Y92E-BC12 - OMRON - Product.Network

New Product

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Global standard size,

low profile slim I/O relay with width 6.2 mm,

slim I/O solid state relay

• Realized about 25% lower profile than conventional

products, contributing to further miniaturization of the

control panel.

• Push-In Plus technology are used to save wiring work in

comparison with conventional screw terminals.

(Wiring time is reduced by 60%* in comparison with

traditional screw terminals.)

• No screw loosening means maintenance-free application,

realizing high reliability

• ‘Hand-free’ structure that holds an inserted flat-blade

screwdriver to achieve easier wiring work for stranded

wires.

• Screw terminal is also stocked to meet the screw type

needs.

• Mounted relay or solid-state relay has a plug-in terminal

that is difficult to bend at the time of exchange.

*According to OMRON actual measurement data from November 2015.

Slim I/O Relay Types

G2RV-SR series mounted relay: electromagnetic relay ......from page 2

G3RV-SR series mounted relay: solid state relay ................from page 10

Common matter

Common precautions................................................................ from page 20

Common accessories (order separately).................................from page 25

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

Refer to Safety Precautions on page 20.

Slim I/O Relay

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Slim I/O Relay

G2RV-SR

Global standard size, low profile slim

I/O relay with width 6.2 mm

• Realized about 25% lower profile than conventional

products, contributing to further miniaturization of the

control panel.

• Realized opening and closing ability with one pole 6 A slim

shape.

• Micro load products for one pole 50 mA using Au-plated

contacts for small load switching also available.

• Since G2RV is a transparent case, confirming the state of

the contact with the naked eye is possible, and easy to

confirm abnormality on-site (installed location).

• Screw terminal is also stocked to meet the screw type

needs.

• Mounted relay uses plug-in terminals that are difficult to

bend when exchanging.

• G3RV-SR featuring a solid state relay similar in shape to G2RV-SR also available.

Features

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

Refer to Safety Precautions on page 20.

Transparent case

Relay contact

Release lever

Plug-in terminal

90 mm

80 mm

Peace of mind as the

terminal does not bend

when replacing

Easy confirmation

of the situation

Relay easily

fixed/removed

PAT

Terminal x 5

• Push-in

• Screw

Mechanical

indicator

Release lever

Operation

display LED

(Socket section)

• Operation

verification

which is linked

to the contact

Standard model/Micro load With latching lever

(Test switch)

Latching lever

(Test switch)

• Circuit check operation

Confirmation, reducing the inspection effort

Latching lever

(Test switch)

Protective cover

(Released state)

Push-In Plus technology

Short bar insertion holes

Terminal (insertion) hole

Release hole

Protective cover

(Locked condition)

"Foreign matter intrusion prevention structure"

"Malfunction prevention stopper"

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Model Number Structure

Model Number Legend

Ordering Information

Note: Sockets are not sold individually.

Terminal

(Wire connection) Classification Latching lever

(Test switch) Rated input voltage (V) Model

Push-In Plus

Terminal

Standard

DC 12 G2RV-SR500 DC12

24 G2RV-SR500 DC24

AC/DC 24 G2RV-SR500 AC/DC24

48 G2RV-SR500 AC/DC48

100 G2RV-SR500 AC100

110 G2RV-SR500 AC110

200 G2RV-SR500 AC200

230 G2RV-SR500 AC230

Yes DC 24 G2RV-SR501 DC24

AC/DC 24 G2RV-SR501 AC/DC24

Microloads No

DC 12 G2RV-SR500-AP DC12

24 G2RV-SR500-AP DC24

AC/DC 24 G2RV-SR500-AP AC/DC24

48 G2RV-SR500-AP AC/DC48

100 G2RV-SR500-AP AC100

110 G2RV-SR500-AP AC110

200 G2RV-SR500-AP AC200

230 G2RV-SR500-AP AC230

Screw terminal

Standard

DC 12 G2RV-SR700 DC12

24 G2RV-SR700 DC24

AC/DC 24 G2RV-SR700 AC/DC24

48 G2RV-SR700 AC/DC48

100 G2RV-SR700 AC100

110 G2RV-SR700 AC110

200 G2RV-SR700 AC200

230 G2RV-SR700 AC230

Yes DC 24 G2RV-SR701 DC24

AC/DC 24 G2RV-SR701 AC/DC24

Microloads No

DC 12 G2RV-SR700-AP DC12

24 G2RV-SR700-AP DC24

AC/DC 24 G2RV-SR700-AP AC/DC24

48 G2RV-SR700-AP AC/DC48

100 G2RV-SR700-AP AC100

110 G2RV-SR700-AP AC110

200 G2RV-SR700-AP AC200

230 G2RV-SR700-AP AC230

G2RV-SR @@ @ - @ @

(1) (2) (3) (5) (6)(4)

(1) Basic model name

G2RV: Slim I/O Relay

(2) Sub type

SR: Slim relay + integrated low profile socket

(3) Terminal (wire connection)

50: Push-In Plus Terminal

70: Screw terminal

(4) Latching lever (test switch)

0: Without latching lever

1: With latching lever

(5) Contact structure

Blank: Standard

AP: Microloads

(6) Rated input voltage

12, 24 VDC

24, 48 VAC/VC

100, 110, 200, 230 VAC

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Relay for Maintenance

Model Number Legend

List of Models

Note: Voltage is reduced within the socket for the slim I/O relay, so the rated input voltage and rated coil voltage of replacement relays are different.

Accessories (order separately)

Refer to page 25 for G2RV-SR/G3VR-SR Common Accessories.

(1) No. of poles

1: 1 pole

(2) Terminal

S: plug-in

(3) Latching lever (Test switch)

Blank: Without latching lever

I: With latching lever

(4) Contact material

Blank: Ag alloy

AP: Ag alloy + Au plating

(5) Types of relay for exchange

G: G2RV-SR series equipped

Relay

(6) Rated coil voltage

Number: 11, 21, 48 VDC

(1) (2) (3) (5) (6)(4)

G2RV-1 - S @ - @ - G @

G2RV-1-SI-G G2RV-1-S(-AP)-G

Type Latching

Lever

(Test switch)

Rated coil

voltage (V) Model Applicable model

Standard

No DC

11 G2RV-1-S-G DC11 G2RV-SR700/500 DC12V

21 G2RV-1-S-G DC21 G2RV-SR700/500 DC24V

G2RV-SR700/500 AC/DC24V

48 G2RV-1-S-G DC48

G2RV-SR700/500 AC/DC48V

G2RV-SR700/500 AC100V

G2RV-SR700/500 AC110V

G2RV-SR700/500 AC200V

G2RV-SR700/500 AC230V

Yes DC 21 G2RV-1-SI-G DC21 G2RV-SR701/501 DC24V

G2RV-SR701/501 AC/DC24V

Microload

No DC

11 G2RV-1-S-AP-G DC11 G2RV-SR700/500-AP DC12V

21 G2RV-1-S-AP-G DC21 G2RV-SR700/500-AP DC24V

G2RV-SR700/500-AP AC/DC24V

48 G2RV-1-S-AP-G DC48

G2RV-SR700/500-AP AC/DC48V

G2RV-SR700/500-AP AC100V

G2RV-SR700/500-AP AC110V

G2RV-SR700/500-AP AC200V

G2RV-SR700/500-AP AC230V

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Specifications

Ratings

Coil ratings

Note: The operating characteristics are measured at ambient temperature of 23°C.

