Panasonic To No. A237-040403N-01 Date 3rd Apr. '04 Type No. ERAC3 Data Sheet EGSM900 Rx SAW Filter Application : Rx Filter for EGSM900 Center Frequency : 942.5MHz Size : 2.0x1.4mm, 5pin-layout Impedance : 50-150ohms unbalance-balance Part No. : EFCH942MTCA7 Issued Check S.Tsuzuki K,Nishimura CIRCUIT COMPONENTS BUSINESS UNIT MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD KADOMA, OSAKA, JAPAN 2003.10.1 EGSM900 Rx SAW Filter ----- Unbalanced input and balanced output ----Part No. : Design No. : T942TGD Parameter Frequency Your request Min. Passband Typ. Our preliminary spec. Max. Min. 925 ... 960 Typ. Unit Max. 925 ... 960 MHz Insertion loss 925 ... 960MHz 1.8 2.5 dB Ripple in passband 925 ... 960MHz 0.5 1.5 dB Amplitude imbalance 925 ... 960MHz -0.5 -0.2 0.1 +0.5 dB Phase imbalance 925 ... 960MHz -5 -1 +1 +5 deg. Att1 DC ... 880MHz 50 63 dB Att2 880 ... 905MHz 25 34 dB Att3 905 ... 915MHz 18 22 dB Att4 980 ... 1500MHz 23 28 dB Att5 1500 ... 3000MHz 40 60 dB Att6 3000 ... 6000MHz 35 60 dB Input 925 ... 960MHz 1.7 2.0 Output 925 ... 960MHz 1.6 2.0 Attenuation VSWR Input impedance (Single Ended) 50 Ohm Output impedance (Differential) 150 // 82 nH Ohm Maximum drive level 13 dBm Operating temperature -10 +80 deg. C Storage temperature -40 +85 deg. C Panasonic 2003.10.1 EGSM900 Rx SAW Filter ----- Unbalanced input and balanced output ----Part No. : Design No. : T942TGD Panasonic 2003.10.1 EGSM900 Rx SAW Filter ----- Unbalanced input and balanced output ----Part No. : Design No. : T942TGD Panasonic 2003.10.1 EGSM900 Rx SAW Filter ----- Unbalanced input and balanced output ----Part No. : Design No. : T942TGD Panasonic UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION BASIC DIMENSIONS Tolerance : +/-0.05 UP TO 2.0 +/- 0.15 TOLERANCE INCL TO INCL TO INCL TO INCL 0.8 +/- 0.15 1.4 +/- 0.15 ABOVE 2-0.735 ISSUE 5-0.38 (2) (1) Input (2) GND (3) Output (4) Output (5) GND (3) DO NOT SCALE DRAWING (4) 0.075 (5) REVISIONS INDICATED BY DATE SCALE DRAW CHECK APPROVAL DRAWING NO. NAME 0.075 REVISIONS FINISH DESIGN 5-0.44 (1) MATERIAL Note : The design manufacturing process, and Specification of this device are subject to change without notice. ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN THIRD ANGLE PROJECT ION UNLESS OTHERWISE SPECIFIED BASIC DIMENSIONS UP TO Measurement Circuit TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE (2) (3) port 2 port 1 (1) 82nH 150 Ohm 50 Ohm port 3 (5) (4) ISSUE MATERIAL REVISIONS FINISH DATE SCAL E DESIGN Input impedance : 50 Ohm ( Single ended ) Output impedance : 150 Ohm ( Differential ) DRAW CHECK APPROVAL DRAWING NO. NAME TYPE NO. SAW Filter Fig. 2 DO NOT SCALE DRAWING REVISIONS INDICATED BY ALL DIMENSIONS ARE IN MILLIMETERS CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION BASIC DIMENSIONS UP TO Recommended land pattern TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE 0.255 0.255 0.810 0.270 5-0.540 5-0.480 ISSUE MATERIAL 0.735 REVISIONS FINISH DATE SCALE DESIGN 0.735 DRAW CHECK APPROVAL DRAWING NO. NAME Note : The design manufacturing process, and Specification of this device are subject to change without notice. DO NOT SCALE DRAWING REVISIONS INDICATED BY ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN