CX93011-2x CSMxx V.92/V.34/V.32bis Controller Serial Modem with CX20548 SmartDAA(R) Data Sheet DSH-201689G July 2012 Revision History Revision Date Description A June 11, 2008 Initial release B July 29, 2008 Revision B release C July 31, 2008 Revision C release D June 26, 2009 Revision D release *Updated Table 1, CSMxx Models and Functions E January 20, 2011 F May 18, 2012 Revision F release *Updated package dimension tables for 16-pin QFN punch and sawn styles and 20-QFN punch and sawn styles. G July 17, 2012 Revision G release *Updated Reset description in Table 5. *Updated Figure 2 Reset section with 20 k pull-down resistor. *Updated Table 14. Revision E release *Updated Table 12, CX93011-2x Modem Operating Conditions (c) 2009, 2011, 2012, Conexant Systems, Inc. All Rights Reserved. Information in this document is provided in connection with Conexant Systems, Inc. ("Conexant") products. These materials are provided by Conexant as a service to its customers and may be used for informational purposes only. Conexant assumes no responsibility for errors or omissions in these materials. Conexant may make changes to this document at any time, without notice. Conexant advises all customers to ensure that they have the latest version of this document and to verify, before placing orders, that information being relied on is current and complete. Conexant makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Conexant's Terms and Conditions of Sale for such products, Conexant assumes no liability whatsoever. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF CONEXANT PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. CONEXANT FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. CONEXANT SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. Conexant products are not intended for use in medical, lifesaving or life sustaining applications. Conexant customers using or selling Conexant products for use in such applications do so at their own risk and agree to fully indemnify Conexant for any damages resulting from such improper use or sale. The following are trademarks of Conexant Systems, Inc.: Conexant(R) and the Conexant C symbol. Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Third-party brands and names are the property of their respective owners. For additional disclaimer information, please consult Conexant's Legal Information posted at www.conexant.com which is incorporated by reference. Conexant Lead-free products are China RoHS Compliant: Reader Response: Conexant strives to produce quality documentation and welcomes your feedback. Please send comments and suggestions to tech.pubs@conexant.com. For technical questions, contact your local Conexant sales office or field applications engineer. 2 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 Contents Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.1 1.2 1.3 1.4 1.5 2 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.1 2.2 DSH-201689G 7/17/12 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.2.1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Technical Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.3.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.3.2 Embedded MCU Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.3.3 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.3.3.1 Data/Fax Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1.3.3.2 V.44 Data Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.3.3.3 Synchronous Access Mode (SAM) - Video Conferencing . . . . . . . . . . . . . . 16 1.3.3.4 TAM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.3.3.5 Worldwide Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1.3.4 Reference Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1.4.1 CX93011-2x Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1.4.2 Digital Isolation Barrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1.4.3 CX20548 SmartDAA Line Side Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 1.5.1 Data Modem Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Serial DTE Interface Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.1.1 Automatic Speed/Format Sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.1.1.1 Command Mode and Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Establishing Data Modem Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.1 Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.1.1 DTMF Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.1.2 Pulse Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.1.3 Blind Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.2 Modem Handshaking Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.3 Call Progress Tone Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.4 Answer Tone Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 (c) 2012 Conexant Systems, Inc. 3 CX93011-2x CSMxx Data Sheet 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 4 2.2.5 Ring Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.6 Billing Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.2.7 Connection Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.2.8 Automode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Data Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.1 Speed Buffering (Normal Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.2 Flow Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.3 Escape Sequence Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.4 BREAK Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.5 Telephone Line Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.5.1 GSTN Cleardown (V.92, V.90, V.34, V.32bis, V.32). . . . . . . . . . . . . . . . . . . . 26 2.3.5.2 Loss of Carrier (V.22bis and Below). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.3.6 Fall Forward/Fallback (V.92/V.90/V.34/V.32bis/V.32) . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.7 Retrain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.8 Programmable Inactivity Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.9 DTE Signal Monitoring (Serial DTE Interface Only) . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.9.1 DTR# . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.9.2 RTS# . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.10 Call Progress Speaker Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.3.11 Serial EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 V.92 Features (V.92 Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.1 Modem-on-Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.2 Quick Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.3 PCM Upstream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Error Correction and Data Compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.5.1 V.42 Error Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.5.2 MNP 2-4 Error Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.5.3 V.44 Data Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.5.4 V.42bis Data Compression. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.5.5 MNP 5 Data Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Voice/Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.1 Online Voice Command Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.2 Voice Receive Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.3 Voice Transmit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.4 Full-Duplex Receive and Transmit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.5 Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2.6.6 Tone Detectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 V.80 Synchronous Access Mode (SAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Telephony Extensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.8.1 Line-in-Use Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.8.2 Extension Pick-up Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.8.3 Remote Hang-up Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Point-of-Sales Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Fax Class 1, Fax Class 1.0, and Fax Class 2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Tone Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Call Waiting Tone Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.14 2.15 Worldwide Country Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.15.1 Analog Loopback (&T1 Command).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.15.2 Analog Loopback (&T1 Command).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.16 Low Power Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.16.1 Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.16.2 Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.16.3 Deep Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 2.16.4 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 3 Hardware Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1 3.2 3.3 3.4 CX93011-2x Modem Hardware Interface Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1 CX93011-2x Modem Interface Signal Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1.1 LSD Interface (Through DIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1.2 Call Progress Speaker Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1.3 Clock Select Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1.4 Serial EEPROM Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.1.5 Serial DTE Interface and Indicator Outputs . . . . . . . . . . . . . . . . . . . . . . . . . 35 3.1.2 CX93011-2x Modem Pin Assignments and Signal Definitions. . . . . . . . . . . . . . . . . . 