*Operating voltage will be, for mounting in the upside down direction, 85% max.

(Upside down: Direction in which the mechanical indicator faces down)

Contact ratings

*1. P level: λ60=0.1×10-6/times

This value is the value in switching frequency 120 operations/min.

*2. If the Au plating layer is destroyed, the number will be the same as the standard type.

Characteristics

Note: Above values are initial values.

*Value is at ambient temperature of 23°C.

Rated input

voltage

Rated current Must operate

voltage Must release

voltage Power consumption Maximum

allowable voltage

AC DC Percentage of the rated voltage AC (VA) DC (mW) Percentage of the

rated voltage

50 Hz 60 Hz

12 VDC – – 27.9 mA

80% max.* 10% min.

–

Approx. 300 mW

110%

24 VDC – – 13.5 mA –

Approx. 300 mW

24 VAC/VDC 12.5 mA 12.6 mA 12.6 mA

Approx. 0.5 VA

Approx. 300 mW

48 VAC/VDC 5.9 mA 6.1 mA 5.2 mA

Approx. 0.4 VA

Approx. 250 mW

100 VAC 5.9 mA 6.0 mA –

Approx. 0.8 VA

–

110 VAC 5.9 mA 5.9 mA –

Approx. 0.8 VA

–

200 VAC 6.6 mA 7.6 mA –

Approx. 1.7 VA

–

230 VAC 7.3 mA 8.4 mA –

Approx. 1.7 VA

–

Item

Standard (G2RV-SR700, 500, 701, 501)

For microloads (G2RV-SR700-AP, 500-AP) *2

Contact configuration SPDT

Load Resistive load

(cosφ=1)

Inductive load

(cosφ=0.4, L/R=7ms)

Resistive load

(cosφ=1)

Rated load 6 A at 250 VAC

6 A at 30 VDC

2.5 A at 250 VAC

2 A at 30 VDC

50 mA at 30 VAC

50 mA at 36 VDC

Rated carry current 6 A 50 mA

Maximum switching voltage 440 VAC, 125 VDC 30 VAC, 36 VDC

Maximum switching current 6 A 50 mA

Maximum switching power 1,500 VA

180 W

500 VA

60 W –

Failure rate P value

(reference value) *1 10 mA at 5 VDC 1 mA at 100 mVDC

Item

Standard (G2RV-SR700, 500, 701, 501)

For microloads (G2RV-SR700-AP, 500-AP)

Contact resistance * 100 m Ω max.

Operate (Set) time * 20 ms max.

Release time * AC, AC/DC: 40 ms max.

DC: 20 ms max.

Maximum operating frequency Mechanical: 18,000 operations/h

Electrical: 1,800 operations/h (rated load)

Insulation resistance 1,000 MΩ min. (at 500 VDC)

Dielectric strength Between coil and contacts: 4,000VAC 50/60 Hz 1 min

Contact between the same polarity: 1,000 VAC 50/60 Hz 1 min

Vibration resistance Destruction: 10 to 55 to 10 Hz, single amplitude 0.50 mm (double amplitude 1.0 mm)

Malfunction: 10 to 55 to 10 Hz, single amplitude 0.50 mm (double amplitude 1.0 mm)

Shock resistance Destruction: 1,000 m/s2

Malfunction: Energized 200m/s2, Non-energized 100m/s2

Endurance *

Mechanical 5,000,000 operations min.

Electrical NO contact: 70,000 operations min.

NC contact: 50,000 operations min. 5,000,000 operations min.

Ambient operating temperature Operating: –40 to +55°C (with no icing or condensation)

Ambient operating humidity Operating: 5 to 85% RH

Weight Approx. 30 g

Contact material Ag alloy Ag alloy + Au plating

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Approved standards

UL508 (file No.E41643)

* If the load voltage exceeds 250 VAC, please attach with a spacing

of 12 mm min., or use a separate plate (XW5Z-EP12).

\TÜV (EN 61810-1)

* If the load voltage exceeds 250 VAC, please attach with a spacing

of 12 mm min., or use a separate plate (XW5Z-EP12).

Lloyd's (File No.07/10020)

Engineering Data

Endurance curve (N.O. side) Switching capacity of DC resistive load

Model Contact form Operation coil ratings Contact ratings Operations

G2RV-SR series

SPDT 12 to 48 VDC

24 to 230 VAC

6 A at 250 VAC (Resistive load)

6 A at 30 VDC (Resistive load)

2 A at 400 VAC (Resistive load)*

6,000

12 mm 12 mm 12 mm

Model Contact form Operation coil ratings Contact ratings Operations

G2RV-SR series

SPDT

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

6 A at 250 VAC (Resistive load)

6 A at 30 VDC (Resistive load)

2 A at 400 VAC (Resistive load)*

50,000

6,000

12 mm 12 mm 12 mm

Model Contact form Operation coil ratings Contact ratings

G2RV-SR500

G2RV-SR700 SPDT

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

6 A at 250 VAC (Resistive load)

2.5 A at 250 VAC (PF0.4)

6 A at 30 VAC (Ress)

2 A at 30 VDC (L/R=7ms)

G2RV-SR501

G2RV-SR701 SPDT 12, 24 VDC

24 VAC/VDC

6 A at 250 VAC (Resistive load)

2.5 A at 250 VAC (PF0.4)

6 A at 30 VAC (Ress)

2 A at 30 VDC (L/R=7ms)

G2RV-SR500-AP

G2RV-SR700-AP SPDT

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

0.05 A at 30 VAC (Resistive load)

0.05 A at 36 VDC (Resistive load)

100

1000

024

Opening and closing current (A)

250 VAC resistive load

30 VDC resistive load

30 VDC

inductive load

250 VAC

inductive

load

Number of operations (x 103 operations)

0.1

1.0

10.0

20 60 100 140 180 220

DC switching voltage (V)

DC breaking current (A)

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Dimensions (unit: mm)

Slim I/O Relay + socket

Push-In Plus Terminal Block

74.1

51.72

35.25

18.78

35.25

74.5

18.78

35.3

78.77

(5.05)

59.71

3.4

78 max.

90 max.

6.2 max.

Input circuit

G2RV

12 VDC

Input circuit

G2RV

: Diode bridge

Other voltage

: Light emitting diode

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

24 VDC

(+)

(–)

(+)

(–)

Models without latching lever (without test switch)

G2RV-SR500

G2RV-SR500-AP

74.1

51.72

35.25

18.78

35.25

77.5

18.78

35.3

78.77

(5.05)

59.71

3.4

81 max.

90 max.

6.2 max.

(+)

(–)

G2RV

(+)

(–)

Input circuit

: Diode bridge

Other voltage

: Light emitting diode

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

24 VDC

Models with latching lever (with test switch)

G2RV-SR501

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Screw terminal

74.1

51.65

35.18

18.71

35.18

74.5

(5.05)

35.3

78.77

56.2

3.4

78 max.

6.2 max.

90 max.

(+)

(–) 11

Input circuit

G2RV

Input circuit

G2RV

: Diode bridge

Other voltage

: Light emitting diode

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

Input circuit

G2RV

24 VDC

(+)

(–)

Models without latching lever (without test switch)

G2RV-SR700

G2RV-SR700-AP

74.1

51.65

35.18

18.71

35.18

77.5

(5.05)

35.3

78.77

56.2

3.4

81 max.

