event
Basic Operating Mode States
Extended Operating Mode States
PLL_ON
RX_ON
PLL_ON
TRX_OFF
(Clock State)
XOSC=ON
Pull=OFF
RX_ON
(all states except P_ON)
FORCE_TRX_OFF
(all states except SLEEP or
DEEP_SLEEP)
Frame
End
RX_ON
(Rx Listen State)
BUSY_RX
(Receive State)
TRX_OFF
TRX_OFF
4
5
7
6
8
9
BUSY_RX_AACK BUSY_TX_ARET
SHR
Detected
Trans-
action
Finished
TX_ARET_ON
PLL_ON
SLP_TR=H
or
TX_START
Frame
End
PLL_ON
RX_AACK_ON
TX_ARET_ON
RX_AACK_ON
From / To
TRX_OFF From / To
TRX_OFF
/RST = H
12 13
FORCE_PLL_ON
14
SHR
Detected
TX_ARET_ON
RX_AACK_ON
PLL_ON
(PLL State)
RESET
(from all states)
/RST = L
TRX_OFF
TRX_OFF
2
TRX_OFF
SLP_TR = H
3
P_ON
(Power-on after V
DD
)
XOSC=ON
Pull=ON
SLEEP
(Sleep State)
XOSC=OFF
Pull=OFF
SLP_TR = L
DEEP_SLEEP
(Sleep State)
XOSC=OFF
Pull=ON
RX_AACK_ON
TX_ARET_ON
RX_AACK_ON
RX_ON
TX_ARET_ON
RX_ON
XOSC=ON
Pull=OFF
PREP_
DEEP_SLEEP
(Prepare Sleep State)
TRX_OFF
PREP_DEEP_SLEEP
Frame
End
BUSY_TX
(Transmit State)
TX_START
or
11
10
SLP_TR = H
15 16
17
SLP_TR=H
SLP_TR=L
18
19
(all states except SLEEP or
DEEP_SLEEP or P_ON)
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
52
7.2.1 State Control
The Extended Operating Mode include RX_AACK and TX_ARET modes and are
controlled by writing respective command to register bits TRX_CMD (register 0x02,
TRX_STATE). Receive with Auto matic Acknowledgement state RX_AACK_ON and
Transmit with Automatic Frame Retransmission and CSMA-CA Retry state
TX_ARET_ON can be entered either from TRX_OFF or PLL_ON state as illustrated in
Figure 7-11. The completion of each change state command shall always be confirmed
by reading the register bits TRX_STATUS (register 0x01, TRX_STATUS).
RX_AACK - Receive with Automatic Acknowledgement
A state transition to RX_AACK_ON is initiated by writing the RX_AACK_ON command
to the register bits TRX_CMD. On success, reading register bits TRX_STATUS
(register 0x01, TRX_STATUS) returns RX_AACK_ON or BUSY_RX_AACK. The latter
one is returned when a frame is being received.
The RX_AACK Extended Operating Mode is left by writing a new command to the
register bits TRX_CMD. If the Atmel AT86RF233 is within a frame receive or
acknowledgment procedure (BUSY_RX_AACK), the state change is executed after
finishing. Alternatively, the commands FORCE_TRX_OFF or FORCE_PLL_ON can be
used to cancel the RX_AACK transaction and switch to TRX_OFF or PLL_ON state
respectively.
TX_ARET - Transmit with Automatic Frame Retransmission and CSMA-CA Retry
A state transition to TX_ARET_ON is initiated by writing command TX_ARET_ON to
register bits TRX_CMD (register 0x02, TRX_STATE). The radio transceiver is in the
TX_ARET_ON state when register bits TRX_STATUS (register 0x01, TRX_STATUS)
return TX_ARET_ON. The TX_ARET transaction (frame transmission) is actually
started by a rising edge on pin 11 (SLP_TR) or by writing the command TX_START to
register bits TRX_CMD.
The TX_ARET Extended Operating Mode is left by writing a new command to the
register bits TRX_CMD. If the AT86RF233 is in the mids of a CSMA-CA transaction, a
frame transmission or an acknowledgment procedure (BUSY_TX_ARET), the state
change is executed after completing of the operation. Alternatively, the command
FORCE_TRX_OFF or FORCE_PLL_ON can be used to instantly terminate the
TX_ARET transaction and change into radio transceiver state TRX_OFF or PLL_ON,
respectively.
Note: 1.
A state change request from TRX_OFF to RX_AACK_ON or TX_ARET_ON
internally passes through
PLL_ON state to initiate the radio transceiver front
end. Inserting PLL_ON state and associated delays
while performing this
transition are indicated in Table 7-1. State transitioning can be tracked when
interrupt IRQ_0 (PLL_LOCK) is used as an indicator.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
53
7.2.2 Configuration
As the usage of the Extended Operating Mode is based on Basic Operating Mode
functionality, only features beyond the basic radio transceiver functionality are
described in the following sections. For details of the Basic Operating Mode, refer to
Section 7.1.
When using the RX_AACK or TX_ARET modes, the following registers needs to be
configured.
RX_AACK configuration steps:
• Set the short address, PAN-ID and IEEE address registers 0x20 – 0x2B
• Configure RX_AACK properties registers 0x2C, 0x2E
o Handling of Frame Version Subfield
o Handling of Pending Data Indicator
o Characterization as PAN coordinator
o Handling of Slotted Acknowledgement
• Additional Frame Filtering Properties registers 0x17, 0x2E
o Use of Promiscuous Mode
o Use of automatic ACK generation
o Handling of reserved frame types
The configuration of the Frame Filter is described in Section 8.2.1. The addresses for
the address match algorithm are to be stored in the appropriate address registers.
Additional control of the RX_AACK mode is done with register 0x17 (XAH_CTRL_1)
and register 0x2E (CSMA_SEED_1).
As long as a short address is not set, only broadcast frames and frames matching the
full 64-bit IEEE address can be received.
Configuration examples for different device operating modes and handling of various
frame types can be found in Section 7.2.3.1.
TX_ARET configuration steps:
• Set register bit TX_AUTO_CRC_ON = 1 register 0x04, TRX_CTRL_1
• Configure CSMA-CA
o MAX_FRAME_RETRIES register 0x2C, XAH_CTRL_0
o MAX_CSMA_RETRIES register 0x2C, XAH_CTRL_0
o CSMA_SEED registers 0x2D, 0x2E
o MAX_BE, MIN_BE register 0x2F, CSMA_BE
• Configure CCA (see Section 8.6)
MAX_FRAME_RETRIES (register 0x2C, XAH_CTRL_0) defines the maximum number
of frame retransmissions.
The register bits MAX_CSMA_RETRIES (register 0x2C, XAH_CTRL_0) configure the
number of CSMA-CA retries after a busy channel is detected.
The register bits CSMA_SEED (registers 0x2D, 0x2E) define a random seed for the
backoff-time random-number generator in the Atmel AT86RF233.
The register bits MAX_BE and MIN_BE (register 0x2F, CSMA_BE) set the maximum
and minimum CSMA backoff exponent (see [2]), respectively.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
54
7.2.3 RX_AACK_ON – Receive with Automatic ACK
The RX_AACK Extended Operating Mode handles reception and automatic
acknowledgement of IEEE 802.15.4 compliant frames.
The general functionality of the RX_AACK procedure is shown in Figure 7-12.
The gray shaded area is the standard flow of an RX_AACK transaction for
IEEE 802.15.4 compliant frames, refer to Section 7.2.3.2. All other procedures are
exceptions for specific operating modes or frame formats, refer to Section 7.2.3.3.
In RX_AACK_ON state, the Atmel AT86RF233 listens for incoming frames. After
detecting a valid PHR, the radio transceiver changes into BUSY_RX_AACK state and
parses the frame content of the MAC header (MHR), refer to Section 8.1.2.
If the content of the MAC addressing fields of the received frame (refer to
IEEE 802.15.4 Section 7.2.1) matches one of the configured addresses, dependent on
the addressing mode, an address match interrupt IRQ_5 (AMI) is issued, refer to
Section 8.2. The reference address values are to be stored in registers 0x20 – 0x2B
(Short address, PAN-ID and IEEE address). Frame filtering as described in Section 8.2
is also applied in Basic Operating Mode. However, in Basic Operating Mode, the result
of frame filtering or FCS check do not affect the generation of an interrupt
IRQ_3 (TRX_END).
Generally, at nodes configured as a normal device or a PAN coordinator, a frame is
indicated by interrupt IRQ_3 (TRX_END) if the frame passes the Frame Filter and the
FCS is valid. The interrupt is issued after the completion of the frame reception. The
microcontroller can then read the frame data. An exception applies if promiscuous
mode is enabled, see Section 7.2.3.2. In this case, an interrupt IRQ_3 (TRX_END) is
issued for all frames.
During reception AT86RF233 parses bit[5] (ACK Request) of the frame control field of
the received data or MAC command frame to check if an acknowledgement (ACK) reply
is expected. If the bit is set and if the frame passes the third level of filtering, see
IEEE 802.15.4-2006, Section 7.5.6.2, the radio transceiver automatically generates and
transmits an ACK frame. The sequence number is copied from the received frame.
The content of the frame pending subfield of the ACK response is set by register bit
AACK_SET_PD (register 0x2E, CSMA_SEED_1) when the ACK frame is sent in
response to a data request MAC command frame, otherwise this subfield is set to zero.
By default, the acknowledgment frame is transmitted aTurnaroundTime (12 symbol
periods; see IEEE 802.15.4-2006, Section 6.4.1) after the reception of the last symbol
of a data or MAC command frame. Optionally, for non-compliant networks, this delay
can be reduced to two symbols by register bit AACK_ACK_TIME (register 0x17,
XAH_CTRL_1).
If the register bit AACK_DIS_ACK (register 0x2E, CSMA_SEED_1) is set, no
acknowledgement frame is sent even if an acknowledgment frame is requested. This is
useful for operating the MAC hardware accelerator in promiscuous mode, see
Section 7.2.3.2.
For slotted operation, the start of the transmission of acknowledgement frames is
controlled by pin 11 (SLP_TR), refer to Section 7.2.3.4.
The status of the RX_AACK operation is indicated by register bits TRAC_STATUS
(register 0x02, TRAC_STATUS), see Section 7.2.7.
During the operations described above, the AT86RF233 remains in BUSY_RX_AACK
state.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
55
Figure 7-12. Flow Diagram of RX_AACK.
Reserved Frames
TRX_STATE = RX_AACK_ON
SHR detected
TRX_STATE = BUSY_RX_AACK
Scanning MHR
Frame reception
Frame
Filtering
ACK requested
(see Note 3)
Wait 12 symbol
periods
Transmit ACK
TRX_STATE = RX_AACK_ON
N
Y
N
Y
Generate IRQ_2 (RX_START)
AACK_PROM_MODE
== 1
Generate IRQ_5 (AMI)
Y
Generate IRQ_3 (TRX_END)
Frame reception
Note 3: Additional conditions:
- ACK requested &
- AACK_DIS_ACK==0 &
- frame_version<=AACK_FVN_MODE
Slotted Operation
== 0
Y
AACK_ACK_TIME
== 0
Y
Wait 2 symbol
periods
pin 11 (SLP_TR)
rising edge
N
N
Generate IRQ_3
(TRX_END)
N
Y
N
Wait 2 symbol
periods
FCS valid
(see Note 2)
Y
N
AACK_UPLD_RES_FT
== 1
FCS valid
Generate IRQ_3
(TRX_END)
Y
Y
N
N
N
Note 2: FCS check is omitted for Promiscous Mode
FCF[2:0]
> 3
N
Y
Y
Promiscuous Mode
Note 1: Frame Filtering, Promiscuous Mode and
Reserved Frames:
- A radio transceiver in Promiscuous
Mode, or configured to receive Reserved
Frames handles received frames passing
the third level of filtering
- For details refer to the description of
Promiscuous Mode and Reserved
Frame Types
(see Note 1)
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
56
7.2.3.1 Description of RX_AACK Configuration Bits
Overview
RX_AACK configuration as described below shall be done prior to switching the
AT86RF233 into state RX_AACK_ON, refer to Section 7.2.1.
Table 7-5 summarizes all register bits which affect the behavior of an RX_AACK
transaction. For frame filtering it is further required to setup address registers to match
the expected address.
A graphical representation of various operating modes is illustrated in Figure 7-12.
Table 7-5. Overview of RX_AACK Configuration Bits.
Register
Address
Register
Bits
Register Name Description
0x20,0x21
0x22,0x23
0x24
…
0x2B
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
Setup Frame Filter, see Section 8.2.1.
0x0C 7 RX_SAFE_MODE Dynamic frame buffer protection, see
Section 11.8.
0x17 1 AACK_PROM_MODE Support promiscuous mode.
0x17 2 AACK_ACK_TIME Change auto acknowledge start time.
0x17 4 AACK_UPLD_RES_FT Enable reserved frame type reception,
needed to receive non-standard compliant
frames, see Section 7.2.3.3.
0x17 5 AACK_FLTR_RES_FT Filter reserved frame types like data frame
type, needed for filtering of non-standard
compliant frames, see Section 7.2.3.3.
0x2C 0 SLOTTED_OPERATION If set, acknowledgment transmission has
to be triggered by pin 11 (SLP_TR), see
Section 7.2.3.4.
0x2E 3 AACK_I_AM_COORD If set, the device is a PAN coordinator,
that is responds to a null address, see
Section 7.2.3.2.
0x2E 4 AACK_DIS_ACK Disable generation of acknowledgment.
0x2E 5 AACK_SET_PD Set frame pending subfield in Frame
Control Field (FCF), refer to
Section 8.1.2.2.
0x2E 7:6 AACK_FVN_MODE Controls the ACK behavior, depending on
FCF frame version number.
The usage of the RX_AACK configuration bits for various operating modes of a node is
explained in the following sections. Configuration bits not mentioned in the following two
sections should be set to their reset values according to Table 14-2.
All registers mentioned in Table 7-5 are described in Section 7.2.6.
The general behavior of the “Atmel AT86RF233 Extended Feature Set”, Chapter 11,
settings:
o OQPSK_DATA_RATE (PSDU data rate)
o OQPSK_SCRAM_EN (Scrambler for 2000kb/s data rate)
o SFD_VALUE (alternative SFD value)
o ANT_DIV (Antenna Diversity)
o RX_PDT_LEVEL (blocking frame reception of lower power signals)
o RPC (Reduced Power Consumption)
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
57
are completely independent from RX_AACK mode and can be arbitrarily combined.
7.2.3.2 Configuration of IEEE Compliant Scenarios
Device not operating as a PAN Coordinator
Table 7-6 shows a typical Atmel AT86RF233 RX_AACK configuration of an
IEEE 802.15.4 device operating as a normal device, rather than a PAN coordinator or
router.
Table 7-6. Configuration of IEEE 802.15.4 Devices.
Register
Address
Register
Bits
Register Name Description
0x20,0x21
0x22,0x23
0x24
…
0x2B
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
Setup Frame Filter, see Section 8.2.1.
0x0C 7 RX_SAFE_MODE 0: Disable frame protection.
1: Enable frame protection.
0x2C 0 SLOTTED_OPERATION 0: Slotted acknowledgment transmissions
are not to be used.
1: Slotted acknowledgment transmissions
are to be used, see Section 7.2.3.4.
0x2E 7:6 AACK_FVN_MODE Controls the ACK behavior, depending on
FCF frame version number.
b00: Acknowledges only frames with
version number 0, that is according to
IEEE 802.15.4-2003 frames.
b01: Acknowledges only frames with
version number 0 or 1, that is frames
according to IEEE 802.15.4-2006.
b10: Acknowledges only frames with
version number 0 or 1 or 2.
b11: Acknowledges all frames,
independent of the FCF frame version
number.
Notes: 1. The default value of the short address is 0xFFFF. Thus, if no short address has
been configured, only frames with either the broadcast address or the IEEE
address are accepted by the frame filter.
2. In the IEEE 802.15.4-2003 standard the frame version subfield does not yet
exist but is marked as reserved. According to this standard, reserved fields
have to be set to zero. At the same time, the IEEE 802.15.4-2003 standard
requires ignoring reserved bits upon reception. Thus, there is a contradiction in
the standard which can be interpreted in two ways:
a.
If a network should only allow access to nodes compliant to
IEEE 802.15.4-2003, then AACK_FVN_MODE should be set to zero.
b. If a device should acknowledge all frames independent of its frame version,
AACK_FVN_MODE should be set to three. However, this may result in
conflicts with co-existing IEEE 802.15.4-2006 standard compliant networks.
The same holds for PAN coordinators, see below.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
58
PAN-Coordinator
Table 7-7 shows the Atmel AT86RF233 RX_AACK configuration for a PAN coordinator.
Table 7-7. Configuration of a PAN Coordinator.
Register
Address
Register
Bits
Register Name Description
0x20,0x21
0x22,0x23
0x24
…
0x2B
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
Setup Frame Filter, see Section 8.2.1.
0x0C 7 RX_SAFE_MODE 0: Disable frame protection.
1: Enable frame protection.
0x2C 0 SLOTTED_OPERATION 0: Slotted acknowledgment transmissions
are not to be used.
1: Slotted acknowledgment transmissions
are to be used, see Section 7.2.3.4.
0x2E 3 AACK_I_AM_COORD 1: Device is PAN coordinator.
0x2E 5 AACK_SET_PD 0: Frame pending subfield is not set in
FCF.
1: Frame pending subfield is set in FCF.
0x2E 7:6 AACK_FVN_MODE Controls the ACK behavior, depends on
FCF frame version number.
b00: Acknowledges only frames with
version number 0, that is according to
IEEE 802.15.4-2003 frames.
b01: Acknowledges only frames with
version number 0 or 1, that is frames
according to IEEE 802.15.4-2006.
b10: Acknowledges only frames with
version number 0 or 1 or 2.
b11: Acknowledges all frames,
independent of the FCF frame version
number.
Promiscuous Mode or Sniffer
The promiscuous mode is described in IEEE 802.15.4-2006, Section 7.5.6.5. This mode
is further illustrated in Figure 7-12. According to IEEE 802.15.4-2006 when in
promiscuous mode, the MAC sub layer shall pass received frames with correct FCS to
the next higher layer and shall not process them further. This implies that received
frames should never be automatically acknowledged.
In order to support sniffer application and promiscuous mode, only second level filter
rules as defined by IEEE 802.15.4-2006, Section 7.5.6.2, are applied to the received
frame.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
59
Table 7-8 shows a typical configuration of a device operating in promiscuous mode.
Table 7-8. Configuration of Promiscuous Mode.
Register
Address
Register
Bits
Register Name Description
0x20,0x21
0x22,0x23
0x24
…
0x2B
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
Each address shall be set: 0x00.
0x17 1 AACK_PROM_MODE 1: Enable promiscuous mode.
0x2E 4 AACK_DIS_ACK 1: Disable generation of acknowledgment.
0x2E 7:6 AACK_FVN_MODE Controls the ACK behavior, depends on
FCF frame version number.
b00: Acknowledges only frames with
version number 0, that is according to
IEEE 802.15.4-2003 frames.
b01: Acknowledges only frames with
version number 0 or 1, that is frames
according to IEEE 802.15.4-2006.
b10: Acknowledges only frames with
version number 0 or 1 or 2.
b11: Acknowledges all frames,
independent of the FCF frame version
number.
If the Atmel AT86RF233 radio transceiver is in promiscuous mode, second level of
filtering according to IEEE 802.15.4-2006, Section 7.5.6.2, is applied to a received
frame. However, an IRQ_3 (TRX_END) is issued even if the FCS is invalid. Thus, it is
necessary to read register bit RX_CRC_VALID (register 0x06, PHY_RSSI) after
IRQ_3 (TRX_END) in order to verify the reception of a frame with a valid FCS.
Alternatively, bit[7] of byte RX_STATUS can be evaluated, refer to Section 6.3.2.
If a device, operating in promiscuous mode, receives a frame with a valid FCS which
further passed the third level of filtering according to IEEE 802.15.4-2006,
Section 7.5.6.2, an acknowledgement (ACK) frame would be transmitted. But,
according to the definition of the promiscuous mode, a received frame shall not be
acknowledged, even if requested. Thus, register bit AACK_DIS_ACK (register 0x2E,
CSMA_SEED_1) must be set to one to disable ACK generation.
In all receive modes IRQ_5 (AMI) interrupt is issued, when the received frame matches
the node’s address according to the filter rules described in Section 8.2.
Alternatively, in state RX_ON (Basic Operating Mode, refer to Section 7.1), when a
valid PHR is detected, an IRQ_2 (RX_START) is generated and the frame is received.
The end of the frame reception is signalized with an IRQ_3 (TRX_END). At the same
time the register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is updated with the
result of the FCS check (see Section 8.3). According to the promiscuous mode
definition the register bit RX_CRC_VALID needs to be checked in order to dismiss
corrupted frames.
However, the RX_AACK transaction additionally enables extended functionality like
automatic acknowledgement and non-destructive frame filtering.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
60
7.2.3.3 Configuration of non IEEE 802.15.4 Compliant Scenarios
Sniffer
Table 7-9 shows an Atmel AT86RF233 RX_AACK configuration to setup a sniffer
device. Other RX_AACK configuration bits, refer to Table 7-5, should be set to their
reset values.
All frames received are indicated by an IRQ_2 (RX_START) and IRQ_3 (TRX_END).
After frame reception register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is
updated with the result of the FCS check (see Section 8.3). The RX_CRC_VALID bit
needs to be checked in order to dismiss corrupted frames.
Table 7-9. Configuration of a Sniffer Device.
Register
Address
Register
Bits
Register Name Description
0x17 1 AACK_PROM_MODE 1: Enable promiscuous mode.
0x2E 4 AACK_DIS_ACK 1: Disable generation of acknowledgment.
This operating mode is similar to the promiscuous mode.
Reception of Reserved Frames
In RX_AACK mode, frames with reserved frame types (refer to Table 8-3) can also be
handled. This might be required when implementing proprietary, non-standard
compliant, protocols. The reception of reserved frame types is an extension of the
AT86RF233 Frame Filter, see Section 8.2. Received frames are either handled like
data frames, or may be allowed to completely bypass the Frame Filter. The flow chart in
Figure 7-12 shows the corresponding state machine.
In addition to Table 7-6 or Table 7-7, the following Table 7-10 shows RX_AACK
configuration registers required to setup a node to receive reserved frame types.
Table 7-10. RX_AACK Configuration to Receive Reserved Frame Types.
Register
Address
Register
Bits
Register Name Description
0x17 4 AACK_UPLD_RES_FT 1: Enable reserved frame type reception.
0x17 5 AACK_FLTR_RES_FT Filter reserved frame types like data frame
type, see note below.
0: Disable reserved frame types filtering.
1: Enable reserved frame types filtering.
There are three different options for handling reserved frame types.
1. AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 0:
Any non-corrupted frame with a reserved frame type is indicated by an
IRQ_3 (TRX_END) interrupt. No further address filtering is applied on those frames.
An IRQ_5 (AMI) interrupt is never generated and the acknowledgment subfield is
ignored.
2. AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 1:
If AACK_FLT_RES_FT = 1 any frame with a reserved frame type is filtered by the
address filter similar to a data frame as described in the standard. This implies the
generation of the IRQ_5 (AMI) interrupts upon address match. An
IRQ_3 (TRX_END) interrupt is only generated if the address matched and the
frame was not corrupted. An acknowledgment is only send, when the ACK request
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
61
subfield was set in the received frame and an IRQ_3 (TRX_END) interrupt
occurred.
3. AACK_UPLD_RES_FT = 0:
Any received frame with a reserved frame type is discarded.
Short Acknowledgment Frame (ACK) Start Timing
Register bit AACK_ACK_TIME (register 0x17, XAH_CTRL_1), see Table 7-11 defines
the delay between the end of the frame reception and the start of the transmission of an
acknowledgment frame.
Table 7-11. Overview of RX_AACK Configuration Bits.
Register
Address
Register
Bit
Register Name Description
0x17 2 AACK_ACK_TIME 0: IEEE 802.15.4 standard compliant
acknowledgement timing of 12 symbol
periods. In slotted acknowledgement
operation mode, the acknowledgment
frame transmission can be triggered two
symbol periods after reception of the
frame earliest.
1: Non-standard IEEE 802.15.4 reduced
acknowledgment timing is set to 32µs
(two symbol periods).
This feature can be used in all scenarios, independent of other configurations.
However, shorter acknowledgment timing is especially useful when using High Data
Rate Modes to increase battery lifetime and to improve the overall data throughput;
refer to Section 11.3.
7.2.3.4 RX_AACK Slotted Operation – Slotted Acknowledgement
In networks using slotted operation the start of the acknowledgment frame, and thus the
exact timing, must be provided by the microcontroller. Exact timing requirements for the
transmission of acknowledgments in beacon-enabled networks are explained in
IEEE 802.15.4-2006, Section 7.5.6.4.2. In conjunction with the microcontroller the
Atmel AT86RF233 supports slotted acknowledgement operation. This mode is invoked
by setting register bit SLOTTED_OPERATION (register 0x2C, XAH_CTRL_0) to one.
If an acknowledgment (ACK) frame is to be transmitted in RX_AACK mode, the radio
transceiver expects a rising edge on pin 11 (SLP_TR) to actually start the transmission.
During this waiting period, the transceiver reports SUCCESS_WAIT_FOR_ACK through
register bits TRAC_STATUS (register 0x02, TRX_STATE), see Figure 7-12. The
minimum delay between the occurrence of interrupt IRQ_3 (TRX_END) and pin start of
the ACK frame in slotted operation is two symbol periods.
Figure 7-13 illustrates the timing of an RX_AACK transaction in slotted operation. The
acknowledgement frame is ready to transmit three symbol times after the reception of
the last symbol of a data or MAC command frame indicated by IRQ_3 (TRX_END). The
transmission of the acknowledgement frame is initiated by the microcontroller with the
rising edge of pin 11 (SLP_TR) and starts tTR10 = 16µs later. The interrupt latency tIRQ is
specified in Section 12.4.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
62
Figure 7-13. Timing Example of an RX_AACK Transaction for Slotted Operation.
RX/TX Frame
on Air
RX_AACK_ON
TRX_STATE
Frame Type
RX_AACK_ON
RX/TX RX TX
TRX_END
IRQ
RX
Typ. Processing Delay t
IRQ
5120 704 time [μs]
64 1026
Data Frame (Length = 10, ACK=1) ACK Frame
SFD
32 μs
(2 symbols)
SLP_TR
t
TR10
TX RX
SLP_TR
ACK transmission initated by microcontroller
BUSY_RX_AACK
RX
waiting period signalled by register bits TRAC_STATUS
7.2.3.5 RX_AACK Mode Timing
A timing example of an RX_AACK transaction is shown in Figure 7-14. In this example
a data frame of length 10 with an ACK request is received. The Atmel AT86RF233
changes to state BUSY_RX_AACK after SFD detection. The completion of the frame
reception is indicated by an IRQ_3 (TRX_END) interrupt. The interrupts
IRQ_2 (RX_START) and IRQ_5 (AMI) are disabled in this example. The ACK frame is
automatically transmitted after aTurnaroundTime (12 symbols), assuming default
acknowledgment frame start timing. The interrupt latency tIRQ is specified in
Section 12.4.
Figure 7-14. Timing Example of an RX_AACK Transaction.
RX/TX Frame
on Air
RX_AACK_ON BUSY_RX_AACK
TRX_STATE
Frame Type
RX_AACK_ON
RX/TX RX TX
TRX_END
IRQ
RX
Typ. Processing Delay tIRQ
5120704 time [µs]
64 1088
Data Frame (Length = 10, ACK=1) ACK Frame
SFD
192 µs
(12 symbols)
Note: 1. If register bit AACK_ACK_TIME (register
0x17, XAH_CTRL_1) is set, an
acknowledgment frame is sent already two symbol times after the reception of
the last symbol of a data or MAC command frame.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
63
7.2.4 TX_ARET_ON – Transmit with Automatic Frame Retransmission and CSMA-CA Retry
Figure 7-15. Flow Diagram of TX_ARET.
TRX_STATE = TX_ARET_ON
csma_rctr = 0
TRX_STATE = TX_ARET_ON
N
Y
Failure
Success
N
Y
frame_rctr = 0
Transmit Frame
frame_rctr = frame_rctr + 1
Y
N
N
Y
TRAC_STATUS =
NO_ACK
TRAC_STATUS =
SUCCESS
TRAC_STATUS =
CHANNEL_ACCESS_FAILURE
Issue IRQ_3 (TRX_END) interrupt
CCA
Result
ACK requested
ACK valid
TRAC_STATUS =
SUCCESS_DATA_PENDING
Y
N
Receive ACK
until timeout
Y
N
TRX_STATE = BUSY_TX_ARET
TRAC_STATUS = INVALID
MAX_CSMA_RETRIES
<7
Y
N
csma_rctr >
MAX_CSMA_RETRIES
Y
Note 1: If MAX_CSMA_RETRIES = 7 no retry is
performed
(see Note 1)
Random Back-Off
csma_rctr = csma_rctr + 1
CCA
Start TX
frame_rctr >
MAX_FRAME_RETRIES
Data Pending
N
Overview
The implementation of TX_ARET algorithm is shown in Figure 7-15.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
64
The TX_ARET Extended Operating Mode supports the frame transmission process as
defined by IEEE 802.15.4-2006. It is invoked as described in Section 7.2.1 by writing
TX_ARET_ON to register subfield TRX_CMD (register 0x02, TRX_STATE).
If a transmission is initiated in TX_ARET mode, the Atmel AT86RF233 executes the
CSMA-CA algorithm as defined by IEEE 802.15.4-2006, Section 7.5.1.4. If the CCA
reports IDLE, the frame is transmitted from the Frame Buffer.
If an acknowledgement frame is requested, the radio transceiver checks for an ACK
reply automatically. The CSMA-CA based transmission process is repeated until a valid
acknowledgement is received or the number of frame retransmissions
MAX_FRAME_RETRIES (register 0x2C, XAH_CTRL_0) is exceeded.
The completion of the TX_ARET transaction is indicated by the IRQ_3 (TRX_END)
interrupt, see Section 7.2.5.
Description
Prior to invoking AT86RF233 TX_ARET mode, the basic configuration steps as
described in Section 7.2.2 shall be executed. It is further recommended to write the
PSDU transmit data to the Frame Buffer in advance.
The transmit start event may either come from a rising edge on pin 11 (SLP_TR), refer
to Section 6.6, or by writing a TX_START command to register bits TRX_CMD
(register 0x02, TRX_STATE).
If the CSMA-CA detects a busy channel, it is retried as specified by the register bits
MAX_CSMA_RETRIES (register 0x2C, XAH_CTRL_0). In case that CSMA-CA does
not detect a clear channel after MAX_CSMA_RETRIES, it aborts the TX_ARET
transaction, issues interrupt IRQ_3 (TRX_END), and sets the value of the register bits
TRAC_STATUS to CHANNEL_ACCESS_FAILURE.
During transmission of a frame the radio transceiver parses bit[5] (ACK Request) of the
MAC header (MHR) frame control field of the PSDU data (PSDU octet #1) to be
transmitted to check if an ACK reply is expected.
If no ACK is expected, the radio transceiver issues IRQ_3 (TRX_END) directly after the
frame transmission has been completed. The register bits TRAC_STATUS
(register 0x02, TRX_STATE) are set to SUCCESS.
If an ACK is expected, after transmission the radio transceiver automatically switches to
receive mode waiting for a valid ACK reply (that is matching sequence number and
correct FCS). After receiving a valid ACK frame, the “Frame Pending” subfield of this
frame is parsed and the status register bits TRAC_STATUS are updated to SUCCESS
or SUCCESS_DATA_PENDING accordingly, refer to Table 7-12. At the same time, the
entire TX_ARET transaction is terminated and interrupt IRQ_3 (TRX_END) is issued.
If no valid ACK is received or after timeout of 54 symbol periods (864µs), the radio
transceiver retries the entire transaction (CSMA-CA based frame transmission) until the
maximum number of frame retransmissions is exceeded, see register bits
MAX_FRAME_RETRIES (register 0x2C, XAH_CTRL_0). In that case, the
TRAC_STATUS is set to NO_ACK, the TX_ARET transaction is terminated, and
interrupt IRQ_3 (TRX_END) is issued.
The current CSMA-CA and frame retransmission counter values of an ongoing
TX_ARET transaction can be retrieved by the register bits ARET_FRAME_RETRIES
and ARET_CSMA_RETRIES (register 0x19, XAH_CTRL_2).
Note: 1. The acknowledgment receive procedure does not overwrite the Frame Buffer
content. Transmit data in the Frame Buffer is not modified during the entire
TX_ARET transaction. Received frames, other than the expected ACK frame,
are discarded automatically.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
65
Additionally to the RX Frame Time stamping via pin 10 (DIG2), a TX Frame Time
stamping within TX_ARET mode can be activated, if the register bits IRQ_2_EXT_EN
(register 0x04, TRX_CTRL_1) and ARET_TX_TS_EN (register 0x17, XAH_CTRL_1)
are set to one, see Section 11.6.
After that, the microcontroller may read the value of the register bits TRAC_STATUS
(register 0x02, TRX_STATE) to verify whether the transaction was successful or not.
The register bits are set according to the following cases, additional exit codes are
described in Section 7.2.6.
Table 7-12 summarizes the Extended Operating Mode result codes in register subfield
TRAC_STATUS (register 0x02, TRX_STATE) with respect to the TX_ARET
transaction. Values are meaningful after an interrupt until the next frame transmit.
Table 7-12. Interpretation of TRAC_STATUS Register Bits.
Value Name Description
0 SUCCESS The transaction was responded to by a valid
ACK, or, if no ACK is requested, after a
successful frame transmission.
1 SUCCESS_DATA_PENDING Equivalent to SUCCESS and indicating that the
“Frame Pending” bit (see Section 8.1.2.2) of the
received acknowledgment frame was set.
3 CHANNEL_ACCESS_FAILURE Channel is still busy after attempting
MAX_CSMA_RETRIES of CSMA-CA.
5 NO_ACK No acknowledgement frames were received
during all retry attempts.
7 INVALID Transaction not yet finished.
A value of MAX_CSMA_RETRIES = 7 initiates an immediate TX_ARET transaction
without performing CSMA-CA. This can be used for example to transmit indirect data to
a device. Further the value MAX_FRAME_RETRIES is ignored and the TX_ARET
transaction is performed only once.
A timing example of a TX_ARET transaction is shown in Figure 7-16.
Figure 7-16. Timing Example of a TX_ARET Transaction.
RX/TX Frame
on Air
TX_ARET_ON BUSY_TX_ARET
TRX_STATE
FrameType
TX_ARET_ON
RX/TX RX
TRX_END
IRQ
Typ. Processing Delay t
TR10
6720 x time [µs]
128 x+352
SLP_TR
TX
t
IRQ
Data Frame (Length = 10, ACK=1) ACK Frame
t
CSMA-CA
TXCSMA-CA RX
t
TR11
Notes: 1. tCSMA-CA defines the random CSMA-CA backoff time.
2. Timing figure tTR10 and tTR11 refer to Table 7-1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
66
Here an example data frame of length 10 with an ACK request is transmitted. After that,
the Atmel AT86RF233 switches to receive mode and expects an acknowledgement
response. During the whole transaction including frame transmit, wait for ACK and ACK
receive the radio transceiver status register bits TRX_STATUS (register 0x01,
TRX_STATUS) signals BUSY_TX_ARET.
A successful reception of the acknowledgment frame is indicated by triggering of
IRQ_3 (TRX_END). The status register bits TRX_STATUS (register 0x01,
TRX_STATUS) changes back to TX_ARET_ON state. When the frame pending
subfield of the received ACK frame is set to one (more data is to follow) register bits
TRAC_STATUS (register 0x02, TRX_STATE) are set either to
SUCCESS_DATA_PENDING status instead of SUCCESS status.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
67
7.2.5 Interrupt Handling
The Atmel AT86RF233 interrupt handling in the Extended Operating Mode is similar to
the Basic Operating Mode, refer to Section 7.1.3. Interrupts can be enabled by setting
the appropriate bit in register 0x0E (IRQ_MASK).