36 3.1.3 CX93011-2x Modem Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CX20548 LSD Hardware Pins and Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.1.1 Host Side Device (HSD) Interface (Through DIB) . . . . . . . . . . . . . . . . . . . . 41 3.2.1.2 Power and Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.1.3 Telephone Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.1.4 Voltage References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.1.5 General Purpose Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.2.2 Pin Assignments and Signal Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Operating Conditions, Absolute Maximum Ratings, and Power Requirements . . . . . . . . . . 47 3.3.1 Handling CMOS Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Crystal and Clock Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 4 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 5 Recommended QFN Surface Mount Land Patterns . . . . . . . . . . . . . . . . . . . . . . 57 DSH-201689G 7/17/12 (c) 2012 Conexant Systems, Inc. 5 CX93011-2x CSMxx Data Sheet 6 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. DSH-201689G 7/17/12 CSMxx Modem Simplified Interface Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 CX93011-2x Modem Hardware Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 CX93011-2x Modem 20-Pin QFN Pin Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 CX20548 LSD Hardware Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 CX20548 LSD 16-Pin QFN Pin Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Package Dimensions for 20-Pin QFN, Punch Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Package Dimensions for 20-Pin QFN, Sawn Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Package Dimensions for 16-Pin QFN, Punch Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Package Dimensions for 16-Pin QFN, Sawn Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Recommended Surface Mount Land Pattern for 20-Pin QFN . . . . . . . . . . . . . . . . . . . . 57 Recommended Surface Mount Land Pattern for 16-Pin QFN . . . . . . . . . . . . . . . . . . . . . 58 (c) 2012 Conexant Systems, Inc. 7 CX93011-2x CSMxx Data Sheet 8 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. DSH-201689G 7/17/12 CSMxx Models and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Default Countries Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 +MS Command Automode Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 CX93011-2x Modem 20-Pin QFN Pin Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 CX93011-2x Modem 20-Pin QFN Pin Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 CX93011-2x Modem I/O Type Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CX93011-2x Modem DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 CX20548 LSD 16-Pin QFN Pin Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 CX20548 LSD Hardware Signal Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 CX20548 LSD GPIO DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 CX20548 LSD AVDD and DVDD DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . 46 CX93011-2x Modem Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 CX93011-2x Current and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Crystal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Clock Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Package Dimensions for 20-Pin Punch and Sawn Styles . . . . . . . . . . . . . . . . . . . . . . . . 51 Package Dimensions for 16-Pin Punch and Sawn Styles . . . . . . . . . . . . . . . . . . . . . . . . 54 (c) 2012 Conexant Systems, Inc. 9 Tables 10 CX93011-2x CSMxx Data Sheet (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 1 1.1 Introduction Overview The Conexant(R) CSMxx V.92 Modem supports V.92 analog data modem operation and 14.4 kbps fax modem operation. In addition, the modem supports remote telephone answering machine (TAM). The modem also supports V.44/V.42bis/MNP 5 data compression for greater data throughput and V.42 LAPM/MNP2-4 error correction protocol for increased data integrity and reliability. Table 1 lists the ordering information. The CSMxx device set consists of a CX93011-2x V.92/V.34/V.32bis Modem device in a 20-pin QFN and a CX20548 SmartDAA(R) 4 Line Side Device (LSD) in a 16-pin QPN. The CX93011-2x has a serial interface. The CX93011-2x modem device integrates a microcontroller (MCU), a digital signal processor (DSP), internal RAM, internal ROM, and a SmartDAA system side device (SSD) onto a 20-pin QFN.Figure 1 illustrates the top-level modem interface connection. Conexant's SmartDAA technology used in the SmartDAA 4 LSD eliminates the need for bulky analog transformers, relays, and opto-isolators typically used in discrete DAA implementations. The SmartDAA 4 LSD operates without drawing power from the phone line, unlike line-powered DAAs, and is therefore not subject to variations in line voltage conditions. The SmartDAA 4 LSD also adds enhanced telephony extension features to the modem's operation and other functions such as Call Waiting detection, and Caller ID decoding. Incorporating Conexant's proprietary Digital Isolation Barrier (DIB) design and other innovative DAA features, the SmartDAA architecture simplifies application design and minimizes layout area to reduce design cost. In TAM mode, enhanced 2-bit or 4-bit per sample coding schemes at 8 kHz sample rate provide flexible format compatibility and allows efficient digital storage of voice/ audio. Also supported are 8-bit A-law, -law, and linear coding and IMA 4-bit ADPCM coding. This mode supports applications such as digital telephone answering machine, voice annotation, and recording from and playback to the telephone line. The modem operates by executing masked code from internal ROM. The modem features internal RAM memory that enhances the modem's flexibility. The modem's internal RAM can be used to load new country profiles, override existing country profiles or add customized firmware code. An optional external serial NVRAM is supported. The optional external NVRAM adds the convenience of permanent storage, just like internal RAM, NVRAM can be used to store new country profiles, override existing ones or add customized firmware code. Small, low-profile packages, reduced voltage operation, and low power consumption make this device set an ideal solution for embedded applications. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 11 Introduction Table 1. CX93011-2x CSMxx Data Sheet CSMxx Models and Functions Model/Order/Part Numbers Supported Functions V.34 Data V.32bis Data, V.17 Fax, TAM, Worldwide Y Y Y CX20548-11Z (Note 3) -- Y Y CX20548-11Z (Note 3) -- -- Y Marketing Name Device Set Order Number Modem Device (20-Pin QFN) Part Number Line Side Device (LSD) V.92/V90 (16-Pin QFN) Data Part Number CSM92 DS92-CSM-21Z CX93011-21Z CX20548-11Z (Note 3) CSM34 DS34-CSM-22Z CX93011-22Z CSM32bis DS32-CSM-23Z CX93011-23Z GENERAL NOTES: 1. Supported functions (Y = Supported; N = Not supported). 2. All devices are lead-free (Pb-free) and RoHS-compliant. These devices are compatible with leaded reflow processes. 3. Device is marked 20548-A. Figure 1. CSMxx Modem Simplified Interface Diagram DAA Hardware CX93011-2x Modem 20-Pin QFN Serial Interface ROM CX20548 SmartDAA 4 Line Side Device (LSD) 16-Pin QFN Telephone Line DTE/Host Interface RAM 12 28.224 MHz or 27.000 MHz Crystal or Clock Source Digital Isolation Barrier (DIB) MCU/DSP SmartDAA Interface Line Side DIB Interface (LSDI) Codec Telephone Line Interface External Discrete Components TIP RING Optional NVRAM Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 1.2 Introduction Features Modulations and protocols - ITU-T V.92 (V.92 model) Modem-on-Hold (MOH) Quick connect (QC) PCM upstream - V.90 (V.92 model) - V.34 (V.92 and V.34 models) - V.32bis, V.32, V.22bis, V.22, V.23, V.21 - V.23 reverse, V.23 half-duplex - Bell 212A/Bell 103 - V.29 FastPOS - V.22bis fast connect - V.80 Synchronous Access Mode Data compression and error correction - V.44 data compression (V.92 model) - V.42bis and MNP 5 data compression - V.42 LAPM and MNP 2-4 error correction Fax modem send and receive rates up to 14.4 kbps - V.17, V.29, V.27 ter, and V.21 channel 2 - EIA/TIA 578 Class 1, T.31 Class 1.0, and Class 2 Call Waiting (CW) detection and Type II Caller ID decoding during data mode Type I Caller ID (CID) decoding Telephony/TAM - V.253 commands - 2-bit and 4-bit ADPCM, 4-bit IMA ADPCM, 8-bit and 16-bit linear PCM, and 8bit -law and A-law PCM coding - 8 kHz sample rate - Concurrent DTMF, ring, and Caller ID detection DTE/host interface - Serial DTE interface - Direct Mode - Asynchronous Mode No external memory required Sixty-three embedded and upgradeable country profiles Serial NVRAM interface for optional permanent country profile storage Embedded AT commands DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 13 Introduction CX93011-2x CSMxx Data Sheet SmartDAA - Extension pick-up detection - Digital line protection - Line reversal detection - Line-in-use detection - Remote hang-up detection - Worldwide compliance Selectable 28.224 MHz or 27.000 MHz frequency of operation Low power and voltage - Single +3.3V supply - Low power consumption mode - +3.3V I/O level Compact, robust board design - Small, low-profile modem packages - SmartDAA and DIB technologies - Reference design supports 5 kV isolation Small packages - CX93011-2x Modem: 20-pin QFN - CX20548 LSD: 16-pin QFN 1.2.1 Applications Set top boxes Point-of-Sale terminals ATM machines Metering terminals Video game consoles Internet appliances 14 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Introduction 1.3 Technical Overview 1.3.1 General Description Modem operation, including dialing, call progress, telephone line interface, telephone handset interface, and host DTE interface functions are supported and controlled through the V.250 and V.253-compatible command set. The OEM adds a crystal circuit, DIB components, telephone line interface, telephone handset/telephony extension interface, and other supporting discrete components as supported by the modem model (Table 1) and required by the application to complete the system. 