PD15-21C/TR8 - Everlight International Corp.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

Technical Data Sheet

1206 Package Silicon PIN Photodiode

PD15-21C/TR8

Features

․Fast response time

․High photo sensitivity

․Small junction capacitance

․Package in 8mm tape in “13” diameter reel

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

․PD15-21C/TR8 is a high speed and high sensitive

PIN photodiode in miniature flat top view lens

SMD package and it is molded in a clear epoxy.

The device is spectrally matched to infrared emitting

diode.

Applications

․High speed photo detector

․Copier

․Game machine

Device Selection Guide Chip

Part No. Material Resin Color

PD15-21C/TR8 Silicon Water Clear

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 2 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Package Dimensions

1.5

1.2 1.2

Notes: 1.All dimensions are in millimeters

2.Tolerances unless dimensions ±0.1mm

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 3 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit

Reverse Voltage VR 32 mA

Operating Temperature Topr -25 ~ +85 ℃

Storage Temperature Tstg -40 ~ +85 ℃

Soldering Temperature *1 Tsol 260 ℃

Power Dissipation at(or below)

25℃Free Air Temperature Pc 150 mW

Notes: *1:Soldering time≦5 seconds.

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Condition Min Typ Max Unit

Rang Of Spectral Bandwidth λ0.5 --- 400 --- 1100 nm

Wavelength Of Peak Sensitivity λP --- --- 940 --- nm

Open-Circuit Voltage VOC Ee=1mW /cm2

λP=875nm --- 0.42 --- V

Short-Circuit Current ISC Ee=1mW /cm2

λP=875nm --- 0.8 ---

μA

Reverse Light Current IL Ee=1mW /cm2

λP=875nm

VR=5V 0.2 0.8 ---

μA

Dark Current ID Ee=0mW /cm2

VR=10V --- --- 10 nA

Reverse Breakdown Voltage VBR Ee=0mW /cm2

IR=100μA 32 170 --- V

Total Capacitance Ct Ee=0mW /cm2

f=1MHz

VR=5V --- 5 --- pF

Rise Time tr --- 6 ---

Fall Time tf

VR=5V

RL=1000Ω --- 6 ---

ns

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 4 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

0-25

50

100

150

25

050

200

75 85 100

160

20 40 10080

100

10

1000

VR=10V

100

0.2

0

0.4

700500300

Ta=25

0.8

0.6

1.0

C

13001100900

PD15-21C/TR8

Typical Electro-Optical Characteristics Curves

Fig.1 Power Dissipation vs. Fig.2 Spectral Sensitivity

Ambient Temperature

Fig.3 Dark Current vs. Fig.4 Reverse Light Current vs.

Ambient Temperature Ee

0.5

01.0

0.5

1.5

1.0

1.5 3.0

2

2.0

VR=5V

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 5 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

10

-3

-2

-1

0

1

1012

10 103104105

VR=10V

Ta=25°C

0.1

2

4

8

6

100110

t

10 f=1MHZ

2

VR=5V

PD15-21C/TR8

Typical Electro-Optical Characteristics Curves

Fig.5 Terminal Capacitance vs. Fig.6 Response Time vs.

Reverse Voltage Load Resistance

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 6 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.

If unused LEDs remain, it should be stored in moisture proof packages.

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Lead solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 7 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3

seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more

intervals, and do soldering of each terminal. Be careful because the damage of the product is often

started at the time of the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed

beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 8 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Reliability Test Item and Condition

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

NO. Item Test Conditions Test Hours/

Cycles

Sample

Sizes

Failure

Judgment

Criteria

Ac/Re

1 REFLOW Soldering TEMP.：260℃±5℃

10secs

6Mins 22pcs 0/1

2 Temperature Cycle H : +100℃ 30mins

5mins

L : -40℃ 30mins

50Cycles 22pcs 0/1

3 Thermal Shock H :+100℃ 5mins

10secs

L :-10℃ 5mins

50Cycles 22pcs 0/1

4 High Temperature

Storage

TEMP.：+100℃ 1000hrs 22pcs 0/1

5 Low Temperature

Storage

TEMP.：-40℃ 1000hrs 22pcs 0/1

6 DC Operating Life VR=5V 1000hrs 22pcs 0/1

7 High Temperature/

High Humidity

85℃ / 85% R.H 1000hrs 22pcs

IL≦L×0.8

L：Lower

Specification

Limit

0/1

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 9 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Package Dimensions

Taping Dimensions

Unit:mm

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 10 of 10

Device No：SZDTD Prepared date：26-Oct-2009 Prepared by：Cheng Dejiang

PD15-21C/TR8

Packing Quantity Specification

1.2000Pcs/1Volume，1Volume/1Bag

2.10Boxes/1Carton

Label Form Specification

CPN: Customer’s Production Number

P/N : Production Number

QTY: Packing Quantity

CAT: Ranks

HUE: Peak Wavelength

REF: Reference

LOT No: Lot Number

MADE IN TAIWAN: Production Place

Notes

1. Above specification may be changed without notice. EVERLIGHT will reserve authority on

material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions

for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for

any damage resulting from use of the product which does not comply with the absolute

maximu m ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without

EVERLIGHT’s consent.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306

Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com

RoHS

Pb

CPN :

PN : XXXXXXXXXXXXX

XXXXXXXXXXXXX

QTY : XXX

LOT NO : XXXXXXXXXX

Reference : XXXXXXXX

CAT : XXX

HUE : XXX

REF : XXX

EVERLIGHT

MADE IN TAIWAN