Order this document by MRF154/D SEMICONDUCTOR TECHNICAL DATA The RF MOSFET Line N-Channel Enhancement-Mode MOSFET Designed primarily for linear large-signal output stages in the 2.0 - 100 MHz frequency range. * Specified 50 Volts, 30 MHz Characteristics Output Power = 600 Watts Power Gain = 17 dB (Typ) Efficiency = 45% (Typ) 600 W, 50 V, 80 MHz N-CHANNEL BROADBAND RF POWER MOSFET D G CASE 368-03, STYLE 2 (HOG PAC) S MAXIMUM RATINGS Rating Symbol Value Unit Drain-Source Voltage VDSS 125 Vdc Drain-Gate Voltage VDGO 125 Vdc VGS 40 Vdc Drain Current -- Continuous ID 60 Adc Total Device Dissipation @ TC = 25C Derate above 25C PD 1350 7.7 Watts W/C Storage Temperature Range Tstg - 65 to +150 C TJ 200 C Symbol Max Unit RJC 0.13 C/W Gate-Source Voltage Operating Junction Temperature THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction to Case Handling and Packaging -- MOS devices are susceptible to damage from electrostatic charge. Reasonable precautions in handling and packaging MOS devices should be observed. REV 2 RF DEVICE DATA MOTOROLA Motorola, Inc. 1997 MRF154 1 ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit V(BR)DSS 125 -- -- Vdc Zero Gate Voltage Drain Current (VDS = 50 V, VGS = 0) IDSS -- -- 20 mAdc Gate-Body Leakage Current (VGS = 20 V, VDS = 0) IGSS -- -- 5.0 Adc Gate Threshold Voltage (VDS = 10 V, ID = 100 mA) VGS(th) 1.0 3.0 5.0 Vdc Drain-Source On-Voltage (VGS = 10 V, ID = 40 A) VDS(on) 1.0 3.0 5.0 Vdc Forward Transconductance (VDS = 10 V, ID = 20 A) gfs 16 20 -- mhos Input Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Ciss -- 1600 -- pF Output Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Coss -- 950 -- pF Reverse Transfer Capacitance (VDS = 50 V, VGS = 0, f = 1.0 MHz) Crss -- 175 -- pF Common Source Amplifier Power Gain (VDD = 50 V, Pout = 600 W, IDQ = 800 mA, f = 30 MHz) Gps -- 17 -- dB Drain Efficiency (VDD = 50 V, Pout = 600 W, IDQ = 800 mA, f = 30 MHz) -- 45 -- % IMD(d3) -- - 25 -- dB C20 C21 50 V - OFF CHARACTERISTICS Drain-Source Breakdown Voltage (VGS = 0, ID = 100 mA) ON CHARACTERISTICS DYNAMIC CHARACTERISTICS FUNCTIONAL TESTS Intermodulation Distortion (VDD = 50 V, Pout = 600 W (PEP), f1 = 30 MHz, f2 = 30.001 MHz, IDQ = 800 mA) 0-6 V + - + R1 C5 L2 C6 L3 DUT R2 C14 C4 C15 C16 C17 C18 C19 L1 RF INPUT C10 C3 C1 C2 C11 C12 C7 C13 C9 T1 C1, C3, C8 -- Arco 469 C2 -- 330 pF C4 -- 680 pF C5, C19, C20 -- 0.47 F, RMC Type 2225C C6, C7, C14, C15, C16 -- 0.1 F C9, C10, C11 -- 470 pF C12 -- 1000 pF C13 -- Two Unencapsulated 1000 pF Mica, in Series C17, C18 -- 0.039 F C21 -- 10 F/100 V Electrolytic L1 -- 2 Turns #16 AWG, 1/2 ID, 3/8 Long L2, L3 -- Ferrite Beads, Fair-Rite Products Corp. #2673000801 RF OUTPUT C8 R1, R2 -- 10 Ohms/2.0 W Carbon T1 -- RF Transformer, 1:25 Impedance Ratio. See Motorola T1 -- Application Note AN749, Figure 4 for details. T1 -- Ferrite Material: 2 Each, Fair-Rite Products T1 -- Corp. #2667540001 All capacitors ATC type 100/200 chips or equivalent unless otherwise noted. Figure 1. 30 MHz Test Circuit MRF154 2 MOTOROLA RF DEVICE DATA 800 VDD = 50 V Pout , OUTPUT POWER (WATTS) 600 15 10 VDD = 50 V IDQ = 800 mA Pout = 600 W 5 400 40 V 200 0 0 10 (IDQ = 800 mA) 800 600 400 VDD = 50 V 200 0 2 5 10 20 50 f, FREQUENCY (MHz) 100 0 200 40 V 0 Figure 2. Power Gain versus Frequency 50 Pin, INPUT POWER (WATTS) 100 Figure 3. Output Power versus Input Power 100 10,000 VGS = 0 V f = 1 MHz 5000 TC = 25C C, CAPACITANCE (pF) I D, DRAIN CURRENT (AMPS) 20 100 MHz POWER GAIN (dB) 20 30 MHz 25 10 Ciss 2000 Coss 1000 500 Crss 200 1 2 20 VDS, DRAIN-SOURCE VOLTAGE (VOLTS) 100 200 1 Figure 4. DC Safe Operating Area 50 100 600 f t , UNITY GAIN FREQUENCY (MHz) IDS , DRAIN CURRENT (AMPS) 5 10 20 VDS, DRAIN VOLTAGE (VOLTS) Figure 5. Capacitance versus Drain Voltage 40 TYPICAL DEVICE SHOWN VDS = 10 V VGS(th) = 3.5 V gfs = 24 mhos 30 20 10 0 2 0 2 4 6 VGS, GATE-SOURCE VOLTAGE (VOLTS) Figure 6. Gate Voltage versus Drain Current MOTOROLA RF DEVICE DATA 8 500 VDS = 30 V 400 15 V 300 200 100 0 0 20 40 ID, DRAIN CURRENT (AMPS) 