austriamicrosystems AG is now ams AG The technical content of this austriamicrosystems datasheet is still valid. Contact information: Headquarters: ams AG Tobelbaderstrasse 30 8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 e-Mail: ams_sales@ams.com Please visit our website at www.ams.com austriamicrosystems Telephone Line Interface and Speakerphone Circuit AS2522B DATA SHEET - impedance of 1000) as well as a speech circuit with softclipping, line loss compensation and Rx-volume control for handset and handsfree operation. It shall act as an a/bline powered device, which is controlled by a CPU via a serial interface. Furthermore the AS2522 incorporates a DTMF, FSK transmitter, single tone and ringer tone generator. AS2522 allows to use an off-the-shelf microprocessor without special blocks and functions for telephone applications. DTMF, FSK transmitter, single tone and ringer tone generator can be controlled via the serial interface as well as the gain settings in handset and handsfree mode. Applications Enhanced handsfree feature phones with CallerID and extended displays. Package Available in 32-pin TQFP Te ch ni ca Block Diagram AS2522 is a CMOS integrated circuit that incorporates DC and AC line adaptation (DC-mask and synthesized AC- al id - Line/Speech circuit, DTMF dialer, FSK transmitter and tone ringer on a 32-pin CMOS-IC Enhanced voice switching Background noise monitoring DTMF tone generator FSK Transmitter V.23, BELL202, V.21, BELL 103 Ringer tone programmable Tx- and Rx-gain programmable Digital volume control of Rx signals DC characteristic programmable Dual softclipping in handset mode Tx-softclipping in handsfree mode Common monitor amplifier for loudhearing, handsfree and ringing Supply voltage generation for external circuitry Automatic line loss compensation (LLC) Real and complex impedance selectable by external components Side tone adaptation selectable by external components Unique EMC performance Operating range from 15mA to 100mA (down to 5mA with reduced performance) Few external components am lc s on A te G nt st il - General Description lv Key Features Revision 3.4 Page 1 of 19 austriamicrosystems Data Sheet AS2522B Pin description Pin # Symbol 13 LS Function L ine Current S ense Input Analog input for sensing the line current 10 LI L ine I nput 11 RI al id Analog input used for power extraction and line current sensing R eceive I nput Analog input for ac-separated receive signal STB S ide T one B alance Input Analog input for side tone cancellation network 8 CS C urrent S hunt Control Output lv 7 14 CI am lc s on A te G nt st il N-channel open drain output to control the external high power shunt transistor for synthesizing AC- and DC-impedance, modulation of line voltage and shorting the line during make periods of pulse dialing C omplex I mpedance Input Analog input pin for the capacitor to program a complex impedance 12 SS S upply S ource Control Output N-channel open drain output to control the external high power source transistor for supplying (Vpp) the loudspeaker amplifier in off-hook loudspeaking/handsfree mode 9 VSS V oltage S ource S ource Negative Analog Power Supply 18 VDD V oltage D rain D rain Positive Analog Power Supply 19 AGND A nalog G round 6 M1 ca Special ground for the internal amplifiers M icrophone Input 1 Differential input