For RX_AACK and TX_ARET modes the following interrupts inform about the status of
a frame reception and transmission:
Table 7-13. Interrupt Handling in Extended Operating Mode.
Mode Interrupt Description
RX_AACK IRQ_2 (RX_START) Indicates a PHR reception
IRQ_5 (AMI) Issued at address match
IRQ_3 (TRX_END) Signals completion of RX_AACK transaction if
successful
- A received frame must pass the address filter
-
The FCS is valid
TX_ARET IRQ_3 (TRX_END) Signals completion of TX_ARET transaction
RX_AACK/
TX_ARET
IRQ_0 (PLL_LOCK) Entering RX_AACK_ON or TX_ARET_ON state from
TRX_OFF state, the PLL_LOCK interrupt signals that
the transaction can be started
RX_AACK
For support of the RX_AACK functionality, it is recommended to enable
IRQ_3 (TRX_END). This interrupt is issued only if frames pass the frame filtering, refer
to Section 8.2, and have a valid FCS to reflect data validity. This functionality differs in
Basic Operating Mode, refer to Section 7.1.3. The usage of other interrupts is optional.
On reception of a valid PHR an IRQ_2 (RX_START) is issued. IRQ_5 (AMI) indicates
address match, refer to filter rules in Section 8.2, and the completion of a frame
reception with a valid FCS is indicated by interrupt IRQ_3 (TRX_END).
Thus, it can happen that an IRQ_2 (RX_START) and/or IRQ_5 (AMI) are issued, but
the IRQ_3 (TRX_END) interrupt is never triggered when a frame does not pass the
FCS computation check.
TX_ARET
The IRQ_3 (TRX_END) interrupt is always generated after completing an TX_ARET
transaction. Subsequently the transaction status can be read from register bits
TRAC_STATUS (register 0x02, TRX_STATE).
Several interrupts are automatically suppressed by the radio transceiver during
TX_ARET transaction. In contrast to Section 8.6, the CCA algorithm (part of CSMA-CA)
does not generate interrupt IRQ_4 (CCA_ED_DONE). Furthermore, the interrupts
IRQ_2 (RX_START) and/or IRQ_5 (AMI) are not generated during the TX_ARET
acknowledgment receive process.
All other interrupts as described in Section 6.7, are also available in Extended
Operating Mode.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
68
7.2.6 Register Summary
The following Atmel AT86RF233 registers are to be configured to control the Extended
Operating Mode:
Table 7-14. Register Summary.
Reg.-Addr. Register Name Description
0x01 TRX_STATUS Radio transceiver status, CCA result
0x02 TRX_STATE Radio transceiver state control, TX_ARET status
0x04 TRX_CTRL_1 TX_AUTO_CRC_ON
0x08 PHY_CC_CCA CCA mode control, see Section 8.6.6
0x09 CCA_THRES CCA ED threshold settings, see Section 8.6.6
0x17 XAH_CTRL_1 TX_ARET and RX_AACK control
0x19 XAH_CTRL_2 TX_ARET control
0x20 – 0x2B Frame Filter configuration
- Short address, PAN ID, and IEEE address
-
See Section 8.2.3 and Section 8.2.4
0x2C XAH_CTRL_0 TX_ARET control, retries value control
0x2D CSMA_SEED_0 CSMA-CA seed value
0x2E CSMA_SEED_1 CSMA-CA seed value, RX_AACK control
0x2F CSMA_BE CSMA-CA backoff exponent control
7.2.7 Register Description
Register 0x01 (TRX_STATUS):
The read-only register TRX_STATUS signals the present state of the radio transceiver
as well as the status of a CCA operation.
Figure 7-17. Register TRX_STATUS.
Bit
7
6
5
4
0x01 CCA_DONE CCA_STATUS reserved TRX_STATUS TRX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x01 TRX_STATUS TRX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 4:0 - TRX_STATUS
The register bits TRX_STATUS signal the current radio transceiver status.
Table 7-15. TRX_STATUS.
Register Bits Value Description
TRX_STATUS 0x00 P_ON
0x01 BUSY_RX
0x02 BUSY_TX
0x06 RX_ON
0x08 TRX_OFF (CLK Mode)
0x09 PLL_ON (TX_ON)
0x0F(1) SLEEP
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
69
Register Bits Value Description
0x10 PREP_DEEP_SLEEP
0x11(2) BUSY_RX_AACK
0x12(2) BUSY_TX_ARET
0x16(2) RX_AACK_ON
0x19(2) TX_ARET_ON
0x1F(3) STATE_TRANSITION_IN_PROGRESS
All other values are reserved
Notes: 1. In SLEEP or DEEP_SLEEP state register not accessible.
2. Extended Operating Mode only.
3.
Do not try to initiate a further state change while the radio transceiver is in
STATE_TRANSITION_IN_PROGRESS state.
A read access to TRX_STATUS register signals the current radio transceiver state
status. A state change is initiated by writing a state transition command to register bits
TRX_CMD (register 0x02, TRX_STATE). Alternatively, some state transitions can be
initiated by the rising edge of pin 11 (SLP_TR) in the appropriate state.
Register 0x02 (TRX_STATE):
The radio transceiver states are advanced via register TRX_STATE by writing a
command word into register bits TRX_CMD. The read-only register bits
TRAC_STATUS indicate the status or result of an Extended Operating Mode
transaction.
Figure 7-18. Register TRX_STATE.
Bit
7
6
5
4
0x02 TRAC_STATUS TRX_CMD TRX_STATE
Read/Write
R
R
R
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x02 TRX_CMD TRX_STATE
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
70
• Bit 7:5 – TRAC_STATUS
Table 7-16. TRAC_STATUS.
Register Bits Value Description RX_AACK TX_ARET
TRAC_STATUS 0(1) SUCCESS X X
1 SUCCESS_DATA_PENDING X
2 SUCCESS_WAIT_FOR_ACK X
3 CHANNEL_ACCESS_FAILURE X
5 NO_ACK X
7(1) INVALID X X
All other values are reserved
Note: 1.
Even though the reset value for register bits TRAC_STATUS is zero, the
RX_AACK and TX_ARET procedures set the register bits to TRAC_STATUS =
7 (INVALID) when they are started.
The status of the RX_AACK and TX_ARET procedure is indicated by register bits
TRAC_STATUS. Values are meaningful after an interrupt until the next frame transmit.
Details of the algorithm and a description of the status information are given in
Section 7.2.3 and Section 7.2.4.
RX_AACK
SUCCESS_WAIT_FOR_ACK: Indicates an ACK frame is about to be sent in
RX_AACK slotted acknowledgement. Slotted
acknowledgement operation must be enabled with
register bit SLOTTED_OPERATION (register 0x2C,
XAH_XTRL_0). The microcontroller must pulse
pin 11 (SLP_TR) at the next backoff slot boundary in
order to initiate a transmission of the ACK frame. For
details refer to IEEE 802.15.4-2006, Section 7.5.6.4.2.
TX_ARET
SUCCESS_DATA_PENDING: Indicates a successful reception of an ACK frame with
frame pending bit set to one.
• Bit 4:0 - TRX_CMD
A write access to register bits TRX_CMD initiate a radio transceiver state transition to
the new state.
Table 7-17. TRX_CMD.
Register Bits Value Description
TRX_CMD 0x00(1) NOP
0x02(2) TX_START
0x03 FORCE_TRX_OFF
0x04(3) FORCE_PLL_ON
0x06 RX_ON
0x08 TRX_OFF (CLK Mode)
0x09 PLL_ON (TX_ON)
0x10 PREP_DEEP_SLEEP
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
71
Register Bits Value Description
0x16(4) RX_AACK_ON
0x19(4) TX_ARET_ON
All other values are reserved
Notes: 1. TRX_CMD = “0” after power on reset (POR).
2. The frame transmission starts one symbol after TX_START command.
3.
FORCE_PLL_ON is not valid for states P_ON, SLEEP, DEEP_SLEEP, and
RESET, as well as STATE_TRANSITION_IN_PROGRESS towards these states.
4. Extended Operating Mode only.
A successful state transition shall be confirmed by reading register bits TRX_STATUS
(register 0x01, TRX_STATUS).
The register bits TRX_CMD are used for Basic and Extended Operating Modes, refer to
Section 7.1.
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 7-19. Register TRX_CTRL_1.
Bit 7 6 5 4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 5 - TX_AUTO_CRC_ON
The register bit TX_AUTO_CRC_ON controls the automatic FCS generation for
transmit operations.
Table 7-18. TX_AUTO_CRC_ON.
Register Bits Value Description
TX_AUTO_CRC_ON 0 Automatic FCS generation is disabled
1 Automatic FCS generation is enabled
Note: 1.
The TX_AUTO_CRC_ON function can be used within Basic and Extended
Operating Modes.
For further details refer to Section 8.3.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
72
Register 0x17 (XAH_CTRL_1):
The XAH_CTRL_1 register is a multi-purpose controls register for Extended Operating
Mode.
Figure 7-20. Register XAH_CTRL_1.
Bit 7 6 5 4
0x17 ARET_TX_TS_EN reserved AACK_FLTR_RES_
FT
AACK_UPLD_RES_
FT
XAH_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x17 reserved AACK_ACK_TIME AACK_PROM_
MODE
AACK_SPC_EN XAH_CTRL_1
Read/Write R R/W R/W R/W
Reset value
0 0 0 0
• Bit 7 - ARET_TX_TS_EN
If register bit ARET_TX_TS_EN = 1, then any frame transmission within TX_ARET
mode is signaled via pin 10 (DIG2).
Table 7-19. ARET_TX_TS_EN.
Register Bits Value Description
ARET_TX_TS_EN 0 TX_ARET time stamping via pin 10 (DIG2) is disabled
1(1) TX_ARET time stamping via pin 10 (DIG2) is enabled
Note: 1. It is necessary to set register bit IRQ_2_EXT_EN (register 0x04, TRX_CTRL_1).
• Bit 5 - AACK_FLTR_RES_FT
Filter reserved frame types like data frame type. The register bit AACK_FLTR_RES_FT
shall only be set if register bit AACK_UPLD_RES_FT = 1.
Table 7-20. AACK_FLTR_RES_FT.
Register Bits Value Description
AACK_FLTR_RES_FT 0(1) Filtering reserved frame types is disabled
1(2) Filtering reserved frame types is enabled
Notes: 1.
If AACK_FLTR_RES_FT = 0 the received reserved frame is only checked for a
valid FCS.
2.
If AACK_FLTR_RES_FT = 1 reserved frame types are filtered similar to data
frames as specified in IEEE 802.15.4–2006.
Reserved frame types are explained in IEEE 802.15.4 Section 7.2.1.1.1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
73
• Bit 4 - AACK_UPLD_RES_FT
Upload reserved frame types within RX_AACK mode.
Table 7-21. AACK_UPLD_RES_FT.
Register Bits Value Description
AACK_UPLD_RES_FT 0 Upload of reserved frame types is disabled
1(1) Upload of reserved frame types is enabled
Note: 1.
If AACK_UPLD_RES_FT = 1 received frames indicated as a reserved frame are
further processed. For those frames, an IRQ_3 (TRX_END) interrupt is generated
if the FCS is valid.
In conjunction with the configuration bit AACK_FLTR_RES_FT, these frames are
handled like IEEE 802.15.4 compliant data frames during RX_AACK transaction. An
IRQ_5 (AMI) interrupt is issued, if the addresses in the received frame match the node’s
addresses.
That means, if a reserved frame passes the third level filter rules, an acknowledgement
frame is generated and transmitted if it was requested by the received frame. If this is
not wanted register bit AACK_DIS_ACK (register 0x2E, CSMA_SEED_1) has to be set.
• Bit 2 - AACK_ACK_TIME
The register bit AACK_ACK_TIME controls the acknowledgment frame response time
within RX_AACK mode.
Table 7-22. AACK_ACK_TIME.
Register Bits Value Description
AACK_ACK_TIME 0 Acknowledgment time is 12 symbol periods
(aTurnaroundTime)
1 Acknowledgment time is two symbol periods
According to IEEE 802.15.4-2006, Section 7.5.6.4.2 the transmission of an
acknowledgment frame shall commence 12 symbol periods (aTurnaroundTime) after
the reception of the last symbol of a data or MAC command frame. This is achieved
with the reset value of the register bit AACK_ACK_TIME.
Alternatively, if AACK_ACK_TIME = 1 an acknowledgment frame is sent already two
symbol periods after the reception of the last symbol of a data or MAC command frame.
This may be applied to proprietary networks or networks using the High Data Rate
Modes to increase battery lifetime and to improve the overall data throughput; refer to
Section 11.3.
• Bit 1 - AACK_PROM_MODE
The register bit AACK_PROM_MODE enables the promiscuous mode, within the
RX_AACK mode.
Table 7-23. AACK_PROM_MODE.
Register Bits Value Description
AACK_PROM_MODE 0 Promiscuous mode is disabled
1 Promiscuous mode is enabled
Refer to IEEE 802.15.4-2006 Section 7.5.6.5.
If this register bit is set, every incoming frame with a valid PHR finishes with
IRQ_3 (TRX_END) interrupt even if the third level filter rules do not match or the FCS is
not valid. However, register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is set
accordingly.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
74
In contrast to IEEE 802.15.4-2006, if a frame passes the third level filter rules, an
acknowledgement frame is generated and transmitted unless disabled by register bit
AACK_DIS_ACK (register 0x2E, CSMA_SEED_1), or use Basic Operating Mode
instead.
Register 0x19 (XAH_CTRL_2):
The read-only register XAH_CTRL_2 retrieves the current counter values for Extended
Operating Mode.
Figure 7-21. Register XAH_CTRL_2.
Bit 7 6 5 4
0x19
ARET_FRAME_RETRIES
XAH_CTRL_2
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x19
ARET_CSMA_RETRIES
reserved
XAH_CTRL_2
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:4 - ARET_FRAME_RETRIES
Retrieves current frame retry counter value.
Table 7-24. ARET_FRAME_RETRIES.
Register Bits Value Description
ARET_FRAME_RETRIE
S
0x0 Minimum possible frame retry counter value
0xF Maximum possible frame retry counter value
Note: 1. A new CCA_BACKOFF cycle or new frame transmit cycle changed these value.
• Bit 3:1 - ARET_CSMA_RETRIES
Retrieves current CSMA-CA retry counter value.
Table 7-25. ARET_CSMA_RETRIES.
Register Bits Value Description
ARET_CSMA_RETRIES 0 Minimum possible CSMA-CA retry counter value
5 Maximum possible CSMA-CA retry counter value
Note: 1. A new CCA_BACKOFF cycle or new frame transmit cycle changed these value.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
75
Register 0x2C (XAH_CTRL_0):
The XAH_CTRL_0 register is a control register for Extended Operating Mode.
Figure 7-22. Register XAH_CTRL_0.
Bit 7 6 5 4
0x2C
MAX_FRAME_RETRIES
XAH_CTRL_0
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 1
Bit 3 2 1 0
0x2C MAX_CSMA_RETRIES SLOTTED_
OPERATION
XAH_CTRL_0
Read/Write R/W R/W R/W R/W
Reset value
1 0 0 0
• Bit 7:4 - MAX_FRAME_RETRIES
Number of retransmission attempts in TX_ARET mode before the transaction gets
cancelled.
Table 7-26. MAX_FRAME_RETRIES.
Register Bits Value Description
MAX_FRAME_RETRIES 0x3 The setting of MAX_FRAME_RETRIES in TX_ARET
mode specifies the number of attempts to retransmit a
frame, when it was not acknowledged by the recipient,
before the transaction gets cancelled.
Valid values are [0x7, 0x6, …, 0x0].
• Bit 3:1 - MAX_CSMA_RETRIES
Number of retries in TX_ARET mode to repeat the CSMA-CA procedure before the
transaction gets cancelled.
Table 7-27. MAX_CSMA_RETRIES.
Register Bits Value Description
MAX_CSMA_RETRIES 0(1) No retries
1(1) One retry
2(1) Two retries
3(1) Three retries
4(1) Four retries
5(1) Five retries
7(3) Immediate frame transmission without performing CSMA-
CA
Notes: 1.
MAX_CSMA_RETRIES specifies the number of retries in TX_ARET mode to
repeat the CSMA-
CA procedure before the transaction gets cancelled. According
to IEEE 802.15.4 the valid range of MAX_CSMA_RETRIES is [5, 4, …, 0].
2. MAX_CSMA_RETRIES = 6 is reserved.
3.
A value of MAX_CSMA_RETRIES = 7 initiates an immediate frame transmission
without performing CSMA-
CA. No retry is performed. This may especially be
required for slotted acknowledgement operation.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
76
• Bit 0 - SLOTTED_OPERATION
For RX_AACK mode, the register bit SLOTTED_OPERATION determines, if the
transceiver will require a time base for slotted operation.
Table 7-28. SLOTTED_OPERATION.
Register Bits Value Description
SLOTTED_OPERATION 0 The radio transceiver operates in unslotted mode. An
acknowledgment frame is automatically sent if requested.
1 The transmission of an acknowledgement frame has to be
controlled by the microcontroller.
Using RX_AACK mode in networks operating in beacon or slotted mode, refer to
IEEE 802.15.4-2006, Section 5.5.1, register bit SLOTTED_OPERATION indicates that
acknowledgement frames are to be sent on backoff slot boundaries (slotted
acknowledgement), refer to Section 7.2.3.4.
If this register bit is set the acknowledgement frame transmission has to be initiated by
the microcontroller using the rising edge of pin 11 (SLP_TR). This waiting state is
signaled in register bits TRAC_STATUS (register 0x02, TRX_STATE) with value
SUCCESS_WAIT_FOR_ACK.
Register 0x2D (CSMA_SEED_0):
The register CSMA_SEED_0 contains the lower 8-bit of CSMA_SEED.
Figure 7-23. Register CSMA_SEED_0.
Bit 7 6 5 4
0x2D
CSMA_SEED_0
CSMA_SEED_0
Read/Write R/W R/W R/W R/W
Reset value
1 1 1 0
Bit 3 2 1 0
0x2D
CSMA_SEED_0
CSMA_SEED_0
Read/Write R/W R/W R/W R/W
Reset value
1 0 1 0
• Bit 7:0 - CSMA_SEED_0
Lower 8-bit of CSMA_SEED, bits[7:0]. Used as seed for random number generation in
the CSMA-CA algorithm.
Table 7-29. CSMA_SEED_0.
Register Bits Value Description
CSMA_SEED_0 0xEA This register contains the lower 8-bit of the CSMA_SEED,
bits[7:0]. The higher 3-bit are part of register bits
CSMA_SEED_1 (register 0x2E, CSMA_SEED_1).
CSMA_SEED is the seed for the random number
generation that determines the length of the backoff period
in the CSMA-CA algorithm.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
77
Notes: 1. It is recommended to initialize register bits CSMA_SEED_0 and
CSMA_SEED_1 with random values. This can be done using register bits
RND_VALUE (register 0x06, PHY_RSSI), refer to Section 11.2.
2. The content of register bits CSMA_SEED_0 and CSMA_SEED_1 initializes the
TX_ARET random backoff generator after wakeup from DEEP_SLEEP state. It
is recommended to reinitialize both registers after every DEEP_SLEEP state
with a random value.
Register 0x2E (CSMA_SEED_1):
The CSMA_SEED_1 register is a control register for RX_AACK and contains a part of
the CSMA_SEED for the CSMA-CA algorithm.
Figure 7-24. Register CSMA_SEED_1.
Bit 7 6 5 4
0x2E
AACK_FVN_MODE
AACK_SET_PD
AACK_DIS_ACK
CSMA_SEED_1
Read/Write R/W R/W R/W R/W
Reset value
0 1 0 0
Bit 3 2 1 0
0x2E AACK_I_AM_
COORD
CSMA_SEED_1 CSMA_SEED_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 7:6 - AACK_FVN_MODE
The register bits AACK_FVN_MODE control the ACK behavior dependent on FCF
frame version number within RX_AACK mode.
Table 7-30. AACK_FVN_MODE.
Register Bits Value Description
AACK_FVN_MODE 0 Accept frames with version number 0
1 Accept frames with version number 0 or 1
2 Accept frames with version number 0 or 1 or 2
3 Accept frames independent of frame version number
Note: 1. AACK_FVN_MODE value one indicates frames according to IEEE 802.15.4–2006,
a value of three indicates frames according to IEEE 802.15.4–2003 standard.
The frame control field of the MAC header (MHR) contains a frame version subfield.
The setting of register bits AACK_FVN_MODE specifies the frame filtering behavior of
the Atmel AT86RF233. According to the content of these register bits the radio
transceiver passes frames with a specific frame version number, number group, or
independent of the frame version number.
Thus the register bits AACK_FVN_MODE defines the maximum acceptable frame
version. Received frames with a higher frame version number than configured do not
pass the frame filter and are not acknowledged.
The frame version field of the acknowledgment frame is set to zero according to
IEEE 802.15.4-2006, Section 7.2.2.3.1 Acknowledgment frame MHR fields.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
78
• Bit 5 - AACK_SET_PD
The content of AACK_SET_PD bit is copied into the frame pending subfield of the
acknowledgment frame if the ACK is the response to a data request MAC command
frame.
Table 7-31. AACK_SET_PD.
Register Bits Value Description
AACK_SET_PD 0 Pending data bit set to zero
1 Pending data bit set to one
In addition, if register bits AACK_FVN_MODE (register 0x2E, CSMA_SEED_1) are
configured to accept frames with a frame version other than zero or one, the content of
register bit AACK_SET_PD is also copied into the frame pending subfield of the
acknowledgment frame for any MAC command frame with a frame version of two or
three that have the security enabled subfield set to one. This is done with the
assumption that a future version of the IEEE 802.15.4-2006 [2] standard might change
the length or structure of the auxiliary security header.
• Bit 4 - AACK_DIS_ACK
If this bit is set no acknowledgment frames are transmitted in RX_AACK Extended
Operating Mode, even if requested.
Table 7-32. AACK_DIS_ACK.
Register Bits Value Description
AACK_DIS_ACK 0 Acknowledgment frames are transmitted
1 Acknowledgment frames are not transmitted
• Bit 3 - AACK_I_AM_COORD
This register bit has to be set if the node is a PAN coordinator. It is used for frame
filtering in RX_AACK.
Table 7-33. AACK_I_AM_COORD.
Register Bits Value Description
AACK_I_AM_COORD 0 PAN coordinator addressing is disabled
1 PAN coordinator addressing is enabled
If AACK_I_AM_COORD = 1 and if only source addressing fields are included in a data
or MAC command frame, the frame shall be accepted only if the device is the PAN
coordinator and the source PAN identifier matches macPANId, for details refer to
IEEE 802.15.4-2006, Section 7.5.6.2 (third-level filter rule six).
• Bit 2:0 - CSMA_SEED_1
Higher 3-bit of CSMA_SEED, bits[10:8]. Seed for random number generation in the
CSMA-CA algorithm.
Table 7-34. CSMA_SEED_1.
Register Bits Value Description
CSMA_SEED_1 2 These register bits are the higher 3-bit of the
CSMA_SEED, bits [10:8]. The lower part is in register
0x2D (CSMA_SEED_0), see register CSMA_SEED_0 for
details.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
79
Register 0x2F (CSMA_BE):
The register CSMA_BE contains the backoff exponents for the CSMA-CA algorithm.
Figure 7-25. Register CSMA_BE.
Bit
7
6
5
4
0x2F MAX_BE CSMA_BE
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
1
0
1
Bit
3
2
1
0
0x2F MIN_BE CSMA_BE
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
1
1
Note: 1. If MIN_BE = 0 and MAX_BE = 0 the CCA backoff period is always set to zero.
• Bit 7:4 - MAX_BE
Maximum backoff exponent in the CSMA-CA algorithm.
Table 7-35. MAX_BE.
Register Bits Value Description
MAX_BE 0x5 Register bits MAX_BE defines the maximum backoff
exponent used in the CSMA-CA algorithm to generate a
pseudo random number for CCA backoff.
Valid values are [0x8, 0x7, …, 0x0].
For details refer to IEEE 802.15.4-2006, Section 7.5.1.4.
• Bit 3:0 - MIN_BE
Minimum backoff exponent in the CSMA-CA algorithm.
Table 7-36. MIN_BE.
Register Bits Value Description
MIN_BE 0x3 Register bits MIN_BE defines the minimum backoff
exponent used in the CSMA-CA algorithm to generate a
pseudo random number for CCA backoff.
Valid values are [MAX_BE, (MAX_BE – 1), …, 0x0].
For details refer to IEEE 802.15.4-2006, Section 7.5.1.4.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
80
8 Functional Description
8.1 Introduction – IEEE 802.15.4-2006 Frame Format
Figure 8-1 provides an overview of the physical layer (PHY) frame structure as defined
by the IEEE 802.15.4-2006 standard. Figure 8-2 shows the medium access control
layer (MAC) frame structure.
Figure 8-1. IEEE 802.15.4 Frame Format - PHY-Layer Frame Structure (PPDU).
Maximum 127 octets
PHY Service Data Unit (PSDU)
1 octet
(PHR)
5 octets
Synchronization Header (SHR)
PHY Protocol Data Unit (PPDU)
Preamble Sequence SFD Frame Length PHY Payload
MAC Protocol Data Unit (MPDU)
8.1.1 PHY Protocol Data Unit (PPDU)
8.1.1.1 Synchronization Header (SHR)
The SHR consists of a four-octet preamble field (all zero), followed by a single byte
start-of-frame delimiter (SFD) which has the predefined value 0xA7. During
transmission, the SHR is automatically generated by the Atmel AT86RF233, thus the
Frame Buffer shall contain PHR and PSDU only, see Section 6.3.2.
The transmission of the SHR requires 160µs (10 symbols). As the SPI data rate is
normally higher than the over-air data rate, this allows the microcontroller to initiate a
transmission without having transferred the full frame data already. Instead it is possible
to subsequently write the frame content.
The fact that the SPI data rate is normally higher than over-the-air data rate, allows the
microcontroller to first initiate a frame transmission and then as the SHR is transmitted
write the frame data. This is to minimize frame buffer data fill overhead transmission
delay.
During a frame reception, the SHR is used for synchronization purposes. The matching
SFD determines the beginning of the PHR and the following PSDU payload data.
8.1.1.2 PHY Header (PHR)
The PHY header is a single octet following the SHR. The least significant seven bits
denote the frame length of the following PSDU, while the most significant bit of that
octet is reserved, and shall be set to zero for IEEE 802.15.4 compliant frames.
On reception, the PHR is returned as the first octet during Frame Buffer read access.
While the IEEE 802.15.4-2006 standard declares bit seven of the PHR octet as being
reserved, the AT86RF233 preserves this bit upon transmission and reception so it can
be used to carry additional information within proprietary networks. Nevertheless, this
bit is not considered to be a part of the frame length, so only frames between one and
127 octets are possible. For IEEE 802.15.4 compliant operation bit[7] has to be masked
by software.
In transmit mode, the PHR needs to be supplied as the first octet during Frame Buffer
write access, see Section 6.3.2.
In receive mode, the PHR (that is frame length greater than zero) is returned as the first
octet during Frame Buffer read access (see Section 6.3.2) and is signaled by an
interrupt IRQ_2 (RX_START).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
81
8.1.1.3 PHY Payload (PHY Service Data Unit, PSDU)
The PSDU has a variable length between zero and aMaxPHYPacketSize (127,
maximum PSDU size in octets). The length of the PSDU is signaled by the frame length
field (PHR), refer to Table 8-1. The PSDU contains the MAC protocol data unit (MPDU),
where the last two octets are used for the Frame Check Sequence (FCS), see
Section 8.3.
Received frames with a frame length field set to zero (invalid PHR) are not signaled to
the microcontroller.
Table 8-1 summarizes the type of payload versus the frame length value.
Table 8-1. Frame Length Field – PHR.
Frame Length Value Payload
0 - 4 Reserved
5 MPDU (Acknowledgement)
6 – 8 Reserved
9 - aMaxPHYPacketSize MPDU
8.1.1.4 Timing Summary
Table 8-2 shows timing information for the above mentioned frame structure depending
on the selected data rate.
Table 8-2. PPDU Timing.
PHY Mode PSDU
Bit Rate
[kb/s]
Header
Bit Rate
[kb/s]
Duration
SHR [µs] PHR [µs] Max. PSDU [ms]
O-QPSK (1) 250 250 160 32 4.064
O-QPSK (2) 500 250 160 32 2.032
1000 250 160 32 1.016
2000 250 160 32 0.508
Notes: 1. Compliant to IEEE 802.15.4-2006 [2].
2. High Data Rate Modes, see Section 11.3.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
82
8.1.2 MAC Protocol Data Unit (MPDU)
Figure 8-2 shows the frame structure of the MAC layer.
Figure 8-2. IEEE 802.15.4-2006 Frame Format - MAC-Layer Frame Structure (MPDU).
Frame Control Field 2 octets
Frame
Pending Reserved Frame Version
ACK
Request
PAN ID
Comp.
Destination
addressing mode
Source
addressing mode
Sec.
Enabled
(MFR)
MAC Service Data Unit (MSDU)
MAC Protocol Data Unit (MPDU)
MAC Payload FCS
Frame Type
012345678910 11 12 13 14 15
MAC Header (MHR)
FCF Addressing Fields
Sequence
Number
2 octets
CRC-16
0/5/6/10/14 octets
Auxiliary Security Header
0/4/6/8/10/12/14/16/18/20 octets
Destination
PAN ID
Destination
address
Source
PAN ID
Source
address
8.1.2.1 MAC Header (MHR) Fields
The MAC header consists of the Frame Control Field (FCF), a sequence number, and
the addressing fields (which are of variable length, and can even be empty in certain
situations).
8.1.2.2 Frame Control Field (FCF)
The FCF consists of 16 bits, and occupies the first two octets of the MPDU or PSDU,
respectively.
Figure 8-3. IEEE 802.15.4-2006 Frame Control Field (FCF).
Frame Control Field 2 octets
Frame
Pending Reserved Frame Version
ACK
Request
PAN ID
Comp.
Destination
addressing mode
Source
addressing mode
Sec.
Enabled
Frame Type
0123456 7 8 9 10 11 12 13 14 15
Bits [2:0]: describes the “Frame Type“. Table 8-3 summarizes frame types defined by
IEEE 802.15.4-2006 [2], Section 7.2.1.1.1.
Table 8-3. Frame Control Field – Frame Type Subfield.
Frame Control Field Bit Assignments Description
Frame Type Value
b2 b1 b0
Value
000 0 Beacon
001 1 Data
010 2 Acknowledge
011 3 MAC command
100 – 111 4 – 7 Reserved
This subfield is used for frame filtering by the third level filter rules. By default, only
frame types 0 – 3 pass the third level filter rules, refer to Section 8.2. Automatic frame
filtering by the Atmel AT86RF233 is enabled when using the RX_AACK mode, refer to
Section 7.2.3.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
83
However, a reserved frame (frame type value > 3) can be received if register bit
AACK_UPLD_RES_FT (register 0x17, XAH_CTRL_1) is set, for details refer to
Section 7.2.3.3.
Frame filtering is also provided in Basic Operating Mode, refer to Section 7.1.
Bit 3: indicates whether security processing applies to this frame. This field is evaluated
by the Frame Filter.
Bit 4: is the “Frame Pending” subfield. This field can be set in an acknowledgment
frame (ACK) in response to a data request MAC command frame. This bit indicates that
the node, which transmitted the ACK, might have more data to send to the node
receiving the ACK.
Note: 1. For acknowledgment frames automatically generated by the AT86RF233, this
bit is set according to the content of register bit AACK_SET_PD in register 0x2E
(CSMA_SEED_1) if the received frame was a data request MAC command
frame.
Bit 5: forms the “Acknowledgment Request” subfield. If this bit is set within a data or
MAC command frame that is not broadcast, the recipient shall acknowledge the
reception of the frame within the time specified by IEEE 802.15.4 (that is within 192µs
for non beacon-enabled networks).
The radio transceiver parses this bit during RX_AACK mode and transmits an
acknowledgment frame if necessary.
In TX_ARET mode this bit indicates if an acknowledgement frame is expected after
transmitting a frame. If this is the case, the receiver waits for the acknowledgment
frame, otherwise the TX_ARET transaction is finished.
Bit 6: the “PAN ID Compression” subfield, indicates that in a frame where both the
destination and source addresses are present, the PAN ID is omitted from the source
addressing field. This bit is evaluated by the Frame Filter of the Atmel AT86RF233. This
subfield was previously named “Intra-PAN”.
Bits [11:10]: the “Destination Addressing Mode” subfield describes the format of the
destination address of the frame. The values of the address modes are summarized in
Table 8-4, according to IEEE 802.15.4.
Table 8-4. Frame Control Field – Destination and Source Addressing Mode.
Frame Control Field Bit Assignments Description
Addressing Mode
b11 b10
b15 b14
Value
00 0 PAN identifier and address fields are not present
01 1 Reserved
10 2 Address field contains a 16-bit short address
11 3 Address field contains a 64-bit extended address
If the destination address mode is either two or three (that is if the destination address
is present), it always consists of a 16-bit PAN-ID first, followed by either the 16-bit or
64-bit address as described by the mode.
Bits [13:12]: the “Frame Version” subfield specifies the version number corresponding
to the frame, see Table 8-5. These bits are reserved in IEEE 802.15.4-2003.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
84
This subfield shall be set to zero to indicate a frame compatible with
IEEE 802.15.4-2003 and one to indicate an IEEE 802.15.4-2006 frame. All other
subfield values shall be reserved for future use.
RX_AACK register bits AACK_FVN_MODE (register 0x2E, CSMA_SEED_1) controls
the behavior of frame acknowledgements. This register determines if, depending on the
Frame Version Number, a frame is acknowledged or not. This is necessary for
backward compatibility to IEEE 802.15.4-2003 and for future use. Even if frame version
numbers two and three are reserved, it can be handled by the radio transceiver, for
details refer to Section 7.2.7.
See IEEE 802.15.4-2006 [2], Section 7.2.3, for details on frame compatibility.
Table 8-5. Frame Control Field – Frame Version Subfield.
Frame Control Field Bit Assignments Description
Frame Version
b13 b12
Value
00 0 Frames are compatible with IEEE 802.15.4-2003
01 1 Frames are compatible with IEEE 802.15.4-2006
10 2 Reserved
11 3 Reserved
Bits [15:14]: the “Source Addressing Mode” subfield, with similar meaning as
“Destination Addressing Mode”, see Table 8-4.
The addressing field description bits of the FCF (Bits 0–2, 3, 6, 10–15) affect the
Atmel AT86RF233 Frame Filter, see Section 8.2.
8.1.2.3 Frame Compatibility between IEEE 802.15.4-2003 and IEEE 802.15.4-2006
All unsecured frames according to IEEE 802.15.4-2006 are compatible with unsecured
frames compliant with IEEE 802.15.4-2003 with two exceptions: a coordinator
realignment command frame with the “Channel Page” field present (see
IEEE 802.15.4-2006 [2], Section 7.3.8) and any frame with a MAC Payload field larger
than aMaxMACSafePayloadSize octets.
Compatibility for secured frames is shown in Table 8-6, which identifies the security
operating modes for IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
85
Table 8-6. Frame Control Field – Security and Frame Version.
Frame Control Field Bit Assignments Description
Security Enabled
b3
Frame Version
b13 b12
0 00 No security. Frames are compatible between
IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
0 01 No security. Frames are not compatible between
IEEE 802.15.4-2003 and IEEE 802.15.4-2006.
1 00 Secured frame formatted according to
IEEE 802.15.4-2003. This frame type is not
supported in IEEE 802.15.4-2006.
1 01 Secured frame formatted according to
IEEE 802.15.4-2006.
8.1.2.4 Sequence Number
The one-octet sequence number following the FCF identifies a particular frame, so that
duplicated frame transmissions can be detected. While operating in RX_AACK mode,
the content of this field is copied from the frame to be acknowledged into the
acknowledgment frame.
