Description
These dual channel optocouplers contain a pair of light
emitting diodes and integrated photo-detectors with
electrical insulation between input and output. Separate
connection for the photodiode bias and output transis-
tor collectors increase the speed up to a hundred times
that of a conventional phototransistor coupler by
reducing the base-collector capacitance.
These dual channel optocouplers are available in an 8
Pin DIP and in an industry standard SO-8 package. The
following is a cross reference table listing the 8 Pin DIP
part number and the electrically equivalent SO-8 part
number.
8 Pin DIP
SO-8
Package
HCPL-4534 HCPL-0534
Functional Diagram
HCPL-4534 and HCPL-0534
Dual Channel, High Speed Optocouplers
Data Sheet
Features
• 15 kV/µs minimum common mode transient
immunity at VCM = 1500 V
• TTL compatible
• Available in 8 pin DIP, SO-8, and 8 pin DIP – gull wing
surface mount (option 300) packages
• High density packaging
• 3 MHz bandwidth
• Open collector outputs
• Guaranteed performance from 0°C to 70°C
• Safety approval
UL Recognized – 3750 V rms for 1 minute (5000 V rms
for 1 minute for Option 020) per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-2
–VIORM = 630 Vpeak for HCPL-4534 0ption 060
– VIORM = 560 Vpeak for HCPL-0534 0ption 060
• Single channel version available (4502/3, 0452/3)
• MIL-PRF-38534 hermetic version available
(55XX/65XX/4N55)
Applications
• Line receivers – high common mode transient
immunity (>1000 V/µs) and low input-output
capacitance (0.6 pF)
• High speed logic ground isolation – TTL/TTL, TTL/
LTTL, TTL/CMOS, TTL/LSTTL
• Replace pulse transformers – save board space and
weight
• Analog signal ground isolation – integrated
photon detector provides improved linearity over
phototransistor type
• Polarity sensing
• Isolated analog amplier – dual channel packaging
enhances thermal tracking
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
A 0.1 µF bypass capacitor between
pins 5 and 8 is recommended.
HCPL-2530 Functional Diagram
7
1
2
3
45
6
8
ANODE 1
CATHODE 1
CATHODE 2
ANODE 2
VCC
VO1
VO2
GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
VO
LOW
HIGH
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
2
The SO-8 does not require “through holes” in a PCB.
This package occupies approximately one-third the
footprint area of the standard dual-in-line package. The
lead prole is designed to be compatible with standard
surface mount processes.
The HCPL-4534/0534 is designed for high speed TTL/TTL
applications. A standard 16 mA TTL sink current through
the input LED will provide enough output current for 1
TTL load and a 5.6 kΩ pull-up resistor. CTR of the HCPL-
4534/0534 is 19% minimum at IF = 16 mA.
Selection Guide
Widebody
Minimum CMR 8-pin DIP (300 Mil) Small-Outline SO-8 (400 Mil) Hermetic
Current Dual Single Dual Single Single Single and
dV/dt V
CM Transfer Channel Channel Channel Channel Channel Dual Channel
(V/µs) (V) Ratio (%) Package Package* Package Package* Package* Packages*
10 HCPL-4502 HCPL-0452 HCNW4502
15,000 1500 19 HCPL-4534 HCPL-4503 HCPL-0534 HCPL-0453 HCNW4503
1,000 10 9 HCPL-55XX
HCPL-65XX
4N55
* Technical data for these products are on separate Avago publications.
The HCPL-4534/0534 is an HCPL-2531/0531 with
increased common mode transient immunity of 15,000
V/µs minimum at VCM = 1500 V guaranteed.
3
Ordering Information
HCPL-4534 and HCPL-0534 are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA
Component Acceptance Notice #5, File CA 88324.
