SRBE Encoder and Push Operation Type Switch A compact multifunctional operating device that can be utilized on the side of the set device Typical Specifications Items Specifications Ratingsmax./min. Resistive load Output voltage 1mA 5V DC/50A 3V DC Jog portion Push portion 1V max. at 1mA 5V DC Resistive load Operating forcePush portion 3.51.5N TravelPush operation Operating life 0.2mm Jog portion Push portion 100,000 cycles Product Line SRBE110301 Number of detent Number of pulse Operating direction 12 6 Horizontal Mounting method Rotational torque Jog portion Standard SRBE210200 Low-profile 1,500 6,000 1 1,300 5,200 2 Product No. SRBE110301 1,500 3,000 6,000 428x413x172 Switch Type 24 2,600 Reel size Variable Resistor Type Unit:mm Number of packagespcs. Tape width Export package mm measurementsmm 1 reel 1 case / Japan 1 case / export packing 1,300 Drawing No. 32mNm Packing Specifications Taping SRBE210200 Minimum order unitpcs. Japan Export Multi Control Devices Product No. 5,200 Refer to P.451 for soldering conditions. 445 SRBE Encoder and Push Operation Type Switch Dimensions Unit:mm No. PC board mounting hole dimensions (Viewed from direction A) Style 1 Multi Control Devices Variable Resistor Type Switch Type 2 Output SignalEncoder Circuit Diagram 446 Switch type Type SLLB5 SRBE Series SLLB Small type Photo Dimensions typical value mm W 9.5 11.8 D 8.8 11.4 H 2.2 3 Number of operating shafts Single-shaft Shaft material Resin 2-direction With Without Lever return mechanism Without With Center-push switch Encoder With With Operating temperature range Automotive use Without -10 to +60 -40 to +85 100,000 cycles 100,000 cycles Variable Resistor Type Operating life Operating life without load Operating life with load (at max. rated load) Multi Control Devices Directional resolution Directional operating feeling tactile feeling Life cycle (availability) Ratingmax.Resistive load Mechanical performance 1V max. at Measuring 1mA 5V DC circuit Resistive load Output voltage 1V max. at 1mA 5V DC Resistive load Encoder resolution 6 pluses/360 Insulation resistance 10M min. 50V DC 100M min. 100V DC Voltage proof 50V AC for 1min. 100V AC for 1min. Push operating force 0.650.3N Encoder detent torque 3.51.5N 2.51N 21N Terminal strength 32mNm Terminal strength Actuator strength Push / pull directions Operating direction Cold Environmental performance 10mA 5V DC + 5V 5K Measuring terminal 3N for 1min. 50N -30 96h 10N -20 96h Dry heat 85 96h Damp heat 40, 90 to 95%RH 96h Page Switch Type Electrical performance 1mA 5V DC 445 447 -40 96h 449 Switch Type Multi Control Devices Soldering Conditions 451 Switch Type Multi Control Devices Cautions 452 427 Switch Type / Soldering Conditions Reference for Manual Soldering Tip temperature Soldering time No. of solders RKJXT1F, RKJXM, RKJXL, SLLB, SLLB5, SRBE, SKRH Series 3505 3s max. 1 time RKJXS 35010 3 -0 s 1 2 time max. Reference for Dip Soldering Preheating Soldering surface temperature Heating time Series Dip soldering No. of solders Soldering temperature Soldering time RKJXT1F, RKJXM 100 max. 2 min. max. 2605 51s 2 time max. RKJXL 120 max. 70s max. 260 max. 6s max. 2 time max. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2 CAKor CCTat soldering portioncopper foil surface . A heat resisting tape should be used for fixed measurement. Multi Control Devices Example of Reflow Soldering Condition Variable Resistor Type 300 A B 200 C D Switch Type Temperature 3. Temperature profile 100 Times Room temperature Pre-heating E max. G max. H max. F max. I max. Series A B C D E F G H I No. of reflows RKJXS 260 230 150 150 2 min. 10s 40s 4 min. 1 time SLLB5 250 230 150 150 2 min. 30s 1 time SKRH, SLLB, SRBE 260 230 180 150 2 min. 40s 1 time Notes 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board' s temperature greatly differs from that of the switch, depending on the material, size thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. 451