1.3.2 Embedded MCU Firmware Embedded MCU firmware performs processing of general modem control, command sets, data modem, error correction and data compression (ECC), worldwide, V.80, and serial DTE host interface functions according to modem models (Table 2). 1.3.3 Operating Modes 1.3.3.1 Data/Fax Modes Data modem modes perform complete handshake and data rate negotiations. Using modem modulations to optimize modem configuration for line conditions, the modem can connect at the highest data rate that the channel can support from 56 kbps down to 2400 bps with automatic fallback. In V.92 data modem mode (V.92 model), the modem can receive data from a digital source using a V.92-compatible central site modem at line speeds up to 56 kbps. With PCM upstream enabled, data transmission supports sending data at line speeds up to 48 kbps. When PCM upstream is disabled, data transmission supports sending data at line speeds up to V.34 rates. This mode can fallback to V.34 mode and to lower rates as dictated by line conditions. The following modes in V.92 models are also supported when connected to a V.92compatible server supporting the feature listed. Quick connect, which allows quicker subsequent connection to a server using stored line parameters obtained during the initial connection. The server must support quick connect profiles. Modem-on-Hold, which allows detection and reporting of incoming phone calls on the PSTN with enabled Call Waiting. If the incoming call is accepted by the user, the user has a pre-defined amount of time of holding the data connection for a brief conversation. The data connection resumes upon incoming call termination. The server must support Modem-on-Hold functionality. PCM upstream, which boosts the upstream data rates between the user and V.92 server. A maximum of 48 kbps upstream rate is supported when connected to a V.92 server that supports PCM upstream. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 15 Introduction CX93011-2x CSMxx Data Sheet In V.34 data modem mode (V.92 and V.34 models), the modem can operate in 2-wire, full-duplex, asynchronous modes at line rates up to 33.6 kbps. Data modem modes perform complete handshake and data rate negotiations. Using V.34 modulation to optimize modem configuration for line conditions, the modem can connect at the highest data rate that the channel can support from 33600 bps down to 2400 bps with automatic fallback. Automode operation in V.34 is provided in accordance with PN3320 and in V.32bis in accordance with PN2330. All tone and pattern detection functions required by the applicable ITU or Bell standards are supported. In V.32bis data modem mode, the modem can operate at line speeds up to 14.4 kbps. In fax modem mode, the modem can operate in 2-wire, half-duplex, synchronous modes and can support Group 3 facsimile send and receive speeds of 14400, 12000, 9600, 7200, 4800, and 2400 bps. Fax data transmission and reception performed by the modem are controlled and monitored through the EIA/TIA-578 Fax Class 1, T.31 Fax Class 1.0, or Fax Class 2 command interface. Full HDLC formatting, zero insertion/deletion, and CRC generation/checking are provided. 1.3.3.2 V.44 Data Compression V.44 provides more efficient data compression than V.42bis that significantly decreases the download time for the types of files associated with Internet use. This significant improvement is most noticeable when browsing and searching the web since HTML text files are highly compressible. (The improved performance amount varies both with the actual format and with the content of individual pages and files.) 1.3.3.3 Synchronous Access Mode (SAM) - Video Conferencing V.80 Synchronous Access Mode between the modem and the host/DTE is provided for host-controlled communication protocols, e.g., H.324 video conferencing applications. 1.3.3.4 TAM Mode TAM Mode features include 2-bit/4-bit ADPCM, 4-bit IMA ADPCM, 8-bit and 16-bit linear PCM, and 8-bit -law and A-law PCM coding at 8 kHz sample rate. Tone detection/ generation, call discrimination, and concurrent DTMF detection are also supported. TAM Mode is supported by four submodes: Online Voice Command Mode supports connection to the telephone line. Voice Receive Mode supports recording voice or audio data input from the telephone line. Voice Transmit Mode supports playback of voice or audio data to the telephone line. Full-duplex Receive and Transmit Mode 1.3.3.5 Worldwide Operation The modem operates in TBR21-compliant and other countries. Country-dependent modem parameters for functions such as dialing, carrier transmit level, calling tone, call progress tone detection, answer tone detection, blacklisting, caller ID, and relay control are programmable. SmartDAA technology allows a single PCB design and 16 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Introduction single BOM to be homologated worldwide. Advanced features such as extension pickup detection, remote hang-up detection, line-in-use detection, and digital PBX line protection are supported. Country code IDs are defined by ITU-T T.35. Internal ROM includes default profiles for 63 countries including TBR21-compliant profiles. An additional or modified country profile can be loaded into internal SRAM. A duplicate country profile stored in internal SRAM will override the profile in internal ROM firmware. Additional country profiles can be loaded into external NVRAM for permanent storage. The default countries supported are listed in Table 2. Request additional country profiles from a Conexant Sales Office. Table 2. Default Countries Supported (1 of 3) Country Code Call Waiting Tone Detection (CW) Supported Argentina 7 X Australia 9 X X X Austria 0A X X X Belgium 0F X X Brazil 16 X X Bulgaria 1B X X Canada 20 X Chile 25 X China 26 X Columbia 27 X X Croatia FA X X Cyprus 2D X X Czech Republic 2E X X Denmark 31 X Egypt 36 X X Estonia F9 X X Finland 3C X X X France 3D X X X Germany 42 X X X Greece 46 X Country DSH-201689G 7/17/12 On-Hook Type 1 Caller ID (CID) Supported Conexant Conexant Proprietary and Confidential Off-Hook Type 2 Caller ID (CID2) Supported X X X X X X X X X 17 Introduction Table 2. CX93011-2x CSMxx Data Sheet Default Countries Supported (2 of 3) Country Code Call Waiting Tone Detection (CW) Supported On-Hook Type 1 Caller ID (CID) Supported Off-Hook Type 2 Caller ID (CID2) Supported Hong Kong 50 X X X Hungary 51 X X Iceland 52 X X India 53 X Indonesia 54 X Ireland 57 X Israel 58 X Italy 59 X X X Japan 00 X X X Korea 61 X X X Kuwait 62 X X Lebanon 64 X X Luxembourg 69 X X Malaysia 6C X X Mexico 73 X X Morocco 77 X X Netherlands 7B X X X New Zealand 7E X X X Norway 82 X X X Pakistan 84 X X Philippines 89 X X Poland 8A X X Portugal 8B X X Romania 8E X X Russia B8 X X Saudi Arabia 98 X X Senegal 99 X X Conexant DSH-201689G Country 18 Conexant Proprietary and Confidential X X X X X X 7/17/12 CX93011-2x CSMxx Data Sheet Table 2. Introduction Default Countries Supported (3 of 3) Country Code Call Waiting Tone Detection (CW) Supported On-Hook Type 1 Caller ID (CID) Supported Off-Hook Type 2 Caller ID (CID2) Supported Singapore 9C X X X Slovakia FB X X Slovenia FC X X South Africa 9F X X Spain A0 X Sri Lanka A1 X Sweden A5 X Switzerland A6 X Taiwan FE X Thailand A9 X X Tunisia AD X X Turkey AE X X United Kingdom B4 X United Arab Emirates B3 X X Uruguay B7 X X USA 85 X Reserved FD Country 1.3.4 X X X X X X X X X X X X Reference Designs A reference design consisting of a motherboard and daughtercard set is available to minimize modem design time, reduce development cost, and accelerate market entry. The part numbers for this design are: CX-9Z-C00217 (motherboard) and CX-9ZC00218 (daughtercard). A reference modem user's guide (USG-201664) is available in electronic form. This user's guide includes schematics, bill of materials (BOM), vendor part list (VPL), board layout files, and complete documentation. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 19 Introduction CX93011-2x CSMxx Data Sheet 1.4 Hardware Description 1.4.1 CX93011-2x Modem The CX93011-2x modem includes a Microcontroller (MCU), a Modem Data Pump (MDP), internal ROM, internal RAM, and SmartDAA interface functions. The modem connects to host via a logical V.24 (EIA/TIA-232-E) serial DTE interface. The modem MCU/DSP performs the command processing, host interface functions and telephone line signal modulation/demodulation which reduces computational load on the host processor. The SmartDAA Interface communicates with, and supplies power and clock to the LSD through the DIB. 1.4.2 Digital Isolation Barrier The OEM-supplied Digital Isolation Barrier (DIB) electrically DC isolates the CX930112x from the LSD and telephone line. The modem is connected to a fixed digital ground and operates with standard CMOS logic levels. The LSD is connected to a floating ground and can tolerate high voltage input (compatible with telephone line and typical surge requirements). The DIB transformer couples power and clock from the CX93011-2x to the LSD. The DIB data channel supports bidirectional half-duplex serial transfer of data, control, and status information between the CX93011-2x and the LSD over two lines. 