Part
number
Option
Package
Surface
Mount
Gull
Wing
Tape
& Reel
UL 5000
Vrms/ 1
Minute
rating
IEC/EN/DIN
EN 60747-
5-2 Quantity
RoHS
Compliant
Non RoHS
Compliant
HCPL-4534
-000E No option
300mil
DIP-8
50 per tube
-300E -300 X X 50 per tube
-500E -500 X X X 1000 per reel
-020E -020 X 50 per tube
-320E -320 X X X 50 per tube
-520E -520 X X X X 1000 per reel
-060E -060 X 50 per tube
-360E -360 X X X 50 per tube
-560E -560 X X X X 1000 per reel
HCPL-0534 -000E No option SO-8 100 per tube
-500E -500 X X X 1500 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-4534 to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/
EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant.
Example 2:
HCPL-4534 to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.
4
Schematic
Package Outline Drawings
8-Pin DIP Package (HCPL-4534)
1.080 ± 0.320
(0.043 ± 0.013) 2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES).
*MARKING CODE LETTER FOR OPTION NUMBERS.
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
5° TYP. 0.254 + 0.076
- 0.051
(0.010+ 0.003)
- 0.002)
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXXZ
YYWW
DATE CODE
5678
4321
OPTION CODE*
UL
RECOGNITION
UR
TYPE NUMBER
3.56 ± 0.13
(0.140 ± 0.005)
I
F1
8
7
V
CC
+
2
V
O1
I
CC
V
F1
I
O1
1
–
I
F2
6
5
GND
–
4
V
O2
V
F2
I
O2
3
+
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED.
5
Small Outline SO-8 Package (HCPL-0534)
XXX
YWW
8765
4321
5.994 ± 0.203
(0.236 ± 0.008)
3.937 ± 0.127
(0.155 ± 0.005)
0.406 ± 0.076
(0.016 ± 0.003) 1.270
(0.050)BSC
* 5.080 ± 0.127
(0.200 ± 0.005)
3.175 ± 0.127
(0.125 ± 0.005) 1.524
(0.060)
45° X 0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012)MIN.
* TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
0.203 ± 0.102
(0.008 ± 0.004)
7°
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
Package Outline Drawings, continued
8-Pin DIP Package with Gull Wing Surface Mount Option 300 or 500 (HCPL-4534)
0.635 ± 0.25
(0.025 ± 0.010) 12° NOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.016 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 ± 0.320
(0.043 ± 0.013)
3.56 ± 0.13
(0.140 ± 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254 + 0.076
- 0.051
(0.010+ 0.003)
- 0.002)
6
Regulatory Information
The devices contained in this data sheet have been approved by the following organizations:
Solder Reow Thermal Prole
Recommended Pb-Free IR Prole
UL
Recognized under UL 1577, Component Recognition
Program, File E55361.
CSA
Approved under CSA Component Acceptance Notice
#5, File CA 88324.
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01.
(Option 060 only)
0
TIME (SECONDS)
TEMPERATURE (°C)
200
100
50 150100 200 250
300
0
30
SEC.
50 SEC.
30
SEC.
160 °C
140 °C
150 °C
PEAK
TEMP.
245 °C
PEAK
TEMP.
240 °CPEAK
TEMP.
230 °C
SOLDERING
TIME
200 °C
PREHEATING TIME
150 °C, 90 + 30 SEC.
2.5 C ± 0.5 °C/SEC.
3°C+1°C/–0.5 °C
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
PREHEATING RATE 3 °C+1°C/–0.5 °C/SEC.
REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC.
NOTE: NON-HALIDE FLUX SHOULD BE USED.
217 °C
RAMP-DOWN
6°C/SEC. MAX.
RAMP-UP
3°C/SEC. MAX.
150 - 200 °C
260 +0/-5 °C
t 25 °C to PEAK
60 to 150 SEC.
15 SEC.
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
tp
ts
PREHEAT
60 to 180 SEC.
tL
TL
Tsmax
Tsmin
25
Tp
TIME
TEMPERATURE
NOTES:
THE TIME FROM 25 °C to PEAK
TEMPERATURE = 8 MINUTES MAX.
Tsmax = 200 °C, Tsmin = 150 °C
NOTE: NON-HALIDE FLUX SHOULD BE USED.