6.2 max.

90 max.

(+)

(–)

(+)

(–)

G2RV

Input circuit

: Diode bridge

Other voltage

: Light emitting diode

Terminal Arrangement/Internal Connection Diagram

(TOP VIEW)

12 VDC

24 VDC

Models with latching lever (with test switch)

G2RV-SR701

G2RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Relay for maintenance

30.5 max.

3.5

0.5 2.4

1.8

5.2 max.

5.04 5.04

33 max.

16.2

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

(Input circuit)

Models without latching lever

G2RV-1-S-G

G2RV-1-S-AP-G

Models with latching lever (test switch)

G2RV-1-SI-G

30.5 max.

5.2 max.

1.8 0.5

2.4

5.04

36 max.

16.2

3.5

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

(Input circuit)

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Slim I/O Solid State Relay

G3RV-SR

Global standard size, low profile type

slim I/O solid state relay with width

6.2 mm.

• Realized about 25% lower profile than conventional products,

contributing to further miniaturization of the control panel.

• Optimal slim, high frequency, high-speed opening and closing

SSR (solid state relay).

• Realized a slim shape with a switching capacity up to

3A(DC), and 2A(AC).

• Because MOSFET is used for the outlet element for the DC

load, opening and closing load of 100 μA to 3 A is possible.

• Check operating status at a glance at the operating display

LED.

• Mounted I/O SSR (solid-state relay) uses plug-in terminals that

are difficult to bend when exchanging.

• G2RV-SR featuring a general-purpose relay similar in shape to G3RV-SR also available.

Features

For the recent information on models that have been certified

for safety standards, refer to your OMRON website.

Refer to Safety Precautions on page 20.

Terminal x 5

• Push-in

• Screw

Release lever

Operation display LED

(Socket section)

Operation

display LED

(SSR section)

Push-In Plus technology

Short bar insertion holes

Terminal (insertion) hole

Release hole

Release lever

Plug-in terminal

90 mm

80 mm

Relay easily

fixed/removed

Peace of mind as the terminal

does not bend when replacing

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

G3RV-SR

Model Number Structure

Model Number Legend

(1) Basic model name

G3RV: Slim I/O Solid State Relay

(2) Sub type

SR: Slim solid relay + integrated low profile socket

(3) Terminal (wire connection)

500: Push-In Plus Terminal

700: Screw terminal

(4) Output voltage specification

A : AC output (triac) zero cross function available

AL : AC output (triac) zero cross function not available

D : DC output (MOS FET)

(5) Rated voltage input

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

G3RV-SR @ @ @ - @ @

(1) (2) (3) (4) (5)

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Ordering Information

Note: Sockets are not sold individually.

Terminal

(wire connection) Applicable

output load Zero cross

function Rated input voltage

(V) Model

Push-In Plus Terminal

DC load —

DC 12 G3RV-SR500-D DC12

24 G3RV-SR500-D DC24

AC/DC 24 G3RV-SR500-D AC/DC24

48 G3RV-SR500-D AC/DC48

100 G3RV-SR500-D AC100

110 G3RV-SR500-D AC110

200 G3RV-SR500-D AC200

230 G3RV-SR500-D AC230

AC load

Yes

DC 12 G3RV-SR500-A DC12

24 G3RV-SR500-A DC24

AC/DC 24 G3RV-SR500-A AC/DC24

48 G3RV-SR500-A AC/DC48

100 G3RV-SR500-A AC100

110 G3RV-SR500-A AC110

200 G3RV-SR500-A AC200

230 G3RV-SR500-A AC230

DC 12 G3RV-SR500-AL DC12

24 G3RV-SR500-AL DC24

AC/DC 24 G3RV-SR500-AL AC/DC24

48 G3RV-SR500-AL AC/DC48

100 G3RV-SR500-AL AC100

110 G3RV-SR500-AL AC110

200 G3RV-SR500-AL AC200

230 G3RV-SR500-AL AC230

Screw terminal

DC load —

DC 12 G3RV-SR700-D DC12

24 G3RV-SR700-D DC24

AC/DC 24 G3RV-SR700-D AC/DC24

48 G3RV-SR700-D AC/DC48

100 G3RV-SR700-D AC100

110 G3RV-SR700-D AC110

200 G3RV-SR700-D AC200

230 G3RV-SR700-D AC230

AC load

Yes

DC 12 G3RV-SR700-A DC12

24 G3RV-SR700-A DC24

AC/DC 24 G3RV-SR700-A AC/DC24

48 G3RV-SR700-A AC/DC48

100 G3RV-SR700-A AC100

110 G3RV-SR700-A AC110

200 G3RV-SR700-A AC200

230 G3RV-SR700-A AC230

DC 12 G3RV-SR700-AL DC12

24 G3RV-SR700-AL DC24

AC/DC 24 G3RV-SR700-AL AC/DC24

48 G3RV-SR700-AL AC/DC48

100 G3RV-SR700-AL AC100

110 G3RV-SR700-AL AC110

200 G3RV-SR700-AL AC200

230 G3RV-SR700-AL AC230

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Solid state relay for maintenance

Model Number Legend

List of Models

*Different depending on the ambient temperature.

For more details, refer to Load current vs. ambient rated temperature on page 16.

Accessories (order separately)

Refer to page 25 for G2RV-SR/G3VR-SR Common Accessories.

(1) Output voltage

specification

D: DC output

2: AC output

(2) Rated current

02: AC output 2 A

03: DC output 3 A

(3) Terminal

S: Plug-in type

(4) Zero cross functions

Blank: Zero cross function available

L: Zero cross function not available

(5) Rated input voltage

Number: 12, 24, 48 VDC

G3RV-@ @ S @

(1) (2) (3) (4) (5)

Insulation

method

Operation

Display

Output

(SSR)

Zero cross

Function

Rated

output

Load *

Rated input

voltage

(socket) Model Applicable model

Photo-

triac

Yes

(green)

Yes

2 A

(at 100 to

240

VAC)

12 VDC G3RV-202S DC12 G3RV-SR700/500-A DC12V

24 VDC G3RV-202S DC24 G3RV-SR700/500-A DC24V

24 VAC/VDC G3RV-SR700/500-A AC/DC24V

48 VAC/VDC

G3RV-202S DC48

G3RV-SR700/500-A AC/DC48V

100 VAC G3RV-SR700/500-A AC100V

110 VAC G3RV-SR700/500-A AC110V

200 VAC G3RV-SR700/500-A AC200V

230 VAC G3RV-SR700/500-A AC230V

12 VDC G3RV-202SL DC12 G3RV-SR700/500-AL DC12V

24 VDC G3RV-202SL DC24 G3RV-SR700/500-AL DC24V

24 VAC/VDC G3RV-SR700/500-AL AC/DC24V

48 VAC/VDC

G3RV-202SL DC48

G3RV-SR700/500-AL AC/DC48V

100 VAC G3RV-SR700/500-AL AC100V

110 VAC G3RV-SR700/500-AL AC110V

200 VAC G3RV-SR700/500-AL AC200V

230 VAC G3RV-SR700/500-AL AC230V

Photo-

voltage

coupler

DC –

3 A

(at 5 to

24 VDC)

12 VDC G3RV-D03SL DC12 G3RV-SR700/500-D DC12V

24 VDC G3RV-D03SL DC24 G3RV-SR700/500-D DC24V

24 VAC/VDC G3RV-SR700/500-D AC/DC24V

48 VAC/VDC

G3RV-D03SL DC48

G3RV-SR700/500-D AC/DC48V

100 VAC G3RV-SR700/500-D AC100V

110 VAC G3RV-SR700/500-D AC110V

200 VAC G3RV-SR700/500-D AC200V

230 VAC G3RV-SR700/500-D AC230V

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Specifications

Rating (ambient temperature 25°C)