1.4.3 CX20548 SmartDAA Line Side Device The CX20548 SmartDAA 4 Line Side Device (LSD) includes a Line Side DIB Interface, a coder/decoder (codec), and a Telephone Line Interface (TLI). The Line Side DIB Interface communicates with, and receives power and clock from, the SmartDAA 4 interface in the host side device (HSD) through the DIB transformer. The clock signal passing through the transformer is rectified in the LSD and filtered using external capacitors. Information is transferred between the LSD and the HSD through the DIB transformer using pulse width modulation. The TLI integrates DAA and direct telephone line interface functions and connects directly to the line TIP and RING pins, as well as to external line protection components. Direct LSD connection to TIP and RING allows real-time measurement of telephone line parameters, such as the telephone central office (CO) battery voltage, individual telephone line (copper wire) resistance, and allows dynamic regulation of the off-hook TIP and RING voltage and total current drawn from the central office (CO). This allows the modem to maintain compliance with U.S. and worldwide regulations. 20 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 1.5 Introduction Commands The modem supports data modem and V.80 commands, and S Registers in accordance with modem model options. See Doc. REM-201692 for a description of the commands. 1.5.1 Data Modem Operation Data modem functions operate in response to the AT commands when +FCLASS=0. Default parameters support U.S./Canada operation. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 21 Introduction 22 CX93011-2x CSMxx Data Sheet Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 2 Technical Specifications 2.1 Serial DTE Interface Operation 2.1.1 Automatic Speed/Format Sensing 2.1.1.1 Command Mode and Data Mode The modem can automatically determine the speed and format of the data sent from the DTE. The modem can sense speeds of 300, 600, 1200, 2400, 4800, 7200, 9600, 12000, 14400, 16800, 19200, 21600, 24000, 26400, 28800, 38400, 57600, and 115200 bps and the following data formats: Parity Data Length (Number of Bits) Number of Stop Bits Character Length (Number of bits) None 7 2 10 Odd 7 1 10 Even 7 1 10 None 8 1 10 Odd 8 1 11(1) Even 8 1 11(1) FOOTNOTES: (1) 11-bit characters are sensed, but the parity bit is stripped off during data transmission in Normal and Error Correction modes. The modem can speed sense data with mark or space parity and configures itself as follows: DSH-201689G 7/17/12 DTE Configuration Modem Configuration 7 mark 7 none 7 space 8 none 8 mark 8 none 8 space 8 even Conexant Conexant Proprietary and Confidential 23 Technical Specifications CX93011-2x CSMxx Data Sheet 2.2 Establishing Data Modem Connections 2.2.1 Dialing 2.2.1.1 DTMF Dialing DTMF dialing using DTMF tone pairs is supported in accordance with ITU-T Q.23. 2.2.1.2 Pulse Dialing Pulse dialing is supported in accordance with EIA/TIA-496-A. 2.2.1.3 Blind Dialing The modem can blind dial in the absence of a dial tone if enabled by the X0, X1, or X3 command. 2.2.2 Modem Handshaking Protocol If a tone is not detected within the time specified in the S7 register after the last digit is dialed, the modem aborts the call attempt. 2.2.3 Call Progress Tone Detection Ringback, equipment busy, congested tone, warble tone, and progress tones can be detected in accordance with the applicable standard. 2.2.4 Answer Tone Detection Answer tone can be detected over the frequency range of 2100 40 Hz in ITU-T modes and 2225 40 Hz in Bell modes. 2.2.5 Ring Detection A ring signal can be detected from a TTL-compatible 15.3 Hz to 68 Hz square wave input. 2.2.6 Billing Protection When the modem goes off-hook to answer an incoming call, both transmission and reception of data are prevented for 2 seconds to allow transmission of the billing tone signal. 24 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.2.7 Technical Specifications Connection Speeds The modem functions as a data modem when the +FCLASS=0 command is active. Line connection can be selected using the +MS command. The +MS command selects modulation, enables/disables automode, and selects minimum and maximum line speeds (Table 3). Table 3. +MS Command Automode Connectivity Modulation Possible (<min_rx_rate>, <min_rx_rate>, (<min_tx_rate>), and <max_tx_rate>) Rates (bps) <carrier> Bell 103 B103 300 Bell 212 B212 1200 Rx/75 Tx or 75 Rx/1200 Tx V.21 V21 300 V.22 V22 1200 V.22bis V22B 2400 or 1200 V.23 V23C 1200 V.32 V32 9600 or 4800 V.32bis V32B 14400, 12000, 9600, 7200, or 4800 V.34/V.90 upstream(1) V34/V90 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600, 7200, 4800, or 2400 V.90 downstream(2) V90 56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000 V.92 downstream(2) V92 56000, 54667, 53333, 52000, 50667, 49333, 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000 V.92 upstream(2) V92 48000, 46667, 45333, 44000, 42667, 41333, 40000, 38667, 37333, 36000, 34667, 33333, 32000, 30667, 29333, 28000, 26667, 25333, 24000 FOOTNOTES: V.92 and V.34 models. (2) V.92 models (1) 2.2.8 Automode Automode detection can be enabled by the +MS command to allow the modem to connect to a remote modem in accordance with draft PN-3320 for V.34 (Table 3). DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 25 Technical Specifications 2.3 CX93011-2x CSMxx Data Sheet Data Mode Data mode exists when a telephone line connection has been established between modems and all handshaking has been completed. 2.3.1 Speed Buffering (Normal Mode) Speed buffering allows a DTE to send data to, and receive data from, a modem at a speed different than the line speed. The modem supports speed buffering at all line speeds. 2.3.2 Flow Control DTE-to-Modem Flow Control. If the modem-to-line speed is less than the DTE-tomodem speed, the modem supports XOFF/XON or RTS/CTS flow control with the DTE to ensure data integrity. 2.3.3 Escape Sequence Detection The +++ escape sequence can be used to return control to the command mode from the data mode. Escape sequence detection is disabled by an S2 Register value greater than 127. 2.3.4 BREAK Detection The modem can detect a BREAK signal from either the DTE or the remote modem. The \Kn command determines the modem response to a received BREAK signal. 2.3.5 Telephone Line Monitoring 2.3.5.1 GSTN Cleardown (V.92, V.90, V.34, V.32bis, V.32). Upon receiving GSTN Cleardown from the remote modem in a non-error correcting mode, the modem cleanly terminates the call. 2.3.5.2 Loss of Carrier (V.22bis and Below). If carrier is lost for a time greater than specified by the S10 register, the modem disconnects. 26 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.3.6 Technical Specifications Fall Forward/Fallback (V.92/V.90/V.34/V.32bis/V.32) During initial handshake, the modem will fallback to the optimal line connection within V.92/V.90/V.34/V.32bis/V.32 mode depending upon signal quality if automode is enabled by the +MS or N1 command. When connected in V.92/V.90/V.34/V.32bis/V.32 mode, the modem will fall forward or fallback to the optimal line speed within the current modulation depending upon signal quality if fall forward/fallback is enabled by the%E2 command. 2.3.7 Retrain The modem may lose synchronization with the received line signal under poor or changing line conditions. If this occurs, retraining may be initiated to attempt recovery depending on the type of connection. The modem initiates a retrain if line quality becomes unacceptable if enabled by the %E command. The modem continues to retrain until an acceptable connection is achieved, or until 30 seconds elapse resulting in line disconnect. 2.3.8 Programmable Inactivity Timer The modem disconnects from the line if data is not sent or received for a specified length of time. In normal or error-correction mode, this inactivity timer is reset when data is received from either the DTE or from the line. This timer can be set to a value between 0 and 255 seconds by using register S30. A value of 0 disables the inactivity timer. 2.3.9 DTE Signal Monitoring (Serial DTE Interface Only) 2.3.9.1 DTR# When DTR# is asserted, the modem responds in accordance with the &Dn and &Qn commands. 2.3.9.2 RTS# RTS# is used for flow control if enabled by the &K command in normal or errorcorrection mode. 2.3.10 Call Progress Speaker Interface A digital speaker output (DSPKOUT) is supported. DSPKOUT is a square wave output in Data mode used for call progress or carrier monitoring. This output can be optionally connected to a low-cost on-board speaker, e.g., a sounducer, or to an analog speaker circuit. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 27 Technical Specifications 2.3.11 CX93011-2x CSMxx Data Sheet Serial EEPROM Interface The 20-pin QFN supports a 2-line serial interface to an optional serial EEPROM. The EEPROM can hold information such as firmware customization, and country code parameters. Data stored in EEPROM takes precedence over the factory default settings. A serial EEPROM is required only if additional storage is required for more country profiles or customized firmware code. The EEPROM size can range from 2 Kb (256 x 8) to 256 Kb (32K x 8) and must support a clock frequency of at least 400 kHz. For overriding, adding new country profiles, or loading NVRAM patches, the EEPROM size must be larger than 2Kb. The size of the EEPROM device will depend on the number of country profiles added or patch size. 2.4 V.92 Features (V.92 Model) Modem-on-Hold, quick connect, and PCM upstream are only available when connecting in V.92 data mode. V.92 features are only available when the server called is a V.92 server that supports that particular feature. 