for the handset microphone (electret) M2 M icrophone Input 2 ni 4 ch Differential input for the handset microphone (electret) 5 M3 M icrophone Input 3 Differential input for the handsfree microphone (electret) Te 3 17 M4 M icrophone Input 4 Differential input for the handsfree microphone (electret) RO R eceive O utput to H andset Output for driving a dynamic earpiece with an impedance from 150 to 300 31 OSC O scillator Input Input for ceramic resonator 3.58MHz. Revision 3.4 Page 2 of 19 austriamicrosystems Data Sheet AS2522B Pin # Symbol Function 22 VPP Loudspeaker Power Supply High power supply for the output driver stage 21 CM C onverter M ake Output 27 xCS C hip S elect Chip select input of the serial interface. Internal pull-up resistor ( 100kOhm ) 29 DI D ata I nput 30 CLK Cl oc k lv Data input of the serial interface. Internal pull-up resistor ( 100kOhm ) al id This is an output for controlling the external switching converter. During ringing it converts the ring signal into a 4V supply voltage Clock input of the serial interface. Internal pull-up resistor ( 100kOhm ) DO D ata O utput am lc s on A te G nt st il 28 Data output of the serial interface. If xCS=1 DO is in HI-Z state 24 23 LO1 LO2 1 FT1 2 FT2 20 CBN 15 RECI 16 RECV 25 VSSA 32 VSSD L oudspeaker O utput 1 and 2 Output pins for a 50 loudspeaker Analog input pin for connecting a capacitor for offset cancellation. Analog input pin for connecting a capacitor for offset cancellation. Analog input pin for connecting a capacitor for background noise monitoring. Analog input for the handsfree receive path. Should be connected to RO via coupling capacitor. Analog input for receive voice switching path. Power supply pin for LS1-LS2 output amplifier. V oltage S ource S ource D igital 26 VDDD ca Negative Digital Power Supply V oltage D rain D rain D igital Te ch ni Positive Digital Power Supply Revision 3.4 Page 3 of 19 austriamicrosystems Data Sheet AS2522B Te ch ni ca am lc s on A te G nt st il lv al id Detailed Block Diagram Revision 3.4 Page 4 of 19 austriamicrosystems Data Sheet AS2522B limits the output voltage at RO to 1V p. It prevents harsh distortion and acoustic shock. There is LLC for this path. DC conditions The gain of the LS LO1/LO2 receive path is set to +29dB. This gain can be changed by programming from +22dB to -37dB in 1dB steps. The user can also change the gain via Register VOL (See section "Handsfree"). The receive input is the differential signal of RI and STB. The soft clip circuit limits the output voltage at LO1 of LO2 to 1V p. It prevents harsh distortion and acoustic shock. There is optional LLC for this path. The DC characteristic is determined by the voltage at LIpin and a 30 resistor between LI- and LS-pin. It can be calculated by the following equation: V LS = V LI + I Line * 30. V LI can be programmed to be 3.5V or 4.5V. 2/4 wire conversion AC-impedance The AC-impedance of AS2522 is set to t.m. 1000. With the external capacitor at CI-pin it can be programmed complex. With an external resistor of approx. 