Input

G3RV-SR700/500-A series

G3RV-SR700/500-AL series

G3RV-SR700/500-D series

Output

Rated input

voltage

Rated current Must operate

voltage Must release

voltage

Input voltage

AC DC Percentage of the

rated voltage

50 Hz 60 Hz

12 VDC – – 15.0 mA 10.8 V max.

1 V min. ±10%

24 VDC – – 12.0 mA 21.6 V max.

24 VAC/VDC 11.3 mA 11.4 mA 11.0 mA 21.6 V max.

48 VAC/VDC 6.8 mA 6.9 mA 6.0 mA 43.2 V max.

100 VAC 6.2 mA 6.2 mA – 90 V max.

110 VAC 6.2 mA 6.2 mA – 99 V max.

200 VAC 6.7 mA 7.9 mA – 180 V max.

230 VAC 7.5 mA 8.8 mA – 207 V max.

Rated input

voltage

Rated current Must operate

voltage Must release

voltage

Input voltage

AC DC Percentage of the

rated voltage

50 Hz 60 Hz

12 VDC – – 15.0 mA 10.8 V max.

1 V min. ±10%

24 VDC – – 12.0 mA 21.6 V max.

24 VAC/VDC 11.4 mA 11.5 mA 11.0 mA 21.6 V max.

48 VAC/VDC 7.7 mA 7.7 mA 6.9 mA 43.2 V max.

100 VAC 7.3 mA 7.3 mA – 90 V max.

110 VAC 7.3 mA 7.3 mA – 99 V max.

200 VAC 7.0 mA 8.1 mA – 180 V max.

230 VAC 7.7 mA 8.9 mA – 207 V max.

Rated input

voltage

Rated current Must operate

voltage Must release

voltage

Input voltage

AC DC Percentage of the

rated voltage

50 Hz 60 Hz

12 VDC – – 8.0 mA 10.8 V max.

1 V min. ±10%

24 VDC – – 4.6 mA 21.6 V max.

24 VAC/VDC 5.0 mA 5.1 mA 4.3 mA 21.6 V max.

48 VAC/VDC 6.8 mA 6.9 mA 6.0 mA 43.2 V max.

100 VAC 6.2 mA 6.2 mA – 90 V max.

110 VAC 6.2 mA 6.2 mA – 99 V max.

200 VAC 6.7 mA 7.9 mA – 180 V max.

230 VAC 7.5 mA 8.8 mA – 207 V max.

Item G3RV-SR700/500-A(L) G3RV-SR700/500-D

Rated load voltage 100 to 240 VAC (50/60 Hz) 5 to 24 VDC

Load voltage range 75 to 264 VAC (50/60 Hz) 3 to 26.4 VDC

Load current

0.1 to 2 A (Ambient temperature=25°C)

100

A to 3 A (Ambient temperature=25°C)

Inrush current resistance 30 A (60 Hz, 1 cycle) 30 A (60 Hz, 1 cycle)

Permissible l

t; Joule integral value

(reference value)

15A2s9 A

2 s

Applied load capacity 400 W

(Output voltage: 200 VAC)

72 W

(Output voltage: 24 VDC)

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Characteristics

Approved standards

UL 508 (file No.E64562)

TÜV(EN 62314)

Item G3RV-SR700/500-A G3RV-SR700/500-AL G3RV-SR700/500-D

Operate time 1/2 cycle of load power supply

+1 ms max. 3 ms max. 6 ms max.

Release time 60 ms max. 60 ms max. 60 ms max.

Output ON voltage drop 1.6 V (RMS) max. –

Output ON resistance –0.3 Ω max. (at 24 VDC)

Leaked current 5 mA max. (at 200 VAC, 50/60 Hz) 10 µA max. (at 24 VDC)

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength Between input and output 2,500 VAC 50/60 Hz 1 min

Vibration resistance Malfunction: 10 to 55 to 10 Hz double amplitude 0.70 mm

Shock resistance 300m/s2

Ambient operating temperature Storage: –30 to +100°C (with no icing or no condensation)

Operating: –30 to +55°C (with no icing or no condensation)

Ambient operating humidity 45 to 85% RH

Weight Approx. 38 g

Pollution degree 2

The degree of protection by

IEC60529 IP20

Rated impulse dielectric

strength 4.0 kV/III

Load category LC-A DC-12

Overload current profile 1.5Ie 1.1Ue

5s ON, 10s OFF, 10 cycles

Rated insulation voltage 240 V

Model Input ratings Contact ratings

G3RV-SR700/500-D series

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

24 VDC 3 A (resistive load) at 25°C

G3RV-SR700/500-A(L) series

12, 24 VDC

24, 48 VAC/DC

100, 110, 200, 230 VAC

240 VAC 2 A (resistive load) at 25°C

Model Input ratings Contact ratings

G3RV-SR700/500-D series

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

24 VDC 3 A (resistive load)

G3RV-SR700/500-A(L) series

12, 24 VDC

24, 48 VAC/VDC

100, 110, 200, 230 VAC

240 VAC 2 A (resistive load)

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Engineering Data

Load current vs. ambient rated temperature

G3RV-SR700/500-A(L) series

G3RV-SR700/500-D series

Inrush Current Resistance: Non-repetitive

Keep the inrush current to below the inrush current resistance value (i.e., below the broken line) if it occurs repetitively.

Product mounting spacing 10 mm (Separate Mounting) Close mounting (up to 5 units *)

*When five or more are installed, install with 10 mm space between

each.

For details, please refer to Mounting on page 23.

G3RV-SR700/500-A(L) series G3RV-SR700/500-D series

−30 −20 0 40 60 80 10055

Ambient temperature (°C)

Load current (A)

20 25 −30 −20

0.2

0 40 60 80 10055

020 25

Ambient temperature (°C)

Load current (A)

−30 −20 0 40 60 80 10055

020 25

Ambient temperature (°C)

Load current (A)

−30 −20

0.5

0 20 25 40 60 80 10055

Ambient temperature (°C)

Load current (A)

Inrush current (A.Peak)

10 30 50

100 300 500 1,000 3,000 5,000

Energized time (ms)

10 30 50

100 300 500 1,000 3,000 5,000

Inrush current (A.Peak)

Energized time (ms)

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

G3RV-SR

Dimensions (unit: mm)

Solid state relay + socket

Push-In Plus Terminal Block

G3RV-SR500

Input circuit

: Diode bridge

: Light emitting diode

Input circuit

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

The information in

parentheses in for

a DC output.

The information in

parentheses in for

a DC output.

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

The information in

parentheses in for

a DC output.