2.4.1 Modem-on-Hold The Modem-on-Hold (MOH) function enables the modem to place an Internet data connection on hold while using the same line to accept an incoming or place an outgoing voice call. This feature is available only with a connection to a server supporting MOH. MOH can be executed through either of two methods: One method is to enable MOH through the +PMH command. With Call Waiting Detection (+PCW command) enabled, an incoming call can be detected while online. Using a string of commands, the modem negotiates with the server to place the data connection on hold while the line is released so that it can be used to conduct a voice call. Once the voice call is completed, the modem can quickly renegotiate with the server back to the original data call. An alternative method is to use communications software that makes use of the Conexant Modem-on-Hold drivers. Using this method, the software can detect an incoming call, place the data connection on hold, and switch back to a data connection. 2.4.2 Quick Connect The quick connect function enables the modem to shorten the connect time of subsequent calls to a server supporting quick connect. The quick connect feature is supported by the +PQC command. 28 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.4.3 Technical Specifications PCM Upstream PCM upstream boosts the upstream data rates between the user and ISP to reduce upload times for large files and e-mail attachments. A maximum of 48 kbps upstream rate is supported with PCM upstream enabled, in contrast to a maximum of 32.2 kbps upstream rate with PCM upstream not enabled. PCM upstream is supported by the +PCM command. PCM upstream is disabled by default. 2.5 Error Correction and Data Compression 2.5.1 V.42 Error Correction V.42 supports two methods of error correction: LAPM and, as a fallback, MNP 4. The modem provides a detection and negotiation technique for determining and establishing the best method of error correction between two modems. 2.5.2 MNP 2-4 Error Correction MNP 2-4 is a data link protocol that uses error correction algorithms to ensure data integrity. Supporting stream mode, the modem sends data frames in varying lengths depending on the amount of time between characters coming from the DTE. 2.5.3 V.44 Data Compression V.44 data compression encodes pages and files associated with Web pages more efficiently than V.42bis. These files include WEB pages, graphics and image files, and document files. V.44 can provide an effective data throughput rate up to DTE rate for a 56-kbps connection. The improved performance amount varies both with the actual format and with the content of individual pages and files. 2.5.4 V.42bis Data Compression V.42bis data compression mode, enabled by the %Cn command or S46 register, operates when a LAPM connection is established. The V.42bis data compression employs a "string learning" algorithm in which a string of characters from the DTE is encoded as a fixed length codeword and stored in a dictionary. The dictionary is dynamically updated during normal operation. 2.5.5 MNP 5 Data Compression MNP 5 data compression mode, enabled by the %Cn command, operates during an MNP connection. In MNP 5, the modem increases its throughput by compressing data into tokens before transmitting it to the remote modem, and by decompressing encoded received data before sending it to the DTE. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 29 Technical Specifications 2.6 CX93011-2x CSMxx Data Sheet Voice/Audio Mode Voice and audio functions are supported by the Voice Mode. Voice Mode includes four submodes: Online Voice Command Mode, Voice Receive Mode, Voice Transmit Mode and Full-Duplex Receive and Transmit Mode. 2.6.1 Online Voice Command Mode This mode results from the connection to the telephone line or a voice/audio I/O device (e.g., microphone, speaker, or handset) through the use of the +FCLASS=8 and +VLS commands. After mode entry, AT commands can be entered without aborting the connection. 2.6.2 Voice Receive Mode This mode is entered when the +VRX command is active in order to record voice or audio data input at the RIN pin, typically from a microphone/handset or the telephone line. Received analog voice samples are converted to digital form and compressed for reading by the host. AT commands control the codec bits-per-sample rate. Received analog mono audio samples are converted to digital form and formatted into 8-bit unsigned linear PCM format for reading by the host. AT commands control the bit length and sampling rate. Concurrent DTMF/tone detection is available at the 8 kHz sample rate. 2.6.3 Voice Transmit Mode This mode is entered when the +VTX command is active in order to playback voice or audio data to the TXA output, typically to a speaker/handset or to the telephone line. Digitized voice data is decompressed and converted to analog form at the original compression quantization sample-per-bits rate then output to the TXA output. Digitized audio data is converted to analog form then output to the TXA output. 2.6.4 Full-Duplex Receive and Transmit Mode This mode is entered when the +VTR command is active in order to concurrently receive and transmit voice. 2.6.5 Audio Mode The audio mode enables the host to transmit and receive 8-bit audio signals. In this mode, the modem directly accesses the internal analog-to-digital (A/D) converter (ADC) and the digital-to-analog (D/A) converter (DAC). Incoming analog audio signals can then be converted to digital format and digital signals can be converted to analog audio output. 30 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.6.6 Technical Specifications Tone Detectors The tone detector signal path is separate from the main received signal path thus enabling tone detection to be independent of the configuration status. In Tone Mode, all three tone detectors are operational. 2.7 V.80 Synchronous Access Mode (SAM) V.80 Synchronous Access Mode between the modem and the host/DTE is provided for host-controlled communication protocols, e.g., H.324 video conferencing applications. Voice-call-first (VCF) before switching to a videophone call is also supported. 2.8 Telephony Extensions The following telephony extension features are supported and are typically implemented in designs for set-top box applications to enhance end-user experience: Line-in-use detection Extension pick-up detection Remote hang-up detection The telephony extension features are enabled through the -STE command. The -TTE command can be used to adjust the voltage thresholds for the telephony extension features. 2.8.1 Line-in-Use Detection The line-in-use detection feature can stop the modem from disturbing the phone line when the line is already being used. When an attempt is made to dial using ATDT and the phone line is in use, the modem will not go off hook and will respond with the message "LINE IN USE". 2.8.2 Extension Pick-up Detection The extension pick-up detection feature (also commonly referred as PPD or Parallel phone detection) allows the modem to detect when another telephony device (i.e., fax machine, phone, satellite/cable box) is attempting to use the phone line. When an extension pick-up has been detected, the modem will go on-hook and respond with the message "OFF-HOOK INTRUSION". This feature can be used to quickly drop a modem connection in the event when a user picks up an extension phone line. For example, this feature allows set top boxes with an integrated CSMxx modem to give normal voice users the highest priority over the telephone line. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 31 Technical Specifications 2.8.3 CX93011-2x CSMxx Data Sheet Remote Hang-up Detection The remote hang-up detection feature will cause the modem to go back on-hook and respond with the message "LINE REVERSAL DETECTED" during a data connection when the remote modem is disconnected for abnormal termination reasons (remote phone line unplugged, remote server/modem shutdown). 2.9 Point-of-Sales Support Point-of-Sales (POS) terminals usually need to exchange a small amount of data in the shortest amount of time. Low speed modulations such as Bell212A or V.22 are still mainly used in POS applications. Additionally, new non-standard sequences have been developed to better support POS applications. Industry standard and shortened answer tone B103 and V.21 are supported, as well as FastPOS (V.29) and V.22 FastConnect. POS terminal modulations are supported by the $F command. 2.10 Fax Class 1, Fax Class 1.0, and Fax Class 2 Operation Facsimile functions operate in response to fax class 1 commands when +FCLASS=1, to fax class 1.0 commands when +FCLASS=1.0, or to fax class 2 commands when +FCLASS=2. In the fax mode, the on-line behavior of the modem is different from the data (non-fax) mode. After dialing, modem operation is controlled by fax commands. Some AT commands are still valid but may operate differently than in data modem mode. Calling tone is generated in accordance with T.30. 