7
Insulation and Safety Related Specications
8-Pin DIP
(300 Mil) SO-8
Parameter Symbol Value Value Units Conditions
Minimum External L(101) 7.1 4.9 mm Measured from input terminals to output to
Air Gap (External to output terminals, shortest distance through air.
Clearance)
Minimum External L(102) 7.4 4.8 mm Measured from input terminals to output
Tracking (External terminals, shortest distance path along body.
Creepage)
Minimum Internal 0.08 0.08 mm Through insulation distance, conductor to
Plastic Gap conductor, usually the direct distance
(Internal Clearance) between the photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal NA NA mm Measured from input terminals to output
Tracking (Internal terminals, along internal cavity.
Creepage)
Tracking Resistance CTI 200 200 Volts DIN IEC 112/VDE 0303 Part 1
(Comparative
Tracking Index)
Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classication is Class A in accordance with CECC 00802.
8
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (Option 060)
Characteristic
Description Symbol HCPL-4534 HCPL-0534 Unit
Installation classication per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 V rms I-IV
for rated mains voltage ≤ 300 V rms I-IV I-III
for rated mains voltage ≤ 600 V rms I-III I-II
Climatic Classication 55/100/21 55/100/21
Pollution Degree (DIN VDE 0110/1.89) 2 2
Maximum Working Insulation Voltage VIORM 630 567 Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test VPR 1181 1050 Vpeak
with tm = 1 sec, Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and Sample Test, VPR 945 840 Vpeak
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage VIOTM 6000 4000 Vpeak
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(Maximum values allowed in the event of a failure.)
Case Temperature TS 175 175 ˚C
Input Current** IS,INPUT 230 230 mA
Output Power** PS,OUTPUT 600 600 mW
Insulation Resistance at TS, VIO = 500 V RS > 109 > 109 Ω
* Refer to the optocoupler section of the Isolation and Control Components Designer's Catalog, under Product Safety Regulations section,
IEC/EN/DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test proles.
** Refer to the following gure for dependence of PS and IS on ambient temperature.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.
9
Absolute Maximum Ratings
Parameter Symbol Device Min. Max. Units Note
Storage Temperature TS -55 125 °C
Operating Temperature TA -55 100 °C
Average Forward Input Current IF(AVG) 25 mA
(each channel)
Peak Forward Input Current (each channel) IF(PEAK) 50 mA
(50% duty cycle, 1 ms pulse width)
Peak Transient Input Current (each channel) IF(TRANS) 1 A
(≤ 1 µs pulse width, 300 pps)
Reverse LED Input Voltage (each channel) VR 5 V
Input Power Dissipation (each channel) PIN 45 mW
Average Output Current (each channel) IO(AVG) 8 mA
Peak Output Current IO(PEAK) 16 mA
Supply Voltage (Pin 8-5) VCC -0.5 30 V
Output Voltage (Pins 7-5, 6-5) VO -0.5 20 V
Output Power Dissipation (each channel) PO 35 mW 13
Lead Solder Temperature TLS 8 Pin DIP 260 °C
(Through-Hole Parts Only)
1.6 mm below seating plane, 10 seconds
Reow Temperature Prole TRP SO-8 and see Package Outline Drawings
Option 300 section
10
Electrical Specications (DC)
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specied. See note 9.
Parameter Sym. Min. Typ.* Max. Units Test Conditions Fig. Note
Current Transfer
Ratio
CTR 19 24 50 % TA = 25°C IF = 16 mA,
VCC = 4.5 V
VO = 0.5 V
1, 2 1, 2
4
15
Logic Low
Output Voltage
VOL 0.1 0.5 V TA = 25°C IO = 3.0 mA IF = 16 mA,
VCC = 4.5 V
1 1
0.5 IO = 2.4 mA
Logic High
Output Current
IOH 0.003 0.5 µA TA = 25°C, VCC = VO = 5.5V, IF = 0 mA 6 1
50 TA = 25°C, VCC = VO = 15V,
Logic Low
Supply Current
ICCL 100 400 µA IF = 16 mA, VO = Open,
VCC = 15 V
Logic High
Supply Current
ICCH 0.05 4 µA IF = 0 mA, VO = Open,
VCC = 15 V
Input Forward
Voltage
VF1.5 1.7 V TA = 25°C IF = 16 mA 3 1
1.8
Input Reverse
Breakdown Voltage
BVR5 V IR=10 µA 1
Temperature
Coecient of
Forward Voltage
ΔVF
ΔTA
-1.6 mV/
°C
IF = 16 mA
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V
*All typicals at TA = 25°C.