(+)

(–)

(+)

(–)

74.1

51.72

35.25

18.78

35.25

74.5

18.78

35.3

78.77

(5.05)

59.71

3.4

78 max.

90 max.

6.2 max.

12 VDC

24 VDC

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

Other voltage

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Screw terminal

G3RV-SR700

Input circuit

: Diode bridge

Input circuit

: Light emitting diode

Input circuit

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

The information in

parentheses in for

a DC output.

The information in

parentheses in for

a DC output.

A2–

A1+

13 (+)

14 (–)

G3RV

INPUT

OUTPUT

The information in

parentheses in for

a DC output.

(+)

(–)

(+)

(–)

12 VDC

24 VDC

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

74.1

51.65

35.18

18.71

35.18

74.5

(5.05)

35.3

78.77

56.2

3.4

78 max.

6.2 max.

90 max.

Other voltage

G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Solid state relay for maintenance

G3RV-D03SL

G3RV-202S(L)

Terminal Arrangement/

Internal Connection Diagram

(TOP VIEW)

G3RV-D03SL (input circuit)

G3RV-202S(L) (input circuit)

33 max.

30.5 max.

2.4

15.8

5.2 max.

3.5

1.8

5.04 3

14 13 A1 A2

Input

Load

14 13 A1 A2

Input

Load

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Safety Precautions

Be sure to read the Safety Precautions for All Relays in the website at the following URL:

http://www.ia.omron.com/.

Format of Warning Indications

Meaning of Graphic Symbols for Ensuring Product Safety

Ensure that the socket is not charged during wiring and

maintenance. Not doing so may result in electric shock.

Do not touch the terminal section of the G2RV-SR or the

surrounding area while the power is being supplied.

Doing so may result in electric shock.

Minor electrical shock may occasionally occur.

Do not touch the G3RV terminal section (i.e., current

carrying parts) while the power is being supplied.

The G3RV may rupture if short-circuit current flows.

As protection against accidents due to short-circuiting,

be sure to install protective devices, such as fuses and

no-fuse breakers, on the power supply side.

Minor electrical shock may occasionally occur.

Do not touch the main circuit terminals on the G3RV

immediately after the power supply has been turned

OFF.

Shock may result due to the electrical charge stored

in the built-in snubber circuit.

Note: G3RV-202S(L), G3RV-SR500/700-A(L) series

models only

Minor burns may occasionally occur.

Do not touch the G3RV or the heat sink while the

power is being supplied or immediately after the

power supply has been turned OFF.

The G3RV becomes extremely hot.

Provide a space of at least 3 mm between the G2RV-

SR and ground. Not doing so may result in a ground

fault.

WARNING

Indicates a potentially hazardous situation

which, if not avoided, will result in minor or

moderate injury, or may result in serious

injury or death. Additionally, there may be

significant property damage.

CAUTION

Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury or in property damage.

Precautions

for Safe Use

Indicates supplementary comments on

what to do or avoid doing, to use the

product safety.

Precautions

for Correct

Use

Includes operating precautions to ensure

that the product will operate properly and

that performance and functions will not be

adversely affected.

Indicates the possibility of electric shock under

specific conditions.

Used for general CAUTION, WARNING, or

DANGER precautions for which there is no

specified symbol. (This symbol is also used as

the alerting symbol, but shall not be used in this

meaning on the product.)

Indicates the possibility of explosion or rupture

under specific conditions.

Indicates the possibility of injuries by high

temperature under specific conditions.

WARNING

CAUTION

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Transport

• Do not use the product if it has been dropped on the ground.

Dropping the product may adversely affect performance.

• Do not drop the product or subject it to abnormal vibration or shock

during transportation or mounting. Doing so may result in

deterioration of performance, malfunction, or failure.

• Do not transport the product without it being packaged. Doing so

may result in damage, malfunction, or failure.

• Do not transport the G3RV under the following conditions. Doing

so may result in damage, malfunction, or deterioration of

performance characteristics.

• High temperature, high humidity conditions

• Conditions such as temperature change that causes rapid

condensation

• Condition where it is not packaged

Operating and Storage Environments

• Do not use or store the product in the following locations. Doing so

may result in damage, malfunction, or deterioration of performance

characteristics.

• Do not store in locations subject to ambient storage

temperatures outside the range –40 to 70°C (for G2RV) and

outside the range –30 to 100°C (for G3RV).

• Locations subject to relative humidity outside the range 5% to

85% (for G2RV) and outside the range 45% to 85% (for G3RV).

• Locations subject to high temperature or high humidity.

• Conditions such as temperature change that causes rapid

condensation

•L

ocations where corrosive gases or flammable gases are present

• Location where rainwater or water droplets gets splashed

• Location with splashes of water, oil, and chemicals, etc.

• Locations with much dust, salt, and iron powder

• Location with blockers

• Where static electricity or noise occurs

• Where strong electromagnetic field is generated

• Where there is a risk of exposure to radioactivity

• Do not use or store Sockets in environments that contain silicone

gas, sulfidizing gas (e.g., SO2 or H2S), or organic gas, or near

materials that contain silicone. Doing so may cause the contacts to

be unstable or to fail.

Handling <G3RV>

• Keep the G3RV well ventilated.

There is a risk of short-circuiting or burning due to G3RV

overheating.

Mounting

• Before you start wiring, please make sure that the socket is

securely attached to the mounting rail. If the socket is unstable, it

may come loose and risk of injury towards the workers.

•

Please insert the flat-blade screwdriver to the bottom of the hole. If

you do not insert the flat-blade screwdriver correctly, the cable will

not be connected correctly

• When lubricant such as oil is attached to the tip of the driver, the

driver will fall off, with a risk of injury towards the workers.

• Do not tilt the G2RV-SR/G3RV-SR after mounting to the support

rail. Doing so may apply excessive force to the mounting portion,

possibly damaging the product. Attach end plates (PFP-M) to

sandwich the product and hold it in place.

Usage

• Please select the load within the rated range. Doing so may result

in damage, malfunction, or failure.

• Please use the power of the rated frequency. It may cause

malfunction, failure, or risk of burnout.

<G3RV>

• Install G3RV according to instructions Mounting on page 23. If you

install in the wrong direction, abnormal heat is generated, and may

lead to short-circuiting or burning the output element.

• G3RV is an SSR that generates heat. Please observe the ambient

temperature setting range of G3RV. If installing in an enclosed

space, set a fan, and ventilate.

• When mounting G3RV to DIN rail, firmly fits into the groove. If it is

not properly installed, there is a risk of it falling.

Wiring

•

For the current to be applied, make sure a wire size with margin is used.

Otherwise, excessive heat generated by the wires may cause burning

• Do not attempt to use the wire if the coat is torn. Not doing so may

result in electric shock.

• Always turn OFF the power supply before performing wiring. Not

doing so may cause electrical shock.

<G3RV>

• The wires of the socket for G3RV socket should not be passed

through the same duct as that being connected to the high-voltage

power supply. Otherwise, inductive noise may damage the G3RV

or cause it to malfunction.

Push-In Plus Terminal Block

• Do not wire anything to the release holes.

•

Do not tilt or twist a flat-blade screwdriver while it is inserted into a release

hole on the terminal block. The terminal block may be damaged

• Insert a flat-blade screwdriver into the release holes at an angle.