8.1.2.5 Addressing Fields
The addressing fields of the MPDU are used by the Atmel AT86RF233 for address
matching indication. The destination address (if present) is always first, followed by the
source address (if present). Each address field consists of the PAN-ID and a device
address. If both addresses are present, and the “PAN ID compression” subfield in the
FCF is set to one, the source PAN-ID is omitted.
Note that in addition to these general rules, IEEE 802.15.4 further restricts the valid
address combinations for the individual possible MAC frame types. For example, the
situation where both addresses are omitted (source addressing mode = 0 and
destination addressing mode = 0) is only allowed for acknowledgment frames. The
address filter in the AT86RF233 has been designed to apply to IEEE 802.15.4
compliant frames. It can be configured to handle other frame formats and exceptions.
8.1.2.6 Auxiliary Security Header Field
The Auxiliary Security Header specifies information required for security processing and
has a variable length. This field determines how the frame is actually protected (security
level) and which keying material from the MAC security PIB is used (see
IEEE 802.15.4-2006 [2], Section 7.6.1). This field shall be present only if the Security
Enabled subfield b3, see Section 8.1.2.3, is set to one. For details of its structure, see
IEEE 802.15.4-2006, Section 7.6.2 Auxiliary security header.
8.1.2.7 MAC Service Data Unit (MSDU)
This is the actual MAC payload. It is usually structured according to the individual frame
type. A description can be found in IEEE 802.15.4-2006, Section 5.5.3.2.
8.1.2.8 MAC Footer (MFR) Fields
The MAC footer consists of a two octet Frame Checksum (FCS), for details refer to
Section 8.3.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
86
8.2 Frame Filter
Frame Filtering is a procedure that evaluates whether or not a received frame matches
predefined criteria, like source or destination address or frame types. A filtering
procedure as described in IEEE 802.15.4-2006 Section 7.5.6.2 (Third level of filtering)
is applied to the frame to accept a received frame and to generate the address match
interrupt IRQ_5 (AMI).
The Atmel AT86RF233 Frame Filter passes only frames that satisfy all of the following
requirements/rules (quote from IEEE 802.15.4-2006, Section 7.5.6.2):
1. The Frame Type subfield shall not contain a reserved frame type.
2. The Frame Version subfield shall not contain a reserved value.
3. If a destination PAN identifier is included in the frame, it shall match macPANId or
shall be the broadcast PAN identifier (0xFFFF).
4. If a short destination address is included in the frame, it shall match either
macShortAddress or the broadcast address (0xFFFF). Otherwise, if an extended
destination address is included in the frame, it shall match aExtendedAddress.
5. If the frame type indicates that the frame is a beacon frame, the source PAN
identifier shall match macPANId unless macPANId is equal to 0xFFFF, in which case
the beacon frame shall be accepted regardless of the source PAN identifier.
6. If only source addressing fields are included in a data or MAC command frame, the
frame shall be accepted only if the device is the PAN coordinator and the source
PAN identifier matches macPANId.
Moreover the AT86RF233 has two additional requirements:
7. The frame type shall indicate that the frame is not an acknowledgment (ACK) frame.
8. At least one address field must be present.
Address match, indicated by interrupt IRQ_5 (AMI), is further controlled by the content
of subfields of the frame control field of a received frame according to the following rule:
If Destination Addressing Mode is 0/1 and Source Addressing Mode is zero (see
Section 8.1.2.2), no interrupt IRQ_5 (AMI) is generated. This effectively causes all
acknowledgement frames not to be announced, which would otherwise always pass the
filter, regardless of whether they are intended for this device or not.
For backward compatibility to IEEE 802.15.4-2003 third level filter rule two (Frame
Version) can be disabled by register bits AACK_FVN_MODE (register 0x2E,
CSMA_SEED_1).
Frame filtering is available in Extended and Basic Operating Mode. A frame that passes
the Frame Filter generates the interrupt IRQ_5 (AMI) if not masked.
Notes: 1. Filter rule one
is affected by register bits AACK_FLTR_RES_FT and
AACK_UPLD_RES_FT, Section 7.2.7.
2. Filter rule two is affected by register bits AACK_FVN_MODE, Section 7.2.7.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
87
8.2.1 Configuration
The Frame Filter is configured by setting the appropriate address variables and several
additional properties as described in Table 8-7.
Table 8-7. Frame Filter Configuration.
Register
Address
Register
Bits
Register Name Description
0x20,0x21
0x22,0x23
0x24
…
0x2B
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
Set macShortAddress, macPANId , and
aExtendedAddress as described in [2].
0x17 1 AACK_PROM_MODE 0: Disable promiscuous mode.
1: Enable promiscuous mode.
0x17 4 AACK_UPLD_RES_FT Enable reserved frame type reception,
needed to receive non-standard compliant
frames, see Section 8.2.2.
0: Disable reserved frame type reception.
1: Enable reserved frame type reception.
0x17 5 AACK_FLTR_RES_FT Filter reserved frame types like data frame
type, needed for filtering of non-standard
compliant frames.
0: Disable reserved frame types filtering.
1: Enable reserved frame types filtering.
0x2E 3 AACK_I_AM_COORD 0: Device is not PAN coordinator.
1: Device is PAN coordinator.
0x2E 7:6 AACK_FVN_MODE Controls the ACK behavior, depends on
FCF frame version number.
b00: Acknowledges only frames with
version number 0, that is according to
IEEE 802.15.4-2003 frames.
b01: Acknowledges only frames with
version number 0 or 1, that is frames
according to IEEE 802.15.4-2006.
b10: Acknowledges only frames with
version number 0 or 1 or 2.
b11: Acknowledges all frames,
independent of the FCF frame version
number.
8.2.2 Handling of Reserved Frame Types
Reserved frame types (as described in Section 7.2.3.3) are treated according to bits
AACK_UPLD_RES_FT and AACK_FLTR_RES_FT of register 0x17 (XAH_CTRL_1)
with three options:
1. AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 0:
Any non-corrupted frame with a reserved frame type is indicated by an
IRQ_3 (TRX_END) interrupt. No further address filtering is applied on those frames.
An IRQ_5 (AMI) interrupt is never generated and the acknowledgment subfield is
ignored.
2. AACK_UPLD_RES_FT = 1, AACK_FLT_RES_FT = 1:
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
88
If AACK_FLT_RES_FT = 1 any frame with a reserved frame type is filtered by the
address filter similar to a data frame as described in the standard. This implies the
generation of the IRQ_5 (AMI) interrupts upon address match. An
IRQ_3 (TRX_END) interrupt is only generated if the address matched and the
frame was not corrupted. An acknowledgment is only send, when the ACK request
subfield was set in the received frame and an IRQ_3 (TRX_END) interrupt
occurred.
3. AACK_UPLD_RES_FT = 0:
Any received frame with a reserved frame type is discarded.
8.2.3 Register Description
Register 0x17 (XAH_CTRL_1):
The XAH_CTRL_1 register is a multi-purpose controls register for Extended Operating
Mode.
Figure 8-4. Register XAH_CTRL_1.
Bit
7
6
5
4
0x17 ARET_TX_TS_EN reserved AACK_FLTR_RES_
FT
AACK_UPLD_RES_
FT XAH_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x17 reserved AACK_ACK_TIME AACK_PROM_
MODE AACK_SPC_EN XAH_CTRL_1
Read/Write
R
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 5 - AACK_FLTR_RES_FT
Filter reserved frame types like data frame type. The register bit AACK_FLTR_RES_FT
shall only be set if register bit AACK_UPLD_RES_FT = 1.
Table 8-8. AACK_FLTR_RES_FT.
Register Bits Value Description
AACK_FLTR_RES_FT 0(1) Filtering reserved frame types is disabled
1(2) Filtering reserved frame types is enabled
Notes: 1.
If AACK_FLTR_RES_FT = 0 the received reserved frame is only checked for a
valid FCS.
2.
If AACK_FLTR_RES_FT = 1 reserved frame types are filtered similar to data
frames as specified in IEEE 802.15.4–2006.
Reserved frame types are explained in IEEE 802.15.4 Section 7.2.1.1.1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
89
• Bit 4 - AACK_UPLD_RES_FT
Upload reserved frame types within RX_AACK mode.
Table 8-9. AACK_UPLD_RES_FT.
Register Bits Value Description
AACK_UPLD_RES_FT 0 Upload of reserved frame types is disabled
1(1) Upload of reserved frame types is enabled
Note: 1.
If AACK_UPLD_RES_FT = 1 received frames indicated as a reserved frame are
further processed. For those frames, an IRQ_3 (TRX_END) interrupt is generated
if the FCS is valid.
In conjunction with the configuration bit AACK_FLTR_RES_FT, these frames are
handled like IEEE 802.15.4 compliant data frames during RX_AACK transaction. An
IRQ_5 (AMI) interrupt is issued, if the addresses in the received frame match the node’s
addresses.
That means, if a reserved frame passes the third level filter rules, an acknowledgement
frame is generated and transmitted if it was requested by the received frame. If this is
not wanted register bit AACK_DIS_ACK (register 0x2E, CSMA_SEED_1) has to be set.
• Bit 1 - AACK_PROM_MODE
The register bit AACK_PROM_MODE enables the promiscuous mode, within the
RX_AACK mode.
Table 8-10. AACK_PROM_MODE.
Register Bits Value Description
AACK_PROM_MODE 0 Promiscuous mode is disabled
1 Promiscuous mode is enabled
Refer to IEEE 802.15.4-2006 Section 7.5.6.5.
If this register bit is set, every incoming frame with a valid PHR finishes with
IRQ_3 (TRX_END) interrupt even if the third level filter rules do not match or the FCS is
not valid. However, register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is set
accordingly.
In contrast to IEEE 802.15.4-2006, if a frame passes the third level filter rules, an
acknowledgement frame is generated and transmitted unless disabled by register bit
AACK_DIS_ACK (register 0x2E, CSMA_SEED_1), or use Basic Operating Mode
instead.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
90
Register 0x2E (CSMA_SEED_1):
The CSMA_SEED_1 register is a control register for RX_AACK and contains a part of
the CSMA_SEED for the CSMA-CA algorithm.
Figure 8-5. Register CSMA_SEED_1.
Bit 7 6 5 4
0x2E
AACK_FVN_MODE
AACK_SET_PD
AACK_DIS_ACK
CSMA_SEED_1
Read/Write R/W R/W R/W R/W
Reset value
0 1 0 0
Bit 3 2 1 0
0x2E AACK_I_AM_
COORD
CSMA_SEED_1 CSMA_SEED_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 7:6 - AACK_FVN_MODE
The register bits AACK_FVN_MODE control the ACK behavior dependent on FCF
frame version number within RX_AACK mode.
Table 8-11. AACK_FVN_MODE.
Register Bits Value Description
AACK_FVN_MODE 0 Accept frames with version number 0
1 Accept frames with version number 0 or 1
2 Accept frames with version number 0 or 1 or 2
3 Accept frames independent of frame version number
Note: 1. AACK_FVN_MODE value one indicates frames according to IEEE 802.15.4–2006,
a value of three indicates frames according to IEEE 802.15.4–2003 standard.
The frame control field of the MAC header (MHR) contains a frame version subfield.
The setting of register bits AACK_FVN_MODE specifies the frame filtering behavior of
the Atmel AT86RF233. According to the content of these register bits the radio
transceiver passes frames with a specific frame version number, number group, or
independent of the frame version number.
Thus the register bits AACK_FVN_MODE defines the maximum acceptable frame
version. Received frames with a higher frame version number than configured do not
pass the frame filter and are not acknowledged.
The frame version field of the acknowledgment frame is set to zero according to
IEEE 802.15.4-2006, Section 7.2.2.3.1 Acknowledgment frame MHR fields.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
91
• Bit 3 - AACK_I_AM_COORD
This register bit has to be set if the node is a PAN coordinator. It is used for frame
filtering in RX_AACK.
Table 8-12. AACK_I_AM_COORD.
Register Bits Value Description
AACK_I_AM_COORD 0 PAN coordinator addressing is disabled
1 PAN coordinator addressing is enabled
If AACK_I_AM_COORD = 1 and if only source addressing fields are included in a data
or MAC command frame, the frame shall be accepted only if the device is the PAN
coordinator and the source PAN identifier matches macPANId, for details refer to
IEEE 802.15.4-2006, Section 7.5.6.2 (third-level filter rule six).
8.2.4 Register Description – Address Registers
Register 0x20 (SHORT_ADDR_0):
This register contains the lower 8-bit of the MAC short address for Frame Filter address
recognition, bits[7:0].
Figure 8-6. Register SHORT_ADDR_0.
Bit
7
6
5
4
0x20 SHORT_ADDR_0 SHORT_ADDR_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
1
1
Bit
3
2
1
0
0x20 SHORT_ADDR_0 SHORT_ADDR_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
1
1
Register 0x21 (SHORT_ADDR_1):
This register contains the higher 8-bit of the MAC short address for Frame Filter
address recognition, bits[15:8].
Figure 8-7. Register SHORT_ADDR_1.
Bit 7 6 5 4
0x21
SHORT_ADDR_1
SHORT_ADDR_1
Read/Write R/W R/W R/W R/W
Reset value
1 1 1 1
Bit 3 2 1 0
0x21
SHORT_ADDR_1
SHORT_ADDR_1
Read/Write R/W R/W R/W R/W
Reset value
1 1 1 1
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
92
Register 0x22 (PAN_ID_0):
This register contains the lower 8-bit of the MAC PAN ID for Frame Filter address
recognition, bits[7:0].
Figure 8-8. Register PAN_ID_0.
Bit
7
6
5
4
0x22 PAN_ID_0 PAN_ID_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
1
1
Bit
3
2
1
0
0x22 PAN_ID_0 PAN_ID_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
1
1
Register 0x23 (PAN_ID_1):
This register contains the higher 8-bit of the MAC PAN ID for Frame Filter address
recognition, bits[15:8].
Figure 8-9. Register PAN_ID_1.
Bit 7 6 5 4
0x23
PAN_ID_1
PAN_ID_1
Read/Write R/W R/W R/W R/W
Reset value
1 1 1 1
Bit 3 2 1 0
0x23
PAN_ID_1
PAN_ID_1
Read/Write R/W R/W R/W R/W
Reset value
1 1 1 1
Register 0x24 (IEEE_ADDR_0):
This register contains the lower 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[7:0].
Figure 8-10. Register IEEE_ADDR_0.
Bit 7 6 5 4
0x24
IEEE_ADDR_0
IEEE_ADDR_0
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x24
IEEE_ADDR_0
IEEE_ADDR_0
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
93
Register 0x25 (IEEE_ADDR_1):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[15:8].
Figure 8-11. Register IEEE_ADDR_1.
Bit 7 6 5 4
0x25
IEEE_ADDR_1
IEEE_ADDR_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x25
IEEE_ADDR_1
IEEE_ADDR_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Register 0x26 (IEEE_ADDR_2):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[23:16].
Figure 8-12. Register IEEE_ADDR_2.
Bit
7
6
5
4
0x26 IEEE_ADDR_2 IEEE_ADDR_2
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x26 IEEE_ADDR_2 IEEE_ADDR_2
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Register 0x27 (IEEE_ADDR_3):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[31:24].
Figure 8-13. Register IEEE_ADDR_3.
Bit
7
6
5
4
0x27 IEEE_ADDR_3 IEEE_ADDR_3
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x27 IEEE_ADDR_3 IEEE_ADDR_3
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
94
Register 0x28 (IEEE_ADDR_4):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[39:32].
Figure 8-14. Register IEEE_ADDR_4.
Bit
7
6
5
4
0x28 IEEE_ADDR_4 IEEE_ADDR_4
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x28 IEEE_ADDR_4 IEEE_ADDR_4
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Register 0x29 (IEEE_ADDR_5):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[47:40].
Figure 8-15. Register IEEE_ADDR_5.
Bit 7 6 5 4
0x29
IEEE_ADDR_5
IEEE_ADDR_5
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x29
IEEE_ADDR_5
IEEE_ADDR_5
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Register 0x2A (IEEE_ADDR_6):
This register contains 8-bit of the MAC IEEE address for Frame Filter address
recognition, bits[55:48].
Figure 8-16. Register IEEE_ADDR_6.
Bit 7 6 5 4
0x2A
IEEE_ADDR_6
IEEE_ADDR_6
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x2A
IEEE_ADDR_6
IEEE_ADDR_6
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
95
Register 0x2B (IEEE_ADDR_7):
This register contains the higher 8-bit of the MAC IEEE Frame Filter address for
address recognition, bits[63:56].
Figure 8-17. Register IEEE_ADDR_7.
Bit
7
6
5
4
0x2B IEEE_ADDR_7 IEEE_ADDR_7
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x2B IEEE_ADDR_7 IEEE_ADDR_7
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
96
8.3 Frame Check Sequence (FCS)
The Frame Check Sequence (FCS) is characterized by:
• Indication of bit errors, based on a cyclic redundancy check (CRC) of length 16 bit
• A use of International Telecommunication Union (ITU) CRC polynomial
• Automatical evaluation during reception
• Automatical generation during transmission
8.3.1 Overview
The FCS is intended for use at the MAC layer to detect corrupted frames at a first level
of filtering. It is computed by applying an ITU CRC polynomial to all transferred bytes
following the length field (MHR and MSDU fields). The frame check sequence has a
length of 16 bit and is located in the last two bytes of a frame (MAC footer, see Figure
8-2).
The Atmel AT86RF233 applies an FCS check on each received frame. The FCS check
result is stored in register bit RX_CRC_VALID (register 0x06, PHY_RSSI).
On transmission the radio transceiver generates and appends the FCS bytes during the
frame transmission. This behavior can be disabled by setting register bit
TX_AUTO_CRC_ON = 0 (register 0x04, TRX_CTRL_1).
8.3.2 CRC Calculation
The CRC polynomial used in IEEE 802.15.4 networks is defined by
1)(
51216
16 +++= xxxxG
.
The FCS shall be calculated for transmission using the following algorithm:
Let
12
2
1
1
0
)( −−
−− ++++= kk
kk bxbxbxb
xM
be the polynomial representing the sequence of bits for which the checksum is to be
computed. Multiply M(x) by
16
x
, giving the polynomial
16
)()( xxMxN ⋅=
.
Divide
)(xN
modulo two by the generator polynomial,
)(
16
xG
, to obtain the remainder
polynomial,
1514
14
1
15
0...)( rxrxr
xrxR ++++=
.
The FCS field is given by the coefficients of the remainder polynomial, R(x).
Example:
Considering a five octet ACK frame. The MHR field consists of
0100 0000 0000 0000 0101 0110.
The leftmost bit (b0) is transmitted first in time. The FCS is in this case
0010 0111 1001 1110.
The leftmost bit (r0) is transmitted first in time.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
97
8.3.3 Automatic FCS Generation
The automatic FCS generation is activated with register bit TX_AUTO_CRC_ON = 1.
This allows the Atmel AT86RF233 to compute the FCS autonomously. For a frame with
a frame length specified as N (3 ≤ N ≤ 127), the FCS is calculated on the first N-2 octets
in the Frame Buffer, and the resulting FCS field is transmitted in place of the last two
octets from the Frame Buffer.
If the radio transceiver’s automatic FCS generation is enabled, the Frame Buffer write
access can be stopped right after MAC payload. There is no need to write FCS dummy
bytes.
In RX_AACK mode, when a received frame needs to be acknowledged, the FCS of the
ACK frame is always automatically generated by the AT86RF233, independent of the
TX_AUTO_CRC_ON setting.
Example:
A frame transmission of length five with TX_AUTO_CRC_ON set, is started with a
Frame Buffer write access of five bytes (the last two bytes can be omitted). The first
three bytes are used for FCS generation; the last two bytes are replaced by the
internally calculated FCS.
8.3.4 Automatic FCS Check
An automatic FCS check is applied on each received frame with a frame length N ≥ 2.
Register bit RX_CRC_VALID (register 0x06, PHY_RSSI) is set if the FCS of a received
frame is valid. The register bit is updated when issuing interrupt IRQ_3 (TRX_END) and
remains valid until the next TRX_END interrupt caused by a new frame reception. In
addition, bit[7] of byte RX_STATUS is set accordingly, refer to Section 6.3.2.
In Extended Operating Mode, the RX_AACK procedure does not accept a frame if the
corresponding FCS is not valid, that is no IRQ_3 (TRX_END) interrupt is issued. When
operating in TX_ARET mode, the FCS of a received ACK is automatically checked. If it
is not correct, the ACK is not accepted; refer to Section 7.2.4 for automated retries.
8.3.5 Register Description
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 8-18. Register TRX_CTRL_1.
Bit 7 6 5 4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
98
• Bit 5 - TX_AUTO_CRC_ON
The register bit TX_AUTO_CRC_ON controls the automatic FCS generation for
transmit operations.
Table 8-13. TX_AUTO_CRC_ON.
Register Bits Value Description
TX_AUTO_CRC_ON 0 Automatic FCS generation is disabled
1 Automatic FCS generation is enabled
Note: 1.
The TX_AUTO_CRC_ON function can be used within Basic and Extended
Operating Modes.
Register 0x06 (PHY_RSSI):
The PHY_RSSI register is a multi-purpose register that indicates FCS validity, to
provide random numbers, and a RSSI value.
Figure 8-19. Register PHY_RSSI.
Bit
7
6
5
4
0x06
RX_CRC_VALID
RND_VALUE
RSSI
PHY_RSSI
Read/Write
R
R
R
R
Reset value
0
1
1
0
Bit
3
2
1
0
0x06
RSSI
PHY_RSSI
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7 - RX_CRC_VALID
The register bit RX_CRC_VALID signals the FCS check status for a received frame.
Table 8-14. RX_CRC_VALID.
Register Bits Value Description
RX_CRC_VALID 0 FCS is not valid
1 FCS is valid
Reading this register bit indicates whether the last received frame has a valid FCS or
not. The register bit is updated when issuing interrupt IRQ_3 (TRX_END) and remains
valid until the next TRX_END interrupt is issued, caused by a new frame reception.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
99
8.4 Received Signal Strength Indicator (RSSI)
The Atmel AT86RF233 Received Signal Strength Indicator is characterized by:
• Minimum RSSI level is -94dBm (RSSIBASE_VAL)
• Dynamic range is 87dB
• Minimum RSSI value is 0
• Maximum RSSI value is 28
8.4.1 Overview
The RSSI is a 5-bit value indicating the receive power in the selected channel, in steps
of 3dB. No attempt is made to distinguish IEEE 802.15.4 signals from others, only the
received signal strength is evaluated. The RSSI provides the basis for an ED
measurement, see Section 8.5.
8.4.2 Reading RSSI
In Basic Operating Modes, the RSSI value is valid in any receive state and is updated
every tRSSI = 2µs. The current RSSI value can be accessed by reading register bits
RSSI (register 0x06, PHY_RSSI).
It is not recommended reading the RSSI value when using the Extended Operating
Modes or Smart Receiving, see Section 11.10.2.2. Instead, the automatically generated
ED value should be used, see Section 8.5.
8.4.3 Data Interpretation
The RSSI value is a 5-bit value in a range of zero to 28, indicating the receiver input
power in steps of about 3dB.
A RSSI value of zero indicates a receiver RF input power of PRF ≤ -94dBm. For a RSSI
value in the range of one to 28, the RF input power can be calculated as follows:
PRF[dBm] = RSSIBASE_VAL[dBm] + 3[dB] x RSSI
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
100
8.4.4 Register Description
Register 0x06 (PHY_RSSI):
The PHY_RSSI register is a multi-purpose register that indicates FCS validity, to
provide random numbers, and a RSSI value.
Figure 8-20. Register PHY_RSSI.
Bit 7 6 5 4
0x06
RX_CRC_VALID
RND_VALUE
RSSI
PHY_RSSI
Read/Write R R R R
Reset value
0 1 1 0
Bit 3 2 1 0
0x06
RSSI
PHY_RSSI
Read/Write R R R R
Reset value
0 0 0 0
• Bit 4:0 - RSSI
Received signal strength as a linear curve on a logarithmic input power scale with a
resolution of 3dB.
Table 8-15. RSSI.
Register Bits Value Description
RSSI 0x00 Minimum RSSI value
0x1C Maximum RSSI value
The result of the automated RSSI measurement is stored in register bits RSSI
(register 0x06, PHY_RSSI). The value is updated every tRSSI = 2µs in any receive state.
The read value is a number between zero and 28 indicating the received signal strength
as a linear curve on a logarithmic input power scale with a resolution of 3dB. An RSSI
value of zero indicates an RF input power of PRF ≤ -94dBm (RSSIBASE_VAL), a value of 28
a power of PRF ≥ -10dBm (see parameter RSSIMAX specified in Section 12.7).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
101
8.5 Energy Detection (ED)
The Atmel AT86RF233 Energy Detection (ED) module is characterized by:
• 84 unique energy levels defined
• 1dB resolution
• A measurement time of eight symbol periods for IEEE 802.15.4 compliant data rates
8.5.1 Overview
The receiver ED measurement (ED scan procedure) can be used as a part of a channel
selection algorithm. It is an estimation of the received signal power within the bandwidth
of an IEEE 802.15.4 channel. No attempt is made to identify or decode signals on the
channel. The ED value is calculated by averaging RSSI values over eight symbols
(128µs).
For High Data Rate Modes the automated ED measurement duration is reduced to
32µs, refer to Section 11.3. For manually initiated ED measurements in these modes
the measurement period is still 128µs as long as the receiver is in RX_ON state.
8.5.2 Measurement Description
There are two ways to initiate an ED measurement:
• Manually, by writing an arbitrary value to register 0x07 (PHY_ED_LEVEL), or
• Automatically, after detection of a valid SHR of an incoming frame.
Manually:
For manually initiated ED measurements, the radio transceiver needs to be
either in the state RX_ON or BUSY_RX. The end of the ED measurement time
(eight symbol periods plus a processing time) is indicated by the interrupt
IRQ_4 (CCA_ED_DONE) and the measurement result is stored in register 0x07
(PHY_ED_LEVEL), refer to tED in Table 7-2.
In order to avoid interference with an automatically initiated ED measurement,
the SHR detection can be disabled by setting register bit RX_PDT_DIS
(register 0x15, RX_SYN), refer to Section 9.1.
Note: 1. It is not recommended to manually initiate an ED measurement when using the
Extended Operating Mode.
Automatically:
An automated ED measurement is started upon SHR detection. The end of the
automated measurement is not signaled by an interrupt.
When using Basic Operating Mode, a valid ED value from the currently
received frame is accessible 108µs after IRQ_2 (RX_START) and remains
valid until a new RX_START interrupt is generated by the next incoming frame
or until another ED measurement is initiated.
When using the Extended Operating Mode, it is recommended to mask
IRQ_2 (RX_START), thus the interrupt cannot be used as timing reference. A
successful frame reception is signalized by interrupt IRQ_3 (TRX_END). The
minimum time span between an IRQ_3 (TRX_END) interrupt and a following
SFD detection is tSHR_SYNC = 96µs due to the length of the SHR. Including the
ED measurement time, the ED value needs to be read within 224µs after the
TRX_END interrupt; otherwise, it could be overwritten by the result of the next
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
102
measurement cycle. This is important for time critical applications or if interrupt
IRQ_2 (RX_START) is not used to indicate the reception of a frame.
Note: 2.
The ED result is not updated during the rest of the frame reception, even by
requesting an ED measurement manually.
8.5.3 Data Interpretation
The PHY_ED_LEVEL is an 8-bit register. The ED_LEVEL value of the
Atmel AT86RF233 has a valid range from 0x00 to 0x53 with a resolution of 1dB. Values
0x54 to 0xFE do not occur and a value of 0xFF indicates the reset value.
Due to environmental conditions (temperature, voltage, semiconductor parameters,
etc.) the calculated ED_LEVEL value has a maximum tolerance of ±5dB, this is to be
considered as constant offset over the measurement range.
An ED_LEVEL value of zero indicates a receiver RF input power of PRF ≤ -94dBm (see
parameter RSSIBASE_VAL, Section 12.7). For an ED_LEVEL value in the range of one to
83, the RF input power can be calculated as follows:
PRF[dBm] = RSSIBASE_VAL[dBm] + 1[dB] x ED_LEVEL
8.5.4 Interrupt Handling
Interrupt IRQ_4 (CCA_ED_DONE) is issued at the end of a manually initiated ED
measurement.
Note: 1. An ED request should only be initiated in receive states. Otherwise the radio
transceiver generates an IRQ_4 (CCA_ED_DONE)
; however no ED
measurement was performed.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
103
8.5.5 Register Description
Register 0x07 (PHY_ED_LEVEL):
The PHY_ED_LEVEL register contains the result of an ED measurement.
Figure 8-21. Register PHY_ED_LEVEL.
Bit 7 6 5 4
0x07
ED_LEVEL
PHY_ED_LEVEL
Read/Write R R R R
Reset value
1 1 1 1
Bit 3 2 1 0
0x07
ED_LEVEL
PHY_ED_LEVEL
Read/Write R R R R
Reset value
1 1 1 1
• Bit 7:0 - ED_LEVEL
The register bits ED_LEVEL signals the ED level for the current channel.
Table 8-16. ED_LEVEL.
Register Bits Value Description
ED_LEVEL 0x00 Minimum ED level value
0x53 Maximum ED level value
0xFF Reset value
The minimum ED value zero indicates receiver power less than or equal RSSIBASE_VAL.
The range is 83dB with a resolution of 1dB and an accuracy of ±5dB. The value 0xFF
signals that no measurement has been started yet (reset value).
A manual ED measurement can be initiated by a write access to the register.
The measurement duration is eight symbol periods (128µs) for a data rate of 250kb/s.
For High Data Rate Modes the automated measurement duration is reduced to 32µs,
refer to Section 11.3. For manually initiated ED measurements in these modes the
measurement period is still 128µs as long as the receiver is in RX_ON state.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
104
8.6 Clear Channel Assessment (CCA)
The main features of the Clear Channel Assessment (CCA) module are:
• All four modes are available as defined by IEEE 802.15.4-2006 in Section 6.9.9
• Adjustable threshold for energy detection algorithm
8.6.1 Overview
A CCA measurement is used to detect a clear channel. Four CCA modes are specified
by IEEE 802.15.4-2006:
Table 8-17. CCA Mode Overview.
CCA Mode Description
1 Energy above threshold.
CCA shall report a busy medium upon detecting any energy above the ED
threshold.
2 Carrier sense only.
CCA shall report a busy medium only upon the detection of a signal with the
modulation and spreading characteristics of an IEEE 802.15.4 compliant signal.
The signal strength may be above or below the ED threshold.
0, 3 Carrier sense with energy above threshold.
CCA shall report a busy medium using a logical combination of
- Detection of a signal with the modulation and spreading characteristics of
this standard and
- Energy above the ED threshold.
Where the logical operator may be configured as either OR (mode 0) or
AND (mode 3).
8.6.2 Configuration and Request
The CCA modes are configurable via register 0x08 (PHY_CC_CCA).
When in Basic Operating Mode, an CCA request can be initiated manually by setting
CCA_REQUEST = 1 (register 0x08, PHY_CC_CCA), if the Atmel AT86RF233 is in any
RX state. The current channel status (CCA_STATUS) and the CCA completion status
(CCA_DONE) are accessible through register 0x01 (TRX_STATUS).
The CCA evaluation is done over eight symbol periods and the result is accessible
tCCA = 180µs (max.) (128µs measurement duration and processing delay) after the
request, refer to Table 7-2. The end of a manually initiated CCA measurement is
indicated by an interrupt IRQ_4 (CCA_ED_DONE).
The register bits CCA_ED_THRES (register 0x09, CCA_THRES) defines the receive
power threshold of the “energy above threshold” algorithm. The threshold is calculated
by:
PCCA_ED_THRES[dBm] = RSSIBASE_VAL[dBm] + 2[dB] x CCA_ED_THRES.
Any received power above this level is interpreted as a busy channel.
Note: 1. It is not recommended to manually initiate an CCA measurement when using
the Extended Operating Mode.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
105
8.6.3 Data Interpretation
The Atmel AT86RF233 current channel status (CCA_STATUS) and the CCA
completion status (CCA_DONE) are accessible through register 0x01 (TRX_STATUS).
Note: 1. The register bits CCA_DONE and CCA_STATUS are cleared in response to a
CCA_REQUEST.
The completion of a measurement cycle is indicated by CCA_DONE = 1. If the radio
transceiver detects no signal (idle channel) during the CCA evaluation period, the
CCA_STATUS bit is set to one; otherwise, it is set to zero.
When using the “energy above threshold” algorithm, a received power above
PCCA_ED_THRES is interpreted as a busy channel.
When using the “carrier sense” algorithm (that is CCA_MODE = 0, 2, and 3), the
AT86RF233 reports a busy channel upon detection of a PHY mode specific
IEEE 802.15.4 signal above RSSIBASE_VAL (see Section 12.7). The AT86RF233 is also
capable of detecting signals below this value, but the detection probability decreases
with decreasing signal power. It is almost zero at the radio transceivers sensitivity level
(see parameter PSENS on Section 12.7).
8.6.4 Interrupt Handling
Interrupt IRQ_4 (CCA_ED_DONE) is issued at the end of a manually initiated CCA
measurement.
Note: 1. A CCA request should only be initiated in Basic Operating Mode receive states.
Otherwise the radio transceiver generates an IRQ_4 (CCA_ED_DONE) and
sets the register bit CCA_DONE = 1, even though no CCA measurement was
performed.
8.6.5 Measurement Time
The response time for a manually initiated CCA measurement depends on the receiver
state.
In RX_ON state, the CCA measurement is done over eight symbol periods and the
result is accessible upon the event IRQ_4 (CCA_ED_DONE) or upon CCA_DONE = 1
(register 0x01, TRX_STATUS).
In BUSY_RX state, the CCA measurement duration depends on the CCA mode and the
CCA request relative to the detection of the SHR. The end of the CCA measurement is
indicated by IRQ_4 (CCA_ED_DONE). The variation of a CCA measurement period in
BUSY_RX state is described in Table 8-18.
It is recommended to perform CCA measurements in RX_ON state only. To avoid
switching accidentally to BUSY_RX state, the SHR detection can be disabled by setting
register bit RX_PDT_DIS (register 0x15, RX_SYN), refer to Section 9.1. The receiver
remains in RX_ON state to perform a CCA measurement until the register bit
RX_PDT_DIS is set back to continue the frame reception. In this case, the CCA
measurement duration is eight symbol periods.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
106
Table 8-18. CCA Measurement Period and Access in BUSY_RX state.
CCA Mode Request within ED measurement(1) Request after ED measurement
1 Energy above threshold.
CCA result is available after finishing
automated ED measurement period.
CCA result is immediately available
after request.
2 Carrier sense only.
CCA result is immediately available after request.
3 Carrier sense with Energy above threshold (AND).
CCA result is available after finishing
automated ED measurement period.
CCA result is immediately available
after request.
0 Carrier sense with Energy above threshold (OR).
CCA result is available after finishing
automated ED measurement period.
CCA result is immediately available
after request.
Note: 1. After detecting the SHR, an automated ED measurement is started with a length
of eight symbol periods (two symbol periods for high rate PHY modes, refer to
Section 8.5.
This automated ED measurement must be finished to provide a
result for the CCA measurement. Only one automated ED measurement per
frame is performed.
8.6.6 Register Description
Register 0x01 (TRX_STATUS):
The read-only register TRX_STATUS signals the present state of the radio transceiver
as well as the status of a CCA operation.
Figure 8-22. Register TRX_STATUS.
Bit
7
6
5
4
0x01 CCA_DONE CCA_STATUS reserved TRX_STATUS TRX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x01 TRX_STATUS TRX_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7 - CCA_DONE
Table 8-19. CCA_DONE.
Register Bits Value Description
CCA_DONE 0 CCA calculation not finished
1 CCA calculation finished
The register bit CCA_DONE indicates if a CCA request is completed. This is also
indicated by an interrupt IRQ_4 (CCA_ED_DONE). The register bit CCA_DONE is
cleared in response to a CCA_REQUEST.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
107
• Bit 6 - CCA_STATUS
Table 8-20. CCA_STATUS.