60 Figure 7. Common Source Unity Gain Frequency versus Drain Current MRF154 3 f = 100 MHz 60 30 15 Zin VDD = 50 V IDQ = 800 mA Pout = 600 W 7.5 4.0 2.0 Zo = 10 Figure 8. Series Equivalent Impedance BIAS - R13 D2 30 - 40 V + L1 C10 L2 R9 D.U.T. R1 + C5 C2 R5 C4 C8 R6 R4 INPUT R11 IC1 R12 R7 C1 + 40 V - XTR XTR OUTPUT C6 C7 T1 R3 C9 T2 D1 D3 R10 D.U.T. R2 C3 R14 C11 R8 TEMP. TRACKING C1 -- 1000 pF Ceramic C2, C3, C4, C8, C9, C10, C11 -- 0.1 F Ceramic C5 -- 10 F/100 V Electrolytic C6, C7 -- 0.1 F Ceramic, (ATC 200/823 or Equivalent) D1 -- 28 V Zener, 1N5362 or Equivalent D3 -- 1N4148 IC1 -- MC1723 L1, L2 -- Fair-Rite Products Corp. Ferrite Beads #2673000801 R1, R2, R3 -- 10 k Trimpot R4 -- 1.0 k/1.0 W R5 -- 10 Ohms R6 -- 2.0 k R7 -- 10 k R8 -- Thermistor, 10 k (25C), 2.5 k (75C) R9, R10 -- 100 Ohms R11, R12 -- 1.0 k R13, R14 -- 50 - 100 Ohms, 4.0 x 2.0 W Carbon in Parallel T1 -- 9:1 Transformer, Trifilar and Balun Wound on Separate T1 -- Fair-Rite Products Corp. Balun Cores #286100012, 5 Turns Each. T2 -- 1:9 Transformer, Balun 50 Ohm CO-AX Cable RG-188, T2 -- Low Impedance Lines W.L. Gore 16 Ohms CO-AX Type CXN 1837. T2 -- Each Winding Threaded Through Two Fair-Rite Products Corp. T2 -- #2661540001 Ferrite Sleeves (6 Each). XTR -- MRF154 Figure 9. 20 - 80 MHz 1.0 kW Broadband Amplifier MRF154 4 MOTOROLA RF DEVICE DATA RF POWER MOSFET CONSIDERATIONS MOSFET CAPACITANCES The physical structure of a MOSFET results in capacitors between the terminals. The metal oxide gate structure determines the capacitors from gate-to-drain (Cgd), and gate-to- source (Cgs). The PN junction formed during the fabrication of the RF MOSFET results in a junction capacitance from drain-to-source (Cds). These capacitances are characterized as input (Ciss), output (Coss) and reverse transfer (Crss) capacitances on data sheets. The relationships between the inter-terminal capacitances and those given on data sheets are shown below. The Ciss can be specified in two ways: 1. Drain shorted to source and positive voltage at the gate. 2. Positive voltage of the drain in respect to source and zero volts at the gate. In the latter case the numbers are lower. However, neither method represents the actual operating conditions in RF applications. GATE CHARACTERISTICS The gate of the RF MOSFET is a polysilicon material, and is electrically isolated from the source by a layer of oxide. The input resistance is very high -- on the order of 109 ohms -- resulting in a leakage current of a few nanoamperes. Gate control is achieved by applying a positive voltage slightly in excess of the gate-to-source threshold voltage, VGS(th). Gate Voltage Rating -- Never exceed the gate voltage rating. Exceeding the rated VGS can result in permanent damage to the oxide layer in the gate region. Gate Termination -- The gates of these devices are essentially capacitors. Circuits that leave the gate open-circuited or floating should be avoided. These conditions can result in turn-on of the devices due to voltage build-up on the input capacitor due to leakage currents or pickup. Gate Protection -- These devices do not have an internal monolithic zener diode from gate-to-source. If gate protection is required, an external zener diode is recommended. DRAIN Cgd GATE Cds Cgs Ciss = Cgd + Cgs Coss = Cgd + Cds Crss = Cgd SOURCE LINEARITY AND GAIN CHARACTERISTICS In addition to the typical IMD and power gain data presented, Figure 5 may give the designer additional information on the capabilities of this device. The graph represents the small signal unity current gain frequency at a given drain current level. This is equivalent to fT for bipolar transistors. Since this test is performed at a fast sweep speed, heating of the device does not occur. Thus, in normal use, the higher temperatures may degrade these characteristics to some extent. DRAIN CHARACTERISTICS One figure of merit for a FET is its static resistance in the full-on condition. This on-resistance, VDS(on), occurs in the linear region of the output