2.11 Tone Detectors The modem is equipped with three tone detectors with separate signal paths from the main received signal path thus enabling tone detection to be independent of the configuration status. 2.12 Call Waiting Tone Detection Call Waiting tones can be detected when in V.92, V.90, V.34, and V.32bis data modes. 32 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 2.13 Technical Specifications Caller ID Both Type I Caller ID (On-Hook Caller ID) and Type II Caller ID (Call Waiting Caller ID) are supported for U.S. and many other countries (see Section 2.14). Both types of Caller ID are enabled/disabled using the +VCID command. Call Waiting Tone detection must be enabled using the +PCW command to detect and decode Call Waiting Caller ID. When enabled, caller ID information (date, time, caller code, and name) can be passed to the DTE in formatted or unformatted form. Inquiry support allows the current caller ID mode and mode capabilities of the modem to be retrieved from the modem. Type II Caller ID (Call Waiting Caller ID) detection operates only during data mode in V.92, V.90, V.34, V.32bis, or V.32. 2.14 Worldwide Country Support Internal modem firmware supports 63 country profiles (see Table 2). These country profiles include the following country-dependent parameters: * Dial tone detection levels and frequency ranges. DTMF dialing parameters: Transmit output level, DTMF signal duration, and DTMF interdigit interval. Pulse dialing parameters: Make/break times, set/clear times, and dial codes are programmable. Ring detection frequency range. Type I and Type II Caller ID detection are supported for many countries. Contact your local Conexant sales office for additional country support. * Blind dialing enabled/disable. Carrier transmit level. The maximum, minimum, and default values can be defined to match specific country and DAA requirements. Calling tone is generated in accordance with V.25. Calling tone may be toggled (enabled/disabled) by inclusion of a "^" character in a dial string. It may also be disabled. Frequency and cadence of tones for busy, ringback, congested, warble, dial tone 1, and dial tone 2. Answer tone detection period. Blacklist parameters. The modem can operate in accordance with requirements of individual countries to prevent misuse of the network by limiting repeated calls to the same number when previous call attempts have failed. Call failure can be detected for reasons such as no dial tone, number busy, no answer, no ringback detected, voice (rather than modem) detected, and key abort (dial attempt aborted by user). Actions resulting from such failures can include specification of minimum inter-call delay, extended delay between calls, and maximum numbers of retries before the number is permanently forbidden ("blacklisted"). The country profiles may be altered or customized by modifying the countrydependent parameters. Additional profiles may also be included. Additional and modified country profiles are supported by internal SRAM. Please contact an FAE at the local Conexant sales office for additional and modified country profile support. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 33 Technical Specifications 2.15 CX93011-2x CSMxx Data Sheet Diagnostics Diagnostics are performed in response to test commands. 2.15.1 Analog Loopback (&T1 Command). Data from the local DTE is sent to the modem, which loops the data back to the local DTE. 2.15.2 Analog Loopback (&T1 Command). Data from the local DTE is sent to the modem, which loops the data back to the local DTE. 2.16 Low Power Modes The modem enters a low power mode when no line connection exists and no host activity occurs for the period of time specified in the S24 register. The modem supports four low power modes: Idle Mode, Sleep Mode, Deep Sleep Mode, and Stop Mode. The low power mode entered depends on the setting of the -SLP command. 2.16.1 Idle Mode In Idle mode, the CPU and SPX clocks stop, and the SSD clock runs at low frequency. The modem can detect and qualify ring signals and process AT commands. The modem returns to normal mode upon receiving an AT command or receiving a qualified ring. 2.16.2 Sleep Mode In Sleep mode, the SPX clock stops, and the CPU and SSD clocks run at low frequency. The modem can detect and qualify ring signals. The modem cannot process AT commands. The modem can be awakened by the host sending a single (any) character (typically followed by an AT command) or by the modem receiving a qualified ring. 2.16.3 Deep Sleep Mode In Deep Sleep mode, the SPX and SSD clocks stop, and the CPU clock runs at low frequency. The modem can detect and qualify ring signals. The modem cannot process AT commands. The modem can be awakened by the host sending a single (any) character (typically followed by an AT command) or by the modem receiving a qualified ring. 2.16.4 Stop Mode In Stop mode, the CPU, SPX and SSD clocks stop. The modem cannot process AT commands and cannot detect and qualify ring signals. The modem can be awakened by the host sending a single (any) character (typically followed by an AT command). 34 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 3 Hardware Interface 3.1 CX93011-2x Modem Hardware Interface Signals 3.1.1 CX93011-2x Modem Interface Signal Summary 3.1.1.1 LSD Interface (Through DIB) The DIB interface signals are: DIBP DIBN 3.1.1.2 Call Progress Speaker Interface The call progress speaker interface signal is: Digital speaker output (DSPKOUT); output 3.1.1.3 Clock Select Interface The clock select interface signal is: Clock Select (CLKSEL); input 3.1.1.4 Serial EEPROM Interface The 2-line serial interface signals to an optional serial EEPROM are: Bidirectional Data input/output (NVMDATA) Clock output (NVMCLK) 3.1.1.5 Serial DTE Interface and Indicator Outputs The supported DTE interface signals are: Serial Transmit Data input (TXD#) Serial Receive Data output line (RXD#) Clear to Send output (CTS#) Received Line Signal Detector output (RLSD#) Ring Indicator output (RI#) Data Terminal Ready control input (DTR#) Request to Send control input (RTS#) DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 35 Hardware Interface 3.1.2 CX93011-2x CSMxx Data Sheet CX93011-2x Modem Pin Assignments and Signal Definitions CX93011-2x Modem hardware interface signals are shown by major interface in Figure 2, are shown by pin number in Figure 3, and are listed by pin number in Table 4. CX93011-2x Modem hardware interface signals are defined in Table 5. Figure 2. CX93011-2x Modem Hardware Interface Signals 18 19 28.224 OR 27.000 MHZ CRYSTAL OR CLOCK OSCILLATOR 2 1 6 8 9 7 5 SERIAL HOST INTERFACE XTLI XTLO TXD# RXD# CTS# RLSD# RI# DTR# RTS# FREQUENCY SELECT CIRCUIT DIBN DIBP DSPKOUT CX93011-2x Modem 20-Pin QFN 4 12 SERAIL EEPROM 20 RESET CIRCUIT 20 k 240 k (1) +3.3V 14 NVMCLK/CLKSEL NVMDATA VDD_CORE VDD VDD GND PADDLE (GND) 10 11 17 15 3 13 DIGITAL ISOLATION BARRIER (DIB) SPEAKER CIRCUIT +1.2V DECOUPLING +3.3V 16 21 RESET# LPO GENERAL NOTE: PADDLE (GND), indicated as Pin 21, is a conductive surface on the bottom of the device and must be connected to system side digital ground. FOOTNOTE: 20 k pull-down resistor required. RESET# XTLO XTLI DSPKOUT GND 19 18 17 16 CX93011-2x Modem 20-Pin QFN Pin Signals 20 Figure 3. (1) RXD# VDD_CORE TXD# LPO VDD VDD NVMCLK/CLKSEL CX93011-2X RTS# NVMDATA 6 7 8 9 10 CTS# DTR# RLSD# RI# DIBN DIBP GENERAL NOTE: PADDLE (GND is a conductive surface on the bottom of the device and is indicated as pin 21. 36 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Hardware Interface Table 4. CX93011-2x Modem 20-Pin QFN Pin Signals Pin Number Signal Name Pin Number Signal Name 1 RXD# 11 DIBP 2 TXD# 12 NVMDATA 3 VDD 13 VDD 4 NVMCLK/CLKSEL 14 LPO 5 RTS# 15 VDD_CORE 6 CTS# 16 GND 7 DTR# 17 DSPKOUT 8 RLSD# 18 XTLI 9 RI# 19 XTLO 10 DIBN 20 RESET# 21 PADDLE (GND)(1) FOOTNOTES: (1) PADDLE (GND) is a conductive surface on the bottom of the device and is indicated as pin 21. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 37 Hardware Interface Table 5. CX93011-2x CSMxx Data Sheet CX93011-2x Modem 20-Pin QFN Pin Signals (1 of 2) Label Pin I/O I/O Type Signal Name/Description System XTLI XTLO 18 19 I O Ix Ox Crystal In and Crystal Out. If an external 27 or 28.224 MHz crystal circuit is used instead of an external clock circuit, connect XTLI and XTLO to the external crystal circuit. When an external clock circuit is used, connect the clock signal to XTLI and leave XTLO open. (See CLKSEL pin description.) NVMCLK/CLKSEL 4 I Ipu/O2 Clock Frequency Select (CLKSEL). Clock frequency is selected by CLKSEL during reset processing. Leave open for 28.224 MHz operation; connect pin to digital ground (GND) through 10 k for 27.000 MHz operation. This signal is multiplexed with NVMCLK. RESET# 20 I Ipu/O2 Reset. The active low RESET# input resets the modem logic and clears the internal SRAM. RESET# low holds the modem in the reset state; RESET# going high releases the modem from the reset state. During application of VDD, RESET# must be held low before VDD power is applied and for at least 15 ms after VDD reaches operating range. The modem device set is ready to use 25 ms after the low-to-high transition of RESET#. Since some application may use external host GPIO to control RESET# signal, it will be necessary to have an external 20 k pull-down resistor on RESET# to ensure signal is low while applying VDD to the system. VDD_CORE 15 O PWR +1.2V Internal Core Voltage Filter. Internal +1.2 V core voltage for decoupling. Do not connect this pin to an external +1.2 V power supply. VDD 3,13 O PWR Digital and I/O Circuits Supply