Register Bits Value Description
CCA_STATUS 0 Channel indicated as busy
1 Channel indicated as idle
After a CCA request is completed, the result of the CCA measurement is available in
register bit CCA_STATUS. The register bit CCA_STATUS is cleared in response to a
CCA_REQUEST.
Register 0x08 (PHY_CC_CCA):
The PHY_CC_CCA register is a multi-purpose register that controls CCA configuration,
CCA measurement, and the IEEE 802.15.4 channel setting.
Figure 8-23. Register PHY_CC_CCA.
Bit 7 6 5 4
0x08
CCA_REQUEST
CCA_MODE
CHANNEL
PHY_CC_CCA
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x08
CHANNEL
PHY_CC_CCA
Read/Write R/W R/W R/W R/W
Reset value
1 0 1 1
• Bit 7 - CCA_REQUEST
The register bit CCA_REQUEST initiates a manual started CCA measurement.
Table 8-21. CCA_REQUEST.
Register Bits Value Description
CCA_REQUEST 0 Reset value
1 Starts a CCA measurement
Notes: 1. The read value returns always with zero.
2.
If a CCA request is initiated in states others than RX_ON or RX_BUSY the PHY
generates an IRQ_4 (CCA_ED_DONE) and sets the register bit CCA_DONE,
however no CCA was carried out.
A manual CCA measurement is initiated with setting CCA_REQUEST = 1. The end of
the CCA measurement is indicated by interrupt IRQ_4 (CCA_ED_DONE). Register bits
CCA_DONE and CCA_STATUS (register 0x01, TRX_STATUS) are updated after a
CCA_REQUEST. The register bit is automatically cleared after requesting a CCA
measurement with CCA_REQUEST = 1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
108
• Bit 6:5 - CCA_MODE
The CCA mode can be selected using register bits CCA_MODE.
Table 8-22. CCA_MODE.
Register Bits Value Description
CCA_MODE 0 Mode 3a, Carrier sense OR energy above threshold
1 Mode 1, Energy above threshold
2 Mode 2, Carrier sense only
3 Mode 3b, Carrier sense AND energy above threshold
Note: 1. IEEE 802.15.4–
2006 CCA mode 3 defines the logical combination of CCA mode 1
and 2 with the logical operators AND or OR.
Register 0x09 (CCA_THRES):
The CCA_THRES register sets the ED threshold level for CCA.
Figure 8-24. Register CCA_THRES.
Bit
7
6
5
4
0x09
reserved
CCA_THRES
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
0
0
Bit
3
2
1
0
0x09
CCA_ED_THRES
CCA_THRES
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
1
1
1
• Bit 3:0 - CCA_ED_THRES
An ED value above the threshold signals the channel as busy during a CCA_ED
measurement.
Table 8-23. CCA_ED_THRES.
Register Bits Value Description
CCA_ED_THRES 0x7 For CCA_MODE = 1, a busy channel is indicated if the
measured received power is above P_THRES[dBm] =
RSSI_BASE_VAL[dBm] + 2[dB] x CCA_ED_THRES. CCA
modes 0 and 3 are logically related to this result.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
109
8.7 Link Quality Indication (LQI)
The IEEE 802.15.4 standard defines the LQI as a characterization of the strength
and/or quality of a received frame. The use of the LQI result by the network or
application layer is not specified in this standard. The LQI value shall be an integer
ranging from zero to 255, with at least eight unique values. The minimum and maximum
LQI values (0x00 and 0xFF) should be associated with the lowest and highest quality
compliant signals, respectively, and LQI values in between should be uniformly
distributed between these two limits.
8.7.1 Overview
The LQI measurement of the Atmel AT86RF233 is implemented as a measure of the
link quality which can be described with the packet error rate (PER) for this link. An LQI
value can be associated with an expected packet error rate. The PER is the ratio of
erroneous received frames to the total number of received frames. A PER of zero
indicates no frame error, whereas at a PER of one no frame was received correctly.
The radio transceiver uses correlation results of multiple symbols within a frame to
determine the LQI value. This is done for each received frame. The minimum frame
length for a valid LQI value is two octets PSDU. LQI values are integers ranging from
zero to 255.
As an example, Figure 8-27 shows the conditional packet error rate (PER) when
receiving a certain LQI value.
Figure 8-25. Conditional Packet Error Rate versus LQI.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0 50 100 150 200 250
PER
LQI
That means that a large number of transmission with an identical LQI value results in a
packet error rate shown in the Figure 8-27. Lost packets have been discarded since in
this case there is no LQI value available.
If, instead, the mean LQI over a large number of transmissions is computed, and the
mean LQI is quantized to an LQI value of the figure, the corresponding frame error rate
is not strictly equal to the true error rate.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
110
The values are taken from received frames of PSDU length of 20 octets on
transmission channels with reasonable low multipath delay spreads. If the transmission
channel characteristic has higher multipath delay spread than assumed in the example,
the PER is slightly higher for a certain LQI value.
Since the packet error rate is a statistical value, the PER shown in Figure 8-27 is based
on a huge number of transactions. A reliable estimation of the packet error rate cannot
be based on a single or a small number of LQI values.
8.7.2 Obtaining the LQI Value
The LQI value is available, once the corresponding frame has been completely
received. This is indicated by the interrupt IRQ_3 (TRX_END). The value can be
obtained by means of a frame buffer read access, see Section 6.3.2.
8.7.3 Data Interpretation
The reason for a low LQI value can be twofold: a low signal strength and/or high signal
distortions, for example by interference and/or multipath propagation. High LQI values,
however, indicate a sufficient signal strength and low signal distortions.
Notes: 1. T
he LQI value is almost always 255 for scenarios with very low signal
distortions and a signal strength much greater than the sensitivity level. In this
case, the packet error rate tends towards zero and increase of the signal
strength, that is
by increasing the transmission power, cannot decrease the
error rate any further. Received signal strength indication (RSSI) or energy
detection (ED) can be used to evaluate the signal strength and the link margin.
2.
The received signal power as indicated by received signal strength indication
(RSSI) value or energy detection (ED) value of the Atmel AT86RF233 do not
characterize the signal quality and the ability to decode a signal.
ZigBee networks often require identification of the “best” routing between two nodes.
LQI and RSSI/ED can be applied, depending on the optimization criteria. If a low frame
error rate (corresponding to a high throughput) is the optimization criteria, then the LQI
value should be taken into consideration. If, however, the target is a low transmission
power, then the RSSI/ED value is also helpful.
Various combinations of LQI and RSSI/ED are possible for routing decisions. As a rule
of thumb, information on RSSI/ED is useful in order to differentiate between links with
high LQI values. However, transmission links with low LQI values should be discarded
for routing decisions, even if the RSSI/ED values are high, since it is merely an
information about the received signal strength, whereas the source can be an interferer.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
111
9 Module Description
9.1 Receiver (RX)
9.1.1 Overview
The Atmel AT86RF233 receiver is split into an analog radio front-end and a digital base
band processor (RX BBP), see Figure 9-1.
Figure 9-1. Receiver Block Diagram.
LNA PPF BPF Limiter ADC
AGC RSSI
RFP
RFN
Analog Domain Digital Domain
SPI
RX BBP
Frame
Buffer
LO
Control, Registers
SPI
I/F
µC
I/F
The differential RF signal is amplified by a low noise amplifier (LNA), filtered (PPF) and
down converted to an intermediate frequency by a mixer. Channel selectivity is
performed using an integrated band pass filter (BPF). A limiting amplifier (Limiter)
provides sufficient gain to overcome the DC offset of the succeeding analog-to-digital
converter (ADC) and generates a digital RSSI signal. The ADC output signal is sampled
and processed further by the digital base band receiver (RX BBP).
The RX BBP performs additional signal filtering and signal synchronization. The
frequency offset of each frame is calculated by the synchronization unit and is used
during the remaining receive process to correct the offset. The receiver is designed to
handle frequency and symbol rate deviations fSRD up to ±120ppm, caused by combined
receiver and transmitter deviations. For details refer to Section 12.5 parameter fSRD.
Finally the signal is demodulated and the data are stored in the Frame Buffer.
In Basic Operating Mode, refer to Section 7.1, the reception of a frame is indicated by
an interrupt IRQ_2 (RX_START). Accordingly its end is signalized by an interrupt
IRQ_3 (TRX_END). Based on the quality of the received signal a link quality indicator
(LQI) is calculated and appended to the frame, refer to Section 8.7. Additional signal
processing is applied to the frame data to provide further status information like ED
value (register 0x07, PHY_ED_LEVEL) and FCS correctness (register 0x06,
PHY_RSSI).
Beyond these features the Extended Operating Mode of the AT86RF233 supports
address filtering and pending data indication. For details refer to Section 7.2.
9.1.2 Frame Receive Procedure
The frame receive procedure including the radio transceiver setup for reception and
reading PSDU data from the Frame Buffer is described in Section 10.1 Frame Receive
Procedure.
9.1.3 Configuration
In Basic Operating Mode the receiver is enabled by writing command RX_ON to
register bits TRX_CMD (register 0x02, TRX_STATE) in states TRX_OFF or PLL_ON.
Similarly in Extended Operating Mode, the receiver is enabled for RX_AACK operation
from states TRX_OFF, PLL_ON or TX_ARET_ON by writing the command
RX_AACK_ON.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
112
There is no additional configuration required to receive IEEE 802.15.4 compliant frames
when using the Basic Operating Mode. However, the frame reception in the
Atmel AT86RF233 Extended Operating Mode requires further register configurations,
for details refer to Section 7.2.
The AT86RF233 receiver has an outstanding sensitivity performance of -101dBm. At
certain environmental conditions or for High Data Rate Modes, refer to Section 11.3, it
may be useful to manually decrease this sensitivity. This is achieved by adjusting the
synchronization header detector threshold using register bits RX_PDT_LEVEL
(register 0x15, RX_SYN). Received signals with a RSSI value below the threshold do
not activate the demodulation process.
Furthermore, it may be useful to protect a received frame against overwriting by
subsequent received frames. A Dynamic Frame Buffer Protection is enabled with
register bit RX_SAFE_MODE (register 0x0C, TRX_CTRL_2) set, see Section 11.8. The
receiver remains in RX_ON or RX_AACK_ON state until the whole frame is uploaded
by the microcontroller, indicated by pin 23 (/SEL) = H during the SPI Frame Receive
Mode. The Frame Buffer content is only protected if the FCS is valid.
A Static Frame Buffer Protection is enabled with register bit RX_PDT_DIS
(register 0x15, RX_SYN) set. The receiver remains in RX_ON or RX_AACK_ON state
and no further SHR is detected until the register bit RX_PDT_DIS is set back.
9.1.4 Register Description
Register 0x15 (RX_SYN):
The register RX_SYN controls the blocking of receiver path and the sensitivity threshold
of the receiver.
Figure 9-2. Register RX_SYN.
Bit 7 6 5 4
0x15
RX_PDT_DIS
reserved
RX_SYN
Read/Write R/W R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x15
RX_PDT_LEVEL
RX_SYN
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
• Bit 7 - RX_PDT_DIS
The register bit RX_PDT_DIS prevents the reception of a frame during RX phase.
Table 9-1. RX_PDT_DIS.
Register Bits Value Description
RX_PDT_DIS 0 RX path is enabled
1 RX path is disabled
RX_PDT_DIS = 1 prevents the reception of a frame even if the radio transceiver is in
receive modes. An ongoing frame reception is not affected. This operation mode is
independent of the setting of register bits RX_PDT_LEVEL.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
113
• Bit 3:0 - RX_PDT_LEVEL
The register bits RX_PDT_LEVEL desensitize the receiver in steps of 3dB.
Table 9-2. RX_PDT_LEVEL.
Register Bits Value Description
RX_PDT_LEVEL 0x00 Maximum RX sensitivity
0x0F RX input level[dBm] >
RSSI_BASE_VAL[dBm] + 3[dB] x 14
These register bits desensitize the receiver such that frames with an RSSI level below
the RX_PDT_LEVEL threshold level (if RX_PDT_LEVEL > 0) are not received. For a
RX_PDT_LEVEL > 0 value the threshold level can be calculated according to the
following formula:
PRF[dBm] > RSSIBASE_VAL[dBm] + 3[dB] x (RX_PDT_LEVEL - 1).
Examples for certain register settings are given in Table 9-3.
Table 9-3. Receiver Desensitization Threshold Level – RX_PDT_LEVEL.
Register Value RX Input Threshold Level Value [dBm]
0x0 ≤ RSSI_BASE_VAL (reset value) RSSI value not considered
0x1 > RSSI_BASE_VAL + 3[db] x 0 > -94
…
0xE > RSSI_BASE_VAL + 3[db] x 13 > -55
0xF > RSSI_BASE_VAL + 3[db] x 14 > -52
If register bits RX_PDT_LEVEL = 0 (reset value) all frames with a valid SHR and PHR
are received, independently of their signal strength.
If register bits RX_PDT_LEVEL > 0, the current consumption of the receiver in all RX
listening states is reduced to IRX_ON_L0 = 11.3mA (typ.), refer to Section 12.8.
Additional power saving techniques in receive modes are specified in Section 11.10.
Register 0x3C (TST_AGC):
Figure 9-3. Register TST_AGC.
Bit 7 6 5 4
0x3C
reserved
AGC_HOLD_SEL
AGC_RST
TST_AGC
Read/Write R R R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x3C
AGC_OFF
AGC_HOLD
GC
TST_AGC
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Note: 1.
The register bits can be read or written, the values will effect the device operation
only if the register bit PMU_EN (register 0x03, TRX_CTRL_0) is set, otherwise
reset values will be applied.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
114
• Bit 5 - AGC_HOLD_SEL
The register bit AGC_HOLD_SEL controls the AGC operation mode.
Table 9-4. AGC_HOLD_SEL.
Register Bits Value Description
AGC_HOLD_SEL 0 Normal operation is selected
1 Manual control of AGC operation is selected. Used setting
from register bit AGC_HOLD.
• Bit 4 - AGC_RST
The register bit AGC_RST resets the AGC receiver gain contol to maximum gain.
Table 9-5. AGC_RST.
Register Bits Value Description
AGC_RST 0 No AGC gain contol reset
1 AGC gain contol reset
• Bit 3 - AGC_OFF
The register bit AGC_OFF disables automatic AGC gain regulation. Allows manual
receiver gain setting with register bits GC.
Table 9-6. AGC_OFF.
Register Bits Value Description
AGC_OFF 0 Automatic AGC gain regulation is switched on
1 Automatic AGC gain regulation is switched off
• Bit 2 - AGC_HOLD
The register bit AGC_HOLD controls the AGC running mode.
Table 9-7. AGC_HOLD.
Register Bits Value Description
AGC_HOLD 0 AGC is within free running mode
1 AGC running mode is frozen
• Bit 1:0 - GC
The register bits GC control the receiver gain. A setting of register bits GC effect the
device operation only if register bit AGC_OFF is set.
Table 9-8. GC.
Register Bits Value Description
GC 0 Set receiver path to maximum gain
1 Set receiver path to medium gain
2 Set receiver path to minimum gain
All other values are reserved
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
115
9.2 Transmitter (TX)
9.2.1 Overview
The Atmel AT86RF233 transmitter consists of a digital base band processor (TX BBP)
and an analog radio front end, see Figure 9-4.
Figure 9-4. Transmitter Block Diagram.
PLL – TX Modulation
PA
Ext. RF front-end and
Output Power Control
SPI
I/F
DIG3/4
RFP
RFN
TX Data
Analog Domain Digital Domain
TX BBP
Frame
Buffer
Control, Registers
SPI
µC
I/F
Buf
The TX BBP reads the frame data from the Frame Buffer and performs the bit-to-
symbol and symbol-to-chip mapping as specified by IEEE 802.15.4 in Section 6.5.2.
The O-QPSK modulation signal is generated and fed into the analog radio front end.
The fractional-N frequency synthesizer (PLL) converts the baseband transmit signal to
the RF signal, which is amplified by the power amplifier (PA). The PA output is internally
connected to bidirectional differential antenna pins (RFP, RFN), so that no external
antenna switch is needed.
9.2.2 Frame Transmit Procedure
The frame transmit procedure including writing PSDU data in the Frame Buffer and
initiating a transmission is described in Section 10.2.
9.2.3 Configuration
The maximum output power of the transmitter is typically +4dBm. The output power can
be configured via register bits TX_PWR (register 0x05, PHY_TX_PWR). The output
power of the transmitter can be controlled over a range of 21dB.
A transmission can be started from PLL_ON or TX_ARET_ON state by a rising edge of
pin 11 (SLP_TR) or by writing TX_START command to register bits TRX_CMD
(register 0x02, TRX_STATE).
Figure 9-5. TX Power Ramping for maximum TX Power.
06 8 10
TRX_STATE
SLP_TR
PLL_ON
212 14 16 18 Length [μs]
PA buffer
4
PA
Modulation 1 1 0 0 0 00 01
BUSY_TX
1 0 0 1 0 10 110 1 1 0 1 01 00
0 1
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
116
9.2.4 TX Power Ramping
To optimize the output power spectral density (PSD), the PA buffer and PA are enabled
sequentially, see in Figure 9-5. In this example the transmission is initiated with the
rising edge of pin 11 (SLP_TR). The radio transceiver state changes from PLL_ON to
BUSY_TX. The modulation of the frame starts 16µs after pin 11 (SLP_TR) rising edge.
9.2.5 Register Description
Register 0x05 (PHY_TX_PWR):
The PHY_TX_PWR register controls the output power of the transmitter.
Figure 9-6. Register PHY_TX_PWR.
Bit 7 6 5 4
0x05
reserved
PHY_TX_PWR
Read/Write R R/W R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x05
TX_PWR
PHY_TX_PWR
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
• Bit 3:0 – TX_PWR
The register bits TX_PWR determine the TX output power of the radio transceiver.
Table 9-9. TX Output Power.
Register Bits Value TX Output Power [dBm]
TX_PWR 0x0 +4
0x1 +3.7
0x2
+3.4
0x3
+3
0x4 +2.5
0x5
+2
0x6
+1
0x7
0
0x8
-1
0x9
-2
0xA -3
0xB
-4
0xC
-6
0xD
-8
0xE
-12
0xF -17
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
117
Note: 1. A state change that is a command gets written to the TRX_CMD field resets the
value of the TX_PWR fields to the originally set value.
2.
If the extended operating mode is used with RPC enabled (that is
XAH_TX_RPC_EN is set to one), the read value of the TX_PWR field provides
the used transmit power for last transmitted frame including acknowledgement
frame. The TX_PWR field contains only the value of the RPC-controlled
transmission if a frame has already been sent. This allows monitoring the actual
RPC handling used for transmitting.
Register 0x3B (PHY_TX_TIME) for TOM_EN=0x01:
Figure 9-7. Register PHY_TX_TIME.
Bit 7 6 5 4
0x3B
reserved
PHY_TX_TIME
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x3B
IRC_TX_TIME
PHY_TX_TIME
Read/Write R R R R
Reset value
0 0 0 0
Notes: 1. If PMU mode is active, signals 8-bit PMU measurement value.
2. If TOM mode is active, signals 4-bit IRC_TX_TIME value.
• Bit 3:0 - IRC_TX_TIME
The register bits IRC_TX_TIME signals the alignment between rising edge of
pin 11 (SLP_TR) to 1MHz CLKM clock.
Table 9-10. IRC_TX_TIME.
Register Bits Value Description
IRC_TX_TIME 0x00 Signals 4-bit IRC_TX_TIME measurement value. The
resolution is 1/16MHz.
Valid values are [0xF, 0xE, …, 0x0].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
118
9.3 Frame Buffer
The Atmel AT86RF233 contains a 128 byte dual port SRAM. One port is connected to
the SPI interface, the other one to the internal transmitter and receiver modules. For
data communication, both ports are independent and simultaneously accessible.
The Frame Buffer utilizes the SRAM address space 0x00 to 0x7F for RX and TX
operation of the radio transceiver and can keep a single IEEE 802.15.4 RX or a single
TX frame of maximum length at a time.
Frame Buffer access modes are described in Section 6.3.2. Frame Buffer access
conflicts are indicated by an under run interrupt IRQ_6 (TRX_UR).
Note: 1. The IRQ_6 (TRX_UR)
interrupt also occurs on the attempt to write frames
longer than 127 octets to the Frame Buffer (overflow). In that case the content
of the Frame Buffer cannot be guaranteed.
Frame Buffer access is only possible if the digital voltage regulator (DVREG) is turned
on. This is valid in all device states except in SLEEP or DEEP_SLEEP state. An access
in P_ON state is possible if pin 17 (CLKM) provides the 1MHz master clock.
9.3.1 Data Management
Data in Frame Buffer (received data or data to be transmitted) remains valid as long as:
• No new frame or other data are written into the buffer over SPI
• No new frame is received (in any BUSY_RX state)
• No state change into SLEEP or DEEP_SLEEP state is made
• No RESET took place
By default there is no protection of the Frame Buffer against overwriting. Therefore, if a
frame is received during Frame Buffer read access of a previously received frame,
interrupt IRQ_6 (TRX_UR) is issued and the stored data might be overwritten.
Even so, the old frame data can be read, if the SPI data rate is higher than the effective
over air data rate. For a data rate of 250kb/s a minimum SPI clock rate of 1MHz is
recommended. Finally the microcontroller should check the transferred frame data
integrity by an FCS check.
To protect the Frame Buffer content against being overwritten by newly incoming
frames, the radio transceiver state should be changed to PLL_ON state after reception.
This can be achieved by writing immediately the command PLL_ON to register bits
TRX_CMD (register 0x02, TRX_STATE) after receiving the frame, indicated by
IRQ_3 (TRX_END). Alternatively, Dynamic Frame Buffer Protection can be used to
protect received frames against overwriting, for details refer to Section 11.8. Both
procedures do not protect the Frame Buffer from overwriting by the microcontroller.
In Extended Operating Mode during TX_ARET operation, see Section 7.2.4, the radio
transceiver switches to receive, if an acknowledgement of a previously transmitted
frame was requested. During this period received frames are evaluated, but not stored
in the Frame Buffer. This allows the radio transceiver to wait for an acknowledgement
frame and retry the frame transmission without writing them again.
A radio transceiver state change, except a transition to SLEEP, DEEP_SLEEP, or
RESET state, does not affect the Frame Buffer contents. If the radio transceiver is
forced into SLEEP or DEEP_SLEEP, the Frame Buffer is powered off and the stored
data gets lost.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
119
9.3.2 User accessible Frame Content
The Atmel AT86RF233 supports an IEEE 802.15.4 compliant frame format as shown in
Figure 9-8.
Figure 9-8. AT86RF233 Frame Structure.
Preamble Sequence SFD PHR Payload LQI
(1)
FCS
04 5 6 n + 3 n + 5 n + 6
Frame
Access SHR not accesible
RX: Frame Buffer content
PHY generated
Length [octets]
Duration 4 octets 1n octets (n <= 128) 3 octets
TX: Frame Buffer content
ED
(1) RX_STATUS(1)
n + 7 n + 8
Note: 1. Stored into Frame Buffer during frame reception.
A frame comprises two sections, the radio transceiver internally generated SHR field
and the user accessible part stored in the Frame Buffer. The SHR contains the
preamble and the SFD field. The variable frame section contains the PHR and the
PSDU including the FCS, see Section 8.3.
To access the data follow the procedures described in Section 6.3.2.
The frame length information (PHR field) and the PSDU are stored in the Frame Buffer.
During frame reception, the link quality indicator (LQI) value, the energy detection (ED)
value, and the status information (RX_STATUS) of a received frame are additionally
stored, see Section 8.7, Section 8.5, and Section 6.3.2, respectively. The radio
transceiver appends these values to the frame data during Frame Buffer read access.
If the SRAM read access is used to read an RX frame, the frame length field (PHR) can
be accessed at address zero. The SHR (except the SFD value used to generate the
SHR) cannot be read by the microcontroller.
For frame transmission, the PHR and the PSDU needs to be stored in the Frame
Buffer. The maximum Frame Buffer size supported by the radio transceiver is
128 bytes. If the register bit TX_AUTO_CRC_ON is set in register 0x04
(TRX_CTRL_1), the FCS field of the PSDU is replaced by the automatically calculated
FCS during frame transmission. There is no need to write the FCS field when using the
automatic FCS generation.
To manipulate individual bytes of the Frame Buffer a SRAM write access can be used
instead.
For non IEEE 802.15.4 compliant frames, the minimum frame length supported by the
radio transceiver is one byte (Frame Length Field + one byte of data).
9.3.3 Interrupt Handling
Access conflicts may occur when reading and writing data simultaneously at the two
independent ports of the Frame Buffer, TX/RX BBP and SPI. These ports have their
own address counter that points to the Frame Buffer’s current address.
Access violations may cause data corruption and are indicated by IRQ_6 (TRX_UR)
interrupt when using the Frame Buffer access mode. Note that access violations are not
indicated when using the SRAM access mode.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
120
While receiving a frame, primarily the data needs to be stored in the Atmel AT86RF233
Frame Buffer before reading it. This can be ensured by accessing the Frame Buffer
32µs after IRQ_2 (RX_START) at the earliest. When reading the frame data
continuously the SPI data rate shall be lower than 250kb/s to ensure no under run
interrupt occurs. To avoid access conflicts and to simplify the Frame Buffer read access
Frame Buffer Empty indication may be used, for details refer to Section 11.7.
During transmission, an access violation occurs on Frame Buffer write access, when
the SPI port’s address counter value becomes less than or equal to that of TX BBP
port.
Both these access violations may cause data corruption and are indicated by
IRQ_6 (TRX_UR) interrupt when using the Frame Buffer access mode. Access
violations are not indicated when using the SRAM access mode.
Notes: 1. Interrupt IRQ_6 (TRX_UR) is valid 64µs after IRQ_2 (RX_START)
. The
occurrence of the interrupt can be disregarded when reading the first byte of the
Frame Buffer between 32µs and 64µs after the RX_START interrupt.
2. If a Frame Buffer read access is not finished until a new frame is received, an
IRQ_6 (TRX_UR)
interrupt occurs. Nevertheless the old frame data can be
read, if the SPI data rate is higher than the effective PHY data rate. A minimum
SPI clock rate of 1MHz is recommended in this case. Finally, the microcontroller
should check the integrity of the transferred frame data by calculating the FCS.
3. When writing data to the Frame Buffer during frame transmission, the SPI data
rate shall be higher than the PHY data rate to ensure no under run interrupt.
The first byte of the PSDU data must be available in the Frame Buffer before
SFD transmission is complete, which takes 176µs (16µs PA ramp-up + 160µs
SHR) from the rising edge of pin 11 (SLP_TR) (see Figure 7-2).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
121
9.4 Voltage Regulators (AVREG, DVREG)
The main features of the Voltage Regulator blocks are:
• Bandgap stabilized 1.8V supply for analog and digital domain
• Low dropout (LDO) voltage regulator
• AVREG/DVREG can be disabled when an external regulated voltage is supplied to
AVDD/DVDD pin
9.4.1 Overview
The internal voltage regulators supply a stabilized voltage to the Atmel AT86RF233.
The AVREG provides the regulated 1.8V supply voltage for the analog section and the
DVREG supplies the 1.8V supply voltage for the digital section.
A simplified schematic of the internal voltage regulator is shown in Figure 9-9.
Figure 9-9. Simplified Schematic of AVREG.
Bandgap
voltage
reference
1.25 V
AVDD
EVDD
A simplified schematic of the internal digital voltage regulator is shown in Figure 9-10.
Figure 9-10. Simplified Schematic of DVREG
Bandgap
voltage
reference
1.25 V
DVDD
DEVDD
BIAS
Voltage regulator
Low power voltage regulator
Digital voltage regulator
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
122
The block “Low power voltage regulator” within the “Digital voltage regulator” maintains
the DVDD supply voltage at 1.5V (typical) when the Atmel AT86RF233 voltage
regulator is disabled in sleep mode. All configuration register values are stored.
The low power voltage regulator is always enabled. Therefore, its bias current
contributes to the leakage current in sleep mode with about 100nA (typical).
The voltage regulators (AVREG, DVREG) require bypass capacitors for stable
operation. The value of the bypass capacitors determine the settling time of the voltage
regulators. The bypass capacitors shall be placed as close as possible to the pins and
shall be connected to ground with the shortest possible traces (see Table 5-1).
9.4.2 Configuration
The voltage regulators can be configured by the register 0x10 (VREG_CTRL).
It is recommended to use the internal regulators, but it is also possible to supply the low
voltage domains by an external voltage supply. For this configuration, the internal
regulators need to be switched off by setting the register bits to the values
AVREG_EXT = 1 and DVREG_EXT = 1. A regulated external supply voltage of 1.8V
needs to be connected to the pins 13, 14 (DVDD) and pin 29 (AVDD). When providing
the external supply, ensure a sufficiently long stabilization time before interacting with
the AT86RF233.
9.4.3 Data Interpretation
The status bits AVDD_OK = 1 and DVDD_OK = 1 in register 0x10 (VREG_CTRL)
indicate an enabled and stable internal supply voltage. Reading value zero indicates a
disabled or internal supply voltage not settled to the final value. Setting
AVREG_EXT = 1 and DVREG_EXT = 1 forces the signals AVDD_OK and DVDD_OK
to one.
9.4.4 Register Description
Register 0x10 (VREG_CTRL):
The VREG_CTRL register controls the use of the voltage regulators and indicates the
status of these.
Figure 9-11. Register VREG_CTRL.
Bit
7
6
5
4
0x10 AVREG_EXT AVDD_OK reserved VREG_CTRL
Read/Write
R/W
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x10 DVREG_EXT DVDD_OK reserved VREG_CTRL
Read/Write
R/W
R
R
R
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
123
• Bit 7 - AVREG_EXT
If set this register bit disables the internal analog voltage regulator to apply an external
regulated 1.8V supply for the analog building blocks.
Table 9-11. AVREG_EXT.
Register Bits Value Description
AVREG_EXT 0 Internal voltage regulator enabled, analog section
1 Internal voltage regulator disabled, use external regulated
1.8V supply voltage for the analog section
• Bit 6 - AVDD_OK
This register bit indicates if the internal 1.8V regulated voltage supply AVDD has
settled. The bit is set to logic high, if AVREG_EXT = 1.
Table 9-12. AVDD_OK.
Register Bits Value Description
AVDD_OK 0 Analog voltage regulator is disabled or supply voltage not
stable
1 Analog supply voltage is stable
• Bit 3 - DVREG_EXT
If set this register bit disables the internal digital voltage regulator to apply an external
regulated 1.8V supply for the digital building blocks.
Table 9-13. DVREG_EXT.
Register Bits Value Description
DVREG_EXT 0 Internal voltage regulator enabled, digital section
1 Internal voltage regulator disabled, use external regulated
1.8V supply voltage for the digital section
• Bit 2 - DVDD_OK
This register bit indicates if the internal 1.8V regulated voltage supply DVDD has
settled. The bit is set to logic high, if DVREG_EXT = 1.
Table 9-14. DVDD_OK.
Register Bits Value Description
DVDD_OK 0 Digital voltage regulator is disabled or supply voltage not
stable
1 Digital supply voltage is stable
Note: 1.
While the reset value of this bit is zero, any practical access to the register is only
possible when DVREG is active. So this bit is normally always read out as one.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
124
9.5 Battery Monitor (BATMON)
The main features of the battery monitor are:
• Configurable voltage reference threshold from 1.70V to 3.675V
• Interrupt on low - supply voltage condition
• Continuous BATMON status monitor as a register flag
9.5.1 Overview
The Atmel AT86RF233 battery monitor (BATMON) detects and flags a low external
supply voltage level. provided on pin 28 (EVDD). The external voltage supply
pin 28 (EVDD) is continuosly compared with the internal threshold voltage to detect a
low voltage supply level. In this case BATMON_IRQ is triggered and BATMON_OK flag
is cleared to indicate undervoltage condition, see Figure 9-12.
Figure 9-12. Simplified Schematic of BATMON.
BATMON_HR
BATMON_VTH
4
EVDD
Threshold
Voltage
BATMON_OK
„1“
BATMON_IRQ
For input-to-output mapping
see control register
0x11 (BATMON)
DAC
+
-
D
Q
clear
9.5.2 Configuration
The BATMON can be configured using the register 0x11 (BATMON). Register bits
BATMON_VTH sets the threshold voltage. It is configurable with a resolution of 75mV
in the upper voltage range (BATMON_HR = 1) and with a resolution of 50mV in the
lower voltage range (BATMON_HR = 0), for details refer to register 0x11 (BATMON).
9.5.3 Data Interpretation
The signal register bit BATMON_OK of register 0x11 (BATMON) monitors the current
value of the battery voltage:
• If BATMON_OK = 0, the battery voltage is lower than the threshold voltage
• If BATMON_OK = 1, the battery voltage is higher than the threshold voltage
After setting a new threshold, the value BATMON_OK should be read out to verify the
current supply voltage value.
Note: 1. The battery monitor is inactive during P_ON, SLEEP, and DEEP_SLEEP states,
see register bits TRX_STATUS (register 0x01, TRX_STATUS).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
125
9.5.4 Interrupt Handling
A supply voltage drop below the configured threshold value is indicated by an interrupt
IRQ_7 (BAT_LOW), see Section 6.7.
Note: 1. The Atmel AT86RF233 IRQ_7 (BAT_LOW) i
nterrupt is issued only if
BATMON_OK changes from one to zero.
IRQ_7 (BAT_LOW) interrupt is not generated under following conditions:
• The battery voltage remained below 1.8V threshold value on power-on
(BATMON_OK was never one), or
• A new threshold is set, which is still above the current supply voltage (BATMON_OK
remains zero).
When the battery voltage is close to the programmed threshold voltage, noise or
temporary voltage drops may generate unwanted interrupts. To avoid this:
• Disable the IRQ_7 (BAT_LOW) in register 0x0E (IRQ_MASK) and treat the battery
as empty, or
• Set a lower threshold value.
9.5.5 Register Description
Register 0x11 (BATMON):
The BATMON register configures the battery monitor to compare the supply voltage at
pin 28 (EVDD) to the threshold. Additionally, the supply voltage status at pin 28 (EVDD)
can be read from register bit BATMON_OK according to the actual BATMON settings.
Figure 9-13. Register BATMON.
Bit 7 6 5 4
0x11
reserved
BATMON_OK
BATMON_HR
BATMON
Read/Write R R/W R R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x11
BATMON_VTH
BATMON
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 5 - BATMON_OK
The register bit BATMON_OK indicates the level of the external supply voltage with
respect to the programmed threshold BATMON_VTH.
Table 9-15. BATMON_OK.
Register Bits Value Description
BATMON_OK 0 The battery voltage is below the threshold
1 The battery voltage is above the threshold
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
126
• Bit 4 - BATMON_HR
The register bit BATMON_HR sets the range and resolution of the battery monitor.
Table 9-16. BATMON_HR.
Register Bits Value Description
BATMON_HR 0 Enables the low range, see BATMON_VTH
1 Enables the high range, see BATMON_VTH
• Bit 3:0 – BATMON_VTH
The threshold values for the battery monitor are set by register bits BATMON_VTH.
Table 9-17. Battery Monitor Threshold Voltages.
Value
BATMON_VTH
Voltage [V]
BATMON_HR = 1
Voltage [V]
BATMON_HR = 0
0x0 2.550 1.70
0x1 2.625 1.75
0x2 2.700 1.80
0x3 2.775 1.85
0x4 2.850 1.90
0x5 2.925 1.95
0x6 3.000 2.00
0x7 3.075 2.05
0x8 3.150 2.10
0x9 3.225 2.15
0xA 3.300 2.20
0xB 3.375 2.25
0xC 3.450 2.30
0xD 3.525 2.35
0xE 3.600 2.40
0xF 3.675 2.45
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
127
9.6 Crystal Oscillator (XOSC)
The main crystal oscillator features are:
• 16MHz amplitude controlled crystal oscillator
• 180µs typical settling time after leaving SLEEP state
• 330µs typical settling time after leaving DEEP_SLEEP state
• Configurable trimming capacitance array
• Configurable clock output (CLKM)
9.6.1 Overview
The crystal oscillator generates the reference frequency for the Atmel AT86RF233. All
other internally generated frequencies of the radio transceiver are derived from this
unique frequency. Therefore, the overall system performance is mainly determined by
the accuracy of crystal reference frequency. The external components of the crystal
oscillator should be selected carefully and the related board layout should be done with
caution (see Chapter 5).