1.5k connected to the LS-pin it can be programmed to 600. Side Tone The line loss compensation is programmable (Register 0x0C). When it is activated, the transmit and receive gains for both I/O's are decreased by 6dB at line currents from 20mA to 50mA or from 45mA to 75mA. am lc s on A te G nt st il AS2522 has a built-in dual Wheatstone bridge with one common ground. This provides a maximum of independence of AC-impedance and side tone from each other. One can adapt side tone without changing the ACimpedance. Line Loss Compensation lv The normal operating mode is from 15mA to 100mA. An operating mode with reduced performance is from 5mA to 15mA. In the line hold range from 0mA to 5mA the device is in a power down mode. al id Functional Description Handsfree The handsfree function allows voice communication without using the handset (full 2-way speaker phone). Two voice controlled attenuators prevent acoustic coupling between the loudspeaker and the microphone. The voice switching circuit has three states, namely idle, transmit or receive. In receive mode the attenuation of the receive path and the transmit path can be controlled by Register VOL between 0dB and -20dB. The following table shows how voice switching is controlled A good side tone cancellation can be achieved by using the following equation: Z BAL /Z LINE = 10 Transmit path ca The gain of the M1/M2 LS is set to +37dB. This gain can be changed by programming from +30dB to +45dB in 1dB steps (Register Txgain). The input is differential with ni an impedance of 10k. The soft clip circuit limits the output voltage at LS to 2V p. There is LLC for this path. ch The gain of the M3/M4 LS is set to +46dB. This gain can be changed by programming from +39dB to +54dB in 1dB steps. The input is differential with an Te impedance of 10k. The soft clip circuit limits the output voltage at LS to 2V p . There is no LLC for this path. Receive path The gain of the LS RO receive path is set to +1dB. This gain can be changed by programming from -6dB to +9dB in 1dB steps (Register Rxgain). The receive input is the differential signal of RI and STB. The soft clip circuit Revision 3.4 Page 5 of 19 austriamicrosystems Data Sheet AS2522B voice switching circuit TX_atten Voice switching speech Backgnd noise monitor al id RX Gmax = +9dB Gmin = -21dB ... -40dB (VOL) LINE +23dB +8dB Offset comp Compress Peak detector lv +14dB speech +3dB Voice switching FT2 Peak detector am lc s on A te G nt st il CTXoffset RO CBN RECV RECI Compress Offset comp Compress Peak detector Offset comp FT1 Cmicoffset CBckgnd Gmax = -4dB ... +16dB (VOL) Gmin = -33dB Rx > Tx_atten Tx_atten > Rx Speech Mode Rx-gain Tx-gain Remark X Receive 0db to -20dB -50dB to -30dB adjustable with VOL-setting NO Idle -25 -25 middle position YES Transmit -50dB 0dB independent of VOL-setting ca Tx_atten > Rx IDLE-mode RX-mode TX-mode 0dB ni ch Te Vol max +12dB -10dB TX-gain -20dB Vol default Vol min -25dB -30dB -40dB RX-gain -50dB Revision 3.4 Page 6 of 19 austriamicrosystems Data Sheet AS2522B Serial Interface D7 D6 D5 D4 D3 D2 D1 D0 LLC5 LLC4 LLC3 LLC2 LLC1 LLC0 xPOR POR am lc s on A te G nt st il Power on reset information in Statusbits D1 and D0 lv The settings of the AS2522 are stored in 16 registers. Each register has 4 bit data width. Writing data into the AS2522 also causes the sending of the AS2522 status information on Pin D0. This information consists of the DC-current information (from the Line Loss Compensation circuit) and the status of the power-on reset circuit to test if AS2522 has already powered up. al id Registers D1 D0 0 0 0 1 AS2522 is in POR state 1 0 AS2522 is active 