Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ). It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 13 CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE) CHIP BEAD INDUCTORS FOR POWER LINES FB SERIES M TYPE WAVE REFLOW PARTS NUMBER F B M J 3 2 1 6 H Series name Code FB S 8 0 0 Shape Rectangular chip FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Characteristics Code J H Nominal impedance Code example 330 111 132 Characteristics Standard High Impedance type DimensionsLxW Code Typeinch 1608 2125 2012 2016 3216 3225 4516 4525 4532 16080603 21250805 20120805 20160806 32161206 32251210 45161806 45251810 45321812 Blank space Material Code HS HM HL Series name Ferrite bead Shape Code M T Impedance tolerance Code N Dimensions LxWmm 1.6x0.8 2.0x1.25 Material Refer to impedance curves for material differences Nominal impedance 33 110 1300 Impedance tolerance 25 30 Packaging Code T 2.0x1.6 3.2x1.6 3.2x2.5 4.5x1.6 4.5x2.5 4.5x3.2 Packaging Taping Internal code Code Internal code Standard STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to these products is reflow soldering only. Type L W T e FB MJ1608 0603 FB MJ2125 0805 FB MJ3216 1206 FB MJ4516 1806 FB MH1608 0603 FB MH2012 0805 FB MH2016 0806 FB MH3216 1206 FB MH3225 1210 FB MH4516 1806 FB MH4525 1810 FB MH4532 1812 1.60.2 0.0630.008 2.00.2 0.0790.008 3.20.3 0.1260.012 4.50.3 0.1770.012 1.60.1 0.0630.004 2.00.2 0.0790.008 2.00.2 0.0790.008 3.20.3 0.1260.012 3.20.3 0.1260.012 4.50.3 0.1770.012 4.50.4 0.1770.016 4.50.4 0.1770.016 0.80.2 0.0310.008 1.250.2 0.0490.008 1.60.2 0.0630.008 1.60.2 0.0630.008 0.80.1 0.0310.004 1.250.2 0.0490.008 1.60.2 0.0630.008 1.60.2 0.0630.008 2.50.3 0.0980.012 1.60.2 0.0630.008 2.50.3 0.0980.012 3.20.3 0.1260.012 0.80.2 0.0310.008 0.850.2 0.0330.008 1.10.2 0.0430.008 1.10.2 0.0430.008 0.80.1 0.0310.004 0.850.2 0.0330.008 1.60.2 0.0630.008 1.60.2 0.0630.008 2.50.3 0.0980.012 1.60.2 0.0630.008 2.50.3 0.0980.012 3.20.3 0.1260.012 0.30.2 0.0120.008 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.30.15 0.0120.006 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.50.3 0.0200.012 0.90.6 0.0350.024 0.90.6 0.0350.024 Type FB MJ1608 FB MJ2125 FB MJ3216 FB MJ4516 FB MH1608 FB MH2012 FB MH2016 FB MH3216 FB MH4516 FB MH3225 FB MH4525 FB MH4532 A 1.0 1.4 1.4 1.75 1.0 1.4 1.4 1.4 1.75 1.4 1.75 1.75 B 1.0 1.2 2.2 3.5 1.0 1.2 1.2 2.2 3.5 2.2 3.5 3.5 C 1.0 1.65 2.0 2.0 1.0 1.65 2.0 2.0 2.0 2.9 2.9 3.7 Unitmm Standard quantity [pcs ] Paper tape Embossed tape 4000 4000 2000 2000 4000 4000 2000 2000 1000 2000 1000 2000 Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 104 13 PARTS NUMBER Standard type FB MJ1608 Parts number FB MJ1608HS280NT FB MJ1608HM230NT EHS RoHS RoHS Nominal impedance 28 23 Impedance tolerance 30 30 Measuring frequency MHz 100 100 DC Resistance max. 0.007 0.007 Rated current Amax. 4.0 4.0 Thickness mm 0.8 0.2 0.8 0.2 Measuring frequency MHz 100 100 100 100 100 DC Resistance max. 0.008 0.004 0.008 0.004 0.008 Rated current Amax. 4.0 6.0 4.0 6.0 4.0 Thickness mm 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 Measuring frequency MHz 100 100 100 100 100 DC Resistance max. 0.010 0.005 0.010 0.005 0.012 Rated current Amax. 4.0 