The register 0x12 (XOSC_CTRL) provides access to the control signals of the
oscillator. Two operating modes are supported. It is recommended to use the integrated
oscillator setup as described in Figure 9-14. Alternatively, a reference frequency can be
fed to the internal circuitry by using an external clock reference as shown in Figure
9-15.
9.6.2 Integrated Oscillator Setup
Using the internal oscillator, the oscillation frequency depends on the load capacitance
between the crystal pin 26 (XTAL1) and pin 25 (XTAL2). The total load capacitance CL
must be equal to the specified load capacitance of the crystal itself. It consists of the
external capacitors CX and parasitic capacitances connected to the XTAL nodes.
Figure 9-14 shows all parasitic capacitances, such as PCB stray capacitances and the
pin input capacitance, summarized to CPAR.
Figure 9-14. Simplified XOSC Schematic with External Components.
CX CX
16MHz XTAL2
XTAL1
EVDD
CTRIM
CTRIM
CPAR
CPAR
AT86RF233
PCB
XTAL_TRIM[3:0]
EVDD
VDD
XTAL_TRIM[3:0]
Additional internal trimming capacitors CTRIM are available. Any value in the range from
0pF to 4.5pF with a 0.3pF resolution is selectable using XTAL_TRIM of register 0x12
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
128
(XOSC_CTRL). To calculate the total load capacitance, the following formula can be
used
CL[pF] = 0.5 x (CX[pF] + CTRIM[pF] + CPAR[pF]) .
The Atmel AT86RF233 trimming capacitors provide the possibility of reducing
frequency deviations caused by production process variations or by external
components tolerances. Note that the oscillation frequency can only be reduced by
increasing the trimming capacitance. The frequency deviation caused by one step of
CTRIM decreases with increasing crystal load capacitor values.
An amplitude control circuit is included to ensure stable operation under different
operating conditions and for different crystal types. Enabling the crystal oscillator in
P_ON state and after leaving SLEEP or DEEP_SLEEP state causes a slightly higher
current during the amplitude build-up phase to guarantee a short start-up time. At stable
operation, the current is reduced to the amount necessary for a robust operation. This
also keeps the drive level of the crystal low.
Generally, crystals with a higher load capacitance are less sensitive to parasitic pulling
effects caused by external component variations or by variations of board and circuit
parasitic. On the other hand, a larger crystal load capacitance results in a longer start-
up time and a higher steady state current consumption.
9.6.3 External Reference Frequency Setup
When using an external reference frequency, the signal must be connected to
pin 26 (XTAL1) as indicated in Figure 9-15 and the register bits XTAL_MODE
(register 0x12, XOSC_CTRL) need to be set to the external oscillator mode for power
saving reasons. The oscillation peak-to-peak amplitude shall be between 400mV and
1V. Pin 25 (XTAL2) should not be wired. It is possible, among other waveforms, to use
sine and square wave signals.
Note: 1. The quality of the external reference (that is phase noise) determines the
system performance.
Figure 9-15. Setup for Using an External Frequency Reference.
XTAL2
XTAL1
AT86RF233
PCB
16MHz
9.6.4 Master Clock Signal Output (CLKM)
The generated reference clock signal can be fed to a microcontroller using
pin 17 (CLKM). The internal 16MHz raw clock can be divided by an internal prescaler.
Thus, clock frequencies of 16MHz, 8MHz, 4MHz, 2MHz, 1MHz, 250kHz, or 62.5kHz
can be supplied by pin 17 (CLKM).
The CLKM frequency is configurable using register 0x03 (TRX_CTRL_0). There are two
possibilities to change the CLKM frequency. If CLKM_SHA_SEL = 0, changing the
register bits CLKM_CTRL (register 0x03, TRX_CTRL_0) immediately affects a glitch
free the CLKM clock rate change. Otherwise (CLKM_SHA_SEL = 1 and
CLKM_CTRL > 0 before changing the register bits CLKM_CTRL), the new clock rate is
supplied when leaving the SLEEP state the next time.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
129
To reduced power consumption and spurious emissions, it is recommended to turn off
the Atmel AT86RF233 CLKM clock when not in use.
Notes: 1. During reset procedure, see Section 7.1.2.9, register bits CLKM_CTRL
are shadowed. Although the clock setting of CLKM remains after reset,
a read access to register bits CLKM_CTRL delivers the reset value one.
For that reason it is recommended to write the previous configuration
(before reset) to register bits CLKM_CTRL (after reset) to align the
radio transceiver behavior and register configuration. Otherwise the
CLKM clock rate is set back to the reset value (1MHz) after the next
SLEEP cycle.
For example, if the CLKM clock rate is configured to 16MHz the CLKM
clock rate remains at 16MHz after a reset, however the register bits
CLKM_CTRL are set back to one. Since CLKM_SHA_SEL reset value
is one, the CLKM clock rate changes to 1MHz after the next SLEEP
cycle if the CLKM_CTRL setting is not updated.
2. After leaving the DEEP_SLEEP state CLKM starts with the default
1MHz master clock at pin 17 (CLKM) after the crystal oscillator has
stabilized.
9.6.5 Register Description
Register 0x03 (TRX_CTRL_0):
The TRX_CTRL_0 register controls the CLKM clock rate.
Figure 9-16. Register TRX_CTRL_0.
Bit 7 6 5 4
0x03 TOM_EN reserved PMU_EN PMU_IF_
INVERSE
TRX_CTRL_0
Read/Write R/W R R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x03
CLKM_SHA_SEL
CLKM_CTRL
TRX_CTRL_0
Read/Write R/W R/W R/W R/W
Reset value
1 0 0 1
• Bit 3 - CLKM_SHA_SEL
The register bit CLKM_SHA_SEL defines whether a new clock rate (defined by
CLKM_CTRL) is set immediately or gets effective after the next SLEEP cycle.
Table 9-18. CLKM_SHA_SEL.
Register Bits Value Description
CLKM_SHA_SEL 0 CLKM clock rate change appears immediately
1 CLKM clock rate change appears after SLEEP cycle
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
130
• Bit 2:0 - CLKM_CTRL
The register bits CLKM_CTRL set the clock rate of pin 17 (CLKM).
Table 9-19. CLKM_CTRL.
Register Bits Value Description
CLKM_CTRL 0 No clock at pin 17 (CLKM), pin set to logic low
1 1MHz
2 2MHz
3 4MHz
4 8MHz
5 16MHz
6 250kHz
7 62.5kHz (IEEE 802.15.4 symbol rate)
Note: 1.
If a clock rate is selected between 1MHz and 16MHz and pin SLP_TR is set to
logic high in state TRX_OFF, the TRX delivers additional 35 clock cycles before
entering state SLEEP or DEEP_SLEEP.
Register 0x12 (XOSC_CTRL):
The XOSC_CTRL register controls the operation of the crystal oscillator.
Figure 9-17. Register XOSC_CTRL.
Bit
7
6
5
4
0x12
XTAL_MODE
XOSC_CTRL
Read/Write
R/W
R/W
R/W
R/W
Reset value
1
1
1
1
Bit
3
2
1
0
0x12
XTAL_TRIM
XOSC_CTRL
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 7:4 - XTAL_MODE
The register bits XTAL_MODE sets the operating mode of the crystal oscillator.
Table 9-20. XTAL_MODE.
Register Bits Value Description
XTAL_MODE 0x5 Internal crystal oscillator disabled, use external reference
frequency
0xF Internal crystal oscillator enabled and XOSC voltage
regulator enabled
All other values are reserved
For normal operation the default value is set to XTAL_MODE = 0xF after reset. Using
an external clock source it is recommended to set XTAL_MODE = 0x5.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
131
• Bit 3:0 - XTAL_TRIM
The register bits XTAL_TRIM control internal capacitance arrays connected to pin 26
(XTAL1) and pin 25 (XTAL2).
Table 9-21. XTAL_TRIM.
Register Bits Value Description
XTAL_TRIM 0x0 A capacitance value in the range from 0pF to 4.5pF is
selectable with a resolution of 0.3pF.
Valid values are [0xF, 0xE, …, 0x0].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
132
9.7 Frequency Synthesizer (PLL)
The main PLL features are:
• Generate RX/TX frequencies for all IEEE 802.15.4 – 2.4GHz channels
• Generate RX/TX frequencies from 2322MHz to 2527MHz
• Autonomous calibration loops for stable operation within the operating range
• Two PLL-interrupts for status indication
• Fast PLL settling to support frequency hopping
9.7.1 Overview
The PLL generates the RF frequencies for the Atmel AT86RF233. During receive
operation the frequency synthesizer works as a local oscillator on the radio transceiver
receive frequency, during transmit operation the voltage-controlled oscillator (VCO) is
directly modulated to generate the RF transmit signal. The frequency synthesizer is
implemented as a fractional-N PLL.
Two calibration loops ensure correct PLL functionality within the specified operating
limits.
9.7.2 RF Channel Selection
The PLL is designed to support 16 channels in the 2.4GHz ISM band with channel
spacing of 5MHz according to IEEE 802.15.4. The center frequency of these channels
is defined as follows:
Fc[MHz] = 2405[MHz] + 5[MHz] x (k – 11), for k = 11, 12, ..., 26
where k is the channel number.
The channel k is selected by register bits CHANNEL (register 0x08, PHY_CC_CA).
Additionally, the PLL supports all frequencies from 2322MHz to 2527MHz with 500kHz
frequency spacing. The frequency is selected by register bits CC_BAND
(registers 0x14, CC_CTRL_1) and register bits CC_NUMBER (registers 0x13,
CC_CTRL_0).
Table 9-22 shows the settings of the register bits CC_BAND and CC_NUMBER.
Table 9-22. Frequency Bands and Numbers.
CC_BAND CC_NUMBER Description
0x0 Not used Channels according to IEEE 802.15.4; frequency selected
by register bits CHANNEL (register 0x08, PHY_CC_CCA)
0x1, … , 0x7 0x00 – 0xFF Reserved
0x8 0x00 – 0x1F Reserved
0x8 0x20 – 0xFF 2322MHz – 2433.5MHz
Fc[MHz] = 2306[MHz] + 0.5[MHz] x CC_NUMBER
0x9 0x00 – 0xBA 2434MHz – 2527MHz.
Fc[MHz] = 2434[MHz] + 0.5[MHz] x CC_NUMBER
0x9 0xBB – 0xFF Reserved
0xA, … , 0xF 0x00 – 0xFF Reserved
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
133
9.7.3 PLL Settling Time and Frequency Agility
When the PLL is enabled during state transition from TRX_OFF to PLL_ ON or RX_ON,
the settling time is typically tTR4 = 80µs, including settling of the analog voltage regulator
(AVREG) and PLL self calibration, refer to Table 7-2 and Figure 13-14. A lock of the
PLL is indicated with an interrupt IRQ_0 (PLL_LOCK).
Switching between 2.4GHz ISM band channels in PLL_ON or RX_ON states is typically
done within tPLL_SW = 11µs. This makes the radio transceiver highly suitable for
frequency hopping applications.
The PLL frequency in PLL_ON and receive states is 2MHz below the PLL frequency in
transmit states. When starting the transmit procedure, the PLL frequency is changed to
the transmit frequency within a period of tRX_TX = 16µs before really starting the
transmission. After the transmission, the PLL settles back to the receive frequency
within a period of tTX_RX = 32µs. This frequency step does not generate an interrupt
IRQ_0 (PLL_LOCK) or IRQ_1 (PLL_UNLOCK) within these periods.
9.7.4 Calibration Loops
Due to variation of temperature, supply voltage and part-to-part variations of the radio
transceiver the VCO characteristics may vary.
To ensure a stable operation, two automated control loops are implemented, center
frequency (CF) tuning and delay cell (DCU) calibration. Both calibration loops are
initiated automatically when the PLL is enabled during state transition from TRX_OFF to
PLL_ON or RX_ON state. Additionally, both calibration loops are initiated when the PLL
changes to a different frequency setting.
If the PLL operates for a long time on the same channel, for example more than five
minutes, or the operating temperature changes significantly, it is recommended to
initiate the calibration loops manually.
Both Atmel AT86RF233 calibration loops can be initiated manually by SPI command.
To start the calibration, the device should be in state PLL_ON. The center frequency
calibration can be initiated by setting PLL_CF_START = 1 (register 0x1A, PLL_CF).
The calibration loop is completed when the IRQ_0 (PLL_LOCK) occurs, if enabled. The
duration of the center frequency calibration loop depends on the difference between the
current CF value and the final CF value. During the calibration, the CF value is
incremented or decremented. Each step takes tPLL_CF = 8µs. The minimum time is 8µs;
the maximum time is 24µs. The recommended procedure to start the center frequency
calibration is to read the register 0x1A (PLL_CF), to set the PLL_CF_START register bit
to one, and to write the value back to the register.
The delay cell calibration can be initiated by setting the bit PLL_DCU_START of
register 0x1B (PLL_DCU) to one. The delay time of the programmable delay unit is
adjusted to the correct value. The calibration works as successive approximation and is
independent of the values in the register 0x1B (PLL_DCU). The duration of the
calibration is tPLL_DCU = 6µs.
During both calibration processes, no correct receive or transmit operation is possible.
The recommended state for the calibration is therefore PLL_ON, but calibration is not
blocked at receive or transmit states.
Both calibrations can be executed concurrently.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
134
9.7.5 Interrupt Handling
Two different interrupts indicate the PLL status (refer to register 0x0F).
IRQ_0 (PLL_LOCK) indicates that the PLL has locked. IRQ_1 (PLL_UNLOCK) interrupt
indicates an unexpected unlock condition. A PLL_LOCK interrupt clears any preceding
PLL_UNLOCK interrupt automatically and vice versa.
An IRQ_0 (PLL_LOCK) interrupt is supposed to occur in the following situations:
• State change from TRX_OFF to PLL_ON / RX_ON / TX_ARET_ON / RX_AACK_ON
• Frequency setting change in states PLL_ON / RX_ON / TX_ARET_ON /
RX_AACK_ON
• A manually started center frequency calibration has been completed
All other PLL_LOCK interrupt events indicate that the PLL locked again after a prior
unlock happened.
An IRQ_1 (PLL_UNLOCK) interrupt occurs in the following situations:
• A manually initiated center frequency calibration in states PLL_ON / (RX_ON)
• Frequency setting change in states PLL_ON / RX_ON
Any other occurrences of IRQ_1 (PLL_UNLOCK) indicate erroneous behavior and
require checking of the actual device status.
PLL_LOCK and PLL_UNLOCK affect the behavior of the transceiver:
In states BUSY_TX and BUSY_TX_ARET the transmission is stopped and the
transceiver returns into state PLL_ON. During BUSY_RX and BUSY_RX_AACK, the
transceiver returns to state RX_ON and RX_AACK_ON, respectively, once the PLL has
locked.
Notes: 1. An Atmel AT86RF233 interrupt IRQ_0 (PLL_LOCK)
clears any preceding
IRQ_1 (PLL_UNLOCK) interrupt automatically and vice versa.
2. The state transition from BUSY_TX / BUSY_TX_ARET to
PLL_ON / TX_ARET_ON after successful transmission does not generate an
IRQ_0 (PLL_LOCK) within the settling period.
9.7.6 Register Description
Register 0x08 (PHY_CC_CCA):
The PHY_CC_CCA register is a multi-purpose register that controls CCA configuration,
CCA measurement, and the IEEE 802.15.4 channel setting.
Figure 9-18. Register PHY_CC_CCA.
Bit 7 6 5 4
0x08
CCA_REQUEST
CCA_MODE
CHANNEL
PHY_CC_CCA
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x08
CHANNEL
PHY_CC_CCA
Read/Write R/W R/W R/W R/W
Reset value
1 0 1 1
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
135
• Bit 4:0 - CHANNEL
The register bits CHANNEL define the RX/TX channel. The channel assignment is
according to IEEE 802.15.4.
Table 9-23. CHANNEL.
Register Bits Value Description
CHANNEL 0x0B 2405MHz
0x0C 2410MHz
0x0D 2415MHz
0x0E 2420MHz
0x0F 2425MHz
0x10 2430MHz
0x11 2435MHz
0x12 2440MHz
0x13 2445MHz
0x14 2450MHz
0x15 2455MHz
0x16 2460MHz
0x17 2465MHz
0x18 2470MHz
0x19 2475MHz
0x1A 2480MHz
All other values are reserved
Register 0x13 (CC_CTRL_0):
The CC_CTRL_0 register controls the frequency selection, if the selection by
CHANNEL (register 0x08, PHY_CC_CCA) is not used.
Figure 9-19. Register CC_CTRL_0.
Bit
7
6
5
4
0x13
CC_NUMBER
CC_CTRL_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x13
CC_NUMBER
CC_CTRL_0
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
136
• Bit 7:0 - CC_NUMBER
Table 9-24. CC_NUMBER.
Register Bits Value Description
CC_NUMBER 0x00 Alternative frequency selection with 500kHz frequency
spacing
CC_BAND = 0x0: Not used
CC_BAND = 0x8: Valid values are [0xFF, 0xFE, …, 0x20]
CC_BAND = 0x9: Valid values are [0xBA, 0xB9, …, 0x00]
All other values are reserved
Register 0x14 (CC_CTRL_1):
The CC_CTRL_1 register controls the selection of the frequency bands.
Figure 9-20. Register CC_CTRL_1.
Bit
7
6
5
4
0x14
reserved
CC_CTRL_1
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x14
CC_BAND
CC_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 3:0 - CC_BAND
The register bits CC_BAND control the selection for IEEE 802.15.4 channel band and
additional frequencies bands.
Table 9-25. CC_BAND.
Register Bits Value Description
CC_BAND 0x0 The IEEE 802.15.4 channel within register bits CHANNEL
is selected
0x8 The frequency band 0x8 is selected
0x9 The frequency band 0x9 is selected
All other values are reserved
If the register bits CC_BAND and CC_NUMBER are used, the frequency mapping is
described in Table 9-22.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
137
Register 0x1A (PLL_CF):
The PLL_CF register controls the operation of the center frequency calibration loop.
Figure 9-21. Register PLL_CF.
Bit 7 6 5 4
0x1A
PLL_CF_START
reserved
PLL_CF
Read/Write R/W R/W R/W R/W
Reset value
0 1 0 1
Bit 3 2 1 0
0x1A
PLL_CF
PLL_CF
Read/Write R/W R/W R/W R/W
Reset value
0 1 1 1
• Bit 7 - PLL_CF_START
Manual start of center frequency calibration cycle.
Table 9-26. PLL_CF_START.
Register Bits Value Description
PLL_CF_START 0 Center frequency calibration cycle is finished
1 Initiates center frequency calibration cycle
PLL_CF_START = 1 initiates the center frequency calibration. The calibration cycle has
finished after tPLL_CF = 8µs (typ.). The register bit is cleared immediately after finishing
the calibration.
Register 0x1B (PLL_DCU):
The PLL_DCU register controls the operation of the delay cell calibration loop.
Figure 9-22. Register PLL_DCU.
Bit
7
6
5
4
0x1B PLL_DCU_START reserved PLL_DCU
Read/Write
R/W
R
R/W
R/W
Reset value
0
0
1
0
Bit
3
2
1
0
0x1B reserved PLL_DCU
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 7 - PLL_DCU_START
Manual start of delay cell calibration cycle.
Table 9-27. PLL_DCU_START.
Register Bits Value Description
PLL_DCU_START 0 Delay cell calibration cycle is finished
1 Initiates delay cell calibration cycle
PLL_DCU_START = 1 initiates the delay cell calibration. The calibration cycle has
finished after tPLL_DCU = 6µs. The register bit is cleared immediately after finishing the
calibration.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
138
Register 0x3D (TST_SDM):
Figure 9-23. Register TST_SDM.
Bit 7 6 5 4
0x3D
MOD_SEL
MOD
TX_RX
TX_RX_SEL
TST_SDM
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x3D
reserved
TST_SDM
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Note: 1.
The register bits can be read or written, the values will effect the device operation
only if the register bit PMU_EN (register 0x03, TRX_CTRL_0) is set, otherwise
reset values will be applied.
• Bit 7 - MOD_SEL
The register bit MOD_SEL controls the modulation data source mode.
Table 9-28. MOD_SEL.
Register Bits Value Description
MOD_SEL 0 Normal operation is selected
1 Manual control of modulation data source is selected.
Used setting from register bit MOD.
• Bit 6 - MOD
The register bit MOD controls the manual modulation signal setting.
Table 9-29. MOD.
Register Bits Value Description
MOD 0 Continuous 0 chips
1 Continuous 1 chips
• Bit 5 - TX_RX
The register bit TX_RX controls the TX and RX PLL frequency setting within manual
control mode.
Table 9-30. TX_RX.
Register Bits Value Description
TX_RX 0 RX PLL frequency is selected
1 TX PLL frequency is selected
• Bit 4 - TX_RX_SEL
The register bit TX_RX_SEL controls the PLL frequency control mode.
Table 9-31. TX_RX_SEL.
Register Bits Value Description
TX_RX_SEL 0 Normal operation is selected
1 Manual control of PLL TX/RX frequency mode is selected.
Used setting from register bit TX_RX.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
139
9.8 Automatic Filter Tuning (FTN)
9.8.1 Overview
The Atmel AT86RF233 FTN is incorporated to compensate device tolerances for
temperature, supply voltage variations as well as part-to-part variations of the radio
transceiver. The filter-tuning result is used to correct the analog baseband filter transfer
function and the PLL loop-filter time constant, refer to Chapter 4.
An FTN calibration cycle is initiated automatically when entering the TRX_OFF state
from the P_ON, SLEEP, DEEP_SLEEP, or RESET state.
Although receiver and transmitter are very robust against these variations, it is
recommended to initiate the FTN manually if the radio transceiver does not use the
SLEEP or DEEP_SLEEP states. If necessary, a calibration cycle is to be initiated in
states TRX_OFF, PLL_ON or RX_ON. This applies in particular for the High Data Rate
Modes with a much higher sensitivity against BPF transfer function variations. The
recommended calibration interval is five minutes or less, if the AT86RF233 operates
always in an active state (PLL_ON, TX_ARET_ON, RX_ON, and RX_AACK_ON).
9.8.2 Register Description
Register 0x18 (FTN_CTRL):
The FTN_CTRL register controls the operation of the filter tuning network calibration
loop.
Figure 9-24. Register FTN_CTRL.
Bit 7 6 5 4
0x18
FTN_START
reserved
FTNV
FTN_CTRL
Read/Write R/W R/W R/W R/W
Reset value
0 1 0 1
Bit 3 2 1 0
0x18
FTNV
FTN_CTRL
Read/Write R/W R/W R/W R/W
Reset value
1 0 0 0
• Bit 7 - FTN_START
Manual start of a filter calibration cycle.
Table 9-32. FTN_START.
Register Bits Value Description
FTN_START 0 Filter calibration is finished
1 Initiates filter calibration cycle
FTN_START = 1 initiates the filter tuning network calibration. When the calibration cycle
has finished after tFTN = 25µs (typ.). The register bit is cleared immediately after
finishing the calibration.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
140
• Bit 5:0 - FTNV
Filter tuning value used for internal calibration loops.
Table 9-33. FTNV.
Register Bits Value Description
FTNV 0x18 Register bits FTNV defines the filter tuning value.
Valid values are [0x3F, 0x3E, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
141
10 Radio Transceiver Usage
This section describes basic procedures to receive and transmit frames using the
Atmel AT86RF233. For a detailed programming description refer to reference [7].
10.1 Frame Receive Procedure
A frame reception comprises of two actions: The transceiver listens for, receives, and
demodulates the frame to the Frame Buffer and signals the reception to the
microcontroller. After or during that process, the microcontroller can read the available
frame data from the Frame Buffer via the SPI interface.
While being in state RX_ON or RX_AACK_ON, the radio transceiver searches for
incoming frames on the selected channel. Assuming the appropriate interrupts are
enabled, the detection of a frame is indicated by interrupt IRQ_2 (RX_START). When
the frame reception is completed, interrupt IRQ_3 (TRX_END) is issued.
Different Frame Buffer read access scenarios are recommended for:
• Non-time critical applications read access starts after IRQ_3 (TRX_END)
• Time-critical applications read access starts after IRQ_2 (RX_START)
For non-time-critical operations, it is recommended to wait for interrupt
IRQ_3 (TRX_END) before starting a Frame Buffer read access. Figure 10-1 illustrates
the frame receive procedure using IRQ_3 (TRX_END).
Figure 10-1. Transactions between AT86RF233 and Microcontroller during
Receive.
AT86RF233
Microcontroller
IRQ issued (IRQ_2)
Read IRQ status, pin 24 (IRQ) deasserted
IRQ issued (IRQ_3)
Read frame data (Frame Buffer access)
Read IRQ status, pin 24 (IRQ) deasserted
Critical protocol timing could require starting the Frame Buffer read access after
interrupt IRQ_2 (RX_START). The first byte of the frame data can be read 32µs after
the IRQ_2 (RX_START) interrupt. The microcontroller must ensure to read slower than
the frame is received. Otherwise a Frame Buffer under run occurs, IRQ_6 (TRX_UR) is
issued, and the frame data may be not valid. To avoid this, the Frame Buffer read
access can be controlled by using a Frame Buffer Empty indicator, refer to
Section 11.7.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
142
10.2 Frame Transmit Procedure
A frame transmission comprises of two actions, a write to Frame Buffer and the
transmission of its contents. Both actions can be run in parallel if required by critical
protocol timing.
Figure 10-2 illustrates the Atmel AT86RF233 frame transmit procedure, when writing
and transmitting the frame consecutively. After a Frame Buffer write access, the frame
transmission is initiated by asserting pin 11 (SLP_TR) or writing command TX_START
to register bits TRX_CMD (register 0x02, TRX_STATE). The transceiver must be either
in PLL_ON state for basic operating mode or TX_ARET_ON state for extended
operating mode. The completion of the transaction is indicated by interrupt
IRQ_3 (TRX_END).
Figure 10-2. Transaction between AT86RF233 and Microcontroller during
Transmit.
AT86RF233
Microcontroller
Write frame data (Frame Buffer access)
Write TRX_CMD = TX_START, or assert pin 11 (SLP_TR)
IRQ_3 (TRX_END) issued
Read IRQ_STATUS register, pin 24 (IRQ) deasserted
Alternatively for time critical applications when the frame start transmission time needs
to be minimized, a frame transmission task can be started first. Then it can be followed
by the Frame Buffer write access event (populating PSDU data). This way the data to
be transmitted is needs to be written in the transmit frame buffer as the transceiver
initializes and begins SHR transmission; refer to Figure 10-3.
By initiating a transmission, either by asserting pin 11 (SLP_TR) or writing a TX_START
command to register bits TRX_CMD (register 0x02, TRX_STATE), the radio transceiver
starts transmitting the SHR, which is internally generated.
This first phase requires 16µs for PLL settling and 160μs for SHR transmission. The
PHR must be available in the Frame Buffer before this time elapses. Furthermore the
SPI data rate must be higher than the PHY data rate selected by register bits
OQPSK_DATA_RATE (register 0x0C, TRX_CTRL_2) to ensure that no Frame Buffer
under run occurs, indicated by IRQ_6 (TRX_UR), refer to Section 11.3.
Figure 10-3. Time Optimized Frame Transmit Procedure.
IRQ_3 (TRX_END) issued
Write frame data (Frame Buffer access)
Write TRX_CMD = TX_START, or assert pin 11 (SLP_TR)
AT86RF233
Microcontroller
Read IRQ_STATUS register, pin 24 (IRQ) deasserted
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
143
11 AT86RF233 Extended Feature Set
11.1 Security Module (AES)
The security module (AES) features include:
• Hardware accelerated encryption and decryption
• Compatible with AES-128 standard (128-bit key and data block size)
• ECB (encryption/decryption) mode and CBC (encryption) mode support
• Stand-alone operation, independent of other blocks
11.1.1 Overview
The security module is based on an AES-128 core according to FIPS197 standard,
refer to [6]. The security module works independently of other building blocks of the
Atmel AT86RF233. Encryption and decryption can be performed in parallel with a frame
transmission or reception.
The control of the security block is implemented as an SRAM access to address space
0x82 to 0x94. A Fast SRAM access mode allows for simultaneous new data writes and
reads of processed data within the same SPI transfer. This access procedure is used to
reduce the turnaround time for ECB and CBC modes, see Section 11.1.5.
In addition, the security module contains another 128-bit register to store the initial key
used for security operations. This initial key is not modified by the security module.
11.1.2 Security Module Preparation
The use of the security module requires a configuration of the security engine before
starting a security operation. The following steps are required:
Table 11-1. AES Engine Configuration Steps.
Step Description Description Section
1 Key Setup Write encryption or decryption key to SRAM 11.1.3
2 AES mode Select AES mode: ECB or CBC
Select encryption or decryption
11.1.4.1
11.1.4.2
3 Write Data Write plaintext or cipher text to SRAM 11.1.5
4 Start operation Start AES operation
5 Read Data Read cipher text or plaintext from SRAM 11.1.5
Before starting any security operation, a key must be written to the security engine,
refer to Section 11.1.3. The key set up requires the configuration of the AES engine
KEY mode using register bits AES_MODE (SRAM address 0x83, AES_CTRL).
The following step selects the AES mode, either electronic code book (ECB) or cipher
block chaining (CBC). These modes are explained in more detail in Section 11.1.4.
Further, encryption or decryption must be selected with register bit AES_DIR (SRAM
address 0x83, AES_CTRL).
After this, the 128-bit plain text or cipher text data has to be provided to the AES
hardware engine. The data uses the SRAM address range 0x84 – 0x93.
An encryption or decryption is initiated with register bit AES_REQUEST = 1 (SRAM
address 0x83, that is AES_CTRL, or the mirrored version SRAM address 0x94, that is
AES_CTRL_MIRROR).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
144
The AES module control registers are only accessible using SRAM read and write
accesses on address space 0x82 to 0x94. Configuring the AES mode, providing the
data, and starting a decryption or encryption operation can be combined in a single
SRAM access.
Notes: 1. No additional register access is required to operate the security block.
2. Access to the security block is not possible while the radio transceiver is
in SLEEP, DEEP_SLEEP, or RESET state.
3. All configurations of the security module, the SRAM content, and keys
are reset during DEEP_SLEEP or RESET state.
4. A read or write access to register 0x83 (AES_CTRL) during AES
operation terminates the current processing.
11.1.3 Security Key Setup
The setup of the key is prepared by setting register bits AES_MODE = 1 (SRAM
address 0x83, AES_CTRL). Afterwards the 128-bit key must be written to SRAM
addresses 0x84 through 0x93 (registers AES_KEY). It is recommended to combine the
setting of control register 0x83 (AES_CTRL) and the 128-bit key transfer using only one
SRAM access starting from address 0x83.
The address space for the 128-bit key and 128-bit data is identical from programming
point of view. However, both use different pages which are selected by register bit
AES_MODE before storing the data.
A read access to registers AES_KEY (0x84 – 0x93) returns the last round key of the
preceding security operation. After an ECB encryption operation, this is the key that is
required for the corresponding ECB decryption operation. However, the initial AES key,
written to the security module in advance of an AES run, see step one in Table 11-1, is
not modified during the AES operation. This initial key is used for the next AES run
even it cannot be read from AES_KEY.
Note: 1. ECB decryption is not required for IEEE 802.15.4 or ZigBee security
processing. The Atmel AT86RF233 provides this functionality as an
additional feature.
11.1.4 Security Operation Modes
11.1.4.1 Electronic Code Book (ECB)
ECB is the basic operating mode of the security module. After setting up the initial AES
key, register bits AES_MODE = 0 (SRAM address 0x83, AES_CTRL) sets up ECB
mode. Register bit AES_DIR (SRAM address 0x83, AES_CTRL) selects the direction,
either encryption or decryption. The data to be processed has to be written to SRAM
addresses 0x84 through 0x93 (registers AES_STATE).
An example for a programming sequence is shown in Figure 11-1. This example
assumes a suitable key has been loaded before.
A security operation can be started within one SRAM access by appending the start
command AES_REQUEST = 1 (register 0x94, AES_CTRL_MIRROR) to the SPI
sequence. Register AES_CTRL_MIRROR is a mirrored version of register 0x83
(AES_CTRL).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
145
Figure 11-1. ECB Programming SPI Sequence – Encryption.
00000000
10000011
01000000
byte 1 (address)
byte 0 (cmd.) byte 18
…. 10000000
data_15[7:0]
byte 19 (AES cmd)
byte 2 (AES cmd)
data_0[7:0]
byte 3
ECB, encryption
0x83
SRAM write AES start
Summarizing, the following steps are required to perform a security operation using
only one Atmel AT86RF233 SPI access:
1. Configure SPI access a) SRAM write, refer to Section 6.3.3
b) Start address 0x83
2. Configure AES operation address 0x83: select ECB mode, direction
3. Write 128-bit data block addresses 0x84 – 0x93: either plain or ciphertext
4. Start AES operation address 0x94: start AES operation, ECB mode
This sequence is recommended because the security operation is configured and
started within one SPI transaction.
The ECB encryption operation is illustrated in Figure 11-2. Figure 11-3 shows the ECB
decryption mode, which is supported in a similar way.
Figure 11-2. ECB Mode – Encryption.
Block Cipher
Encryption
Encryption
Key
Plaintext
Ciphertext
Block Cipher
Encryption
Encryption
Key
Plaintext
Ciphertext
Figure 11-3. ECB Mode – Decryption.
Block Cipher
Decryption
Decryption
Key
Plaintext
Ciphertext
Block Cipher
Decryption
Decryption
Key
Plaintext
Ciphertext
When decrypting, due to the nature of AES algorithm, the initial key to be used is not
the same as the one used for encryption, but rather the last round key instead. This last
round key is the content of the key address space stored after running one full
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
146
encryption cycle, and must be saved for decryption. If the decryption key has not been
saved, it has to be recomputed by first running a dummy encryption (of an arbitrary
plaintext) using the original encryption key, then fetching the resulting round key from
the key memory, and writing it back into the key memory as the decryption key.
ECB decryption is not used by either IEEE 802.15.4 or ZigBee frame security. Both of
these standards do not directly encrypt the payload, but rather a nonce instead, and
protect the payload by applying an XOR operation between the resulting (AES-) cipher
text and the original payload. As the nonce is the same for encryption and decryption
only ECB encryption is required. Decryption is performed by XORing the received
cipher text with its own encryption result respectively, which results in the original
plaintext payload upon success.
11.1.4.2 Cipher Block Chaining (CBC)
In CBC mode, the result of a previous AES operation is XORed with the new incoming
vector, forming the new plaintext to encrypt, see Figure 11-4. This mode is used for the
computation of a cryptographic checksum (message integrity code, MIC).
Figure 11-4. CBC Mode – Encryption.
Block Cipher
Encryption
Encryption
Key
Ciphertext
Block Cipher
Encryption
Plaintext
Ciphertext
Plaintext Initialization Vector (IV)
Encryption
Key
ECB
mode
CBC
mode
After preparing the AES key and defining the AES operation direction using
Atmel AT86RF233 SRAM register bit AES_DIR, the data has to be provided to the AES
engine and the CBC operation can be started.
The first CBC run has to be configured as ECB to process the initial data (plaintext
XORed with an initialization vector provided by the microcontroller). All succeeding AES
runs are to be configured as CBC by setting register bits AES_MODE = 2
(register 0x83, AES_CTRL). Register bit AES_DIR (register 0x83, AES_CTRL) must be
set to AES_DIR = 0 to enable AES encryption. The data to be processed has to be
transferred to the SRAM starting with address 0x84 to 0x93 (register AES_STATE).
Setting register bit AES_REQUEST = 1 (register 0x94, AES_CTRL_MIRROR) as
described in Section 11.1.4 starts the first encryption within one SRAM access. This
causes the next 128 bits of plaintext data to be XORed with the previous cipher text
data, see Figure 11-4.