1 1 DC-current information in Statusbits D7 - D2 000000 000001 000011 000111 001111 LLC-bit HI <20mA <45mA 20-26mA 45-51mA 26-32mA 51-57mA 32-38mA 57-63mA 38-44mA 63-69mA 44-50mA 69-75mA >50mA >75mA ni 011111 LLC-bit LO ca D[7:2] Te ch 111111 Revision 3.4 Page 7 of 19 austriamicrosystems Data Sheet AS2522B Timing The data format for writing to a register has the following form: xCS DO D7 A1 D6 A0 D5 D3 D4 D2 D3 D2 The pins xCS,CLK,DI have internal pull-up resistors. Parameter Symbol MIN CLK Pulse width HIGH t6 100ns CLK Pulse width LOW t5 100ns xCS to first falling CLKedge setup time t1 50ns CLK to DOUT delay t2 DIN to CLK setup time DIN to CLK hold time D0 MAX 50ns t4 50ns t6 t4 ca t3 TYP ch DIN D1 ni xCS CLK t2 D0 50ns t3 t5 t1 D1 am lc s on A te G nt st il Note: A2 lv A3 DI al id CLK Te DOUT Revision 3.4 Page 8 of 19 austriamicrosystems Data Sheet AS2522B Serial interface Registers The following table shows the content of the 16 control registers. For a detailed description of the commands see Application note AN522. Address Data Default value after reset Control registers AS2522A, AS2522B A A A A D D D D 3 2 1 0 3 2 1 0 1 DTMFpair CT0 x x x x x x V0 x x M1 M0 x Soft-RX Soft-TX x x x x Revision 3.4 Mask 1 0101 Tone: DTMF-signal path 0...OFF, 1...ON preemph: DTMF-preempahsis 0...2.2dB, 1...3.2dB CT1 CT0: @RO @LO1/LO2 0 0 -36dB -15dB DTMF-confidence level 0 1 -30dB -9dB rel. to pin LS 1 0 -24dB -3dB 1 1 -18dB +3dB Single Tone frequencies if FSK=0 (Addr. 12) and RING/Beep Volum e [4] frequ1 frequ0 V1 0 0 800Hz 0 0 1 1067Hz 0 1 0 1333Hz 1 1 1 1333Hz 1 Tone Generator m ode, single tone path V0: 0 1 0 1 0000 RING volume -17.5dB -11.5dB -5.5dB 0dB 0000 ldbr: Digital tone at RO ldbl: Digital tone at LO1/LO2 MASK: Mask function DC/DC: DC/DC-converter x Bnon 1 Data DTMF-level LOW GROUP at pin LS 0x0 -16dBm : : 0xC -4dBm DTMF-settings 0000 x ring 1 1100 RING: RING-path 0...OFF, BNON: Noise monitor 0...OFF, SOFTRX: Softclip RX 0...OFF, SOFTTX: Softclip TX 0...OFF, DC/DC-Converter ON/OFF,Mask x ldbr 0 DTMF-Level 13 steps, 1dB stepsize 0000 Burl 0 Frequency 0Hz 800Hz (ring) 1067Hz (ring) 1333Hz (ring) 1300Hz (V.23) 2100Hz (V.23) 1200Hz (Bell 202) 2200Hz (Bell 202) 980Hz (V.21) 1180Hz (V.21) 1070Hz (Bell 103) 1270Hz (Bell 103) 1650Hz (V.21) 1850Hz (V.21) 2025Hz (Bell 103) 2225Hz (Bell 103) BURS: Analog tone at RO 0...OFF, 1...ON BURL: Analog tone at LO1/LO2 0...OFF, 1...ON M1 M0: Tone generator mode select 0 0 Tone generator OFF 0 1 DTMF generator mode 1 0 Single tone Analog mode 1 1 Single tone Digital mode ( RING ) Softclip-settings, Noise m onitoring Burs 1 ldbl 1 Te 0 Data f[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ca CT1 x preemph x HIGH Group c1 c0 fHigh 0 0 1209Hz 0 1 1336Hz 1 0 1477Hz 1 1 1633Hz ni 1 x Single tone mode AS2522B ONLY AND FSK=1 (Addr 12): DC/DC 0 0 x V1 1 0 1 ch 0 1 1 0 DTMFLevel Tone 0 0 1 frequ0 0 0 frequ1 0 0000 DTMF-Generator mode: LOW-Group r1 r0 fLow 0 0 697Hz 0 1 770Hz 1 0 852Hz 1 1 941Hz al id 0 lv 0 am lc s on A te G nt st il 0 na No operation. W rite to this location to get AS2522-Satus inform ation without altering any other setting. Frequency select depending on Tone Generator mode f0, r0 0 Nop f2, r1 0 f3, c0 0 f4, c1 0 1...ON 1...ON 1...ON 1...ON 0...OFF, 0...OFF, 0...OFF, 0...OFF, 1...ON 1...ON 1...ON 1...ON Page 9 of 19 austriamicrosystems Data