characteristic and is specified under specific test conditions for gate-source voltage and drain current. For MOSFETs, VDS(on) has a positive temperature coefficient and constitutes an important design consideration at high temperatures, because it contributes to the power dissipation within the device. MOTOROLA RF DEVICE DATA MOUNTING OF HIGH POWER RF POWER TRANSISTORS The package of this device is designed for conduction cooling. It is extremely important to minimize the thermal resistance between the device flange and the heat dissipator. Since the device mounting flange is made of soft copper, it may be deformed during various stages of handling or during transportation. It is recommended that the user makes a final inspection on this before the device installation. 0.0005 is considered sufficient for the flange bottom. The same applies to the heat dissipator in the device mounting area. If copper heatsink is not used, a copper head spreader is strongly recommended between the device mounting surfaces and the main heatsink. It should be at least 1/4 thick and extend at least one inch from the flange edges. A thin layer of thermal compound in all interfaces is, of course, essential. The recommended torque on the 4-40 mounting screws should be in the area of 4 - 5 lbs.-inch, and spring type lock washers along with flat washers are recommended. For die temperature calculations, the temperature from a corner mounting screw area to the bottom center of the flange is approximately 5C and 10C under normal operating conditions (dissipation 150 W and 300 W respectively). The main heat dissipator must be sufficiently large and have low R for moderate air velocity, unless liquid cooling is employed. MRF154 5 CIRCUIT CONSIDERATIONS At high power levels (500 W and up), the circuit layout becomes critical due to the low impedance levels and high RF currents associated with the output matching. Some of the components, such as capacitors and inductors must also withstand these currents. The component losses are directly proportional to the operating frequency. The manufacturers specifications on capacitor ratings should be consulted on these aspects prior to design. Push-pull circuits are less critical in general, since the ground referenced RF loops are practically eliminated, and the impedance levels are higher for a given power output. High power broadband transformers are also easier to design than comparable LC matching networks. EQUIVALENT TRANSISTOR PARAMETER TERMINOLOGY Collector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V(BR)CES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCBO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IEBO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VBE(on) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCE(sat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cib . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . hfe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCE(sat) = MRF154 6 Drain Source Gate V(BR)DSS VDGO ID IDSS IGSS VGS(th) VDS(on) Ciss Coss gfs VDS(on) VCE(sat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . r DS(on) = ID IC MOTOROLA RF DEVICE DATA PACKAGE DIMENSIONS -A- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. U 1 K -B- V N 3 2 Q 4 PL 0.25 (0.010) M T A M D N C H E -T- J B M DIM A B C D E H J K N Q U V INCHES MIN MAX 1.490 1.510 0.990 1.010 0.330 0.365 0.490 0.510 0.195 0.205 0.045 0.055 0.004 0.006 0.425 0.500 0.890 0.910 0.120 0.130 1.250 BSC 0.750 BSC MILLIMETERS MIN MAX 37.85 38.35 25.15 25.65 8.38 9.27 12.45 12.95 4.95 5.21 1.14 1.39 0.10 0.15 10.80 12.70 22.87 23.11 3.05 3.30 31.75 BSC 19.05 BSC STYLE 2: PIN 1. DRAIN 2. GATE 3. SOURCE SEATING PLANE CASE 368-03 ISSUE C MOTOROLA RF DEVICE DATA MRF154 7 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. 81-3-5487-8488 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, - US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 INTERNET: http://motorola.com/sps MRF154 8 MRF154/D MOTOROLA RF DEVICE DATA