6.0 4.0 6.0 4.0 Thickness mm 1.1 0.2 1.1 0.2 1.1 0.2 1.1 0.2 1.1 0.2 Measuring frequency MHz 100 100 100 100 100 DC Resistance max. 0.014 0.007 0.014 0.007 0.014 Rated current Amax. 4.0 6.0 4.0 6.0 3.5 Thickness mm 1.1 0.2 1.1 0.2 1.1 0.2 1.1 0.2 1.1 0.2 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.020 0.025 0.035 0.050 0.070 0.130 0.150 0.170 0.350 0.028 0.045 0.130 0.170 0.210 0.350 0.450 Rated current Amax. 3.5 3.0 2.0 2.0 1.5 0.9 0.7 0.7 0.5 2.5 1.8 0.9 0.7 0.6 0.5 0.4 Thickness mm 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 0.8 0.1 Measuring frequency MHz 100 100 100 100 DC Resistance max. 0.025 0.032 0.060 0.080 Rated current Amax. 2.7 2.5 2.0 1.8 Thickness mm 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 Measuring frequency MHz 100 100 DC Resistance max. 0.015 0.050 Rated current Amax. 4.5 2.0 Thickness mm 1.6 0.2 1.6 0.2 Measuring frequency MHz 100 100 DC Resistance max. 0.020 0.070 Rated current Amax. 4.0 2.0 Thickness mm 1.6 0.2 1.6 0.2 Measuring frequency MHz 100 100 100 DC Resistance max. 0.042 0.100 0.130 Rated current Amax. 3.0 2.0 1.2 Thickness mm 2.5 0.3 2.5 0.3 2.5 0.3 FB MJ2125 FB FB FB FB FB Parts number EHS MJ2125HS420-T MJ2125HS250NT MJ2125HM330-T MJ2125HM210NT MJ2125HL8R0NT RoHS RoHS RoHS RoHS RoHS Nominal impedance 42 25 33 21 8 Impedance tolerance 25 30 25 30 30 FB MJ3216 EHS MJ3216HS800-T MJ3216HS480NT MJ3216HM600-T MJ3216HM380NT MJ3216HL160NT RoHS RoHS RoHS RoHS RoHS Nominal impedance 80 48 60 38 16 Impedance tolerance 25 30 25 30 30 FB MJ4516 FB FB FB FB FB Parts number EHS MJ4516HS111-T MJ4516HS720NT MJ4516HM900-T MJ4516HM560NT MJ4516HL230NT RoHS RoHS RoHS RoHS RoHS Nominal impedance 110 72 90 56 23 Impedance tolerance 25 30 25 30 30 High impedance type FB MH1608 Parts number FB MH1608HM470-T FB MH1608HM600-T FB MH1608HM101-T FB MH1608HM151-T FB MH1608HM221-T FB MH1608HM331-T FB MH1608HM471-T FB MH1608HM601-T FB MH1608HM102-T FB MH1608HL300-T FB MH1608HL600-T FB MH1608HL121-T FB MH1608HL221-T FB MH1608HL331-T FB MH1608HL471-T FB MH1608HL601-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 47 60 100 150 220 330 470 600 1000 30 60 120 220 330 470 600 Impedance tolerance 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 FB MH2012 FB FB FB FB Parts number EHS MH2012HM800-T MH2012HM121-T MH2012HM221-T MH2012HM331-T RoHS RoHS RoHS RoHS Nominal impedance 80 120 220 330 Impedance tolerance 25 25 25 25 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS FB FB FB FB FB Parts number FB MH2016 Parts number FB MH2016HM121NT FB MH2016HM251NT EHS RoHS RoHS Nominal impedance 120 250 Impedance tolerance 30 30 FB MH3216 Parts number FB MH3216HM221NT FB MH3216HM501NT EHS RoHS RoHS Nominal impedance 220 500 Impedance tolerance 30 30 FB MH3225 Parts number FB MH3225HM601NT FB MH3225HM102NT FB MH3225HM202NT EHS RoHS RoHS RoHS Nominal impedance 600 1000 2000 Impedance tolerance 30 30 30 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 13 105 PARTS NUMBER FB MH4516 Parts number FB MH4516HM851NT EHS RoHS Nominal impedance 850 Impedance tolerance 30 Measuring frequency MHz 100 DC Resistance max. 0.100 Rated current Amax. 1.5 Thickness mm 1.6 0.2 Measuring frequency MHz 100 100 DC Resistance max. 