The terminal block may be damaged if you insert the screwdriver

straight in.

• Do not allow the flat-blade screwdriver to fall out while it is inserted

into a release hole.

• Do not bend the wire past its natural bending radius or pull on it

with excessive force. Doing so may cause the wire disconnection.

•

Do not insert more than one wire into each terminal (insertion) hole

• To prevent wiring materials from smoking or ignition, confirm wire

ratings and use the wiring materials given in the following table.

Disposal

• When disposing of the product, do not put into the fire.

Precautions for Safe Use

Recommended Wire Stripping length

(Ferrules not used)

0.5 to 1.5 mm2/AWG20 to AWG16 8 mm

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

• Do not use or store the product in the following locations. Doing so

may result in damage, malfunction, or deterioration of performance

characteristics.

• Where vibration or shock is directly transmitted to the body

• Where the socket could come into contact with a solvent or

alkaline agent

• Insert the short bar into the insertion hole in the correct orientation,

and insert until all terminals are all the way in.

• If using a short bar, install the short bar before performing wiring

work.

• A push-in Plus terminal block type and a screw terminal type have

different insertion positions, so a mixed installation using the same

short bar is not possible.

• Do not insert short bar in the hole for wire or screw driver, it may

cause the result of failure of pull out.

If insert short bar in the hole for wire or screw driver and try to pull

out, it may cause damage for short bar or socket and failure in

electric conductivity.

• Please insert P2RVC terminal into the short bar insertion hole of

G2RV-SR/G3RV-SR. If insert P2RVC into the release hole or

terminal (insertion) hole wrongly, P2RVC may stuck and can not

remove and it may cause result of damage on P2RVC and G2RV-

SR/G3RV-SR.

Please turn off the power of input and output side and remove PLC

interface unit when replacing mounting relays and SSRs for

maintenance.

• When replacing relays, there is a possibility the relay will pop out

and fall. Take care to prevent the relay from falling during

replacement.

Push-In Plus Terminal Block

1. Connecting Wires to the Push-In Plus Terminal Block

Part Names of the Terminal Block

Connecting Wires with Ferrules and Solid Wires

Insert the solid wire or ferrule straight into the terminal block until the

end strikes the terminal block.

• If a wire is difficult to connect because it is too thin, use a flat-blade

screwdriver in the same way as when connecting stranded wire.

Connecting Stranded Wires

Use the following procedure to connect the wires to the terminal block.

(1) Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

The angle should be between 10°and15°. If the flat-blade

screwdriver is inserted correctly, you will feel the spring in the

release hole.

(2) With the flat-blade screwdriver still inserted into the release hole,

insert the wire into the terminal hole until it strikes the terminal

block.

(3) Remove the flat-blade screwdriver from the release hole.

Checking Connections

• After the insertion, pull gently on the wire to make sure that it will

not come off and the wire is securely fastened to the terminal block.

• If you use a ferrule with a conductor length of 10 mm, part of the

conductor may be visible after the ferrule is inserted into the

terminal block, but the product insulation distance will still be

satisfied.

2. Removing Wires from the Push-In Plus Terminal Block

Use the following procedure to remove wires from the terminal block.

The same method is used to remove stranded wires, solid wires, and

ferrules.

(1) Hold a flat-blade screwdriver at an angle and insert it into the

release hole.

(2) With the flat-blade screwdriver still inserted into the release hole,

remove the wire from the terminal insertion hole.

(3) Remove the flat-blade screwdriver from the release hole.

Precautions for Correct Use

Orient correctly

and push all the

way in.

Completely inserted

All terminals are inserted all the way in.

Incomplete insertion

All terminals are not inserted

all the way in.

Incomplete

insertion

Incorrect installation

Some terminals not inserted

completely.

Release hole

Terminal (Insertion) hole

Release hole

Terminal

(Insertion) hole

Ferrules or

solid wire

(2)

Flat-blade screwdriver

Stranded Wires

10 to 15°

(1) (3)

(2)

(1)

(3)

(2)

10 to 15°

Wire

Flat-blade screwdriver

(1) (3)

(2)

(1)

(3)

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

3. Recommended ferrules and Crimp Tools

Recommended ferrules

Note: 1. Make sure that the outer diameter of the wire is smaller than

the inner diameter of the insulating sleeve of the

recommended ferrule.

2. Make sure that the ferrule processing dimensions conform

to the following figure.

3. If you use AWG24 to AWG22 (0.25 to 0.34 mm2) wires, UL

certification will not apply.

Recommended Flat-blade Screwdriver

Use a flat-blade screwdriver to connect and remove wires.

Use the following flat-blade screwdriver.

The following table shows manufacturers and models as of 2015/Dec.

*OMRON's exclusive purchase model XW4Z-00B is available to

order as SZF 0-0,4×2,5 (manufactured by Phoenix Contact).

Screw Terminal

• Screw terminal

• Tightening Torque

0.4 N • m

• Electric wiring

Use the electric wire of specified size as shown above. The length

of the that is not covered is 8 mm.

<G2RV>

Operating latching lever (test switch)

When operating the latching lever for G2RV-SR701/501

series, use a 2.5 mm width flat-blade screwdriver.

• Applicable flat-blade screwdriver

Flat-blade screwdriver with parallel cutting edge: shaft diameter

2.5 mm (3.0 mm max.)

• Always turn OFF the power supply before operating latching lever.

• Return to its original state after using the latching lever.

• Do not use the latching lever as a switch.

• Operation durability of the latching lever is 100 times or more.

• Do not keep the latching lever ON for a long period of time (24

hours or more) in order to maintain the operation check function.

Applicable

wire

Ferrules

Conduct

length

(mm)

Stripping

length

(mm)

(Ferrules

used)

Recommended ferrules

(mm2)

(AWG)

Phoenix Contact

product

Weidmuller

product

Wago

product

0.25 24 8 10 AI 0,25-8 H0.25/12 216-301

10 12 AI 0,25-10 --- ---

0.34 22 8 10 AI 0,34-8 H0.34/12 216-302

10 12 AI 0,34-10 --- ---

0.5 20 8 10 AI 0,5-8 H0.5/14 216-201

10 12 AI 0,5-10 H0.5/16 216-241

0.75 18 8 10 AI 0,75-8 H0.75/14 216-202

10 12 AI 0,75-10 H0.75/16 216-242

1/1.25 18/17 8 10 AI 1-8 H1.0/14 216-203

10 12 AI 1-10 H1.0/16 216-243

1.25/1.5

17/16 8 10 AI 1,5-8 H1.5/14 216-204

10 12 AI 1,5-10 H1.5/16 216-244

Recommended crimp tool

CRIMPFOX6

CRIMPFOX6T-F

CRIMPFOX10S

PZ6 roto

Variocrimp4

Model Manufacturer

ESD 0,40×2,5 Wera

SZS 0,4×2,5

SZF 0-0,4×2,5 *Phoenix Contact

0.4×2.5×75 302 Wiha

AEF.2,5×75 Facom

210-719 Wago

SDI 0.4×2.5×75 Weidmuller

8 to 10 mm

1.9 mm max. 2.6 mm max.

Side

0.4 mm

2.5 mm dia.