According to IEEE 802.15.4 the input for the very first CBC operation has to be
prepared by a XORing a plaintext with an initialization vector (IV). The value of the
initialization vector is zero. However, for non-compliant usage any other initialization
vector can be used. This operation has to be prepared by the microcontroller.
Note: 1. The IEEE 802.15.4-2006 standard MIC algorithm requires CBC mode
encryption only, as it implements a one-way hash function.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
147
11.1.5 Data Transfer – Fast SRAM Access
The ECB and CBC modules including the AES core are clocked with 16MHz. One AES
operation takes tAES = 23.4µs to execute, refer to Table 7-2. That means that the
processing of the data is usually faster than the transfer of the data via the SPI
interface.
To reduce the overall processing time the Atmel AT86RF233 provides a Fast SRAM
access for the address space 0x82 to 0x94.
Figure 11-5. Packet Structure – Fast SRAM Access Mode.
SRAM writeMOSI
PHY_STATUSMISO
byte 0 (cmd)
address 0x83
XX
<AES_CTRL>
XX
byte 1 (addr.) byte 2 (cfg)
P0[7:0]
XX
byte 3byte 4byte 18
<AES_CTRL>
(1)
byte 19 (start)
0x83 0x850x84 0x93 0x94Address
MOSI
MISO
AES access #0
Address
P0 P15...cmd add cfg start
xx xx...stat xx xx xx
0x83 0x94...
AES access #1
P0 P15...cmd add cfg start
xx C14...stat xx xx C15
0x83 0x94...
AES access #n+1
xx xx...cmd add cfg start
xx C14...stat xx xx C15
0x83 0x94...
P1 P14
xx xx
P1 P14
C0 C13
xx xx
C0 C13
...
...C0[7:0]
P1[7:0]
C14[7:0] C15[7:0]
P15[7:0]
AES run #0 AES run #n
...
Note: 1. Byte 19 is the mirrored version of register AES_CTRL on SRAM
address 0x94, see register description AES_CTRL_MIRROR for details.
In contrast to a standard SRAM access, refer to Section 6.3.3, the Fast SRAM access
allows writing and reading of data simultaneously during one SPI access for
consecutive AES operations (AES run).
For each byte P0 transferred to pin 22 (MOSI) for example in “AES access #1”, see
Figure 11-5 (lower part), the previous content of the respective AES register C0 is
clocked out at pin 20 (MISO) with an offset of one byte.
In the example shown in Figure 11-5 the initial plaintext P0 – P15 is written to the
SRAM within “AES access #0”. The last command on address 0x94
(AES_CTRL_MIRROR) starts the AES operation (“AES run #0”). In the next “AES
access #1” new plaintext data P0 – P15 is written to the SRAM for the second AES run,
in parallel the ciphertext C0 – C15 from the first AES run is clocked out at pin MISO. To
read the ciphertext from the last “AES run #(n)” one dummy “AES access #(n+1)” is
needed.
Note: 2. The SRAM write access always overwrites the previous processing
result.
The Fast SRAM access automatically applies to all write operations to SRAM
addresses 0x82 to 0x94.
11.1.6 Start of Security Operation and Status
A security operation is started within one Atmel AT86RF233 SRAM access by
appending the start command AES_REQUEST = 1 (register 0x94,
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
148
AES_CTRL_MIRROR) to the SPI sequence. Register AES_CTRL_MIRROR is a
mirrored version of register 0x83 (AES_CTRL).
The status of the security processing is indicated by register 0x82 (AES_STATUS).
After tAES = 24µs (max.) AES processing time register bit AES_DONE changes to one
(register 0x82, AES_STATUS) indicating that the security operation has finished.
11.1.7 SRAM Register Summary
The following registers are required to control the security module:
Table 11-2. SRAM Security Module Address Space Overview.
SRAM-Addr. Register Name Description
0x80 – 0x81 Reserved
0x82 AES_STATUS AES status
0x83 AES_CTRL Security module control, AES mode
0x84 – 0x93
AES_KEY
AES_STATE
Depends on AES_MODE setting:
AES_MODE = 1:
- Contains AES_KEY (key)
AES_MODE = 0 or 2:
- Contains AES_STATE (128 bit data block)
0x94 AES_CTRL_MIRROR Mirror of register 0x83 (AES_CTRL)
0x95 – 0xFF Reserved
These registers are only accessible using SRAM write and read accesses, for details
refer to Section 6.3.3.
Note: 1. The AES registers are reset when entering the DEEP_SLEEP state.
11.1.8 Register Description
Register 0x82 (AES_STATUS):
The read-only register AES_STATUS signals the status of the security module and
operation.
Figure 11-6. Register AES_STATUS.
Bit
7
6
5
4
0x82 AES_ER reserved AES_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x82 reserved AES_DONE AES_STATUS
Read/Write
R
R
R
R
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
149
• Bit 7 - AES_ER
This SRAM register bit indicates an error of the AES module. An error may occur for
instance after an access to SRAM register 0x83 (AES_CTRL) while an AES operation
is running or after reading less than 128-bits from SRAM register space 0x84 – 0x93
(AES_STATE).
Table 11-3. AES_ER.
Register Bits Value Description
AES_ER 0 No error of the AES module
1 AES module error
• Bit 0 - AES_DONE
The bit AES_DONE signals the status of AES operation.
Table 11-4. AES_DONE.
Register Bits Value Description
AES_DONE 0 AES operation has not been completed
1 AES operation has been completed
Register 0x83 (AES_CTRL):
The AES_CTRL register controls the operation of the security module.
Figure 11-7. Register AES_CTRL.
Bit 7 6 5 4
0x83
AES_REQUEST
AES_MODE
AES_CTRL
Read/Write W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x83
AES_DIR
reserved
AES_CTRL
Read/Write R/W R R R
Reset value
0 0 0 0
Notes: 1.
Do not access this register during AES operation to read the AES core status. A
read or write access during AES operation stops the actual processing.
2.
To read the AES status use register bit AES_DONE (register 0x82,
AES_STATUS).
• Bit 7 - AES_REQUEST
A write access with AES_REQUEST = 1 initiates the AES operation.
Table 11-5. AES_REQUEST.
Register Bits Value Description
AES_REQUEST 0 Security module, AES core idle
1 A write access starts the AES operation
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
150
• Bit 6:4 - AES_MODE
This register bit sets the AES operation mode.
Table 11-6. AES_MODE.
Register Bits Value Description
AES_MODE 0 ECB mode
1 KEY mode
2 CBC mode
All other values are reserved
• Bit 3 - AES_DIR
The register bit AES_DIR sets the AES operation direction, either encryption or
decryption.
Table 11-7. AES_DIR.
Register Bits Value Description
AES_DIR 0 AES encryption (ECB, CBC)
1 AES decryption (ECB)
Register 0x94 (AES_CTRL_MIRROR):
Register 0x94 is a mirrored version of register 0x83 (AES_CTRL), for details refer to
register 0x83 (AES_CTRL).
This register could be used to start a security operation within a single SRAM access by
appending it to the data stream and setting register bit AES_REQUEST = 1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
151
11.2 Random Number Generator
11.2.1 Overview
The Atmel AT86RF233 incorporates a two bit truly random number generator by
observation of noise. This random number can be used to:
• Generate random seeds for CSMA-CA algorithm see Section 7.2
• Generate random values for AES key generation see Section 11.1
Random numbers are stored in register bits RND_VALUE (register 0x06, PHY_RSSI).
The random number is updated every tRND = 1µs in Basic Operation Mode receive
states. The Random Number Generator does not work if the preamble detector is
disabled (RX_PDT_DIS = 1, refer to Section 9.1.4).
11.2.2 Register Description
Register 0x06 (PHY_RSSI):
The PHY_RSSI register is a multi-purpose register that indicates FCS validity, to
provide random numbers, and a RSSI value.
Figure 11-8. Register PHY_RSSI.
Bit 7 6 5 4
0x06
RX_CRC_VALID
RND_VALUE
RSSI
PHY_RSSI
Read/Write R R R R
Reset value
0 1 1 0
Bit 3 2 1 0
0x06
RSSI
PHY_RSSI
Read/Write R R R R
Reset value
0 0 0 0
• Bit 6:5 - RND_VALUE
The 2-bit random value can be retrieved by reading register bits RND_VALUE.
Table 11-8. RND_VALUE.
Register Bits Value Description
RND_VALUE 3 Deliver two bit noise value within receive state.
Valid values are [3, 2, …, 0].
Note: 1. The radio transceiver shall be in Basic Operating Mode receive state.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
152
11.3 High Data Rate Modes
The main features are:
• High Data Rate Transmission up to 2000kb/s.
• Support of Basic and Extended Operating Mode
• Support of other features of the Extended Feature Set
11.3.1 Overview
The Atmel AT86RF233 also supports alternative data rates, higher than 250kb/s for
applications beyond IEEE 802.15.4 compliant networks.
The selection of a data rate does not affect the remaining functionality. Thus it is
possible to run all features and operating modes of the radio transceiver in various
combinations.
The data rate can be selected by writing to register bits OQPSK_DATA_RATE
(register 0x0C, TRX_CTRL_2).
The High Data Rate Modes occupy the same RF channel bandwidth as the
IEEE 802.15.4 – 2.4GHz 250kb/s standard mode. Due to the decreased spreading
factor, the sensitivity of the receiver is reduced accordingly. Table 11-9 shows typical
values of the sensitivity for different data rates.
Table 11-9. High Data Rate Sensitivity for AWGN channel.
High Data Rate Sensitivity Comment
250kb/s -101dBm PER ≤ 1%, PSDU length of 20 octets
500kb/s -96dBm PER ≤ 1%, PSDU length of 20 octets
1000kb/s -94dBm PER ≤ 1%, PSDU length of 20 octets
2000kb/s -88dBm PER ≤ 1%, PSDU length of 20 octets
By default there is no header based signaling of the data rate within a transmitted
frame. Thus nodes using a data rate other than the default IEEE 802.15.4 data rate of
250kb/s are to be configured in advance and consistently. Alternatively, the
configurable start of frame delimiter (SFD) could be used as an indicator of the PHY
data rate, see Section 11.9.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
153
11.3.2 High Data Rate Packet Structure
In order to allow appropriate frame synchronization, Atmel AT86RF233 higher data rate
modulation is restricted to the payload octets only. The SHR and the PHR field are
transmitted with the IEEE 802.15.4 compliant data rate of 250kb/s, refer to
Section 8.1.1.
A comparison of the general packet structure for different data rates with an example
PSDU length of 80 octets is shown in Figure 11-9.
Figure 11-9. High Data Rate Frame Structure.
250 kb/s
0time [µs]192
SFD
PHR
832 1472 2752
500 kb/s
SFD
PHR
1000 kb/s
SFD
PHR
2000 kb/s
SFD
PHR
512
FCS
FCS
PSDU: 80 octets
PSDU: 80 octets
PSDU: 80 octets
PSDU: 80 octets
Due to the overhead caused by the SHR, PHR as well as the FCS, the effective data
rate is lower than the selected data rate. This is also affected by the length of the
PSDU. A graphical representation of the effective PSDU data rate is shown in Figure
11-10.
Figure 11-10. Effective Data Rate “B” for O-QPSK High Data Rate Modes.
0
200
400
600
800
1000
1200
1400
1600
0 20 40 60 80 100 120
PSDU length in octets
B [kb/s]
2000
1000
500
250
2000 kb/s
1000 kb/s
500 kb/s
250 kb/s
The effective throughput is further affected by the MAC overhead, the acknowledgment
scheme as well as the microcontroller processing capability. Consequently, High Data
Rate transmission and reception is useful for large PSDU lengths due to the higher
effective data rate, or to reduce the power consumption of the system. When using High
Data Rate Modes the active on-air time is significantly reduced.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
154
11.3.3 High Data Rate Frame Buffer Access
The Atmel AT86RF233 Frame Buffer access to read or write frames for High Data Rate
transmission is similar to the procedure described in Section 6.3.2. However, during
Frame Buffer read access the next byte transferred after the PSDU data is the LQI
value. This value is invalid for the High Data Rates.
Figure 11-11 illustrates the packet structure of a High Data Rate Frame Buffer read
access.
Figure 11-11. Packet Structure - High Data Rate Frame Buffer Read Access.
0reserved[4:0]
0MOSI
PHY_STATUSMISO
byte 1 (command byte)
1XX
PHR[7:0]
byte 2 (data byte)
XX
PSDU[7:0]
byte 3 (data byte)
XX
ED[7:0]
byte n-1 (data byte)
XX
RX_STATUS[7:0]
byte n (data byte)
The structure of RX_STATUS is described in Table 6-3.
11.3.4 High Data Rate Energy Detection
According to IEEE 802.15.4 the ED measurement duration is eight symbol periods. For
frames operated at higher data rates the automated ED measurement duration is
reduced to 32µs to take the reduced frame length into account, refer to Section 8.5.
During Frame Buffer read access the ED value is appended to the PSDU data, refer to
Section 11.3.3.
11.3.5 High Data Rate Mode Options
Receiver Sensitivity Control
The different data rates between PPDU header (SHR and PHR) and PHY payload
(PSDU) cause a different sensitivity between header and payload. This can be adjusted
by defining sensitivity threshold levels of the receiver. With a sensitivity threshold level
RX_PDT_LEVEL > 0 (register 0x15, RX_SYN), the receiver does not receive frames
with an RSSI level below that threshold. Under these operating conditions the receiver
current consumption is reduced to 11.3mA, refer to Section 12.8 parameter IRX_ON_L0.
Enabling receiver sensitivity control with at least RX_PDT_LEVEL = 1 is recommended
for the 2000kb/s rate with a PSDU sensitivity of -88dBm. In the case of receiving with
the default setting of RX_PDT_LEVEL, a high data rate frame may be detected even if
the PSDU sensitivity is above the received signal strength. In this case the frame is
rejected.
A description of the settings to control the sensitivity threshold RX_PDT_LEVEL
(register 0x15, RX_SYN) can be found in Section 9.1.4.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
155
Scrambler
For data rate 2000kb/s, additional chip scrambling is applied per default, in order to
mitigate data dependent spectral properties. Scrambling can be disabled if
Atmel AT86RF233 register bit OQPSK_SCRAM_EN (register 0x0C, TRX_CTRL_2) is
set to zero.
Carrier Sense
For clear channel assessment, IEEE 802.15.4-2006 specifies several modes which may
either apply Energy above threshold or Carrier sense (CS) or a combination of both. In
High Data Rate Modes only “Energy above threshold” is supported, since the
modulation spreading is not compliant to IEEE 802.15.4-2006.
Link Quality Indicator (LQI)
For the High Data Rate Modes, the link quality indicator does not contain useful
information and should be discarded.
Reduced Acknowledgment Timing
On higher data rates the IEEE 802.15.4 compliant acknowledgment frame response
time of 192µs significantly reduces the effective data rate of the network. To minimize
this influence in Extended Operating Mode RX_AACK, refer to Section 7.2.3, the
acknowledgment frame response time can be reduced to 32µs. Figure 11-12 illustrates
an example for a reception and acknowledgement of a frame with a data rate of
2000kb/s and a PSDU length of 80 symbols. The PSDU length of the acknowledgment
frame is five octets according to IEEE 802.15.4.
Figure 11-12. High Data Rate AACK Timing.
0time [µs]
192 512
AACK_ACK_TIME = 0 PSDU: 80 octets
SFD
PHR
SFD
PHR
704 916
32 µs
PSDU: 80 octets
SFD
PHR
SFD
PHR
192 µs
544
AACK_ACK_TIME = 1
ACK
ACK
If register bit AACK_ACK_TIME (register 0x17, XAH_CTRL_1) is set the
acknowledgment time is reduced from 192µs to 32µs.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
156
11.3.6 Register Description
Register 0x0C (TRX_CTRL_2):
The TRX_CTRL_2 register is a multi-purpose control register to control various settings
of the radio transceiver.
Figure 11-13. Register TRX_CTRL_2.
Bit 7 6 5 4
0x0C RX_SAFE_MODE reserved OQPSK_SCRAM_
EN
reserved TRX_CTRL_2
Read/Write R/W R R/W R
Reset value
0 0 1 0
Bit 3 2 1 0
0x0C
reserved
OQPSK_DATA_RATE
TRX_CTRL_2
Read/Write R R/W R/W R/W
Reset value
0 0 0 0
• Bit 5 - OQPSK_SCRAM_EN
If register bit OQPSK_SCRAM_EN is enabled, an additional chip scrambling is applied
for 2000kb/s data rate.
Table 11-10. OQPSK_SCRAM_EN.
Register Bits Value Description
OQPSK_SCRAM_EN 0 Scrambler is disabled
1 Scrambler is enabled
• Bit 2:0 - OQPSK_DATA_RATE
A write access to these register bits set the OQPSK PSDU data rate used by the radio
transceiver. The reset value O-QPSK_DATA_RATE = 0 is the PSDU data rate
according to IEEE 802.15.4.
Table 11-11. OQPSK_DATA_RATE.
Register Bits Value Description
OQPSK_DATA_RATE 0(1) 250kb/s
1 500kb/s
2 1000kb/s
3 2000kb/s
All other values are reserved
Note: 1. IEEE 802.15.4 compliant.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
157
Register 0x15 (RX_SYN):
The register RX_SYN controls the blocking of receiver path and the sensitivity threshold
of the receiver.
Figure 11-14. Register RX_SYN.
Bit 7 6 5 4
0x15
RX_PDT_DIS
reserved
RX_SYN
Read/Write R/W R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x15
RX_PDT_LEVEL
RX_SYN
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
• Bit 3:0 - RX_PDT_LEVEL
The register bits RX_PDT_LEVEL desensitize the receiver in steps of 3dB.
Table 11-12. RX_PDT_LEVEL.
Register Bits Value Description
RX_PDT_LEVEL 0x00 Maximum RX sensitivity
0x0F RX input level > RSSI_BASE_VAL + 3[dB] x 14
Register 0x17 (XAH_CTRL_1):
The XAH_CTRL_1 register is a multi-purpose controls register for Extended Operating
Mode.
Figure 11-15. Register XAH_CTRL_1.
Bit
7
6
5
4
0x17 ARET_TX_TS_EN reserved AACK_FLTR_RES_
FT
AACK_UPLD_RES_
FT XAH_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x17 reserved AACK_ACK_TIME AACK_PROM_
MODE AACK_SPC_EN XAH_CTRL_1
Read/Write
R
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 2 - AACK_ACK_TIME
The register bit AACK_ACK_TIME controls the acknowledgment frame response time
within RX_AACK mode.
Table 11-13. AACK_ACK_TIME.
Register Bits Value Description
AACK_ACK_TIME 0 Acknowledgment time is 12 symbol periods
(aTurnaroundTime)
1 Acknowledgment time is two symbol periods
According to IEEE 802.15.4-2006, Section 7.5.6.4.2 the transmission of an
acknowledgment frame shall commence 12 symbol periods (aTurnaroundTime) after
the reception of the last symbol of a data or MAC command frame. This is achieved
with the reset value of the register bit AACK_ACK_TIME.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
158
Alternatively, if AACK_ACK_TIME = 1 an acknowledgment frame is sent already two
symbol periods after the reception of the last symbol of a data or MAC command frame.
This may be applied to proprietary networks or networks using the High Data Rate
Modes to increase battery lifetime and to improve the overall data throughput.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
159
11.4 Antenna Diversity
The Antenna Diversity implementation is characterized by:
• Improves signal path robustness between nodes
• Atmel AT86RF233 self-contained antenna diversity algorithm
• Direct register based antenna selection
11.4.1 Overview
Due to multipath propagation effects between network nodes, the receive signal
strength may vary and affect the link quality, even for small variance of the antenna
location. These fading effects can result in an increased error floor or loss of the
connection between devices.
To improve the reliability of an RF connection between network nodes Antenna
Diversity can be applied to reduce effects of multipath propagation and fading. Antenna
Diversity uses two antennas to select the most reliable RF signal path. To ensure highly
independent receive signals on both antennas, the antennas should be carefully
separated from each other.
If a valid IEEE 802.15.4 frame is detected on one antenna, this antenna is selected for
reception. Otherwise the search is continued on the other antenna and vice versa.
Antenna Diversity can be used in Basic and Extended Operating Modes and can also
be combined with other features and operating modes like High Data Rate Mode and
RX/TX Indication.
11.4.2 Antenna Diversity Application Example
A block diagram for an application using an antenna switch is shown in Figure 11-16.
Figure 11-16. Antenna Diversity – Block Diagram.
6
5
4
3
2
1
910
AT86RF233
DIG3
DIG4
AVSS
RFP
RFN
AVSS
DIG1
DIG2
Balun
ANT0
ANT1
RF-
Switch
B1SW1
...
Generally, when the external RF-Switch (SW1) is to be controlled by antenna diversity
algorithm, the antenna diversity enable must be activated by register bit
ANT_EXT_SW_EN (register 0x0D, ANT_DIV). Then the digital control pins pin 9 (DIG1)
and pin 10 (DIG2) are enabled (refer to Section 1.3) to drive the antenna switch control
signals to the differential inputs of the RF Switch (SW1) to switch between ANT0 and
ANT1.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
160
If the Atmel AT86RF233 is not in a receive or transmit state, it is recommended to
disable register bit ANT_EXT_SW_EN to reduce the power consumption or avoid
leakage current of an external RF switch, especially during SLEEP or DEEP_SLEEP
state. If register bit ANT_EXT_SW_EN = 0, output pins DIG1/DIG2 are pulled-down to
digital ground.
User Defined Antenna Selection
A microcontroller defined selection of a certain antenna can be done by disabling the
automated Antenna Diversity algorithm (ANT_DIV_EN = 0) and selecting one antenna
using register bits ANT_CTRL = 1 / 2.
The antenna defined by register bits ANT_CTRL (register 0x0D, ANT_DIV) is used for
transmission and reception.
Autonomous Antenna Selection
The autonomous Antenna Diversity algorithm is enabled with register bits
ANT_DIV_EN = 1 and ANT_CTRL = 0 / 3 (register 0x0D, ANT_DIV). It allows the use of
Antenna Diversity even if the microcontroller does currently not control the radio
transceiver, for instance in Extended Operating Mode.
Upon reception of a frame, the AT86RF233 selects one antenna. The selected antenna
is then indicated by register bit ANT_SEL (register 0x0D, ANT_DIV). If required, it is
recommended to read register bit ANT_SEL after IRQ_2 (RX_START). After the frame
reception is completed, the antenna selection continues searching for new frames on
both antennas. However, the register bit ANT_SEL maintains its previous value (from
the last received frame) until a new IEEE 802.15.4 frame has been detected, and the
selection algorithm locked into one antenna again. At this time the register bit ANT_SEL
is updated again.
If a device is in RX_AACK mode, receiving a frame containing an ACK request, the
ACK frame is transmitted using the same antenna as used during receive.
If a device performs a transaction in TX_ARET mode, it starts to listen for an ACK on
the transmit antenna. If no ACK was received, the next transmission attempt is done on
the other transmit antenna. This will be repeated with each retry.
11.4.3 Antenna Diversity Sensitivity Control
Due to a different receive algorithm used by the Antenna Diversity algorithm, the
correlator threshold of the receiver has to be adjusted. It is recommended to set register
bits PDT_THRES (register 0x0A, RX_CTRL) to three.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
161
11.4.4 Register Description
Register 0x0A (RX_CTRL):
The RX_CTRL register controls the sensitivity of the Antenna Diversity mode and
indicates the receiver synchronization behavior.
Figure 11-17. Register RX_CTRL.
Bit 7 6 5 4
0x0A
PEL_SHIFT_VALUE
reserved
RX_CTRL
Read/Write R R R/W R/W
Reset value
0 0 1 1
Bit 3 2 1 0
0x0A
PDT_THRES
RX_CTRL
Read/Write R/W R/W R/W R/W
Reset value
0 1 1 1
• Bit 3:0 - PDT_THRES
The register bits PDT_THRES control the sensitivity of the receiver correlation unit.
Table 11-14. PDT_THRES.
Register Bits Value Description
PDT_THRES 0x3(1) Recommended correlator threshold for Antenna Diversity
operation
0x7 To be used if Antenna Diversity algorithm is disabled
All other values are reserved
Note: 1.
If the Antenna Diversity algorithm is enabled (ANT_DIV_EN = 1), the value shall
be set to PDT_THRES = 3, otherwise it shall be set back to the reset value. This is
not automatically done by the hardware.
Register 0x0D (ANT_DIV):
The ANT_DIV register controls Antenna Diversity.
Figure 11-18. Register ANT_DIV.
Bit
7
6
5
4
0x0D ANT_SEL reserved ANT_DIV
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x0D ANT_DIV_EN ANT_EXT_SW_EN ANT_CTRL ANT_DIV
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
162
• Bit 7 - ANT_SEL
Signals selected antenna, related to the last received frame.
Table 11-15. ANT_SEL.
Register Bits Value Description
ANT_SEL 0 Antenna 0
1 Antenna 1
Note: 1.
If the autonomous Antenna Diversity algorithm is enabled, the register bit
ANT_SEL maintains its previous value (from the last received frame) until a new
SHR has been found.
This register bit signals the currently selected antenna path. The selection may be
based either on the last antenna diversity cycle (ANT_DIV_EN = 1) or on the content of
register bits ANT_CTRL, for details refer to Section 11.4.2.
• Bit 3 - ANT_DIV_EN
The register bit ANT_DIV_EN activates the autonomous Antenna Diversity algorithm.
Table 11-16. ANT_DIV_EN.
Register Bits Value Description
ANT_DIV_EN 0 Antenna Diversity algorithm is disabled
1 Antenna Diversity algorithm is enabled
Note: 1.
If ANT_DIV_EN = 1 register bit ANT_EXT_SW_EN shall be set to one, too. This is
not automatically done by the hardware.
If register bit ANT_DIV_EN is set the Antenna Diversity algorithm is enabled. On
reception of a frame the algorithm selects an antenna autonomously during SHR
search. This selection is kept until:
• A new SHR search starts
• Leaving receive states
• Register bits ANT_CTRL are manually programmed
• Bit 2 - ANT_EXT_SW_EN
The register bit ANT_EXT_SW_EN controls the external antenna switch.
Table 11-17. ANT_EXT_SW_EN.
Register Bits Value Description
ANT_EXT_SW_EN 0 Antenna Diversity RF switch control is disabled
1 Antenna Diversity RF switch control is enabled
If enabled, pin 9 (DIG1) and pin 10 (DIG2) become output pins and provide a differential
control signal for an Antenna Diversity switch. The selection of a specific antenna is
done either by the automated Antenna Diversity algorithm (ANT_DIV_EN = 1), or
according to register bits ANT_CTRL if Antenna Diversity algorithm is disabled.
If the Atmel AT86RF233 is not in receive or transmit state, it is recommended to disable
register bit ANT_EXT_SW_EN to reduce the power consumption or avoid leakage
current of an external RF switch, especially during SLEEP or DEEP_SLEEP state. If
register bit ANT_EXT_SW_EN = 0, output pins DIG1 and DIG2 are pulled-down to
digital ground.
Pin 10 (DIG2) is overloaded with RX and TX Frame Time Stamping, see Section 11.6, if
IRQ_2_EXT_EN is set.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
163
• Bit 1:0 - ANT_CTRL
These register bits provide a static control of an Antenna Diversity switch.
Table 11-18. ANT_CTRL.
Register Bits Value Description
ANT_CTRL 0 Mandatory setting for applications not using Antenna
Diversity and if autonomous antenna selection is enabled
1 Antenna 0
DIG1 = L
DIG2 = H
2 Antenna 1
DIG1 = H
DIG2 = L
3 Same behavior as value zero
These register bits provide a static control of an Antenna Diversity switch if
ANT_DIV_EN = 0 and ANT_EXT_SW_EN = 1. Although it is possible to change
register bits ANT_CTRL in state TRX_OFF, this change will be effective at pin 9 (DIG1)
and pin 10 (DIG2) in states PLL_ON and RX_ON.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
164
11.5 RX/TX Indicator
The main features are:
• RX/TX indicator to control an external RF front-end
• Microcontroller independent RF front-end control
• Providing TX timing information
11.5.1 Overview
While IEEE 802.15.4 is targeting low cost and low power applications, solutions
supporting higher transmit output power are occasionally desirable. To simplify the
control of an optional external RF front-end, a differential control pin pair can indicate
that the Atmel AT86RF233 is currently in transmit mode.
The control of an external RF front-end is done via digital control pins DIG3/DIG4. The
function of this pin pair is enabled with register bit PA_EXT_EN (register 0x04,
TRX_CTRL_1). While the transmitter is turned off, pin 1 (DIG3) is set to low level and
pin 2 (DIG4) to high level. If the radio transceiver starts to transmit, the two pins change
the polarity. This differential pin pair can be used to control PA, LNA, and RF switches.
If the AT86RF233 is not in a receive or transmit state, it is recommended to disable
register bit PA_EXT_EN (register 0x04, TRX_CTRL_1) to reduce the power
consumption or avoid leakage current of external RF switches and other building
blocks, especially during SLEEP or DEEP_SLEEP state. If register bit PA_EXT_EN = 0,
output pins DIG3/DIG4 are pulled-down to analog ground.
11.5.2 External RF-Front End Control
The timing of an external RF front-end relative to the radio transceiver sequencing is
shown in Figure 11-19 and Figure 11-20, focusing on the TX indication.
A rising edge of pin 11 (SLP_TR) initiates a transmission, refer to Section 9.1. The radio
transceiver control switches the differential pin pair DIG3/DIG4 6µs after TX request
recognition to TX operating mode indication. After finishing the transmission, as shown
in Figure 11-20, pin pair DIG3/DIG4 is switched back to RX operating mode indication
3µs after disabling the AT86RF233 internal PA.
Figure 11-19. TX Power Up Ramping Control for RF Front-Ends for maximum TX Power.
06 8 10
TRX_STATE
SLP_TR
PLL_ON
212 14 16 18 Length [μs]
PA buffer
4
PA
DIG3
DIG4
Modulation 1 1 0 0 0 00 01
BUSY_TX
1 0 0 1 0 10 110 1 1 0 1 01 00
0 1
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
165
Figure 11-20. TX Power Down Ramping for maximum TX Power.
06
TRX_STATE BUSY_TX
2Length [μs]
PA buffer
4
PA
DIG3
DIG4
Modulation 1 1 0 0 01
PLL_ON
0 1 1 0 1 01 00
1
11.5.3 Register Description
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 11-21. Register TRX_CTRL_1.
Bit 7 6 5 4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0
0
1
0
Bit 3 2 1 0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 7 – PA_EXT_EN
The register bit PA_EXT_EN enables pin 1 (DIG3) and pin 2 (DIG4) to indicate the
transmit state of the radio transceiver.
Table 11-19. RF Front-End Control Pins.
PA_EXT_EN State Pin Value Description
0 n/a DIG3 L External RF front-end control disabled
DIG4 L
1(1) TX_BUSY DIG3 H External RF front-end control enabled
DIG4 L
Other DIG3 L
DIG4 H
Note: 1. It is recommended to set PA_EXT_EN = 1 only in receive or transmit states to
reduce the power consumption or avoid leakage current of external RF switches or
other building blocks, especially during SLEEP or DEEP_SLEEP state.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
166
11.6 RX and TX Frame Time Stamping (TX_ARET)
11.6.1 Overview
An exact timing of received and transmitted frames is signaled by Atmel AT86RF233
pin 10 (DIG2). A valid PHR reception or start of frame transmission is indicated by a
DIG2 rising edge. The pin remains high during frame reception or transmission. TX
Frame Time Stamping is limited to TX_ARET, whereas the RX Frame Time Stamping is
available for all receive modes. Exemplary, Figure 11-22 illustrates a frame reception
example.
If this pin is not used for RX Frame Time Stamping, it can be configured for Antenna
Diversity, refer to Section 11.4. Otherwise, this pin is internally connected to ground.
Figure 11-22. Timing of RX_START and DIG2 for RX Frame Time Stamping.
128 160 1920 192 + m * 32 Time [µs]
RX Frame
on Air
IRQ_2 (RX_START)
tIRQ
RX_ON RX_ON
IRQ
TRX_STATE
Interrupt latency
Preamble SFD PHR PSDU (250 kb/s)
4 1 1 m < 128
Number of Octets
Frame Content
TRX_END
tIRQ
BUSY_RX
DIG2 (RX Frame Time Stamp)
Note: 1. Timing figures tIRQ refer to Section 12.4.
11.6.2 Register Description
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 11-23. Register TRX_CTRL_1.
Bit
7
6
5
4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
1
0
Bit
3
2
1
0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
1
0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
167
• Bit 6 - IRQ_2_EXT_EN
The register bit IRQ_2_EXT_EN controls external signaling for time stamping via pin 10
(DIG2).
Table 11-20. IRQ_2_EXT_EN.
Register Bits Value Description
IRQ_2_EXT_EN 0 Time stamping over pin 10 (DIG2) is disabled
1(1) Time stamping over pin 10 (DIG2) is enabled
Notes: 1.
The pin 10 (DIG2) is also active if the corresponding interrupt event IRQ_2
(RX_START) mask bit in register 0x0E (IRQ_MASK) is set to zero.
2.
The pin remains at high level until the end of the frame receive or transmit
procedure.
Register 0x17 (XAH_CTRL_1):
The XAH_CTRL_1 register is a multi-purpose controls register for Extended Operating
Mode.
Figure 11-24. Register XAH_CTRL_1.
Bit
7
6
5
4
0x17 ARET_TX_TS_EN reserved AACK_FLTR_RES_
FT
AACK_UPLD_RES_
FT
XAH_CTRL_1
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x17 reserved AACK_ACK_TIME AACK_PROM_
MODE
AACK_SPC_EN XAH_CTRL_1
Read/Write
R
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 7 - ARET_TX_TS_EN
If register bit ARET_TX_TS_EN = 1, then any frame transmission within TX_ARET
mode is signaled via pin 10 (DIG2).
Table 11-21. ARET_TX_TS_EN.
Register Bits Value Description
ARET_TX_TS_EN 0 TX_ARET time stamping via pin 10 (DIG2) is disabled
1(1) TX_ARET time stamping via pin 10 (DIG2) is enabled
Note: 1. It is necessary to set register bit IRQ_2_EXT_EN (register 0x04, TRX_CTRL_1).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
168
11.7 Frame Buffer Empty Indicator
11.7.1 Overview
For time critical applications that want to start reading the frame data as early as
possible, the Atmel AT86RF233 Frame Buffer status can be indicated to the
microcontroller through a dedicated pin. This pin indicates to the microcontroller if an
access to the Frame Buffer is not possible since valid PSDU data are missing.
Pin 24 (IRQ) can be configured as a Frame Buffer Empty Indicator during a Frame
Buffer read access. This mode is enabled by register bit RX_BL_CTRL (register 0x04,
TRX_CTRL_1). The IRQ pin turns into Frame Buffer Empty Indicator after the Frame
Buffer read access command, see note (1) in Figure 11-25, has been transferred on the
SPI bus until the Frame Buffer read procedure has finished indicated by /SEL = H, see
note (4).
Figure 11-25. Timing Diagram of Frame Buffer Empty Indicator.
/SEL
MOSI
MISO
IRQ
SCLK
Command
PHY_STATUS
XX
IRQ_STATUS
Command
TRX_STATUS
XX
PHR[7:0]
XX
PSDU[7:0]
IRQ_2 (RX_START)
XX
PSDU[7:0]
XX
PSDU[7:0]
t12
XX
RX_STATUS
Command
TRX_STATUS
XX
IRQ_STATUS
IRQ_3 (TRX_END)
Frame Buffer Empty Indicator
(1) (4)(3)Notes (2)
XX
LQI[7:0]
XX
ED[7:0]
Notes: 1. Timing figure t12 refer to Section 12.4.
2. A Frame Buffer read access can proceed as long as pin 24 (IRQ) = L.
3. Pin IRQ =
H indicates that the Frame Buffer is currently not ready for another
SPI cycle.
