247
TACT SwitchTM Sharp
Feeling Soft
Feeling Snap-in
Type Surface
Mount Type Radial
Type
Low-profile surface mount type with high operation
force most suitable for in-car components
6.6×6.3mm High Operation Force (Surface Mount Type)
SKPG
Style PC board land dimensions
（Viewed from switch mounting face）
1, 2 0 0
Japan Export
■Product Line
Operating force
2.45N
2.94N
1.18 N
Product No.
SKPGAAE010
SKPGABE010
SKPGACE010
Operating life
（1mA 5V DC）
50,000 cycles
Minimum order unit （pcs.）
1, 2 0 0
Rubber color
Green
Blue
Light blue
Top push
Operating direction
■Circuit Diagram
12
■Dimensions Unit:mm
12
9.8
6.8
2.4
■Packing Specifications
Taping
Reel size
Unit:mm
■Typical Specifications
Items Specifications
Rating （max.）
5mA 12V DC
Rating （min.）
10μA 1V DC
Initial contact resistance
1kΩ max.
Travel （mm）
1.3
Refer to P.249 for soldering conditions.
Number of packages （pcs.） Tape width
（mm）
Export package
measurements （mm）
1 reel 1 case / Japan
1 case / export packing
1, 2 0 0 9,600 9,600 16 395×395×205
For reels of 330mm diameter, please inquire.
Note
185
TACT SwitchTM Sharp
Feeling Soft
Feeling Snap-in
Type Surface
Mount Type Radial
Type
Sharp
Feeling Soft
Feeling Snap-in
Type Surface
Mount Type Radial
Type
Type Sharp Feeling Type Soft Feeling Type
Surface Mount Snap–in Surface Mount
Series
SKSC SKRT SKRH
SKPF SKPS SKPM SKPG SKPR
Photo
Features
Low–profile —
4–direction
switch
＋push switch
High operation force
Long travel
Low contact resistance —
High operation force
Low contact resistance
Water-proof
————————
Dust-proof
————————
IP standard
————————
Operating
direction
Top push
——●●●●●●
Side push
●●●—————
Dimensions
（mm）
W
3.5 4.5 7. 3 5 85.9 6.6 7. 5
D
3.55 3.4 7. 5 9 6 6.3 7. 8
H
1. 2 5 3.3 510 56.5
Contact
———Carbon Silver Carbon Silver
Operation
force
coverage
1N max.
See the
relevant pages
for respective
product
descriptions
1N to 2N
2N to 3N
3N to 4N
4N to 5N
Travel （mm）
0.2 1. 7 5
See the relevant
pages for respective
product descriptions
1. 0 5 1. 3 1
Ground terminal
○●●—————
Operating temperature
range
−30℃ to ＋85℃
−
40℃ to ＋90℃
−
40℃ to ＋85℃
−40℃ to ＋90℃
Automotive use
———●●●●●
Life Cycle
Electrical
performance
Rating （max.）
（Resistive load）
50mA
12 V D C
50mA
16 V D C
5mA
12 V D C
50mA
16 V D C
Rating （min.）
（Resistive load）
10μA 1V D C
Insulation
resistance
10 0 MΩ min . 100 V D C 1min .
Voltage proof
10 0 V A C
1m i n .
250V AC
1m i n .
10 0 V A C
1m i n . 250V AC 1min.
Durability
Vibration
10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies,
in the 3 direction of X, Y and Z for 2 hours respectively
Lifetime
Shall be in accordance with individual specifications.
Environmental
performance
Cold
−40℃ 96h −40℃ 1,000h −40℃ 96h
−40℃ 1,000h
Dry heat
90℃ 96h 90℃ 1,000h 90℃ 96h 90℃ 1,000h
Damp heat
60℃, 90 to 95%RH 96h
60℃, 90 to 95%RH 1,000h
60℃, 90 to
95%RH 96h
60℃, 90 to
95%RH 1,000h
Page
239 241 444 244 245 246 247 248
TACT SwitchTM Soldering Conditions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 249
TACT SwitchTM Cautions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 250
Notes
1. The automotive operating temperature range to be individually discussed upon request.
2. ● Indicates applicability to all products in the series.
W：Width. The most outer dimension excluding terminal portion.
D ：Depth. The most outer dimension excluding terminal portion.
H ：Height. The minimum dimension if there are variances.
249
TACT SwitchTM Sharp
Feeling Soft
Feeling Snap-in
Type Surface
Mount Type Radial
Type
Sharp
Feeling Soft
Feeling Snap-in
Type Surface
Mount Type Radial
Type
TACT SwitchTM / Soldering Conditions
Temperature profile
■Condition for Reflow
Available for Surface Mount Type.
180
150
260˚C max. 3s max.
230˚C
Time
120s max.
（pre-heating）
3 to 4min.
Time inside soldering equipment
Temperature (˚C )
40s max.
1. Prevent flux penetration from the top side of the TACT SwitchTM.
2. Switch terminals and a PC board should not be coated with flux prior to soldering.
3. The second soldering should be done after the switch is stable with normal temperature.
4. Use the flux with a specific gravity of min 0.81.
（EC-19S-8 by TAMURA CORPORATION, or equivalents.）
Notes
1. Please confirm the specifications of our product for the detailed condition.
2. Soldering conditions differ depending on reflow soldering machines.
Prior verification of soldering condition is highly recommended.
Notes
■Conditions for Auto-dip
Available for Snap-in Type and Radial Type.
Items Condition
Flux built-up
Mounting surface should not be exposed to flux
Preheating temperature
Ambient temperature of the soldered surface of PC board. 100℃ max.
Preheating time
60s max.
Soldering temperature
260℃ max.
Duration of immersion
5s max.
Number of soldering
2times max.
SKHH Series
Items Condition
Flux built-up
Mounting surface should not be exposed to flux
Preheating temperature
Ambient temperature of the soldered surface of PC board. 110℃ max.
Preheating time
60s max.
Soldering temperature
260℃ max.
Duration of immersion
5s max.
Number of soldering
2times max.
SKHLTop Push Type, SKQJ
Series
Items Condition
Flux built-up
Mounting surface should not be exposed to flux
Preheating temperature
Ambient temperature of the soldered surface of PC board. 100℃ max.
Preheating time
45s max.
Soldering temperature
255℃ max.
Duration of immersion
5s max.
Number of soldering
2times max.
■Manual Soldering
Items Condition
Soldering temperature
350℃ max.
Duration of soldering
3s max.
Capacity of soldering iron
60W max.
SKHH, SKHW Series
Items Condition
Soldering temperature
360℃ max.
Duration of soldering
3s max.
Capacity of soldering iron
60W max.
SKTD, SKTG, SKQJ Series
Items Condition
Soldering temperature
350℃ max.
Duration of soldering
3s max.
Capacity of soldering iron
20W max.