0.060 0.130 Rated current Amax. 3.0 2.0 Thickness mm 2.5 0.3 2.5 0.3 Measuring frequency MHz 100 100 100 DC Resistance max. 0.028 0.060 0.130 Rated current Amax. 4.0 3.0 1.3 Thickness mm 3.2 0.3 3.2 0.3 3.2 0.3 Measuring frequency MHz 100 100 100 100 DC Resistance max. 0.004 0.006 0.004 0.006 Rated current Amax. 7.5 6.0 7.5 6.0 Thickness mm 0.8 0.2 0.8 0.2 0.8 0.2 0.8 0.2 FB MH4525 Parts number FB MH4525HM102NT FB MH4525HM162NT EHS RoHS RoHS Nominal impedance 1000 1600 Impedance tolerance 30 30 FB MH4532 Parts number FB MH4532HM681-T FB MH4532HM132-T FB MH4532HM202-T EHS RoHS RoHS RoHS Nominal impedance 680 1300 2000 Impedance tolerance 25 25 25 High current type Parts number FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS FB FB FB FB MJ1608HS220NTR MJ1608HS280NTR MJ1608HM180NTR MJ1608HM230NTR EHS RoHS RoHS RoHS RoHS Nominal impedance 22 28 18 23 Impedance tolerance 30 30 30 30 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 106 13 ELECTRICAL CHARACTERISTICS FBMJ1608 FBMJ2125 FBMJ3216 60 50 40 30 20 10 0 FBMJ4516 FBMJ4516HL230NT 100 90 80 70 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS FBMJ3216HL160NT 70 60 50 40 30 20 10 0 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 13 107 ELECTRICAL CHARACTERISTICS Standard type FBMH1608 FBMH1608HM470-T 200 FBMH1608HM600-T 200 180 180 160 160 160 140 140 140 120 120 120 100 100 100 80 80 Z 60 X 20 0 1 10 600 100 10000 FBMH1608HM221-T FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS R 100 1000 10000 FBMH1608HM102-T 1200 Z 1000 800 X 1000 10 10000 FBMH1608HM471-T 100 1600 1400 1200 1200 1000 1000 10000 FBMH1608HL300-T 250 200 150 X 100 200 1000 10000 FBMH1608HL221-T Z R 100 1000 FBMH1608HL600-T 10 100 1000 10000 R X 10 100 1000 10000 FBMH1608HL121-T 500 Z 400 R 150 300 100 200 0 1 10 100 1000 10000 FBMH1608HL471-T 2000 300 Z R 1000 10000 0 100 1000 10000 FBMH1608HL601 2500 Z 1500 R 1000 800 R 1000 600 X 400 X 200 100 10 Z 1200 400 X 200 0 1 2000 1400 600 400 X 1800 800 Z R 100 FBMH1608HL331-T 1000 R 100 0 1 600 1600 700 10 Z X 1200 800 500 10000 FBMH1608HM601-T 200 10000 50 X 0 1 1400 900 600 1000 400 X 10 300 200 100 600 R 0 1 250 10 800 Z 400 1000 X 0 1 1400 200 0 1 R 100 100 800 R 50 10 10 Z 600 400 0 1 600 300 1400 R 100 X 1600 100 X 10 Z 200 100 0 1 10000 FBMH1608HM331-T 300 Z 200 1000 1000 400 300 0 1 100 Z 200 20 500 400 1600 10 600 500 0 1 0 1 300 R 40 X 20 1000 400 Z 60 R 40 FBMH1608HM151-T 600 500 80 Z 60 R 40 FBMH1608HM101-T 200 180 500 X 200 1 10 100 1000 10000 0 1 10 100 1000 10000 0 1 10 100 1000 10000 FBMH2012 400 FBMH2012HM800-T 400 FBMH2012HM121-T 350 350 300 300 300 250 250 250 200 200 200 150 100 10 100 1000 10000 0 1 100 1000 10000 FBMH2016 200 400 R X 200 X 0 1 10 100 1000 10000 0 1 10 100 1000 10000 FBMH3216 FBMH2016HM121NT 800 FBMH2016HM251NT 350 180 FBMH3216HM221NT 800 FBMH3216HM501NT 300 160 600 120 200 Z 100 R 400 Z 60 X 100 1000 10000 0 1 10 Z 400 R 100 X 100 200 50 X 20 R R 200 40 Z 150 80 10 600 250 140 0 1 Z R 50 X 10 FBMH2012HM331-T 600 Z 100 50 X 800 150 R 100 R 50 0 1 Z 150 Z FBMH2012HM221-T 400 350 1000 0 1 X 10 100 1000 10000 0 1 10 100 1000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 108 13 ELECTRICAL CHARACTERISTICS Standard