4. The Frame Buffer read procedure has finished indicated by /SEL = H.
The microcontroller has to observe the IRQ pin during the Frame Buffer read
procedure. A Frame Buffer read access can proceed as long as pin 24 (IRQ) = L, see
note (2). When the IRQ output pin is pulled high (IRQ = H) , the Frame Buffer is not
ready for another SPI cycle, see note (3) above. The read operation can be resumed as
the IRQ output pin is pulled low again (IRQ = L) to indicate new data in the buffer.
On Frame Buffer read access, three more byte are transferred via MISO after PHR and
PSDU data, namely LQI, ED, and RX_STATUS; refer to Section 6.3.2. Because these
bytes are appended and physically not stored in the frame buffer, they are ignored for
Frame Buffer empty indication.
The Frame Buffer Empty Indicator pin 24 (IRQ) becomes valid after t12 = 750ns starting
from the last SCLK rising edge while reading a Frame Buffer command byte, see figure
above.
Upon completing the SPI frame data receive task, SPI read access can be disabled by
pulling /SEL = H, note (4). At this time the IRQ output pin 24 (IRQ) ) can be used as an
output to flag pending interrupts to the processor.
If during the Frame Buffer read access a receive error occurs (for example an PLL
unlock), the Frame Buffer Empty Indicator locks on 'empty' (pin 24 (IRQ) = H) too. To
prevent possible deadlocks, the microcontroller should impose a timeout counter that
checks whether the Frame Buffer Empty Indicator remains logic high for more than two
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
169
octet periods. A new byte must have been arrived at the frame buffer during that period.
If not, the Frame Buffer read access should be aborted.
11.7.2 Register Description
Register 0x04 (TRX_CTRL_1):
The TRX_CTRL_1 register is a multi-purpose register to control various operating
modes and settings of the radio transceiver.
Figure 11-26. Register TRX_CTRL_1.
Bit 7 6 5 4
0x04 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_
ON
RX_BL_CTRL TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
Bit 3 2 1 0
0x04
SPI_CMD_MODE
IRQ_MASK_MODE
IRQ_POLARITY
TRX_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 1 0
• Bit 4 - RX_BL_CTRL
The register bit RX_BL_CTRL controls the Frame Buffer Empty Indicator.
Table 11-22. RX_BL_CTRL.
Register Bits Value Description
RX_BL_CTRL 0 Frame Buffer Empty Indicator disabled
1 Frame Buffer Empty Indicator enabled
Note: 1.
A modification of register bit IRQ_POLARITY has no influence to RX_BL_CTRL
behavior.
If this register bit is set, the Frame Buffer Empty Indicator is enabled. After sending a
Frame Buffer read command (refer to Section 6.3), pin 24 (IRQ) indicates that an
access to the Frame Buffer is not possible since PSDU data are not available yet.
The pin 24 (IRQ) does not indicate any interrupts during this time.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
170
11.8 Dynamic Frame Buffer Protection
11.8.1 Overview
The Atmel AT86RF233 continues the reception of incoming frames as long as it is in
any receive state. When a frame was successfully received and stored into the Frame
Buffer, the following frame will overwrite the Frame Buffer content again.
To relax the timing requirements for a Frame Buffer read access the Dynamic Frame
Buffer Protection prevents that a new valid frame passes to the Frame Buffer until a
Frame Buffer read access has ended (indicated by /SEL = H, refer to Section 6.3).
A received frame is automatically protected against overwriting:
• in Basic Operating Mode, if its FCS is valid
• in Extended Operating Mode, if an IRQ_3 (TRX_END) is generated.
The Dynamic Frame Buffer Protection is enabled with RX_SAFE_MODE
(register 0x0C, TRX_CTRL_2) set and applicable in transceiver states RX_ON and
RX_AACK_ON.
Note: 1. The Dynamic Frame Buffer Protection only prevents write accesses from the air
interface – not from the SPI interface. A Frame Buffer or SRAM write access
may still modify the Frame Buffer content.
11.8.2 Register Description
Register 0x0C (TRX_CTRL_2):
The TRX_CTRL_2 register is a multi-purpose control register to control various settings
of the radio transceiver.
Figure 11-27. Register TRX_CTRL_2.
Bit 7 6 5 4
0x0C RX_SAFE_MODE reserved OQPSK_SCRAM_
EN
reserved TRX_CTRL_2
Read/Write R/W R R/W R
Reset value
0 0 1 0
Bit 3 2 1 0
0x0C
reserved
OQPSK_DATA_RATE
TRX_CTRL_2
Read/Write R R/W R/W R/W
Reset value
0 0 0 0
• Bit 7 - RX_SAFE_MODE
Protect Frame Buffer after frame reception with valid FCF check.
Table 11-23. RX_SAFE_MODE.
Register Bits Value Description
RX_SAFE_MODE 0 Disable Dynamic Frame Buffer protection
1(1) Enable Dynamic Frame Buffer protection
Note: 1.
Dynamic Frame Buffer Protection is released on the rising edge of pin 23 (/SEL)
during a Frame Buffer read access, or on the radio transceiver’s state change from
RX_ON or RX_AACK_ON to another state.
This operation mode is independent of the setting of register bits RX_PDT_LEVEL,
(register 0x15, RX_SYN), refer to Section 9.1.3.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
171
11.9 Alternate Start-Of-Frame Delimiter
11.9.1 Overview
The SFD (start of frame delimiter) is a field indicating the end of the SHR and the start
of the packet data. The length of the SFD is one octet (two symbols for O-QPSK). The
octet is used for byte synchronization only and is not included in the Atmel AT86RF233
Frame Buffer.
The value of the SFD can be changed if it is needed to operate in non-IEEE 802.15.4
compliant networks. A node with a non-standard SFD value cannot synchronize with
any of the IEEE 802.15.4 network nodes.
Due to the way the SHR is formed, it is not recommended to set the low-order four bits
to zero. The LSB of the SFD is transmitted first, that is right after the last bit of the
preamble sequence.
11.9.2 Register Description
Register 0x0B (SFD_VALUE):
The SFD_VALUE register contains the one octet start-of-frame delimiter (SFD).
Figure 11-28. Register SFD_VALUE.
Bit 7 6 5 4
0x0B
SFD_VALUE
SFD_VALUE
Read/Write R/W R/W R/W R/W
Reset value
1 0 1 0
Bit 3 2 1 0
0x0B
SFD_VALUE
SFD_VALUE
Read/Write R/W R/W R/W R/W
Reset value
0 1 1 1
• Bit 7:0 - SFD_VALUE
The register bits SFD_VALUE are required for transmit and receive operation.
Table 11-24. SFD_VALUE.
Register Bits Value Description
SFD_VALUE 0xA7 For transmission this value is copied into start-of-frame
delimiter (SFD) field of frame header. For reception this
value is checked for incoming frames.
The default value is according to IEEE 802.15.4
specification.
For IEEE 802.15.4 compliant networks, set SFD_VALUE = 0xA7 as specified in [2].
This is the default value of the register.
To establish non IEEE 802.15.4 compliant networks, the SFD value can be changed to
any other value. If enabled, IRQ_2 (RX_START) is issued only if the received SFD
matches SFD_VALUE and a valid PHR is received.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
172
11.10 Reduced Power Consumption Mode (RPC)
The Reduced Power Consumption mode is characterized by:
• Significant power reduction for several operating modes
• Self-contained, self-calibrating and adaptive power reduction schemes
11.10.1 Overview
Atmel AT86RF233 RPC offers a variety independent techniques and methods to
significantly reduce the power consumption. RPC is applicable to several operating
modes and transparent to other extended features.
Notes: 1. To achieve the lowest power consumption set register 0x16, TRX_RPC to
0xFF.
2. For disabling the Reduced Power Consumption modes set register 0x16,
TRX_RPC to 0xC1 or 0x01.
11.10.2 RPC Methods and Elements
11.10.2.1 PES – PLL Energy Saving
The PES mode is activated with register bit PLL_RPC_EN (register 0x16, TRX_RPC)
set to one.
Applicable to states: PLL_ON and TX_ARET_ON
A state change towards PLL_ON or TX_ARET_ON causes an initial PLL calibration run,
immediately followed by entering the PES mode. A state change towards RX or TX
states, a channel switch or PLL calibration causes a PLL wake-up. After finishing such
an operation, the PLL automatically enters the PES mode.
The typical current consumption IPLL_ON reduces from 5.2mA to 450µA.
11.10.2.2 SRT – Smart Receiving Technology
The SRT mode is activated with register bit RX_RPC_EN (register 0x16, TRX_RPC) set
to one.
Applicable to states: RX_ON, RX_AACK_ON and TX_ARET
SRT reduces the average power consumption during RX listening periods. In typical
environment situations SRT reduces the average current consumption IRX_ON by up to
50%. A configuration of SRT is done with register bits RX_RPC_CTRL (register 0x16,
TRX_RPC).
Notes: 1. It’s recommended to disable SRT during RSSI measurements or random
number generation, Section 8.4 and Section 11.2.
2. During CCA or/and ED scan the SRT is disabled automatically.
3. If autonomous antenna diversity is enabled, SRT cannot achieve the maximum
effect.
4.
Depending on operating conditions (traffic, temperature, channel noise,
frequency settings) the effective reduction of current consumption may vary.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
173
11.10.2.3 ERD – Extended Receiver Desensitizing
Atmel AT86RF233 ERD is activated with register bit PDT_RPC_EN (register 0x16,
TRX_RPC) set to one.
Applicable to states: RX, RX_AACK and TX_ARET
In combination with RX_PDT_LEVEL settings, the average RX current is further
significantly reduced, for details refer to Section 12.8.
An RX_PDT_LEVEL = 0x08 setting requires special attention. In contrast to definitions
in Table 9-3, the sensitivity is reduced to -83dBm only, but at much lower average RX
listen current than comparable register settings.
Notes: 1. With RX_PDT_LEVEL = 0x08, RSSI/ED can not resolve RX input levels from
-83dBm to -70dBm.
2. During CCA or/and ED scan the ERD is disabled automatically.
11.10.2.4 TPH – Automated TX Power Handling
TPH is activated with register bit XAH_TX_RPC_EN (register 0x16, TRX_RPC) set to
one.
Applicable to states: RX_AACK
ACK frame TX output power setting is automatically adapted according to a
combination of received RX frame ED and LQI values. If an expected frame has been
successfully received with ED > -77dBm and LQI > 224, the TX output power is
reduced. The minimum power is -17dBm (ED > -45dBm and LQI > 224), whereas the
maximum is set be register bits TX_PWR (register 0x05, PHY_TX_PWR).
Reading the TX_PWR field provides the used transmit power for last transmitted frame
including acknowledgement frame. This allows monitoring the actual RPC handling
used for transmitting. See register bits TX_PWR description for further information.
The Table 11-25 shows the typical current consumption for dedicated TX output power
values.
Table 11-25. TX Output Power versus Current Consumption (extraction).
Register Bits TX Output Power [dBm] Current Consumption [mA]
TX_PWR +4 13.8
+0 11.8
-17 7.2
Notes: 1. The upper limit will be declared by register bits TX_PWR (register 0x05,
PHY_TX_PWR), refer to Section 9.2.5.
2. If the sequence number, refer to Section 8.1.2, from previous received frame
equal to the current frame sequence number, then no automatic TX power
reduction will be activated.
Applicable to states: TX_ARET
If the first frame transmission fails, using a reduced TX output power as set by register
bits TX_PWR (register 0x05, PHY_TX_PWR), the next frame retry starts with maximum
TX output power (+4dBm).
Note: 3. The lower limit for the first frame transmitting will be declared by register bits
TX_PWR (register 0x05, PHY_TX_PWR), refer to Section 9.2.5.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
174
Achievable TX current consumption IBUSY_TX reductions are shown in Section 12.8 or
Table 11-25.
11.10.2.5 PAM – PAN Address Match Recognition
Atmel AT86RF233 PAM is activated with register bit IPAN_RPC_EN (register 0x16,
TRX_RPC) set to one.
Applicable to states: RX_AACK
Address match fail indication of the IEEE 802.15.4 frame filtering causes stopping of the
receive procedure in two ways:
1. If PAN address does not match, a new listen period starts immediately,
2. If PAN address matches, the radio transceiver enters power saving mode for the
remaining frame and ACK period, if an ACK is requested.
Notes: 1.
PAM is applicable to short ACK time and reserved frames types as set by
register bit AACK_ACK_TIME and register bit AACK_FLTR_RES_FT
(register 0x17, XAH_CTRL_1), respectively.
2. If promiscuous mode is enabled with AACK_PROM_MODE (register 0x17,
XAH_CTRL_1) set, PAM is disabled automatically.
11.10.2.6 Miscellaneous Power Reduction Functions
Applicable to states: RX and RX_AACK
In addition to Dynamic Frame Buffer Protection, refer to Section 11.8:
During Dynamic Frame Buffer Protection, the radio transceiver automatically enters the
power save mode.
Applicable to states: TX_ARET
In addition to CSMA-CA retry, refer to Section 7.2.4:
After starting the TX_ARET transaction, a random backoff period is performed. Within
this backoff period the radio transceiver automatically enters power saving mode.
Applicable to states: TX_ARET and RX_AACK
In addition to TX/RX turnaround time, refer to Section 7.2:
The radio transceiver automatically enters power saving mode in:
• TX_ARET: during the time waiting for an ACK frame, or
• RX_AACK: during the time waiting for ACK transmission
Note: 1.
To handle nodes configured with a RX/TX turnaround time less than
12 symbols, register bits are to be set to RX_RPC_CTRL = 0 within TX_ARET.
Alternatively, register bit AACK_ACK_TIME (register 0x17, XAH_CTRL_1) can
be set to one.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
175
11.10.3 Register Summary
Register 0x16 (TRX_RPC):
The TRX_RPC register controls the Reduce Power Consumption modes.
Figure 11-29. Register TRX_RPC.
Bit 7 6 5 4
0x16
RX_RPC_CTRL
RX_RPC_EN
PDT_RPC_EN
TRX_RPC
Read/Write R/W R/W R/W R/W
Reset value
1 1 0 0
Bit 3 2 1 0
0x16
PLL_RPC_EN
XAH_TX_RPC_EN
IPAN_RPC_EN
reserved
TRX_RPC
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 1
Note: 1. The reserved bit needs to be set one for write access.
• Bit 7:6 - RX_RPC_CTRL
The register bits RX_RPC_CTRL are used for internal performance settings within
Smart Receiving mode.
Table 11-26. RX_RPC_CTRL.
Register Bits Value Description
RX_RPC_CTRL 0 Activates minimum power saving behavior for Smart
Receiving mode
3 Activates maximum power saving behavior for Smart
Receiving mode
All other values are reserved
• Bit 5 - RX_RPC_EN
The register bit RX_RPC_EN activates the Smart Receiving mode for all RX listening
modes.
Table 11-27. RX_RPC_EN.
Register Bits Value Description
RX_RPC_EN 0 Smart receiving mode is disabled
1 Smart receiving mode is enabled
• Bit 4 - PDT_RPC_EN
The register bit PDT_RPC_EN controls in combination with the RX_PDT_LEVEL value
the reduced sensitivity behavior under the RPC mode.
Table 11-28. PDT_RPC_EN.
Register Bits Value Description
PDT_RPC_EN 0 The reduced sensitivity RPC mode is disabled
1 The reduced sensitivity RPC mode is enabled
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
176
• Bit 3 - PLL_RPC_EN
The register bit PLL_RPC_EN controls the extended PLL behavior within PLL_ON and
TX_ARET_ON modes.
Table 11-29. PLL_RPC_EN.
Register Bits Value Description
PLL_RPC_EN 0 The extended PLL behavior is disabled
1 The extended PLL behavior is enabled
• Bit 2 - XAH_TX_RPC_EN
The register bit XAH_TX_RPC_EN controls in combination with the TX_PWR value the
automatic TX power handling within the Extended Operating Mode.
Table 11-30. XAH_TX_RPC_EN.
Register Bits Value Description
XAH_TX_RPC_EN 0 The automatic TX power handling is disabled
1 The automatic TX power handling is enabled
• Bit 1 - IPAN_RPC_EN
The register bit IPAN_RPC_EN controls the own PAN handling within the RPC mode.
Table 11-31. IPAN_RPC_EN.
Register Bits Value Description
IPAN_RPC_EN 0 The RPC PAN handling is disabled
1 The RPC PAN handling is enabled
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
177
11.11 Time-Of-Flight Module (TOM)
The time-of-flight measurement functions are characterized by:
• 24-bit Timer/Counter (T/C)
• Automated T/C start, capturing and reset
• Reference frequency error measurement
• Preamble synchronization monitoring
11.11.1 Overview
The AT86RF233 includes a set of means to trigger time measurements during message
transfer.
11.11.2 Interrupt Handling
If TOM mode is enabled, it causes the generation of IRQ_2 (RX_START) interrupts for
all received frames, even with PHR set to zero and IRQ_2 (RX_START) is enabled.
11.11.3 TOM Measurements
11.11.3.1 24-bit Timer/Counter
The AT86RF233 features a 24-bit Timer/Counter (T/C), which is automatically started,
captured or reset. The actual action depends on specified events and operating modes.
The T/C is operated at 16MHz. If a timer event occurs, the current time stamp is
captured to the Frame Buffer. The timer is reset and started automatically. An exeption
is the RX synchronization mode: if the SFD is not equal to 0xA7. In this case, the
current counter value is only captured to the Frame Buffer.
T/C Content Access
With TOM mode enabled, the 24-bit T/C value (TIM) is mapped to Frame Buffer
address space 0x7D, …, 0x7F.
• TIM_0: Frame Buffer Address (0x7D) : T/C [7:0]
• TIM_1: Frame Buffer Address (0x7E) : T/C [15:8]
• TIM_2: Frame Buffer Address (0x7F) : T/C [23:16]
Events
The Timer/Counter is controlled as follow:
Table 11-32. 24-bit Timer/Counter Event Overview
Event Delay [µs] Capture Reset Start
TX start (rising edge of signal SLP_TR) 16.125 x x x
RX Synchronization; at detection of SFD
(SFD is equal 0xA7) 80 x x x
RX Synchronization; at detection of SFD
(SFD is not equal 0xA7) 80 x
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
178
11.11.3.2 Reference Frequency Error Measurement
During frame reception and register bit TOM_EN is set wihin the AT86RF233, the
frequency error between two peer devices is estimated. The frequency error calculation
(FEC) value is accessible from Frame Buffer address 0x7C.
The 8-bit value represents the drift between two successive received chips (0.5µs) with
a granularity of 180°/256. The value is accessible after IRQ_2 (RX_START) and
updated after IRQ_3 (TRX_END). It is interpreted as a two’s complement signed value
in range of -500kHz, …, <500kHz, respectively.
The frequency offset can be calculated as follow:
foffs[ppm] = FEC x (500000 / 128) / fRF[MHz]
11.11.3.3 Preamble Fine Synchronization Monitoring
During receive the radio transceiver searches for SHR symbols and SFD initially. The
register bits PEL_SHIFT_VALUE (register 0x0A, RX_CTRL) signals an early/late
behaviour relative to the determined discrete, 16MHz based, synchronization time
stamp.
As an alternative to the PEL_SHIFT_VALUE value the complex magnitude values from
the synchronization module can be used for a better time stamp estimation. With TOM
mode enabled, the complex magnitude values (CPM) from the symbol cross correlator
are mapped to Frame Buffer address space 0x73, …, 0x7C.
• CPM_0: Frame Buffer Address (0x73)
• …
• CPM_8: Frame Buffer Address (0x7C)
11.11.3.4 Storage of Measurment Results
Using TOM mode, the Frame Buffer address space 0x73, …, 0x7F is reserved to store
captured T/C content and other data. This limits the number of usable PSDU octets for
standard operation to 114. Any received frame exceeding this number corrupts data
stored in the Frame Buffer address starting from address 0x73.
Notes: 1. Basic Operating Mode within TX states: If TOM_EN is still set, but not required
for the actual transaction, it is possible to transmit up to 127 octets by writing
PSDU data to the Frame Buffer after initiating the transmission with rising edge
of pin 11 (SLP_TR) or TX_START command.
2. Extended Operating Mode within TX_ARET states: If TOM_EN is still set, but
not required for the actual transaction, it is possible to transmit up to 127 octets
by writing PSDU data to the Frame Buffer after initiating the transmission with
rising edge of pin 11 (SLP_TR)
or TX_START command and
MAX_FRAME_RETRIES (register 0x2C, XAH_CTRL_0) set to zero.
3. Reception of an ACK frame causes mapping of TOM measurement results to
Frame Buffer address space 0x73, …, 0x7F.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
179
11.11.4 Register Summary
Register 0x03 (TRX_CTRL_0):
The TRX_CTRL_0 register controls the CLKM clock rate.
Figure 11-30. Register TRX_CTRL_0.
Bit 7 6 5 4
0x03 TOM_EN reserved PMU_EN PMU_IF_
INVERSE
TRX_CTRL_0
Read/Write R/W R R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x03
CLKM_SHA_SEL
CLKM_CTRL
TRX_CTRL_0
Read/Write R/W R/W R/W R/W
Reset value
1 0 0 1
• Bit 7 - TOM_EN
The register bit TOM_EN controls the Time-Of-Flight Measurement mode.
Table 11-33. TOM_EN.
Register Bits Value Description
TOM_EN 0 TOM mode is disabled
1 TOM mode is enabled
Register 0x0A (RX_CTRL):
The RX_CTRL register controls the sensitivity of the Antenna Diversity mode and
indicates the receiver synchronization behavior.
Figure 11-31. Register RX_CTRL.
Bit
7
6
5
4
0x0A PEL_SHIFT_VALUE reserved RX_CTRL
Read/Write
R
R
R/W
R/W
Reset value
0
0
1
1
Bit
3
2
1
0
0x0A PDT_THRES RX_CTRL
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
1
1
1
• Bit 7:6 - PEL_SHIFT_VALUE
The register bits PEL_SHIFT_VALUE signals the synchronization shift behavior.
Table 11-34. PEL_SHIFT_VALUE.
Register Bits Value Description
PEL_SHIFT_VALUE 0 Synchronization behavior is normal
1 Synchronization behavior is early
2 Synchronization behavior is late
All other values are reserved
Register 0x17 (XAH_CTRL_1):
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
180
The XAH_CTRL_1 register is a multi-purpose controls register for Extended Operating
Mode.
Figure 11-32. Register XAH_CTRL_1.
Bit 7 6 5 4
0x17 ARET_TX_TS_EN reserved AACK_FLTR_RES_
FT
AACK_UPLD_RES_
FT
XAH_CTRL_1
Read/Write R/W R/W R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x17 reserved AACK_ACK_TIME AACK_PROM_
MODE
AACK_SPC_EN XAH_CTRL_1
Read/Write R R/W R/W R/W
Reset value
0 0 0 0
• Bit 0 - AACK_SPC_EN
The register bit AACK_SPC_EN enables the synchronization point correction (SPC)
within RX_AACK mode. If SPC is enabled, then acknowledgement frame start time will
be corrected against PEL_SHIFT_VALUE content.
Table 11-35. AACK_SPC_EN.
Register Bits Value Description
AACK_SPC_EN 0 Synchronization point correction is disabled
1 Synchronization point correction is enabled
11.11.5 Frame Buffer Content Summary
Register 0x73 (TOM_CPM_0) for TOM_EN=0x01:
The TOM_CPM_0 register contains the result of synchronization correlator.
Figure 11-33. Register TOM_CPM_0.
Bit
7
6
5
4
0x73 CPM_0 TOM_CPM_0
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x73 CPM_0 TOM_CPM_0
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - CPM_0
This register contains the CPM_0 value.
Table 11-36. CPM_0.
Register Bits Value Description
CPM_0 0x00
Complex magnitude value; distance from main peak minus
1000ns.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x74 (TOM_CPM_1) for TOM_EN=0x01:
The TOM_CPM_1 register contains the result of synchronization correlator.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
181
Figure 11-34. Register TOM_CPM_1.
Bit 7 6 5 4
0x74
CPM_1
TOM_CPM_1
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x74
CPM_1
TOM_CPM_1
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - CPM_1
This register contains the CPM_1 value.
Table 11-37. CPM_1.
Register Bits Value Description
CPM_1 0x00
Complex magnitude value; distance from main peak minus
750ns.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x75 (TOM_CPM_2) for TOM_EN=0x01:
The TOM_CPM_2 register contains the result of synchronization correlator.
Figure 11-35. Register TOM_CPM_2.
Bit
7
6
5
4
0x75
CPM_2
TOM_CPM_2
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x75
CPM_2
TOM_CPM_2
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - CPM_2
This register contains the CPM_2 value.
Table 11-38. CPM_2.
Register Bits Value Description
CPM_2 0x00
Complex magnitude value; distance from main peak minus
500ns.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
182
Register 0x76 (TOM_CPM_3) for TOM_EN=0x01:
The TOM_CPM_3 register contains the result of synchronization correlator.
Figure 11-36. Register TOM_CPM_3.
Bit 7 6 5 4
0x76
CPM_3
TOM_CPM_3
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x76
CPM_3
TOM_CPM_3
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - CPM_3
This register contains the CPM_3 value.
Table 11-39. CPM_3.
Register Bits Value Description
CPM_3 0x00
Complex magnitude value; distance from main peak minus
250ns.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x77 (TOM_CPM_4) for TOM_EN=0x01:
The TOM_CPM_4 register contains the result of synchronization correlator.
Figure 11-37. Register TOM_CPM_4.
Bit
7
6
5
4
0x77
CPM_4
TOM_CPM_4
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x77
CPM_4
TOM_CPM_4
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - CPM_4
This register contains the CPM_4 value.
Table 11-40. CPM_4.
Register Bits Value Description
CPM_4 0x00 Complex magnitude value; distance from main peak 0ns.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
183
Register 0x78 (TOM_CPM_5) for TOM_EN=0x01:
The TOM_CPM_5 register contains the result of synchronization correlator.
Figure 11-38. Register TOM_CPM_5.
Bit 7 6 5 4
0x78
CPM_5
TOM_CPM_5
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x78
CPM_5
TOM_CPM_5
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - CPM_5
This register contains the CPM_5 value.
Table 11-41. CPM_5.
Register Bits Value Description
CPM_5 0x00 Complex magnitude value; distance from main peak plus
250ns.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x79 (TOM_CPM_6) for TOM_EN=0x01:
The TOM_CPM_6 register contains the result of synchronization correlator.
Figure 11-39. Register TOM_CPM_6.
Bit
7
6
5
4
0x79
CPM_6
TOM_CPM_6
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x79
CPM_6
TOM_CPM_6
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - CPM_6
This register contains the CPM_6 value.
Table 11-42. CPM_6.
Register Bits Value Description
CPM_6 0x00 Complex magnitude value; distance from main peak plus
500ns.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
184
Register 0x7A (TOM_CPM_7) for TOM_EN=0x01:
The TOM_CPM_7 register contains the result of synchronization correlator.
Figure 11-40. Register TOM_CPM_7.
Bit 7 6 5 4
0x7A
CPM_7
TOM_CPM_7
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x7A
CPM_7
TOM_CPM_7
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - CPM_7
This register contains the CPM_7 value.
Table 11-43. CPM_7.
Register Bits Value Description
CPM_7 0x00 Complex magnitude value; distance from main peak plus
750ns.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x7B (TOM_CPM_8) for TOM_EN=0x01:
The TOM_CPM_8 register contains the result of synchronization correlator.
Figure 11-41. Register TOM_CPM_8.
Bit
7
6
5
4
0x7B
CPM_8
TOM_CPM_8
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x7B
CPM_8
TOM_CPM_8
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - CPM_8
This register contains the CPM_8 value.
Table 11-44. CPM_8.
Register Bits Value Description
CPM_8 0x00 Complex magnitude value; distance from main peak plus
1000ns.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
185
Register 0x7C (TOM_FEC) for TOM_EN=0x01:
The TOM_FEC register contains the result of a frequency offset measurement.
Figure 11-42. Register TOM_FEC.
Bit 7 6 5 4
0x7C
FEC
TOM_FEC
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x7C
FEC
TOM_FEC
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - FEC
This register contains the FEC value. An initial frequency offset estimation is available
after PHR field detection. An accumulated frequency offset measurement value over
the frame duration is available at frame end.
Table 11-45. FEC.
Register Bits Value Description
FEC 0x00 Two’s complement signed value in range of -90Deg, …,
90Deg.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x7D (TOM_TIM_0) for TOM_EN=0x01:
This register contains the lower 8-bit of the time-of-flight measurement, bits[7:0].
Figure 11-43. Register TOM_TIM_0.
Bit
7
6
5
4
0x7D
TIM_0
TOM_TIM_0
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x7D
TIM_0
TOM_TIM_0
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - TIM_0
Lower 8-bit of time-of-flight measurement, bits[7:0]
Table 11-46. TIM_0.
Register Bits Value Description
TIM_0 0x00 Timer/Counter measurement value based on 16MHz.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
186
Register 0x7E (TOM_TIM_1) for TOM_EN=0x01:
This register contains 8-bit of the time-of-flight measurement, bits[15:8].
Figure 11-44. Register TOM_TIM_1.
Bit 7 6 5 4
0x7E
TIM_1
TOM_TIM_1
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x7E
TIM_1
TOM_TIM_1
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - TIM_1
8-bit of time-of-flight measurement, bits[15:8]
Table 11-47. TIM_1.
Register Bits Value Description
TIM_1 0x00 Timer/Counter measurement value based on 16MHz.
Valid values are [0xFF, 0xFE, …, 0x00].
Register 0x7F (TOM_TIM_2) for TOM_EN=0x01:
This register contains the higher 8-bit of the time-of-flight measurement, bits[23:16].
Figure 11-45. Register TOM_TIM_2.
Bit
7
6
5
4
0x7F
TIM_2
TOM_TIM_2
Read/Write
R
R
R
R
Reset value
0
0
0
0
Bit
3
2
1
0
0x7F
TIM_2
TOM_TIM_2
Read/Write
R
R
R
R
Reset value
0
0
0
0
• Bit 7:0 - TIM_2
Higher 8-bit of time-of-flight measurement, bits[23:16]
Table 11-48. TIM_2.
Register Bits Value Description
TIM_2 0x00 Timer/Counter measurement value based on 16MHz.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
187
11.12 Phase Difference Measurement
The Phase Difference Measurement Unit (PMU) is characterized by:
• Relative phase measurement of received signal
11.12.1 Overview
The AT86RF233 performs a phase measurement of a received signal relative to an
internal reference. The derived value represents the phase delay of the received signal
referenced to an internal reference signal in the receiver low-IF domain, see
Section 9.1. The measured value is captured in register bits PMU_VALUE
(register 0x3B, PHY_PMU_VALUE) and periodically updated.
11.12.2 Register Summary
Register 0x03 (TRX_CTRL_0):
The TRX_CTRL_0 register controls the CLKM clock rate.
Figure 11-46. Register TRX_CTRL_0.
Bit 7 6 5 4
0x03 TOM_EN reserved PMU_EN PMU_IF_
INVERSE
TRX_CTRL_0
Read/Write R/W R R/W R/W
Reset value
0 0 0 0
Bit 3 2 1 0
0x03
CLKM_SHA_SEL
CLKM_CTRL
TRX_CTRL_0
Read/Write R/W R/W R/W R/W
Reset value
1 0 0 1
• Bit 5 - PMU_EN
The register bit PMU_EN controls the Phase Difference Measurement Unit mode.
Table 11-49. PMU_EN.
Register Bits Value Description
PMU_EN 0 PMU mode is disabled
1 PMU mode is enabled
• Bit 4 - PMU_IF_INVERSE
The register bit PMU_IF_INVERSE controls the PMU Intermediate Frequency path.
Table 11-50. PMU_IF_INVERSE.
Register Bits Value Description
PMU_IF_INVERSE 0 Normal IF position
1 Inverse IF position
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
188
Register 0x3B (PHY_PMU_VALUE) for PMU_EN=0x01:
Figure 11-47. Register PHY_PMU_VALUE.
Bit 7 6 5 4
0x3B PMU_VALUE PHY_PMU_VALU
E
Read/Write R R R R
Reset value
0 0 0 0
Bit 3 2 1 0
0x3B PMU_VALUE PHY_PMU_VALU
E
Read/Write R R R R
Reset value
0 0 0 0
• Bit 7:0 - PMU_VALUE
The register bits PMU_VALUE signals the PMU measurement value.
Table 11-51. PMU_VALUE.
Register Bits Value Description
PMU_VALUE 0x00 Signals 8-bit PMU measurement value. The value is
updated every 8µs.
Valid values are [0xFF, 0xFE, …, 0x00].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
189
12 Electrical Characteristics
12.1 Absolute Maximum Ratings
Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions beyond those indicated
in the operational sections of this specification are not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device
reliability.
Symbol Parameter Condition Min. Typ. Max. Unit
TSTOR Storage temperature -50 150 °C
TLEAD Lead temperature T = 10s
(soldering profile compliant with
IPC/JEDEC J STD 020B)
260 °C
VESD ESD robustness Human Body Model (HBM) [4], 4 kV
Charged Device Model (CDM) [5] 750 V
PRF Input RF level +10 dBm
VDIG Voltage on all pins
(except pins 4, 5, 13, 14, 29)
-0.3 VDD+0.3 V
VANA Voltage on pins 4, 5, 13, 14, 29 -0.3 2.0 V
12.2 Recommended Operating Range
Symbol Parameter Condition Min. Typ. Max. Unit
TOP Operating temperature range -40 +25 +85 °C
VDD Supply voltage Voltage on pins 15, 28(1) 1.8 3.0 3.6 V
VDD1.8 Supply voltage (on pins 13, 14, 29) External voltage supply(2) 1.7 1.8 1.9 V
Notes: 1. Even if an implementation uses the external 1.8V voltage supply VDD1.8 it is required to connect VDD.
2. Register 0x10 (VREG_CTRL) needs to be programmed to disable internal voltage regulators and supply blocks by an
external 1.8V supply, refer to Section 9.4.
Caution! ESD sensitive device.
Precaution should be used when handling the device in order to prevent
permanent damage.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
190
12.3 Digital Pin Characteristics
Test Conditions: TOP = +25°C (unless otherwise stated).
Symbol Parameter Condition Min. Typ. Max. Unit
VIH High level input voltage(1) VDD-0.4 V
VIL Low level input voltage(1) 0.4 V
VOH High level output voltage(1) VDD-0.4 V
VOL Low level output voltage(1) 0.4 V
CLoad Capacitive load(1) 50 pF
Note: 1. The capacitive load CLoad should not be larger than 50pF for all I/Os. Generally, large load capacitances increase the
overall current consumption.
12.4 Digital Interface Timing Characteristics
Test Conditions: TOP = +25°C, VDD = 3.0V, CLoad = 50pF (unless otherwise stated).
Symbol Parameter Condition Min. Typ. Max. Unit
fsync SCLK frequency Synchronous operation 8 MHz
fasync SCLK frequency Asynchronous operation 7.5 MHz
t1 /SEL falling edge to MISO active 180 ns
t2 SCLK falling edge to MISO out Data hold time 25 ns
t3 MOSI setup time 10 ns
t4 MOSI hold time 10 ns
t5 LSB last byte to MSB next byte SPI read/write, standard SRAM
and frame access modes
250(1) ns
t5a LSB last byte to MSB next byte Fast SRAM read/write access
mode
500(1) ns
t6 /SEL rising edge to MISO tri state 10 ns
t7 SLP_TR pulse width TX start trigger 62.5 Note(2) ns
t8 SPI idle time: SEL rising to falling edge SPI read/write, standard SRAM
and frame access modes
Idle time between consecutive
SPI accesses
250(1) ns
t8a SPI idle time: SEL rising to falling edge Fast SRAM read/write access
mode
Idle time between consecutive
SPI accesses
500(1) ns
t9 Last SCLK rising edge to /SEL rising
edge
250 ns
t10 Reset pulse width ≥ 10 clock cycles at 16MHz 625 ns
t11 SPI access latency after reset ≥ 10 clock cycles at 16MHz 625 ns
t12 Frame buffer empty indicator latency rising edge of last SCLK clock of
the Frame Buffer read command
byte to rising edge of IRQ
750 ns
tIRQ IRQ_2, IRQ_3, IRQ_4 latency Relative to the event to be
indicated
9 µs
fCLKM Output clock frequency at pin 17 (CLKM) Configurable in register 0x03
CLKM_CTRL = 0
0 MHz
CLKM_CTRL = 1 1 MHz
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
191
Symbol Parameter Condition Min. Typ. Max. Unit
CLKM_CTRL = 2 2 MHz
CLKM_CTRL = 3 4 MHz
CLKM_CTRL = 4 8 MHz
CLKM_CTRL = 5 16 MHz
CLKM_CTRL = 6 250 kHz
CLKM_CTRL = 7 62.5 kHz
Notes: 1. For Fast SRAM read/write accesses on address space 0x82 – 0x94 the time t5(Min.) and t8(Min.) increases to 500ns.