Sheet AS2522B Address Data Control registers AS2522A, AS2522B Default value after reset A A A A D D D D 3 2 1 0 3 2 1 0 0 0 0 0 16 gains Handsfree receive endgain 0111 1 Data RXgain TXgain 0x0 -20dB -30dB Min. receive volume : : 0xF 0dB -50dB Max. receive volume Handsfree switching characteristic 1000 x x x x off1 off0: BGN-offset 0 0 120mV 0 1 180mV 1 0 240mV 1 1 300mV 1 1 0 0 1 1 1 0 0 x x Hfs0 Hfs1 x x Speed of voice switching max speed min speed [16], 16 steps, 1dB stepsize 0111 am lc s on A te G nt st il 1 off0 1 16 gains Data HS-mode HF-mode 0x0 30dB 39dB : : : 0xF 45dB 54dB Receive gain [16], 16 steps, 1dB stepsize off1 0 16 gains Hfs1 HFs0: 0 0 0 1 1 0 1 1 Transmit gain al id 1 0 lv 1 Data HS-mode HF-mode 0x0 -6dB 22dB : : : 0xF +9dB 37dB FSK-mode, LLC[2], LI-Voltage 0111 0111 AS2522B: FSK: Frequency select in single tone mode AS2522B ONLY FSK: 0 Single Tone frequencies are read from Addr. 4: frequ1, frequ0 1 Single Tone frequencies are read from Addr. 1: f4,f3,f2,f1 Llc1 Llc0 x x LIV: Voltage at pin LI 0...3.5V, 1...4.5V LLC1 LLC0: Line loss compensation setting 0 0 20mA-50mA 0 1 NO Line loss compensation 1 0 45-75mA 1 1 NO Line loss compensation Mute, Lh, Hf, Hook Switch 0000 Mute: Mute transmit 0...OFF, 1...ON His Hf Lh 0 x x On Hook 1 0 0 Off Hook, Handset mode 1 1 0 Off Hook, Handfree mode 1 1 1 Off Hook, Loudhearing mode Krat5,Test3,Test2,Test1: For factory test only ! 0000 His x x x x x x x ch Test1 Hf ni ca Liv x Test2 0 x Lh 1 1 Mute 1 0 Krat5 1 1 Test3 1 FSK AS2522A FSK: For factory test only ! 1 1 1 x Reset to defaults na Te 1 Revision 3.4 Page 10 of 19 austriamicrosystems Data Sheet AS2522B Electrical characteristics Electrical characteristics are measured with the Test Circuit application. Typical mean values will not be tested. al id Absolute maximum ratings Positive Supply Voltage -0.3V <= V DD <= 7V Input Current +/- 25mA Input Voltage (LS) -0.3V <= V in <= 12V -0.3V <= V in <= 8V lv Input Voltage (LI, CS) Input Voltage (STB, RI) -0.3V <= V in <= V DD +0.3V am lc s on A te G nt st il Digital Input Voltage -2V <= V in <= V DD +0.3V +/- 1000V Electrostatic Discharge (HBM 1.5k-100pF) Storage Temperature -65C to +125C Recommended operating conditions Supply Voltage (generated internally) 3V <= V DD <= 5V Operating Temperature DC characteristics -25C to +70C ca I Line =15mA w/o operation of any additional external circuitry, unless other specified Parameter Type Max Units Test Speech Mode 3 6 mA Y Operating Current Handsfree Mode 7 10 mA Y Line Voltage LIVolt=0 Line Voltage LIVolt=1 15mA<=ILINE<=100mA 3.5 4.5 3.8 4.8 V V Y Y mA N I DDS Operating Current I DDH ni Symbol ch V LI Output Current, Sink CS,SS Te I OL Revision 3.4 Conditions VOL=0.4V Min 3.2 4.2 1 Page 11 of 19 austriamicrosystems Data Sheet AS2522B Transmit characteristics I Line =15mA f=800Hz, default settings unless other specified Symbol A M1/2TX Parameter Transmit Gain Conditions Min Type Max Units Test Z AC(syn)= 1000 35 +36.5 38 dB Y Z AC(syn) =1000 43 +45.0 47 dB A M3/4TX Transmit Gain M3/M4 LS al id M1/M2 LS Y A TX Variation with frequency f = 500Hz ... 