type FBMH3225 1200 FBMH4516 FBMH3225HM601NT 1200 1000 1000 800 800 600 600 Z 400 1200 2500 Z R Z 1000 100 400 0 1 10 100 1000 0 1 10 100 0 1 1000 10 100 1000 FBMH4532 FBMH4525HM102NT FBMH4525HM162NT FBMH4532HM681-T FBM4532HM132-T 1800 1800 1800 1600 1600 1600 1600 1400 1400 1400 1400 1000 1000 1000 1000 1200 1200 1200 1200 Z 800 Z 800 R 600 R 800 600 400 400 X 200 10 100 0 Z 400 X 200 1000 800 600 R 200 1 10 100 1000 0 400 10 100 X 200 X 1 R Z 600 0 1000 1 10 100 1000 High current type FBM4532HM202-T 2500 30 J1608HS220NTR 40 J1608HM180NTR 35 25 2000 30 20 1500 Z 25 Z 1000 Z 20 R 15 R R 15 10 10 500 X 5 0 1 10 100 1000 0 1 10 100 X 5 X 1000 0 1 10000 10 100 1000 10000 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 1800 1 X 200 X FBMH4525 0 Z 600 500 X 200 1000 R 800 1500 R FBMH4516HM851NT 1000 2000 400 X 10 FBMH3225HM202NT R 200 0 1 FBMH3225HM102NT This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 13 109 CHIP BEAD INDUCTORS FOR POWER LINES (FB SERIES M TYPE) PACKAGING Minimum Quantity Type 16080603 21250805 20120805 20160806 32161206 45161806 32251210 45251810 45321812 Standard Quantitypcs Paper Tape Embossed Tape 4000 4000 4000 2000 2000 2000 1000 1000 2000 Tape Material Card board carrier tape Embossed Tape Taping Dimensions Paper tape (0.315 inches wide) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_pack_e-01 A Chip Cavity B Insertion Pitch F Tape Thickness T 1.00.2 0.0390.008 1.80.2 0.0710.008 4.00.2 0.1570.008 1.1max 0.043max 1.50.2 0.0590.008 2.30.2 0.0910.008 4.00.2 0.1570.008 1.1max 0.043max Type FBMJ1608 FBMH1608 0603 FBMJ2125 FBMH2012 0805 Unit : mminch Embossed tape (0.315 inches wide) Type FBMH2016 0806 FBMJ3216 1206 FBMH3216 1206 FBMH3225 1210 Chip Cavity A B 1.80.2 2.20.2 0.0710.008 0.0870.008 1.90.2 3.50.2 0.0750.008 0.1380.008 1.90.2 3.50.2 0.0750.008 0.1380.008 2.80.2 3.50.2 0.1100.008 0.1380.008 Insertion Pitch F 4.00.2 0.1570.008 4.00.2 0.1570.008 4.00.2 0.1570.008 4.00.2 0.1570.008 Tape Thickness K T 2.6max 0.6max 0.102max 0.024max 1.5max 0.3max 0.059max 0.012max 2.6max 0.6max 0.102max 0.024max 4.0max 0.6max 0.157max 0.024max Unit : mminch Insertion Pitch F 4.00.2 0.1570.008 4.00.2 0.1570.008 4.00.2 0.1570.008 8.00.2 0.3150.008 Tape Thickness K T 1.5max 0.3max 0.059max 0.012max 2.6max 0.6max 0.102max 0.024max 4.0max 0.6max 0.157max 0.024max 4.0max 0.6max 0.157max 0.024max Unit : mminch Embossed tape (0.472 inches wide) Type FBMJ4516 1806 FBMH4516 1806 FBMH4525 1810 FBMH4532 1812 Chip Cavity A B 1.90.2 4.90.2 0.0750.008 0.1930.008 1.90.2 4.90.2 0.0750.008 0.1930.008 2.90.2 4.90.2 0.1140.008 0.1930.008 3.60.2 4.90.2 0.1420.008 0.1930.008 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_pack_e-01 Leader and Blank portion Reel size Type FBMJ1608 FBMJ2125 FBMJ3216 A B 10.01.5 0.3940.047 14.01.5 0.5510.059 FBMJ4516 FBMH1608 FBMH2012 FBMH2016 FBMH3216 FBMH3225 FBMH4516 FBMH4525 FBMH4532 W 1800/3 7.090/0.118 3302.0 12.990.080 601/0 2.360.039/0 1001.0 3.940.039 10.01.5 0.3940.047 14.01.5 0.5510.059 142.0 0.5510.080 Unit : mminch Top tape strength The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow as illustrated below. