A
5 Watt HW Single Series DC/DC Converters
2401 Stanwell Drive • Concord, California 94520 • Ph: 925/687-4411 or 800/542-3355 • Fax: 925/687-3333 • www.calex.com • Email: sales@calex.com
4eco#: 030327-1, eco#: 031113-4, eco# 041007-1, 060406-2
snoitacificepSlareneG
sledoMllAstinU
noitalosI
egatloVnoitalosI S42,S21tuptuOottupnI S84tuptuOottupnI egakaeLAµ01
NIM NIM 007 4451 CDV
tuptuOottupnI ecnaticapaC PYT0051Fp
latnemnorivnE
egnaRgnitarepOesaC gnitareDoN NIM XAM 04- 09 C°
)9(egnaRlanoitcn
uFesaC NIM XAM 04- 001 C°
egnaRegarotS NIM XAM 55- 501 C°
)8(ecnadepmIlamrehTPYT03ttaW/C°
lareneG
thgieWtinUPYT44.0zo
slav
orppAycnegA ,LuC,0591LU gnidnep)VUT(05906NE
FBTMsruoHM1>
Mechanical tolerances unless otherwise noted:
X.XX dimensions: ±0.020 inches
X.XXX dimensions: ±0.010 inches
Pin location shown is for the mating PCB
niPnoitcnuF
1TUPNI+
01TUPTUO-
11TUPTUO+
21TUPNI-
31TUPNI-
41TUPTUO+
51TUPTUO-
42TUPNI+
NOTES:
(1) All parameters measured at Tc=25°C, nominal input voltage
and full rated load unless otherwise noted. Refer to the
CALEX Application Notes for the definition of terms.
(2) Output Noise is measured with a 1µF tantalum capacitor and a
0.01µF ceramic capacitor across the output. The fundamental
component of noise is at the switching frequency and also is
commonly referred to as ripple.
(3) External fusing should be used for system protection due to a
catastrophic failure. See CALEX Application Note 9 in the Calex
DC/DC Catalog to determine correct fuse.
(4) Load Transient Overshoot is the output voltage peak amplitude
referenced to the final value due to a step load change of 50-75%
occurring only on the measured output. “Load Transient
Overshoot” and “Dynamic Response” are the same specification.
Load Transient Recovery Time is the time for the output to return
to within specified voltage error band centered about the final
value. “Load Transient Recovery Time” and “ Transient Response”
are the same specification.
(5) Temperature coefficient is defined for case temperatures. Output
voltage deviation is calculated as the maximum resulting from
either 1) 25°C case to maximum operating case temperature, or
2) 25°C case to minimum operating case temperature.
(6) Below the minimum rated load, the output may exhibit noise
performance degradation. Operation with less than minimum
rated load will not damage the unit, and the DC regulation is not
significantly affected.
(7) The case thermal impedance is specified and the case
temperature rise over ambient per package watt dissipated.
(8) Case functional temperature range is intended to give an
additional data point for use is evaluating this power supply. At
the low functional temperature the power supply will function
with no side effects, however, sustained operation at the high
functional temperature will reduce expected operational life.
The data sheet specifications are not guaranteed over the
functional temperature range.
(9) Specifications subject to change without notice.
(10) Water Washability - Calex DC/DC converters are designed to
withstand most solder/wash processes. Careful attention should
be used when assessing the applicability in your specific
manufacturing process. Converters are not hermetically sealed.
Mechanical Outline and
Connector Pin Assignments
0.03
0.90
0.10
0.18
0.40
0.12 Min.
0.16 Max
SIDE VIEW
0.020Ø
1
24
10 11 12
15 1413
1.25
0.60
0.80
BOTTOM VIEW