3.4kHz 0.8 dB A VRM12 Control range 16 steps -7/+8 dBr N 16 steps -7/+8 dBr N A VRM34 Control range am lc s on A te G nt st il M2/M4 LS lv M1/M2 LS THD Distortion V AGC1 Soft Clip Level V LS =0.25VRMS N 2 % Y 2 VP N 2 VP N M1/M2 LS at LS V AGC2 Soft Clip Level Soft Clip Overdrive M1/M2 - M3/M4 20 dB N t attack Attack time 70 us/6dB N t decay Decay time 100 ms/6dB N Z IN-M1/2 Input Impedance M1/M2 10 k N Z IN-M3/4 Input Impedance M3/M4 10 k N V INmax Input Voltage Range M1/2 - M3/4 differential 1 Vp N V NO T AMP =25C dBmp Y Mute Attenuation Mute activated dB Y ca A SCO ni M3/M4 LS at LS ch Noise Output Voltage LS Handset mode Gain = 36.5dB 60 Te A MUTE -72 Revision 3.4 Page 12 of 19 austriamicrosystems Data Sheet AS2522B Receive characteristics I Line =15mA f=800Hz, default settings unless other specified A RO Conditions Receive Gain Z AC(syn) =1000 LS RO Vol default Min Type Max Units Test -2 -0.5 1 dB Y +28 +29.0 +31 dB Receive Gain Z AC(syn) =1000 LS LO1/LO2 Vol maximum A RX Variation with frequency f=500Hz to 3.4kHz 0.8 dB A VRRO Control range 16 steps -7/+8 dBr N 16 steps -7/+8 dBr N LS RO A VRLS Control range am lc s on A te G nt st il LS LS1/LS2 Y N lv A LO12 Parameter al id Symbol THD LS Distortion LS1/LS2 V LS =0.25VRMS 5 % Y THD RO Distortion RO V LS =0.25VRMS 2 % Y V UFC Unwanted Freq. Cmp. f = 200 ... 20kHz -60 dBm Y 1 VP N V AGCRO Soft Clip Level RO V AGCLS Soft Clip Level LS1/2 2 VP N A SCLS Soft Clip Overdrive LS1/2 10 dB N t attack Attack time 70 us/6dB N t decay Decay time 100 ms/6dB N V NO Noise Output Voltage RO dBmp Y ca Gain = 3dB Input Imp. RI Input Voltage Range RI 8 2 k Vp N Input Imp. STB Input Volt. Range STB 80 2 k Vp N dB Y dB Y ch Z IN-STB V INmax -72 ni Z IN-RI V INmax T AMP =25C Side tone V RI <=0.25VRMS 26 RL Z AC/C Return Loss Temp. Variation Z AC(syn) =1000 18 Te ST Revision 3.4 0.5 /C Page 13 of 19 austriamicrosystems Data Sheet AS2522B DTMF characteristics I Line =15mA w/o operation of any additional external circuitry, unless other specified, default settings Conditions Tone level low group at LS Default MF range DTMF level range low group at LS 13 steps Prg. in Service mode V L-H Preemphasis L-H Preemphasis=1 UFC Unwanted frequency components 300 Hz - 4.3kHz 4.3kHz - 7kHz 7kHz - 10kHz 10kHz - 14kHz 14kHz - 28.5kHz 28.5kHz - 40kHz f Frequency deviation V CT-H Comfort tone handset Rel to LS programmable in service mode V CT-L Comfort tone Loudspeaker Rel to LS programmable in service mode Ringer Parameter ca Symbol 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ni Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Te ch F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 Revision 3.4 Type Max Units Test -7 -6 -5 dBm Y -18/-6 2.7 dBm N 3.7 dB Y -40 -46 -52 -58 -70 -80 dBm dBm dBm dBm dBm dBm Y Y Y Y Y Y 1.2 % Y -36 -30 -24 -18 dBr dBr dBr dBr N N N N -15 -9 -3 +3 dBr dBr dBr dBr N N N N Units Test Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz N Y Y Y N N N N N N N N N N N N 3.2 am lc s on A te G nt st il V MFlow Min al id Parameter lv Symbol Conditions Min 770 1025 1280 Type 0 800 1067 1333 1300 2100 1200 2200 980 1180 1070 1270 1650 1850 2025 2225 Max 830 1110 1385 Page 14 of 19 austriamicrosystems Data Sheet AS2522B Miscellaneous Symbol Parameter Conditions Min Type Max Units Test Pacifier level at RO RL = 150 Ohm 30 mV pp N V PALS Pacifier level at LS1/2 RL = 50 Ohm 100 mV pp N Test circuit al id V PARO 15nF 10V LS M3 15nF 11 30 10 RI M4 LI 3 15nF am lc s on A te G nt st il 600 Iline 5 lv 100uF 10uF 13 M1 300 6 1uF Vac 15nF 7 BC327 8 6k 14 STB M2 CS 10uF RO 17 CI 100nF