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_pack_e-01 CHIP BEAD INDUCTORS FOR POWER LINE (FB SERIES M TYPE) RELIABILITY DATA 1. Operating Temperature Range Specified Value 40125 Including self-generated heat 2. Storage Temperature Range Specified Value 4085 Test Methods and Remarks *Note: 0 to 40 in taped packaging 3. Impedance Specified Value Within the specified tolerance Test Methods and Remarks Measuring equipment Measuring frequency : Impedance analyzer (HP4291A) or its equivalent : 1001 MHz 4. DC Resistance Specified Value Within the specified range Test Methods and Remarks Four-terminal method Measuring equipment : Milliohm High-Tester 3226 (Hioki Denki) or its equivalent 5. Rated Current Specified Value Within the specified range 6. Vibration Specified Value Appearance Impedance change : No significant abnormality : Within 30% of the initial value Test Methods and Remarks According to JIS C 0040. Vibration type :A Time : 2 hrs each in X,Y, and Z directions Total: 6 hrs Frequency range : 10 to 55 to 10Hz (/min.) Amplitude : 1.5 mm (shall not exceed acceleration 196m/s2) Mounting method : Soldering onto PC board 7. Solderability Specified Value 90% or more of immersed surface of terminal electrode shall be covered with fresh solder. Test Methods and Remarks Solder temperature Immersion time Preconditioning Immersion and Removal speed : : : : 2305 41 sec. Immersion into flux. 25mm/sec. 8. Resistance to Soldering Heat Specified Value Appearance Impedance change : No significant abnormality : Within 30% of the initial value Test Methods and Remarks Preheating Resistance to Soldering Heat Duration Preconditioning Immersion and Removal speed Recovery : : : : : : 150 for 3 min. 2605 100.5 sec. Immersion into flux. 25mm/sec. 2 to 3 hrs of recovery under the standard condition after the test. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_reli_e-01 9. Thermal Shock Specified Value Test Methods and Remarks Appearance Impedance change : No significant abnormality : Within50/10% of the initial value According to JIS C 0025. Conditions for 1 cycle Sep Temperature () 1 403 2 Room Temperature 3 852 4 Room Temperature Number of cycles Mounting method Recovery Duration (min.) 303 Within 3 303 Within 3 : 100 : Soldering onto PC board : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 10. Resistance to Humidity (steady state) Specified Value Appearances Impedance change : No significant abnormality : Within 30% of the initial value Test Methods and Remarks Temperature Humidit Duration Mounting method Recovery : 402 : 90 to 95% RH : 50024/0 : Soldering onto PC board : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 11. Loading under Damp Heat Specified Value Appearance Impedance change Test Methods and Remarks Temperature Humidity Applied current Duration Mounting method Recovery No significant abnormality Within 30% of the initial value : 402 : 90 to 95%RH : Rated current : 50024/0 hrs : Soldering oto PC board : 2 to 3hrs of recovery under the standard condition after the removal from test chamber. 