2.5 mm

Front

Wired type Applicable wire

size Stripping

length

Stranded wires, without

ferrule 0.5 to 1.5 mm28 mm

Stranded wires, with ferrule

and plastic collar 0.5 to 1.5 mm28 mm

Stranded wires with ferrule,

without plastic collar 0.5 to 1.5 mm28 mm

Single wire 0.5 to 1.5 mm28 mm

Stripping length

8 mm

Screw terminal

Shaft diameter 2.5 mm (3.0 mm max.)

Driver with a thick shaft cannot be used.

Wide flat-blade screwdriver

Parallel cutting edge flat-blade screwdriver

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Method of operation of the latching lever (test

switch)

Keep the protective cover open when using the latching lever. Move

until the latching lever clicks to the ON position (ON state). After use

latching lever, in order to prevent malfunction, return the switch to

contact normal position (OFF state), and make sure the protective

cover is firmly closed.

Using the latching lever

Example: check the operation of the relay and the sequence circuit

Input ratings

Smoothing capacitors are used in the internal circuits of AC/DC-

type G2RV-SR devices. AC/DC-type G2RV-SR devices driven by

the sensor may not operate normally due to the characteristics of

the smoothing capacitor. When driving such devices by the

sensor, use the DC specification settings.

<G3RV>

• Since the G3RV uses electronic components, do not allow it to fall,

vibrate, or apply shock that exceeds the criteria. Doing so may

result in failure, malfunction, or deterioration of performance.

• Tighten screw terminal for G3RV at torque 0.4 N · m. It may cause

short-circuit failure or burning.

• Please use the voltage and current suitable for the input and

output terminal portion of G3RV. It may cause short-circuit failure

or burning.

Mounting

*When five or more are installed, install with 10 mm space between

each.

• If the air inlet or air outlet has a filter, clean the filter regularly to

prevent it from clogging to ensure an efficient flow of air.

• Do not place objects that may obstruct the proper ventilation for

outside or inside the inlet or exhaust port, and in the outside

vicinity.

• A heat exchanger, if used, should be located in front of the G3RV

to ensure the efficiency of the heat exchanger.

• Please observe the ambient temperature of G3RV. The rated

current of the G3RV is measured at an ambient temperature of

25°C.

• The G3RV uses a semiconductor in the output element.

This causes the temperature inside the control panel to increase

due to heating resulting from the flow of electrical current through

the load. The G3RV reliability can be increased by adding a

ventilation fan to the control panel to dispel this heat, thus lowering

the ambient temperature of the G3RV.

(It suggests that life expectancy is doubled by each 10°C reduction

in ambient temperature.)

EMI

The G3RV is a Class A product (for industrial environments). When

used in a residential environment, it may cause radio interference.

In such case, the user may be required to take appropriate

measures.

Contact normal position

Contact operating position (on-state)

Close protective cover Open protective cover

SSR 10 mm min.

30 mm min.

80 mm min.

60 mm min.

Duct or other object blocking airflow

Vertical Direction

Airflow

Metal

base

SSR SSR

Incorrect Example Countermeasure 1 Countermeasure 2

Mounting surface

SSR

Duct or other object

blocking airflow

Recommended height of the duct is

1/2 or less of the height of the SSR

Duct or other object

blocking airflow

Vertical

Direction

Duct or other object

blocking airflow

Duct or other object

blocking airflow

Duct or other object

blocking airflow

Duct or

other object

blocking

airflow

Do not enclose the SSR in a

duct of the same height.

It will interfere with the heat

dissipation of SSR.

Use ducts that have a

shallow depth, to provide a

sufficient ventilation area.

If the ducts cannot be made lower,

place the SSR on a metal base so

that it is not surrounded by the ducts.

Height of SSR

SSR

Inlet

Be aware of airflow

Exhaust

(Axial fan)

SSR

Duct or other object

blocking airflow

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Ordering Information

Short Bars

Note: Use for wiring to the adjacent socket.

*Replace the box (@) in the model number with the code for the covering color. @ color selection: R = red, S = blue, Y = yellow

Label

*Available following June 2017 production.

Separate Plate

PLC interface unit

*Please make sure applicable models, P2RVC can not be used other combination than the above table.

Parts for DIN Track Mounting

*When mounting DIN Track, please use End Plate (PFP-M).

Refer to your OMRON website for details on PFP-@.

For G2RV-SR/G3VR-SR

Common Accessories (order separately)

Appearance Pitch No. of

poles Colors Model * Minimum order

(Quantity)

Maximum energizing

current

6.2 mm

Red (R),

Blue (S),

Yellow (Y)

PYDN-6.2-020@

10 32 A

3PYDN-6.2-030@

4PYDN-6.2-040@

10 PYDN-6.2-100@

20 PYDN-6.2-200@

Appearance Model Minimum order (Sheet)

(Pieces per sheet)

XW5Z-P2.5LB1 *

(1 sheet/72 pieces)

XW5Z-P2.5LB2

Appearance Model

XW5Z-EP12

Appearance I/O classification Connection method Common process Applicable Models *Model

For input

Push-In

PNP

G2RV-SR500-AP

P2RVC-8-I-5-1

NPN P2RVC-8-I-5

Screw PNP G2RV-SR700-AP P2RVC-8-I-7-1

For output

Push-In

PNP G2RV-SR500

G2RV-SR501

G3RV-SR500

P2RVC-8-O-5-1

NPN P2RVC-8-O-5

Screw PNP

G2RV-SR700

G2RV-SR701

G3RV-SR700

P2RVC-8-O-7-1

Appearance Type Model Minimum order

(Quantity)

DIN Tracks

1 m PFP-100N

0.5 m PFP-50N

End Plate *PFP-M

Spacer PFP-S

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Applicable Cables

Name Appearance Cable

length L

(mm) Connecting Cables Applicable Connectors

Cables with Loose

Wires

P2RV-A@C

8 I/O

points

1,000 P2RV-A100C

Various devices

2,000 P2RV-A200C

3,000 P2RV-A300C

5,000 P2RV-A500C

Cables with

Connectors (1:4)

P2RV-4-@C

32 output

points

1,000 P2RV-4-100C

PLC I/O Units with MIL connectors (1:4)

CJ1W-OD232/OD262, etc.

2,000 P2RV-4-200C

3,000 P2RV-4-300C

5,000 P2RV-4-500C

Cables with

Connectors (1:4)

P2RV-4-@IMC

32 input

points

1,000 P2RV-4-100IMC

PLC I/O Units with MIL connectors (1:4)

CJ1W-ID232/ID262, etc.

2,000 P2RV-4-200IMC

3,000 P2RV-4-300IMC

5,000 P2RV-4-500IMC

Cables with

Connectors (1:4)

P2RV-4-@IFC

32 input

points

1,000 P2RV-4-100IFC

PLC I/O Units with Fujitsu connectors (1:4)

CJ1W-ID231/ID261, etc.