Switching Specications (AC)
Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specied.
Parameter Sym. Min. Typ.* Max. Units Test Conditions Fig. Note
Propagation Delay Time
to Logic Low at Output
tPHL 0.2 0.8 µs TA = 25°C RL = 1.9 kΩ 5, 9,
11
6, 7
1.0
Propagation Delay Time
High to Logic at Output
tPLH 0.6 0.8 µs TA = 25°C RL = 1.9 kΩ 5, 9,
11
6, 7
1.0
Common Mode Transient
Immunity at Logic High Level
Output
|CMH| 15 30 kV/µs RL = 1.9 kΩ, VCM = 10 Vp-p
TA = 25°C
10 5, 6,
7
Common Mode Transient
Immunity at Logic Low Level
Output
|CML| 15 30 kV/µs RL = 1.9 kΩ, VCM = 10 Vp-p
TA = 25°C
10 5, 6,
7
Bandwidth BW 3 MHz RL = 100 kΩ 7, 8
*All typicals at TA = 25°C.
11
Package Characteristics
Parameter Sym. Device Min. Typ.* Max. Units Test Conditions Fig. Note
Input-Output
Momentary With-
stand Voltage**
VISO 3750 V rms RH < 50%,
t = 1 min.,
3, 10
with
Option 020
5000 3, 11
Resistance
(Input-Output)
RI-O 1012 Ω RH ≤45%
VI-O = 500 Vdc,
t = 5 s
3
Capacitance
(Input-Output)
CI-O 0.6 pF f = 1 MHz,
TA = 25°C
12
Input-Input
Insulation
Leakage Current
II-I 0.005 µA RH ≤45%,
t = 5 s,
VI-I = 500 Vdc
4
Resistance
(Input-Input)
RI-I 1011 Ω 4
Capacitance
(Input-Input)
CI-I HCPL-4534 0.03 pF f = 1 MHz 4
HCPL-0534 0.25
* All typicals at TA = 25°C.
** The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specication or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication
number 5963-2203E.
Notes:
1. Each channel.
2. CURRENT TRANSFER RATIO is dened as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.
3. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
4. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common
mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic
Low level is the maximum tolerable (negative) dV
CM/dt on the falling edge of the common mode pulse signal, VCM, to assure that the output
will remain in a Logic Low state (i.e., VO < 0.8 V).
6. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
7. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and the 6.1 kΩ pull-up resistor.
8. The frequency at which the ac output voltage is 3 dB below the low frequency asymptote.
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for 1 second (leakage de-
tection current limit, II-O ≤5 µA).
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (leakage de-
tection current limit, II-O ≤5 µA).
12. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
13. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/ ° C for the SOIC-8 package.
12
Figure 1. DC and pulsed transfer characteristics. Figure 2. Current transfer ratio vs. input current. Figure 3. Input current vs. forward voltage.
HCPL-2530 fig 1
010 20
VO – OUTPUT VOLTAGE – V
IO – OUTPUT CURRENT – mA
10
5
0
T = 25°C
V = 5.0 V
A
CC
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
I = 5 mA
F
HCPL-2530 Figure 2
NORMALIZED
I = 16 mA
V = 0.5 V
V = 5 V
T = 25°C
F
O
CC
A
HCPL-2530/0530
HCPL-2531/0531/4534/0534
1.5
1.0
0.5
0.1
0 1 10 100
NORMALIZED CURRENT TRANSFER RATIO
IF – INPUT CURRENT – mA
HCPL-2530 fig 3
V
F
– FORWARD VOLTAGE – VOLTS
100
10
0.1
0.01
1.1 1.2 1.3 1.4
I
F
– FORWARD CURRENT – mA
1.61.5
1.0
0.001
1000
I
F
V
F
+T = 25°C
A
–
Figure 4. Current transfer ratio vs. temperature. Figure 5. Propagation delay vs. temperature. Figure 6. Logic high output current vs. tempera-
ture.