12. High Temperature Loading Test Specified Value Appearance Impedance change : No significant abnormality : Within 30% of the initial value Test Methods and Remarks Temperature Duration Applied current Mounting method Recovery : : : : : 852 50024/0 hrs Rated current Soldering onto PC board 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 13. Bending Strength Specified Value Appearance : No mechanical damage. Warp Testing board Thickness : 2mm : Glass epoxy-resin substrate : 0.8mm Test Methods and Remarks This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_reli_e-01 14. Adhesion of Electrode Specified Value No separation or indication of separation of electrode. Applied force Duration : 5N : 10 sec. Test Methods and Remarks Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35 of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 202 of temperature, 60 to 70% relative humidity and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_reli_e-01 CHIP BEAD INDUCTORS FOR POWER LINE FB SERIES M TYPE PRECAUTIONS 1. Circuit Design Precautions Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. Rated current 1. Rated current of this product is shown in this catalogue, but please be sure to have the base board designed with adequate inspection in case of the generation of heat becomes high within the rated current range when the base board is in high resistance or in bad heating conditions. 2. PCB Design Precautions Land pattern design 1. Please refer to a recommended land pattern. 3. Considerations for automatic placement Precautions Technical considerations Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, etc. sufficiently. Preheating when soldering Heating : The temperature difference between soldering and remaining heat should not be greater than 150. Cooling : The temperature difference between the components and cleaning process should not be greater than 100. Recommended conditions for using a soldering iron Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration - 3 seconds or less The soldering iron should not directly touch the inductor. Wave, Reflow, Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. Technical considerations Preheating when soldering 1. There is a case that products get damaged by a heat shock. Recommended conditions for using a soldering iron 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_prec_e-01 5. Handling Precautions Technical considerations Handling 1. Keep the inductors away from all magnets and magnetic objects. Setting PC boards 1. When setting a chip mounted base board, please make sure that there is no residual stress to the chip by distortion in the board or at screw part. Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. Handling 1. There is a case that a characteristic varies with magnetic influence. Setting PC boards 1. There is a case that a characteristic varies with residual stress. Breakaway PC boards (splitting along perforations) 1. Planning pattern configurations and the position of products should be carefully performed to minimize stress. Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 6. Storage conditions Precautions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature 040 Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within 6 months from the time of delivery. Technical considerations Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . chipbeads_prec_e-01