2,000 P2RV-4-200IFC

3,000 P2RV-4-300IFC

5,000 P2RV-4-500IFC

Cables with Connectors

(1:1)

P2RV-A

C-OMR GRT1

8 output

points

500

P2RV-A050C-OMR GRT1

Slice I/O Units (1:1)

For inputs: GRT1-ID8-1

For outputs: GRT1-OD8-1

1,000

P2RV-A100C-OMR GRT1

8 input

points

500

P2RV-A050IC-OMR GRT1

1,000

P2RV-A100IC-OMR GRT1

Cables with

Connectors (1:1)

P2RV-A@C-OMR NX

8 output

points

500 P2RV-A050C-OMR NX

PLC I/O Units with screw-less clamp

terminal block (1:1)

For inputs: NX-ID4442

For outputs: NX-OD4256

1,000 P2RV-A100C-OMR NX

8 input

points

500 P2RV-A050IC-OMR NX

1,000 P2RV-A100IC-OMR NX

End A End B

Device

end

PLC interface

unit end

L 300

Removable

terminal block

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Schneider Electric

PLC Connecting

Cables

P2RV-@C-SCH-@

32 input

points

500 P2RV-050C-SCH-A

Schneider Electric PLCs with 32-point

connectors (1:4)

For inputs: 140 DDI 353 00

For outputs: 140 DDO 353 00

1,000 P2RV-100C-SCH-A

2,000 P2RV-200C-SCH-A

3,000 P2RV-300C-SCH-A

5,000 P2RV-500C-SCH-A

32 output

points

500 P2RV-050C-SCH-B

1,000 P2RV-100C-SCH-B

2,000 P2RV-200C-SCH-B

3,000 P2RV-300C-SCH-B

5,000 P2RV-500C-SCH-B

16 input

points

500 P2RV-050C-SCH-C

Schneider Electric PLCs with

16-point connectors (1:2)

For inputs: BMX DDI 1602

For outputs: BMX DDO 1602

1,000 P2RV-100C-SCH-C

2,000 P2RV-200C-SCH-C

3,000 P2RV-300C-SCH-C

5,000 P2RV-500C-SCH-C

16 output

points

500 P2RV-050C-SCH-D

1,000 P2RV-100C-SCH-D

2,000 P2RV-200C-SCH-D

3,000 P2RV-300C-SCH-D

5,000 P2RV-500C-SCH-D

Siemens PLC

Connecting Cables

P2RV-@C-SIM-@

32 input

points

500 P2RV-050C-SIM-A

Siemens PLCs with

32-point connectors (1:4)

For inputs: 6ES7 321-1BL00-0AA0

For outputs: 6ES7 322-1BL00-0AA0

1,000 P2RV-100C-SIM-A

2,000 P2RV-200C-SIM-A

3,000 P2RV-300C-SIM-A

5,000 P2RV-500C-SIM-A

32 output

points

500 P2RV-050C-SIM-B

1,000 P2RV-100C-SIM-B

2,000 P2RV-200C-SIM-B

3,000 P2RV-300C-SIM-B

5,000 P2RV-500C-SIM-B

16 input

points

500 P2RV-050C-SIM-C

Siemens PLCs with

16-point connectors (1:2)

For inputs: 6ES7 321-1BH02-0AA0

1,000 P2RV-100C-SIM-C

2,000 P2RV-200C-SIM-C

3,000 P2RV-300C-SIM-C

5,000 P2RV-500C-SIM-C

32 input

points

500 P2RV-050C-SIM-D

Siemens PLCs with

32-point connectors (1:4)

For inputs: 6ES7 421-1BL-0AA0

For outputs: 6ES7 422-1BL-0AA0

1,000 P2RV-100C-SIM-D

2,000 P2RV-200C-SIM-D

3,000 P2RV-300C-SIM-D

5,000 P2RV-500C-SIM-D

32 output

points

500 P2RV-050C-SIM-E

1,000 P2RV-100C-SIM-E

2,000 P2RV-200C-SIM-E

3,000 P2RV-300C-SIM-E

5,000 P2RV-500C-SIM-E

Name Appearance Cable

length L

(mm) Connecting Cables Applicable Connectors

L 300

End A End B

Device

end

PLC interface

unit end

L 300

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Ratings / characteristices

Electrical schematic

Input

P2RVC-8-I-@-1 (PNP) P2RVC-8-I-5 (NPN)

Output

P2RVC-8-O-@-1 (PNP) P2RVC-8-O-5 (NPN)

PLC interface unit

Rated voltage 30 VAC/DC

Rated current 0.5 A/poles, 2 A/unit

Ambient operating temperature −40 to 55°C

Vibration resistance Destruction 10 to 55 to 10 Hz, single amplitude 0.75 mm (double amplitude 1.5 mm)

Malfunction 10 to 55 to 10 Hz, single amplitude 0.75 mm (double amplitude 1.5 mm)

Shock resistance Destruction 300 m/s2

Malfunction 100 m/s2

1....................8

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Dimensions (unit: mm)

PLC interface unit

12.68

67.16

49.60

7×6.20

Push-IN

P2RVC-8-I-5(-1)

P2RVC-8-O-5(-1)

12.68

67.16

49.60

7×6.20

Screw

P2RVC-8-I-7-1

P2RVC-8-O-7-1

G2RV-SR/G3RV-SR

G2RV-SR G3RV-SR Common AccessoriesCommon Precautions

Dimensions (unit: mm)

Short Bars

Separate Plate

Parts for DIN Track Mounting

Refer to your OMRON website for details on the PFP-@.

Safety Precautions

When mounting a short bar

• Intermediate pins can be bent by a tool or by hand and cut off for use.

• The short bar can be cut to as many poles as needed. Insert the

tool from the plastic part side, and cut along the groove in the

plastic part between the terminals. When cutting, take care not to

break or deform the terminals.

However, because the metal on the cut surface will be exposed,

insulation countermeasures between adjacent products must be

ensured. Such countermeasures include widening the intervals

between products or using XW5Z-EP12 separate plates (order

separately).

Mounting a separate plate

• Use a flat-blade screwdriver to tighten the center top screw and

secure the plate. Loosen the screw to remove the plate from the

DIN rail.

(Except for PLC interface unit)

Common Accessories (order separately)

21.20

6.20

Note: Use the Short Bars for crossover wiring within one Socket or between Sockets.

*Replace the box (@) in the model number with the code for the covering color.

Pitch No. of poles L (Length) Colors Model *Maximum carry

current

6.2 mm

2 12.4

Red (R)

Blue (S)

Yellow (Y)

PYDN-6.2-020@

32 A

3 18.6 PYDN-6.2-030@

4 24.8 PYDN-6.2-040@

10 62 PYDN-6.2-100@

20 124 PYDN-6.2-200@

PYDN-6.2-@@ (6.2 mm)

XW5Z-EP12

Precautions for Correct Use

Bend Cut off

Cut

M4 Screw

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have

any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing

by Omron). Omron disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE

PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL

SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products

or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,

to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the

non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price

of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other

claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,

installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by

Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or

unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system

assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in

writing, are not to be construed as an amendment or addition to the above warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is

not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,

or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with

respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it

to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice

to change part numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be

assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to

confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

Authorized Distributor:

In the interest of product improvement,

specifications are subject to change without notice.

Cat. No. J214-E1-02 0617(0316)

OMRON Corporation Industrial Automation Company

OMRON ELECTRONICS LLC

2895 Greenspoint Parkway, Suite 200

Hoffman Estates, IL 60169 U.S.A.

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69, 2132 JD Hoofddorp

The Netherlands

Tel: (31)2356-81-300/Fax: (31)2356-81-388

Contact: www.ia.omron.com

Kyoto, JAPAN

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark,

Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

CSM_6_5_0618