RECI 32 9 4 VSSD VSS 15 16 AS2522A 12 SS LO2 22 10k 100nF RECV BC327 150 10k 23 VPP OSC CBN 27 28 29 30 31 20 FT2 10uF 1uF 1 1uF 2 FT1 AGND VDDD 19 18 VDD CM 100uF 5V1 xCS DO DI CLK 3.58MHz Resonator Te ch ni ca 21 24 VSSA 22uF 25 26 470uF 50 LO1 Revision 3.4 Page 15 of 19 austriamicrosystems Data Sheet AS2522B Te ch ni ca am lc s on A te G nt st il lv al id Typical application Revision 3.4 Page 16 of 19 austriamicrosystems Data Sheet AS2522B am lc s on A te G nt st il lv al id Bonding Diagram Te ch ni ca 32 Lead 7x7mm TQFP dimensions Revision 3.4 Page 17 of 19 austriamicrosystems Data Sheet AS2522B Packaging Ordering Information Number Package Description AS2522B Q TQFP plastic thin quad flat package - 32 leads (suffix T) Pin-out, Marking AS2522B F DOF Dice-on-Foil LO1 LO2 VPP CM CBN AGND VDD RO am lc s on A te G nt st il YYWWAAA AS2522X 24 23 22 21 20 19 18 17 year of production calendar week of production austriamicrosystems AG assembly ID X revision Te ch ni ca YY WW AAA Revision 3.4 al id 1 2 3 4 5 6 7 8 VSS 9 LI 10 RI 11 SS 12 LS 13 CI 14 RECI 15 RECV 16 FT1 FT2 M4 M2 M3 M1 STB CS Devices sold by austriamicrosystems AG are covered by the warranty and patent identification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. lv 32 31 30 29 28 27 26 25 VSSD OSC CLK DI DO xCS VDDD VSSA 32-pin plastic TQFP (suffix Q) For exact mechanical package dimensions please see austriamicrosystems AG packaging information. Copyright Copyright (c) 1997-2002, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Page 18 of 19 austriamicrosystems Data Sheet AS2522B Contact Headquarters al id austriamicrosystems AG Communications Business Unit A 8141 Schloss Premstatten, Austria T. +43 (0) 3136 500 0 F. +43 (0) 3136 525 01 www.austriamicrosystems.com USA (east) Germany austriamicrosystems USA, Inc. Suite 400, 8601 Six Forks Road Raleigh, NC 27615, USA Phone: +1/919/676 5292 Fax: +1/919/676 5305 am lc s on A te G nt st il austriamicrosystems Germany GmbH Tegernseer Landstrasse 85 D-81539 Munchen, Germany Phone: +49/89/693643-0 Fax: +49/89/693643-66 lv Sales Offices United Kingdom France austriamicrosystems France S.a.r.l. 124, Avenue de Paris F-94300 Vincennes, France Phone: +33/1/43 74 00 90 Fax: +33/1/43 74 20 98 austriamicrosystems UK, Ltd. Coliseum Business Centre, Watchmoor Park Camberley, Surrey, GU15 3YL, UK Phone: +44/1276/23 3 99 Fax: +44/1276/29 3 53 Japan Italy Switzerland ca austriamicrosystems Italy S.r.l. Via Leone Tolstoi, 64 I-20146 Milano, Italy Phone: +39/0242/36713 Fax: +39/0242/290889 austriamicrosystems AG Shin Yokohama Daini, Center Bldg. 10F 3-19-5, Shin Yokohama Kohoku-ku, Yokohama 222-0033, Japan Phone: +81/45/474 0962 Fax: +81/45/472 9845 Distributors & Representatives USA (west) Spain, Israel, Korea, Hong-Kong, Taiwan, Malaysia, Singapore, India, Brazil Te ch ni austriamicrosystems Switzerland AG Rietstrasse 4 CH-8640 Rapperswil, Switzerland Phone: +41/55/220 9000 Fax: +41/55/220 9001 austriamicrosystems USA, Inc. Suite 116, 4030 Moorpark Ave, San Jose, CA 95117, USA Phone: +1/408/345 1790 Fax: +1/408/345 1795 Revision 3.4 austriamicrosystems AG is represented by distributors in the following countries. Please contact your nearest regional sales office for the distributor address: Application Support Please contact your local sales office or your distributor. Page 19 of 19