Voltage. Connect this pin to an external +3.3 V power supply. GND 16 I GND Digital Ground. Connect to digital ground (GND). PADDLE (GND) 21 G GND Paddle Ground. Connect to digital ground (GND). LPO 14 I Low Power Oscillator. Connect to +3.3V through 240 k. Speaker Interface DSPKOUT 17 O Ipd/O2 Modem Speaker Digital Output. The DSPKOUT digital output reflects the received analog input signal digitized to TTL high or low level by an internal comparator. DIB Interface DIBN 10 O Opdc DIB Negative. Provides clock and power to the LSD, and transfers data, control and status information between the SSD and LSD. Connect to DIB transformer primary winding terminal. DIBP 11 O Opdc DIB Positive. Provides clock and power to the LSD and transfers data, control and status information between the SSD and LSD. Connect to DIB transformer primary winding terminal. NVRAM Interface NVMCLK/CLKSEL 4 I/O Ipu/O2 NVRAM Clock (NVMCLK). During normal operation, NVMCLK/CLKSEL output high enables the EEPROM. Connect to EEPROM SCL pin. This signal is multiplexed with CLKSEL. NVMDATA 12 I/O Ipu/O2 NVRAM Data. The NVMDATA pin supplies a serial data interface to the EEPROM. Connect to EEPROM SDA pin and to +3.3V through 10 K. 38 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Table 5. Hardware Interface CX93011-2x Modem 20-Pin QFN Pin Signals (2 of 2) Label Pin I/O I/O Type Signal Name/Description V.24 (EIA/TIA-232-E) DTE Serial Interface TXD# 2 I Ipu/O2 Transmitted Data (EIA BA/ITU-T CT103). The DTE uses the TXD# line to send data to the modem for transmission over the telephone line or to transmit commands to the modem. RXD# 1 O Ipu/O2 Received Data (EIA BB/ITU-T CT104). The modem uses the RXD# line to send data received from the telephone line to the DTE and to send modem responses to the DTE. During command mode, RXD# data represents the modem responses to the DTE. CTS# 6 O Ipu/O2 Clear To Send (EIA CB/ITU-T CT106). CTS# output ON (low) indicates that the modem is ready to accept data from the DTE. In error correction or normal mode, CTS# is always ON (low) unless RTS/CTS flow control is selected by the &Kn command. RTLSD# 8 O Ipu/O2 Received Line Signal Detector (EIA CF/ITU-T CT109). During normal operation, when AT&C0 command is not in effect, RLSD# output is ON when a carrier is detected on the telephone line or OFF when carrier is not detected. RI# 9 O Ipu/O2 Ring Indicator (EIA CE/ITU-T CT125). RI# output ON (low) indicates the presence of an ON segment of a ring signal on the telephone line. DTR# 7 I Ipu/O2 Data Terminal Ready (EIA CD/ITU-T CT108). The DTR# input is turned ON (low) by the DTE when the DTE is ready to transmit or receive data. DTR# ON prepares the modem to be connected to the telephone line, and maintains the connection established by the DTE (manual answering) or internally (automatic answering). DTR# OFF places the modem in the disconnect state under control of the &Dn and &Qn commands. RTS# 5 I Ipu/O2 Request To Send (EIA CA/ITU-T CT105). RTS# input ON (low) indicates that the DTE is ready to send data to the modem. In the command state, the modem ignores RTS#. The modem ignores RTS# unless RTS/CTS flow control is selected by the &Kn command. GENERAL NOTES: I/O Types: See Table 6. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 39 Hardware Interface 3.1.3 CX93011-2x CSMxx Data Sheet CX93011-2x Modem Electrical Characteristics CX93011-2x I/O types are defined in Table 6. CX93011-2x DC electrical characteristics are listed in Table 7. Table 6. CX93011-2x Modem I/O Type Definitions I/O Type Description Idd/Odd Digital input/output, DIB data transceiver Ix/Ox I/O, wire Ipd/O2 Digital input, 120 k pull-down/Digital output, 2 mA Ipu/O2 Digital input, 120 k pull-up / Digital output, 2 mA Ippu/O2 Digital input, Programmable 120 k pull-up / Digital output, 2 mA Odpc Digital output with adjustable drive, DIB clock and power Rx Oscillator Pad, place 120 k resistor from pad to VDD PWR Power GND Ground GENERAL NOTES: 1. See DC characteristics in Table 7. 2. I/O Type corresponds to the device Pad Type. The I/O column in signal interface tables refers to signal I/O direction used in the application. Table 7. CX93011-2x Modem DC Electrical Characteristics Parameter Symbol Minimum Maximum Units Test Conditions Input Voltage Low VIL 0 0.3 *VDD V Input Voltage High VIH 0.7 * VDD VDD V Input Current (no Pull-Down or Pull-Up) IIL -1 +1 A OEN = 1 Input Current (Pull-Down) IPD +6 +30 A VIN = VDD Input Current (Pull-Up) IPU -300 -60 A VIN = GND Output Voltage Low VOL 0 0.4 V IOL = +2 mA Output Voltage High VOH VDD-0.4 VDD V IOL = -2 mA Output Impedance Z 25 95 Pull-Up Resistance Rpu 120 500 k VIN = GND Pull-Down Resistance Rpd 120 500 k VIN = VDD GENERAL NOTES: Test Conditions unless otherwise stated: VDD = +3.3V 5%; TA = -10C to 70C; external load = 50 pF. 40 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Hardware Interface 3.2 CX20548 LSD Hardware Pins and Signals 3.2.1 General 3.2.1.1 Host Side Device (HSD) Interface (Through DIB) The DIB interface signals are: DIB Positive (DIBP, pin 14); input/output DIB Negative (DIBN, pin 16); input/output 3.2.1.2 Power and Ground The power and ground signals are: Unregulated Power Output (PWR, pin 15) Regulated Digital Power Output (DVDD, pin 1) Regulated Analog Power Output (AVDD, pin 2) Analog Ground (PADDLE [AGND]); Analog ground 3.2.1.3 Telephone Line Interface The telephone line interface signals are: RING AC Coupled (RAC, pin 4); input TIP AC Coupled (TAC, pin 5); input Electronic Inductor Capacitor (EIC, pin 11) Electronic Inductor Output (EIO, pin 10) Electronic Inductor Feedback (EIF, pin 9) Receive Analog Input (RXI, pin 6); input Transmit Output (TXO, pin 8); output Transmit Feedback (TXF, pin 7); input 3.2.1.4 Voltage References There is on reference voltage pin: Output Middle (Center) Reference Voltage (VC, pin 3); output for decoupling 3.2.1.5 General Purpose Input/Output There is one unassigned general purpose input/output pin: General Purpose Input/Output (GPIO, pin 13); input/output DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 41 Hardware Interface 3.2.2 CX93011-2x CSMxx Data Sheet Pin Assignments and Signal Definitions CX20548 LSD hardware interface signals are shown by major interface in Figure 4, are shown by pin number in Figure 5, and are listed by pin number in Table 8. NOTE: Pin 17 is shown in Figure 4 to ensure that the PADDLE is considered when laying out the printed circuit board. The PADDLE is the analog ground pin of the CX20548 device and must be connected to LSD analog ground (AGND_LSD) when the CX20548 is populated in a PCB. CX20548 LSD hardware interface signals are defined in Table 9. CX20548 LSD GPIO DC characteristics are specified in Table 10. CX20548 LSD AVDD DC characteristics are specified in Table 11. 42 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Figure 4. Hardware Interface CX20548 LSD Hardware Interface Signals Digital Isolation Barrier C850 RAC 16 DIBN TAC R802 4 R804 5 DIBN Electronic Inductor, Off-Hook, Pulse Dial, and TIP and RING VI Control C862 14 DIBP EIC EIO EIF DIBP T802 C852 R854 2 TEST CX20548 SmartDAA4 Line Side Device 16-Pin QFN AGND_LSD 1 DVDD C830 AGND_LSD 15 2 C870 11 10 9 RXI Safety and EMI Protection Telephone TIP Line RING Connector Receive Coupling 6 AGND_LSD TXO TXF Impedance Matching and Transmitter 8 7 PWR+ AVDD VC 3 C828 C844 AGND_LSD AGND_LSD 17 GPIO 13 NC PADDLE (AGND) AGND_LSD GENERAL NOTES: 1. Consult applicable reference design for exact component placement and values, and for layout guidelines. 2. The PADDLE (indicated as Pin 17) is the analog ground pin of the CX20548 device and must be connected to LSD analog ground (AGND_LSD) when the CX20548 is populated in a printed circuit board (PCB). DIBN PWR DIBP GPIO 16 15 14 13 CX20548 LSD 16-Pin QFN Pin Signals DVDD 1 12 TEST AVDD 2 11 EIC VC 3 10 EIO RAC 4 9 EIF 5 6 7 8 RXI TXF TXO CX20548 TAC Figure 5. GENERAL NOTE: The PADDLE, a connective surface located on the bottom of the package and referred to as pin 17, is connected internally to analog ground (AGND). DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 43 Hardware Interface Table 8. CX93011-2x CSMxx Data Sheet CX20548 LSD 16-Pin QFN Pin Signals Pin Signal Label Pin Signal Label 1 DVDD 9 EIF 2 AVDD 10 EIO 3 VC 11 EIC 4 RAC 12 TEST 5 TAC 13 GPIO 6 RXI 14 D/BP 7 TXF 15 PWR 8 TXO 16 B/BN 17 PADDLE (AGND) Table 9. CX20548 LSD Hardware Signal Definitions (1 of 2) Label Pin I/O I/O Type Signal Name/Description System Interface Signals PWR 15 PWR PWR Unregulated Power Output. Unregulated power output from the internal rectifier, connect to AGND_LSD through C870. VC 3 REF REF Output Middle Reference Voltage. Connect to AGND_LSD through C844, which must be placed close to pin 3. Use a short path and a wide trace to the AGND_LSD pin. AVDD 2 PWR PWR Analog Power Output. Provides external connection point for decoupling. (AVDD is routed internally to LSD analog circuits.) Connect to AGND_LSD through C828. C828 must be placed close to pin 2. DVDD 1 PWR PWR Digital Power Output. Provides external connection point for decoupling. Connect to AGND_LSD through C830. Place C830 near pin 1. PADDLE (AGND) 17 AGND_LSD AGND_LSD Paddle Analog Ground. The conductive surface located on the bottom of the package and referred to as pin 17 is connected internally to device analog ground. Connect to AGND_LSD. DIB Interface Signals DIBP 14 I/O I/O DIB Positive. Positive terminal of DIB, connect to secondary of DIB transformer. DIPN 16 I/O I/O DIB Negative. Negative terminal of DIB, connect to secondary of DIB transformer. 