HCPL-2530 fig 6
-50 +50
TA – TEMPERATURE – °C
IOH – LOGIC HIGH OUTPUT CURRENT – nA
10-2
-25 0 +25 +75 +100
10-1
10 0
10+1
10+2
10+3
10+4
VO = VCC = 5.0 V
IF = 0
HCPL-2530 Figure 4
1.1
1.0
0.9
0.8
0.7
0.6
-60 -20 0 80
NORMALIZED CURRENT TRANSFER RATIO
TA – TEMPERATURE – °C
F
CC
A
-40 20 40 60 100
O
NORMALIZED
I = 16 mA
V = 0.5 V
V = 5 V
T = 25°C
HCPL-2530/0530
HCPL-2531/0531/4534/0534
2000
1500
1000
500
0
-60 -20 20 60 100
T
A
– TEMPERATURE – °C
t
P
– PROPAGATION DELAY – ns
t
PHL
t
PLH
I
F
= 16 mA, V
CC
= 5.0 V
HCPL-2530/0530 (R
L
= 4.1 kΩ)
HCPL-2531/0531/4534/0534
(R
L
= 1.9 kΩ)
Figure 7. Small-signal current transfer ratio vs.
quiescent input current.
HCPL-2530 Figure 7
∆
I
F
∆
I
O
– SMALL SIGNAL CURRENT TRANSFER RATIO
0
0.10
0.20
0.30
0
I
F
– QUIESCENT INPUT CURRENT – mA
24
164 8 12 20
T
A
= 25°C, R
L
= 100 Ω, V
CC
= 5 V
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved.
AV02-1374EN - June 27, 2008
Figure 8. Frequency response.
Figure 9. Switching test circuit.
V
O
PULSE
GEN.
Z = 50 Ω
t = 5 ns
O
r
I MONITOR
F
I
F
0.1µF
L
R
C
L
= 1.5 pF
R
M
0
t
PHL
t
PLH
O
V
I
F
OL
V
1.5 V
+5 V
1.5 V
5 V 10% DUTY CYCLE
1/f < 100 µs
7
1
2
3
45
6
8
f – FREQUENCY – MHz
0
-20
0.01 0.1
NORMALIZED RESPONSE –dB
1.0
-25
10
-30
TA= 25 C
IF= 16 mA
-15
-10
-5
RL= 100 Ω
RL= 220 Ω
RL= 470 Ω
RL= 1 kΩ
1
2
3
4
8
7
6
5
20 kΩ
SET IF
+5 V
AC INPUT
0.1 µF
560 Ω100 Ω
2N3053
1.6 V dc
0.25 Vp-p ac
0.1 µF
+5 V
VO
RL
Figure 10. Test circuit for transient immunity and typical waveforms.
O
V5 V
OL
V
O
V
0 V 10% 90% 90% 10%
SWITCH AT A: I = 0 mA
F
SWITCH AT B: I = 16 mA
F
CM
V
t
r
t
f
V
O
I
F
0.1 µF
L
R
+5 V
A
B
PULSE GEN.
V
CM
+–
V
FF
7
1
2
3
45
6
8
HCPL-2530 Figure 11
3.0
2.0
1.0
0.1
4
0.6
0.4
321
0.2
8765 9 10
0.8
R
L
– LOAD RESISTANCE – kΩ
t
PLH
t
PHL
V = 5.0 V
T = 25 °C
CC
I = 10 mA
I = 16 mA
F
t
P
– PROPAGATION DELAY – µs
F
A
Figure 11. Propagation delay time vs. load
resistance.