2. Maximum pulse width less than (TX frame length + 16µs).
12.5 General RF Specifications
Test Conditions (unless otherwise stated):
VDD = 3.0V, fRF = 2445MHz, TOP = +25°C, Measurement setup see Figure 5-1.
Symbol Parameter Condition Min. Typ. Max. Unit
fRF Frequency range As specified in [1], [2] 2405 2445 2480 MHz
500kHz spacing 2322 2527 MHz
fCH Channel spacing As specified in [1], [2] 5 MHz
500kHz spacing 500 kHz
fHDR Header bit rate (SHR, PHR) As specified in [1], [2] 250 kb/s
fPSDU PSDU bit rate As specified in [1], [2] 250 kb/s
OQPSK_DATA_RATE = 1 500 kb/s
OQPSK_DATA_RATE = 2 1000 kb/s
OQPSK_DATA_RATE = 3 2000 kb/s
fCHIP Chip rate As specified in [1], [2] 2000 kchip/s
fCLK Crystal oscillator frequency Reference oscillator 16 MHz
fSRD Symbol rate deviation
Reference frequency accuracy for
correct functionality
PSDU bit rate
250kb/s -60(1) +60 ppm
500kb/s -40 +40 ppm
1000kb/s -40 +40 ppm
2000kb/s -30 +30 ppm
f20dB 20dB bandwidth 2.8 MHz
Note: 1. A reference frequency accuracy of ±40ppm is required by [1], [2].
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
192
12.6 Transmitter Characteristics
Test Conditions (unless otherwise stated):
VDD = 3.0V, fRF = 2445MHz, TOP = +25°C, Measurement setup see Figure 5-1.
Symbol Parameter Condition Min. Typ. Max. Unit
PTX_MAX TX Output power Maximum configurable TX output
power value
Register bit TX_PWR = 0
+4 dBm
PRANGE Output power range 16 steps, configurable in register
0x05 (PHY_TX_PWR)
21 dB
PACC Output power tolerance ±2 dB
EVM Error vector magnitude 12 %rms
PHARM Harmonics 2nd harmonic -40 dBm
3rd harmonic -45 dBm
PSPUR_TX Spurious Emissions(1) 30 – ≤ 1000MHz -36 dBm
>1 – 12.75GHz -30 dBm
1.8 – 1.9GHz -47 dBm
5.15 – 5.3GHz -47 dBm
Note: 1. Complies with EN 300 328/440, FCC-CFR-47 part 15, ARIB STD-66, RSS-210.
12.7 Receiver Characteristics
Test Conditions (unless otherwise stated):
VDD = 3.0V, fRF = 2445MHz, TOP = +25°C, fPSDU = 250kb/s, Measurement setup see
Figure 5-1.
Symbol Parameter Condition Min. Typ. Max. Unit
PSENS Receiver sensitivity 250kb/s(1) -101 dBm
500kb/s(1) -96 dBm
1000kb/s(1) -94 dBm
2000kb/s(1) -88 dBm
Antenna Diversity
250kb/s(1)
-98 dBm
Smart Receiving
250kb/s(1)
-100 dBm
RLRX RX Return loss 100Ω differential impedance 10 dB
NF Noise figure 6 dB
PRX_MAX Maximum RX input level 250kb/s(1) 8 dBm
PACRN Adjacent channel rejection:
-5MHz
PRF= -82dBm(1) 32 dB
PACRP Adjacent channel rejection:
+5MHz
PRF= -82dBm(1) 35 dB
PAACRN Adjacent channel rejection:
-10MHz
PRF= -82dBm(1) 48 dB
PAACRP Adjacent channel rejection:
+10MHz
PRF= -82dBm(1) 48 dB
PAACR2N 2nd alternate channel rejection:
-15MHz
PRF= -82dBm(1) 54 dB
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
193
Symbol Parameter Condition Min. Typ. Max. Unit
PAACR2P 2nd alternate channel rejection:
+15MHz
PRF= -82dBm(1) 54 dB
PSPUR_RX Spurious emissions LO leakage -70 dBm
30 – ≤ 1000MHz -57 dBm
>1 – 12.75GHz -47 dBm
fCAR_OFFS TX/RX carrier frequency offset Sensitivity loss ≤ 2dB -300(2) +300 kHz
IIP3 3rd– order intercept point At maximum gain
Offset freq. interf. 1 = 5MHz
Offset freq. interf. 2 = 10MHz
-10 dBm
IIP2 2nd– order intercept point At maximum gain
Offset freq. interf. 1 = 60MHz
Offset freq. interf. 2 = 62MHz
31 dBm
RSSITOL RSSI tolerance Tolerance within gain step ±5 dB
RSSIRANGE RSSI dynamic range 87 dB
RSSIRES RSSI resolution 3 dB
RSSIBASE_V
AL
RSSI sensitivity Defined as RSSI_BASE_VAL -94 dBm
RSSIMIN Minimum RSSI value PRF≤ RSSI_BASE_VAL 0
RSSIMAX Maximum RSSI value PRF≥ RSSI_BASE_VAL + 84dB 28
Notes: 1. AWGN channel, PER ≤ 1%, PSDU length 20 octets.
2. Offset equals ±120ppm.
12.8 Current Consumption Specifications
Test Conditions (unless otherwise stated):
VDD = 3.0V, fRF = 2445MHz, TOP = +25°C, Measurement setup see Figure 5-1.
Symbol Parameter Condition Min. Typ. Max. Unit
IBUSY_TX Supply current transmit state PTX= +4dBm 13.8 mA
PTX= +0dBm 11.8 mA
PTX= -17dBm 7.2 mA
IRX_ON Supply current RX_ON state high sensitivity
RX_PDT_LEVEL = [0x0]
11.8 mA
with active RPC mode(2)
may further reduce current
consumptions
IRX_ON_L0 Supply current RX_ON state
with active receiver desensitize
receiver desensitize
RX_PDT_LEVEL = [0x1, ..., 0xE,
0xF](1)
11.3 mA
with active RPC mode(2)
may further reduce current
consumptions;
using RX_PDT_LEVEL = [0x8, ...,
0xE, 0xF](1)reduces current
consumption further by about
1mA
IPLL_ON Supply current PLL_ON state 5.2 mA
with active RPC mode(2) 450 µA
ITRX_OFF Supply current TRX_OFF state 300 µA
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
194
Symbol Parameter Condition Min. Typ. Max. Unit
ISLEEP Supply current SLEEP state 0.2 µA
IDEEP_SLEEP Supply current DEEP_SLEEP state 0.02 µA
Notes: 1. Refer to Section 9.1.
2. Refer to Section 11.10.
3. All power consumption measurements are performed with CLKM disabled.
12.9 Crystal Parameter Requirements
Test Conditions: TOP = +25°C, VDD = 3.0V (unless otherwise stated).
Symbol Parameter Condition Min. Typ. Max. Unit
f0 Crystal frequency 16 MHz
CL Load capacitance 8 14 pF
C0 Crystal shunt capacitance 7 pF
ESR Equivalent series resistance 100 Ω
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
195
13 Typical Characteristics
13.1 Active Supply Current
The following charts showing each a typical behavior of the Atmel AT86RF233. These
figures are not tested during manufacturing. All power consumption measurements are
performed with pin 17 (CLKM) disabled, unless otherwise stated. The measurement
setup used for the measurements is shown in Figure 5-1.
The power consumption of the microcontroller, which is required to program the radio
transceiver, is not included in the measurement results.
The power consumption in SLEEP and DEEP_SLEEP state is independent from CLKM
master clock rate selection.
The current consumption depends on several factors such as: operating voltage,
operating frequency, loading of I/O pins, switching rate of I/O pins, and ambient
temperature. The dominating factors are operating voltage and ambient temperature.
If possible the measurement results are not affected by current drawn from I/O pins.
Register, SRAM or Frame Buffer read or write accesses are not performed during
current consumption measurements.
13.1.1 P_ON and TRX_OFF states
Figure 13-1. Current Consumption in P_ON State.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
196
Figure 13-2. Current Consumption in TRX_OFF State.
13.1.2 PLL_ON state
Figure 13-3. Current Consumption in PLL_ON State.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
197
13.1.3 RX_ON state
Figure 13-4. Current Consumption in RX_ON State – High Sensitivity.
Figure 13-5. Current Consumption in RX_ON State – High Input Level.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
198
Figure 13-6. Current Consumption in RX_ON State – Reduced Sensitivity.
13.1.4 TX_BUSY state
Figure 13-7. Current Consumption in TX_BUSY State – Minimum Output Power.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
199
Figure 13-8. Current Consumption in TX_BUSY State – Output Power 0dBm.
Figure 13-9. Current Consumption in TX_BUSY State – Maximum Output Power.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
200
13.1.5 SLEEP
Figure 13-10. Current Consumption in SLEEP.
13.1.6 DEEP_SLEEP
Figure 13-11. Current Consumption in DEEP_SLEEP.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
201
13.2 State Transition Timing
Figure 13-12. Transition Time from EVDD to P_ON (CLKM available).
Figure 13-13. Transition Time from SLEEP to TRX_OFF (IRQ_4 (AWAKE_END)).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
202
Figure 13-14. Transition Time from TRX_OFF to PLL_ON.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
203
14 Register Reference
The Atmel AT86RF233 provides a register space of 64 8-bit registers used to configure,
control and monitor the radio transceiver.
Note: All registers not mentioned within the following table are reserved for internal
use and must not be overwritten. When writing to a register, any reserved bits
shall be overwritten only with their reset value.
Table 14-1. Register Summary.
Addr
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
0x01 TRX_STATUS CCA_DONE CCA_STATUS reserved TRX_STATUS 48, 68, 106
0x02 TRX_STATE TRAC_STATUS TRX_CMD 49, 69
0x03 TRX_CTRL_0 TOM_EN reserved PMU_EN PMU_IF_INVERSE CLKM_SHA_SEL CLKM_CTRL 129, 179, 187
0x04 TRX_CTRL_1 PA_EXT_EN IRQ_2_EXT_EN TX_AUTO_CRC_ON RX_BL_CTRL SPI_CMD_MODE IRQ_MASK_MODE IRQ_POLARITY 26, 34, 71, 97
,
165, 166, 169
0x05 PHY_TX_PWR reserved reserved reserved TX_PWR 116
0x06 PHY_RSSI RX_CRC_VALID RND_VALUE RSSI 98, 100, 151
0x07 PHY_ED_LEVEL
ED_LEVEL 103
0x08 PHY_CC_CCA CCA_REQUEST CCA_MODE CHANNEL 107, 134
0x09 CCA_THRES reserved CCA_ED_THRES 108
0x0A RX_CTRL PEL_SHIFT_VALUE reserved reserved PDT_THRES 161, 179
0x0B SFD_VALUE SFD_VALUE 171
0x0C TRX_CTRL_2 RX_SAFE_MODE reserved OQPSK_SCRAM_EN reserved OQPSK_DATA_RATE 156, 170
0x0D ANT_DIV ANT_SEL reserved ANT_DIV_EN ANT_EXT_SW_EN ANT_CTRL 161
0x0E IRQ_MASK IRQ_MASK 33
0x0F IRQ_STATUS IRQ_7_BAT_LOW IRQ_6_TRX_UR IRQ_5_AMI IRQ_4_CCA_ED_DONE
IRQ_3_TRX_END IRQ_2_RX_START IRQ_1_PLL_UNLOCK IRQ_0_PLL_LOCK 33
0x10 VREG_CTRL AVREG_EXT AVDD_OK reserved DVREG_EXT DVDD_OK reserved 122
0x11 BATMON reserved reserved BATMON_OK BATMON_HR BATMON_VTH 125
0x12 XOSC_CTRL XTAL_MODE XTAL_TRIM 130
0x13 CC_CTRL_0 CC_NUMBER 135
0x14 CC_CTRL_1 reserved CC_BAND 136
0x15 RX_SYN RX_PDT_DIS reserved RX_PDT_LEVEL 112, 157
0x16 TRX_RPC RX_RPC_CTRL RX_RPC_EN PDT_RPC_EN PLL_RPC_EN XAH_TX_RPC_EN IPAN_RPC_EN reserved 175
0x17 XAH_CTRL_1 ARET_TX_TS_EN reserved AACK_FLTR_RES_FT AACK_UPLD_RES_FT reserved AACK_ACK_TIME AACK_PROM_MODE AACK_SPC_EN 72, 88, 157,
167, 180
0x18 FTN_CTRL FTN_START reserved FTNV 139
0x19 XAH_CTRL_2 ARET_FRAME_RETRIES ARET_CSMA_RETRIES reserved 74
0x1A PLL_CF PLL_CF_START reserved reserved PLL_CF 137
0x1B PLL_DCU PLL_DCU_START reserved reserved 137
0x1C PART_NUM PART_NUM 27
0x1D VERSION_NUM VERSION_NUM 27
0x1E MAN_ID_0 MAN_ID_0 28
0x1F MAN_ID_1 MAN_ID_1 28
0x20 SHORT_ADDR_0
SHORT_ADDR_0 91
0x21 SHORT_ADDR_1
SHORT_ADDR_1 91
0x22 PAN_ID_0 PAN_ID_0 92
0x23 PAN_ID_1 PAN_ID_1 92
0x24 IEEE_ADDR_0 IEEE_ADDR_0 92
0x25 IEEE_ADDR_1 IEEE_ADDR_1 93
0x26 IEEE_ADDR_2 IEEE_ADDR_2 93
0x27 IEEE_ADDR_3 IEEE_ADDR_3 93
0x28 IEEE_ADDR_4 IEEE_ADDR_4 94
0x29 IEEE_ADDR_5 IEEE_ADDR_5 94
0x2A IEEE_ADDR_6 IEEE_ADDR_6 94
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
204
Addr
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
0x2B IEEE_ADDR_7 IEEE_ADDR_7 95
0x2C XAH_CTRL_0 MAX_FRAME_RETRIES MAX_CSMA_RETRIES
SLOTTED_OPERATION
75
0x2D CSMA_SEED_0 CSMA_SEED_0 76
0x2E CSMA_SEED_1 AACK_FVN_MODE AACK_SET_PD AACK_DIS_ACK AACK_I_AM_COORD CSMA_SEED_1 77, 90
0x2F CSMA_BE MAX_BE MIN_BE 79
0x36 TST_CTRL_DIGI
reserved reserved reserved reserved TST_CTRL_DIG 212
0x3C TST_AGC reserved AGC_HOLD_SEL AGC_RST AGC_OFF AGC_HOLD GC 113
0x3D TST_SDM MOD_SEL MOD TX_RX TX_RX_SEL reserved 138
Register Page - TOM_EN=0x01
0x3B PHY_TX_TIME reserved IRC_TX_TIME 117
Register Page - PMU_EN=0x01
0x3B
PHY_PMU_VALU
E
PMU_VALUE 188
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
205
The reset values of the Atmel AT86RF233 registers in state P_ON(1, 2, 3) are shown in
Table 14-2.
Note: All reset values in Table 14-2 are only valid after a power on reset. After a reset
procedure (/RST = L) as described in Section 7.1.4.6, the reset values of
selected registers (for example registers 0x01, 0x10, 0x11, 0x30) can differ
from that in Table 14-2.
Table 14-2. Register Summary – Reset Values.
Address Reset Value
0x00 0x00
0x01 0x00
0x02 0x00
0x03 0x09
0x04 0x22
0x05 0x00
0x06 0x60
0x07 0xFF
0x08 0x2B
0x09 0xC7
0x0A 0x37
0x0B 0xA7
0x0C 0x20
0x0D 0x00
0x0E 0x00
0x0F 0x00
Address Reset Value
0x10 0x00
0x11 0x02
0x12 0xF0
0x13 0x00
0x14 0x00
0x15 0x00
0x16 0xC1
0x17 0x00
0x18 0x58
0x19 0x00
0x1A 0x57
0x1B 0x20
0x1C 0x0B
0x1D 0x01/0x02
0x1E 0x1F
0x1F 0x00
Address Reset Value
0x20 0xFF
0x21 0xFF
0x22 0xFF
0x23 0xFF
0x24 0x00
0x25 0x00
0x26 0x00
0x27 0x00
0x28 0x00
0x29 0x00
0x2A 0x00
0x2B 0x00
0x2C 0x38
0x2D 0xEA
0x2E 0x42
0x2F 0x53
Address Reset Value
0x30 0x00
0x31 0x00
0x32 0x00
0x33 0x00
0x34 0x00
0x35 0x00
0x36 0x00
0x37 0x00
0x38 0x00
0x39 0x40
0x3A 0x00
0x3B 0x00
0x3C 0x00
0x3D 0x00
0x3E 0x00
0x3F 0x00
Notes: 1. While the reset value of register 0x10 is 0x00, any practical access to the
register is only possible when DVREG is active. So this register is always read
out as 0x04. For details, refer to Section 9.4.
2. While the reset value of register 0x11 is 0x02, any practical access to the
register is only possible when BATMON is activated. So this register is always
read out as 0x22 in P_ON state. For details, refer to Section 9.5.
3. While the reset value of register 0x30 is 0x00, any practical access to the
register is only possible when the radio transceiver is accessible. So the register
is usually read out as:
a) 0x11 after a reset in P_ON state
b) 0x07 after a reset in any other state
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
206
15 Abbreviations
AACK — Automatic Acknowledgement
ACK — Acknowledgement
ADC — Analog-to-Digital Converter
AD — Antenna Diversity
AES — Advanced Encryption Standard
AGC — Automatic Gain Control
ARET — Automatic Retransmission
AVREG — Analog Voltage Regulator
AWGN — Additive White Gaussian Noise
BATMON — Battery Monitor
BBP — Base-Band Processor
BPF — Band-Pass Filter
CBC — Cipher Block Chaining
CCA — Clear Channel Assessment
CC — Current Channel
CF — Center Frequency
CRC — Cyclic Redundancy Check
CS — Carrier Sense
CSMA-CA — Carrier Sense Multiple Access – Collision Avoidance
CW — Continuous Wave
DVREG — Digital Voltage Regulator
ECB — Electronic Code Book
ED — Energy Detect
ESD — Electrostatic discharge
EVM — Error Vector Magnitude
Fc — Channel Center Frequency
FCF — Frame Control Field
FCS — Frame Check Sequence
FIFO — First In, First Out
FTN — Filter Tuning Network
GPIO — General Purpose Input/Output
IC — Integrated Circuit
IEEE — Institute of Electrical and Electronic Engineers
IF — Intermediate Frequency
IRQ — Interrupt Request
ISM — Industrial Scientific Medical
LDO — Low Dropout
LNA — Low-Noise Amplifier
LO — Local Oscillator
LPF — Low-Pass Filter
LQI — Link Quality Indication
LSB — Least Significant Bit
MAC — Medium Access Control
MFR — MAC Footer
MHR — MAC Header
MIC — Message Integrity Code
MISO — Master Input, Slave Output
MOSI — Master Output, Slave Input
MSB — Most Significant Bit
MSDU — MAC Service Data Unit
MPDU — MAC Protocol Data Unit
MSK — Minimum Shift Keying
NOP — No Operation
O-QPSK — Offset Quadrature Phase Shift Keying
PA — Power Amplifier
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
207
PAN — Personal Area Network
PCB — Printed Circuit Board
PER — Packet Error Rate
PHR — PHY Header
PHY — Physical Layer
PLL — Phase-Looked Loop
PPDU — PHY Protocol Data Unit
PPF — Poly-Phase Filter
PRBS — Pseudo Random Binary Sequence
PSD — Power Spectrum Density
PSDU — PHY Service Data Unit
QFN — Quad Flat No-Lead Package
RF — Radio Frequency
RSSI — Received Signal Strength Indicator
RX — Receiver
SFD — Start-Of-Frame Delimiter
SHR — Synchronization Header
SPI — Serial Peripheral Interface
SRAM — Static Random Access Memory
SRD — Short Range Device
SSBF — Single Side Band Filter
TRX — Transceiver
TX — Transmitter
VCO — Voltage Controlled Oscillator
WPAN — Wireless Personal Area Network
XOSC — Crystal Oscillator
XTAL — Crystal
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
208
16 Ordering Information
Ordering Code Packaging Package Voltage Range Temperature Range
AT86RF233-ZU Tray QN 1.8V – 3.6V Industrial (-40°C to +85°C) Lead-free/Halogen-free
AT86RF233-ZUR Tape & Reel QN 1.8V – 3.6V Industrial (-40°C to +85°C) Lead-free/Halogen-free
AT86RF233-ZF Tray QN 1.8V – 3.6V Industrial (-40°C to +125°C) Lead-free/Halogen-free
AT86RF233-ZFR Tape & Reel QN 1.8V – 3.6V Industrial (-40°C to +125°C) Lead-free/Halogen-free
Package Type Description
QN 32QN2, 32-lead 5.0x5.0mm Body, 0.50mm Pitch, Quad Flat No-lead Package (QFN) Sawn
Note: T&R quantity 5,000.
Please contact your local Atmel sales office for more detailed ordering information and
minimum quantities.
17 Soldering Information
Recommended soldering profile is specified in IPC/JEDEC J-STD-.020C.
18 Package Thermal Properties
Thermal Resistance
Velocity [m/s] Theta ja [K/W]
0 40.9
1 35.7
2.5 32.0
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
209
19 Package Drawing – 32QN2
SYMBOL MIN. NOM. MAX. NOTE
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
210
Appendix A Continuous Transmission Test Mode
A.1 Overview
The Atmel AT86RF233 offers a Continuous Transmission Test Mode to support final
application / production tests as well as certification tests. Using this test mode the radio
transceiver transmits continuously a previously transferred frame (PRBS mode) or a
continuous wave signal (CW mode).
In CW mode two different signal frequencies per channel can be transmitted:
• f1[MHz] = Fc[MHz] + 0.5MHz
• f2[MHz] = Fc[MHz] - 0.5MHz
Here Fc is the channel center frequency, refer to Section 9.7.2.
Note: 1. In CW mode it is not possible to transmit a RF signal directly on the channel
center frequency.
PSDU data in the Frame Buffer must contain at least a valid PHR (see Section 8.1). It is
recommended to use a frame of maximum length (127 bytes) and arbitrary PSDU data
for the PRBS mode. The SHR and the PHR are not transmitted. The transmission starts
with the PSDU data and is repeated continuously.
A.2 Configuration
Before enabling Continuous Transmission Test Mode all register configurations shall be
done as follow:
• TX channel setting (optional)
• TX output power setting (optional)
• Mode selection (PRBS / CW)
A register access to register 0x36 and 0x1C enables the Continuous Transmission Test
Mode.
The transmission is started by enabling the PLL (TRX_CMD = PLL_ON) and writing the
TX_START command to register 0x02.
Even for CW signal transmission it is required to write valid PSDU data to the Frame
Buffer. For PRBS mode it is recommended to write a frame of maximum length.
The detailed programming sequence is shown in Table 19-1. The column R/W informs
about writing (W) or reading (R) a register or the Frame Buffer.
Table A-1. Continuous Transmission Programming Sequence.
Step Action Register R/W Value Description
1 RESET Reset AT86RF233
2 Register Access 0x0E W 0x01 Set IRQ mask register, enable
IRQ_0 (PLL_LOCK)
3 Register Access 0x04 W 0x00 Disable TX_AUTO_CRC_ON
4 Register Access 0x02 W 0x03 Set radio transceiver state
TRX_OFF
5 Register Access 0x03 W 0x01 Set clock at pin 17 (CLKM)
6 Register Access 0x08 W 0x33 Set IEEE 802.15.4 CHANNEL, for
example channel 19
7 Register Access 0x05 W 0x00 Set TX output power, for example
to PTX_MAX
8 Register Access 0x01 R 0x08 Verify TRX_OFF state
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
211
Step Action Register R/W Value Description
9 Register Access 0x36 W 0x0F Enable Continuous Transmission
Test Mode – step # 1
10(1) Register Access 0x0C W 0x03 Enable raw data mode
11(1) Register Access 0x0A W 0x37 Enable raw data mode
12(2) Frame Buffer
Write Access
W Write PSDU data (even for CW
mode), refer to Table 19-2
13 Register Access 0x1C W 0x54 Enable Continuous Transmission
Test Mode – step # 2
14 Register Access 0x1C W 0x46 Enable Continuous Transmission
Test Mode – step # 3
15 Register Access 0x02 W 0x09 Enable PLL_ON state
16 Interrupt event 0x0F R 0x01 Wait for IRQ_0 (PLL_LOCK)
17 Register Access 0x02 W 0x02 Initiate Transmission,
enter BUSY_TX state
18 Measurement Perform measurement
19 Register Access 0x1C W 0x00 Disable Continuous Transmission
Test Mode
20 RESET Reset AT86RF233
Notes: 1. Only required for CW mode, do not configure for PRBS mode.
2. Frame Buffer content varies for different modulation schemes.
The content of the Frame Buffer has to be defined for Continuous Transmission PRBS
mode or CW mode. To measure the power spectral density (PSD) mask of the
transmitter it is recommended to use a random sequence of maximum length for the
PSDU data.
To measure CW signals it is necessary to write either 0x00 or 0xFF to the Frame
Buffer, for details refer to Table 19-2.
Table A-2. Frame Buffer Content for various Continuous Transmission
Modulation Schemes.
Step Action Frame Content Comment
12 Frame Buffer
Access
Random Sequence Modulated RF signal
0x00 (each byte of PSDU) Fc – 0.5MHz, CW signal
0xFF (each byte of PSDU) Fc + 0.5MHz, CW signal
Note: 1. It is recommended to use a frame of maximum length (127 bytes).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
212
A.3 Register Description
Register 0x36 (TST_CTRL_DIGI):
The TST_CTRL_DIG register enables the continuous transmission test mode.
Figure A-1. Register TST_CTRL_DIGI.
Bit
7
6
5
4
0x36 reserved TST_CTRL_DIGI
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
Bit
3
2
1
0
0x36 TST_CTRL_DIG TST_CTRL_DIGI
Read/Write
R/W
R/W
R/W
R/W
Reset value
0
0
0
0
• Bit 3:0 - TST_CTRL_DIG
The register bits TST_CTRL_DIG with value 0xF enables continuous transmission.
Table A-3. TST_CTRL_DIG.
Register Bits Value Description
TST_CTRL_DIG 0x0 No mode is active
0xF Continuous Transmission enabled
All other values are reserved
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
213
Appendix B AT86RF233-ZF / AT86RF233-ZFR Extended Temperature Range
B.1 Introduction
Appendix B contains information specific to devices operating at temperatures up to
125°C. Only deviations to the standard device AT86RF233-ZU / AT86RF233-ZUR are
covered in this appendix, all other information are similar to previous sections when not
otherwise stated.
Performance figures for 125°C are only valid for device part numbers AT86RF233-ZF
and AT86RF233-ZFR.
B.2 Reduced Feature Set
Due to the extended temperature range AT86RF233-ZF / AT86RF233-ZFR feature set
has been reduced:
• The IEEE 802.15.4-2006 channels are supported. By contrast, the frequency range
with spacing of 500kHz is reduced from 2360MHz to 2480MHz. This replaces the
frequency range from 2322MHz to 2527MHz specified in Section 9.7 Frequency
Synthesizer (PLL). The settings of the register bits CC_BAND and CC_NUMBER
are shown in Table 19–4. Table 19–4 replaces Table 9-22.
Table B-1. Frequency Bands and Numbers.
CC_BAND CC_NUMBER Description
0x0 Not used Channels according to IEEE 802.15.4; frequency selected
by register bits CHANNEL (register 0x08, PHY_CC_CCA)
0x1, … , 0x7 0x00 – 0xFF Reserved
0x8 0x00 – 0x1F Reserved
0x8 0x6C – 0xFF 2360MHz – 2433.5MHz
Fc[MHz] = 2306[MHz] + 0.5[MHz] x CC_NUMBER
0x9 0x00 – 0x5C 2434MHz – 2480MHz.
Fc[MHz] = 2434[MHz] + 0.5[MHz] x CC_NUMBER
0x9 0xBB – 0xFF Reserved
0xA, … , 0xF 0x00 – 0xFF Reserved
• PSDU 250kb/s data rate only is supported. Section 11.3 High Data Rate Modes is
invalid
• Time-Of-Flight Module and Phase Difference Measurement are not part of the
features set. Section 11.11 and 11.12 are invalid
B.3 Electrical Characteristics
If not otherwise stated, electrical characteristics for typical operating conditions are
similar to figures provided in Electrical Characteristics in Chapter 12.
B.3.1 Recommended Operating Range
Symbol Parameter Condition Min. Typ. Max. Unit
TOP Operating temperature range -40 +25 +125 °C
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
214
B.3.2 General RF Specifications
Symbol Parameter Condition Min. Typ. Max. Unit
fRF Frequency range As specified in [1], [2] 2405 2445 2480 MHz
500kHz spacing 2360 2480 MHz
B.4 Typical Characteristics
The following charts showing each a typical behavior of the AT86RF233. These figures
are not tested during manufacturing for all supply voltages and all temperatures. All
power consumption measurements are performed with pin 17 (CLKM) disabled, unless
otherwise stated.
Power consumption for the microcontroller required to program the radio transceiver is
not included in the measurement results.
The power consumption in SLEEP and DEEP_SLEEP state mode is independent from
CLKM master clock rate selection.
The current consumption depends on several factors such as: operating voltage,
operating frequency, loading of I/O pins, switching rate of I/O pins, and ambient
temperature. The dominating factors are operating voltage and ambient temperature.
If possible the measurement results are not affected by current drawn from I/O pins.
Register, SRAM or Frame Buffer read or write accesses are not performed during
current consumption measurements.
B.4.1 Active Supply Current
The measurement setup used for the measurements is shown in Figure 5-1.
B.4.1.1 P_ON amd TRX_OFF States
Figure B-1. Current Consumption in P_ON State.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
215
Figure B-2. Current Consumption in TRX_OFF State.
B.4.1.2 PLL_ON State
Figure B-3. Current Consumption in PLL_ON State.
B.4.1.3 RX_ON State
Figure B-4. Current Consumption in RX_ON State – High Sensitivity.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
216
Figure B-5. Current Consumption in RX_ON State – High Input Level.
Figure B-6. Current Consumption in RX_ON State – Reduced Sensitivity.
B.4.1.4 TX_BUSY State
Figure B-7. Current Consumption in TX_BUSY State – Minimum Output Power.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
217
Figure B-8. Current Consumption in TX_BUSY State – Output Power 0dBm.
Figure B-9. Current Consumption in TX_BUSY State – Maximum Output Power.
B.4.1.5 SLEEP
Figure B-10. Current Consumption in SLEEP.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
218
B.4.1.6 DEEP SLEEP
Figure B-11. Current Consumption in DEEP SLEEP.
B.4.2 State Transition Timing
The measurement setup used for the measurements is shown in Figure 5-1.
Figure B-12. Transition Time from EVDD to P_ON (CLKM available).
Figure B-13. Transition Time from SLEEP to TRX_OFF (IRQ_4 (AWAKE_END)).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
219
Figure B-14. Transition Time from TRX_OFF to PLL_ON.
B.4.3 Receiver Performance
B.4.3.1 Sensitivity
Figure B-15. Sensitivity.
B.4.3.2 Adjacent & Alternate Channel Selectivity (ACRx)
Figure B-16. Adjacent and Alternate Channel Selectivity.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
220
B.4.4 Transmitter Performance
B.4.4.1 TX Output Power vs. TX Power Level
Figure B-17. TX Output Power vs. TX_PWR (EVDD = 3.0V, CH=19).
B.4.4.2 TX Output Power vs. EVDD
Figure B-18. TX Output Power vs. EVDD (TX_PWR = 0, CH=19).
B.4.4.3 TX Output Power vs. Channel
Figure B-19. TX Output Power vs. Channel (EVDD = 3.0V, TX_PWR = 0).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
221
B.4.4.4 TX EVM vs. EVDD
Figure B-20. Error Vector Magnitude (EVM) vs. EVDD (TX_PWR = 0, CH=19).
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
222
Appendix C Errata
AT86RF233 Rev. A
Potential long PLL settling duration
In very rare cases a PLL_LOCK interrupt is not generated within the specified
maximum tPLL_INIT = 250µs PLL lock duration.
Problem Fix/Workaround
In such a case perform the following action:
- read the register bits PLL_CF (register 0x1A, PLL_CF)
- invert the LSB bit
- write the value back to the PLL_CF register; keep upper four bits as
read before
- wait a additional typical tPLL_INIT = 80µs duration or until interrupt is
generated
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
223
References
[1] IEEE Standard 802.15.4™-2003: Wireless Medium Access Control (MAC) and
Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area
Networks (WPANs).
[2] IEEE Standard 802.15.4™-2006: Wireless Medium Access Control (MAC) and
Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area
Networks (WPANs).
[3] IEEE Standard 802.15.4™-2011: Low-Rate Wireless Personal Area Networks
(WPANs).
[4] ANSI/ESD STM5.1 – 2007, Electrostatic Discharge Sensitivity Testing –
Human Body Model (HBM); JESD22-A114E – 2006; CEI/IEC 60749-26 –
2006; AEC-Q100-002-Ref-D.
[5] ESD-STM5.3.1-1999: ESD Association Standard Test Method for electrostatic
discharge sensitivity testing – Charged Device Model (CDM).
[6]
NIST FIPS PUB 197: Advanced Encryption Standard (AES), Federal
Information Processing Standards Publication 197, US Department of
Commerce/NIST, November 26, 2001.
[7] AT86RF233 Software Programming Model.
MCU Wireless AT86RF233 [PRELIMINARY DATASHEET]
Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014
224
Data Sheet Revision History
Please note that revisions in this section are referring to the document revisions.
Rev. 8315E–MCU Wireless–07/14
1. Editorial updates
2. Updated the datasheet with new devices AT86RF233-ZF and AT86RF233-ZFR
(125°C extended temperature range).
3. Added Appendix B - AT86RF233-ZF / AT86RF233-ZFR Extended
Temperature Range
4. Errata moved to Appendix C.
5. Modification of RSSI base value from -91dBm to -94dBm
Rev. 8351D–MCU Wireless–08/13
1. Remove content PRELIMINARY
Rev. 8351C–MCU Wireless–02/13
1. Editorial updates
2. Update BoM Table 5-1 for Balun / Filter
3. Move Section 7.2.3.4 Frame Filtering to Section 8.2
4. Added Time-Of-Flight Module (TOM) Section 11.11
5. Added Phase Difference Measurement Section 11.12
Rev. 8351B–MCU Wireless–06/12
1. Editorial updates
2. Update RX_LISTEN description on front page
3. Update note 4 on page 159
4. Update Section 12.8 on page 168
Rev. 8351A–MCU Wireless–02/12
1. Initial release
Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 │ www.atmel.com
© 2014 Atmel Corporation. / Rev.:Atmel-8351E-MCU_Wireless-AT86RF233_Datasheet_072014.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. ARM®, ARM Connected® logo, and others are the registered trademarks or trademarks of ARM Ltd. Other terms and product names may be
trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property
right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON
THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS
PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN
NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN
IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the
contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to
update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products
are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications
where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific
written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons
systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel
products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Atmel:
AT86RF233-ZU AT86RF233-ZUR AT86RF233-ZF AT86RF233-ZFR