44 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Table 9. Hardware Interface CX20548 LSD Hardware Signal Definitions (2 of 2) Label Pin I/O I/O Type Signal Name/Description TIP and RING Interface Signals RAC 4 I Ia RING AC Coupled and TIP AC Coupled. Un-rectified voltage from telephone line used to detect ring. Connect RAC to the diode bridge AC node (RING) through R802 (connects to pin 4). Connect TAC to the diode bridge AC node (TIP) through R804 (connects to pin 5). TAC 5 I Ia EIC 11 O Oa Electronic Inductor Capacitor. Electronic inductor filtering capacitor. Connect to AGND_LSD through C858. EIO 10 O Oa Electronic Inductor Output. Calculated voltage is applied to this output to control off-hook and DC VI mask operation. Connect to base of Q804. EIF 9 I Ia Electronic Inductor Feedback. Connect to emitter of Q804 through R826. RXI 6 I Ia Receive Analog Input. Receiver operational amplifier inverting input. AC coupled to the Bridge_CC node through R810 (connects to pin 6) and C810 in series. R810 and C810 must be placed very close to pin 6. The length of the PCB trace connecting R810 to the RXI pin must be kept at an absolute minimum. TXO 8 O Oa Transmit Output. Outputs transmit signal and impedance matching signal; connect to base of transistor Q802. TXF 7 I Ia Transmit Feedback. Connect to emitter of transistor Q802. Not Used GPIO 13 I/O It/Ot12 General Purpose I/O. Leave open if not used. GENERAL NOTES: 1. I/O types*: Ia Analog input It Digital input* Oa Analog output Ot12 Digital output* AGND_LSD Isolated LSD Analog Ground (isolated from the host system ground) *See CX20548 LSD GPIO DC Electrical Characteristics (Table 10). 2. Refer to applicable reference design for exact component placement and values. DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 45 Hardware Interface Table 10. CX93011-2x CSMxx Data Sheet CX20548 LSD GPIO DC Electrical Characteristics Parameter Symbol Minimum Typical Maximum Units Test Conditions Input Voltage VIN -0.30 -- 3.465 V DVDD = +3.465 V Input Voltage Low VIL -- -- 1.0 V Input Voltage High VIH 1.6 -- -- V Output Voltage Low VOL 0 -- 0.33 V Output Voltage High VOH 2.97 -- -- V Input Leakage Current -- -10 -- 10 A Output Leakage Current (High Impedance) -- -10 -- 10 A GPIO Output Sink Current at 0.33 V maximum -- 2.4 -- -- mA GPIO Output Source Current at 2.97 V minimum -- 2.4 -- -- mA 100 ns GPIO Rise Time/Fall Time 20 GENERAL NOTES: Test Conditions, unless otherwise stated: DVDD = +3.3 V +5%; TA = 0C to 70C; external load = 50 pF. Table 11. CX20548 LSD AVDD and DVDD DC Electrical Characteristics PWR Input AVDD Output DVDD Output +3 V < PWR < +4.0 V +3 V + 5% +3 V + 5% GENERAL NOTES: PWR must be at least 100 mV higher than AVDD. See PWR, AVDD, and DVDD descriptions in Table 9. 46 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 3.3 Hardware Interface Operating Conditions, Absolute Maximum Ratings, and Power Requirements The CX93011-2x operating conditions are specified in Table 12. The CX93011-2x absolute maximum ratings are listed in Table 13. The CX93011-2x current and power requirements are listed in Table 14. Table 12. CX93011-2x Modem Operating Conditions Parameter Symbol Limits Units VDD +3.3 + 5% VDC TA 0 to +70 C Supply Voltage Operating Ambient Temperature GENERAL NOTES: Voltages referenced to ground (VSS). Table 13. Absolute Maximum Ratings Parameter Symbol Limits Units VDD Supply Voltage VDD -0.5 to +4.0 VDC Storage Temperature Range TSTG -55 to +125 C Relative Humidity HREL Up to 90% non-condensing, or a wet bulb temperature up to 35 C, whichever is less. Input Voltage VIN -0.3 to (VDD + 0.3) VDC Voltage Applied to Outputs in High Impedance (Off) State VHZ -0.5 to +5.5 VDC DC Input Clamp Current IIK 20 mA DC Output Clamp Current IOK 20 mA Static Discharge Voltage (25C) VESD 2500 VDC Latch-up Current (25C) ITRIG 400 mA DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 47 Hardware Interface 3.3.1 CX93011-2x CSMxx Data Sheet Handling CMOS Devices The device contains circuitry to protect the inputs against damage due to high static voltages. However, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltage. An unterminated input can acquire unpredictable voltages through coupling with stray capacitance and internal cross talk. Both power dissipation and device noise immunity degrades. Therefore, all inputs should be connected to an appropriate supply voltage. Input signals should never exceed the voltage range from -0.3V to (VDD + 0.3) V. This prevents forward biasing the input protection diodes and possibly entering a latch up mode due to high current transients. Table 14. CX93011-2x Current and Power Requirements Typical Current (mA) Maximum Current (mA) Normal Mode: On-hook, Idle, waiting for ring 75 85 248 295 Normal Mode: Off-hook, normal data connection 87 97 287 336 Idle Mode (-SLP=0) 16 23 53 80 Sleep Mode (-SLP=1) 16 23 53 80 Deep Sleep Mode (-SLP=2) 7 13 23 45 Stop Mode (-SLP=3) 5 11 17 38 Mode Typical Power (mW) Maximum Power (mW) GENERAL NOTES: 1. Test conditions: VDD = +3.3V for typical values; VDD = +3.465V for maximum values. 2. Input Ripple 0.1 Vpeak-peak. 48 Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet 3.4 Hardware Interface Crystal and Clock Specifications Crystal specifications are listed in Table 15. Clock specifications are listed in Table 16. Table 15. Crystal Specifications Characteristics Value Frequency 28.224 or 27.000 MHz nominal Calibration Tolerance 50 ppm at 25C (CL = 16.5 and 19.5 pF) Frequency Stability vs. Temperature 35 ppm (-10C to 70C) Frequency Stability vs. Aging 20 ppm/5 years Oscillation Mode Fundamental Calibration Mode Parallel resonant Load Capacitance, CL 18 pF nominal Shunt Capacitance, CO 7 pF maximum Series Resistance, R1 35-60 maximum @ 20 nW drive level Drive Level 100 W correlation; 500 W maximum Operating Temperature -10C to 70C Storage Temperature -40C to 85C Table 16. Clock Specifications Characteristics Value Type Square wave Frequency 28.224 or 27.000 MHz nominal Level 3.3 Vp-p 0.3 V zero offset Duty Cycle 50 10% Stability 50 DSH-201689G 7/17/12 Conexant Conexant Proprietary and Confidential 49 Hardware Interface 50 CX93011-2x CSMxx Data Sheet Conexant Conexant Proprietary and Confidential DSH-201689G 7/17/12 4 Package Dimensions The CX93011-2x comes in a 20-pin package in either punch or sawn style. Both are electrically equivalent and share the same footprint. Table 17 provides a dimension table that is common to both QFN styles. The punch-style package is shown in Figure 6, and the sawn-style package is shown in Figure 7. Table 17. Package Dimensions for 20-Pin Punch and Sawn Styles Dim. mm Min. e Nom. Note Max. 0.8 BSC L 0.5 0.75 b 0.28 0.4 D2 3.95 4.25 E2 3.95 4.25 A 0.8 0.90 A1 0.00 0.05 A3 0.20 REF. D 6.00 BSC D1 5.75 BSC E 6.00 BSC E1 5.75 BSC (1) (1) GENERAL NOTES: 1. All dimensions in mm. 2. Shape of Pin #1 indicator on the bottom of package can be different (i.e., Chamfer, Half Circle). FOOTNOTES: (1) This dimension is applied only for Punched QFN. DSH-201689G 7/17/12 (c) 2012 Conexant Systems, Inc. 51 Package Dimensions Figure 6. 52 CX93011-2x CSMxx Data Sheet Package Dimensions for 20-Pin QFN, Punch Style (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Figure 7. Package Dimensions for 20-Pin QFN, Sawn Style DSH-201689G 7/17/12 Package Dimensions (c) 2012 Conexant Systems, Inc. 53 Package Dimensions CX93011-2x CSMxx Data Sheet The CX20548 comes in a 16-pin QFN package, in either punch or sawn style. Both are electrically equivalent and share the same footprint. Table 18 provides a dimension table that is common to both QFN styles. The punch-style package is shown in Figure 8, and the sawn-style package is shown in Figure 9. Table 18. Dim. Package Dimensions for 16-Pin Punch and Sawn Styles Minimum e Nominal Maximum Note 0.65 BSC L 0.5 0.75 b 0.21 0.35 D2 1.95 2.10 2.25 E2 1.95 2.10 2.25 A 0.8 1.00 A1 0.00 0.05 A3 0.20 REF. D 4.00 BSC D1 3.75 BSC E 4.00 BSC E1 3.75 BSC (1) (2) (2) GENERAL NOTES: 1. All dimensions in mm. 2. Shape of Pin #1 indicator on the bottom of package can be different (i.e., Chamfer or Half Circle) FOOTNOTES: (1) Dimension b applies to plated terminal and is measured between 0.20 and 0.30 mm from terminal tip. (2) This dimension is applied only for Punched QFN.. 54 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 CX93011-2x CSMxx Data Sheet Figure 8. Package Dimensions Package Dimensions for 16-Pin QFN, Punch Style A D A1 D1 A3 D2 16 16 Pin 1 Identifier Pin 1 Identifier 1 1 2 3 E1 2 E 3 E2 L e b SEATING PLANE TOP VIEW SIDE VIEW BOTTOM VIEW b A1 NOTE 1 e SECTION "C-C" SCALE: NONE TERMINAL TIP DSH-201689G 7/17/12 (c) 2012 Conexant Systems, Inc. 55 Package Dimensions Figure 9. CX93011-2x CSMxx Data Sheet Package Dimensions for 16-Pin QFN, Sawn Style 16 b 56 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 5 Recommended QFN Surface Mount Land Patterns The recommended surface mount land patterns based on the IPC-SM-782 standard for board layout are shown in Figure 10 for the 20-pin QFN and Figure 11 for the 16pin QFN. Figure 10. Recommended Surface Mount Land Pattern for 20-Pin QFN DSH-201689G 7/17/12 (c) 2012 Conexant Systems, Inc. 57 Recommended QFN Surface Mount Land Patterns CX93011-2x CSMxx Data Sheet Figure 11. Recommended Surface Mount Land Pattern for 16-Pin QFN 58 (c) 2012 Conexant Systems, Inc. DSH-201689G 7/17/12 www.conexant.com General Information: U.S. and Canada: (888) 855-4562 International: (949) 483-4600 Headquarters - Newport Beach 4000 MacArthur Blvd. Newport Beach, CA 92660