HDSP-A2xC Series Alphanumeric Display, 0.54" (13.7 mm) 2 Character As AlInGaP Red Data Sheet Description These 0.54" (13.7 mm) AS AlInGaP displays are available in either common anode or common cathode. Features * As AlInGaP red color * Gray face paint Gray package gives optimum contrast * Design flexibility Common anode or common cathode Devices As AlInGaP Red HDSP-A22C HDSP-A27C Description Common Anode Common Cathode Applications * Suitable for alphanumeric * Operating temperature range -40C to 105C Package Dimensions 1.20 [0.047] 8.17 [0.322] 13.80 [0.543] 21.00 [0.827] 15.24 [0.600] 6.75 5.95 [0.266] [0.234] 25.20 [0.992] 7.00 [0.276] 20.32 [0.800] 3.70 [0.146] NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS [INCHES] 2. UNLESS OTHERWISE STATED, TOLERANCES ARE 0.25 mm Internal Circuit DIG 1 DIG 2 A F P G H B N J E M L K C D DP1 12 A 10 9 B A C B 7 D C 1 E D 18 F E 15 G F 14 H G COM 2 DIG 2 DP2 6 J 5 K H J 4 2 L K M L 13 8 P N M 17 DP1 P N COM 1 DIG 1 16 11 DP2 COMMON ANODE COM 2 DIG 2 12 A 10 9 B A C B 7 D C 1 E D 18 F E 15 G F 14 H G 6 J H 5 K J 4 L K 2 M L 13 N 8 DP1 P N M 17 COM 1 DIG 1 16 11 P DP2 COMMON CATHODE Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Pin Configuration A Common Anode 1E/2E Cathode 1M/2M Cathode No Connection 1L/2L Cathode 1K/2K Cathode 1J/2J Cathode 1D/2D Cathode DP1 Cathode 1C/2C Cathode 1B/2B Cathode DIGIT No. 2 Common Anode 1A/2A Cathode 1N/2N Cathode 1H/2H Cathode 1G/2G Cathode DIGIT No. 1 Common Anode 1P/2P Cathode 1F/2F Cathode Pin Configuration B Common Cathode 1E/2E Anode 1M/2M Anode No Connection 1L/2L Anode 1K/2K Anode 1J/2J Anode 1D/2D Anode DP1 Anode 1C/2C Anode 1B/2B Anode DIGIT No. 2 Common Cathode 1A/2A Anode 1N/2N Anode 1H/2H Anode 1G/2G Anode DIGIT No. 1 Common Cathode 1P/2P Anode 1F/2F Anode Absolute Maximum Ratings at TA = 25C Parameter DC Forward Current per Segment or DP[1,2,3] Peak Forward Current per Segment or DP[2,3] Average Forward Current[3] Reverse Voltage per Segment or DP (IR = 100 A) Operating Temperature Storage Temperature Wavesoldering Conditions Symbol IF IPEAK IAVE VR TO TS Temperature Time HDSP-A22C/HDSP-A27C 50 100 30 5 -40 to +105 -40 to +120 250 3 Units mA mA mA V C C C s Notes: 1. Derate linearly as shown in Figure 1. 2. For long term performance with minimal light output degradation, drive currents between 10 mA and 30 mA are recommended. For more information on recommended drive conditions, please refer to Application Brief I-024 (5966-3087E). 3. Operating at currents below 1 mA is not recommended. Please contact your local representative for further information. Optical/Electrical Characteristics at TA = 25C Device Series HDSPA22C A27C Parameter Forward Voltage Reverse Voltage Peak Wavelength Symbol IV VR PEAK Min. 1.70 5 Typ. 1.90 20 635 Max. 2.20 Units V V nm Dominant Wavelength[3] Spectral Halfwidth d 1/2 622.5 626 17 630 nm nm Speed of Response s 20 ns Capacitance C 40 pF Intensity Bin Limits[1] (mcd at 10 mA) Bin Name Min.[2] T 18.0 U 25.0 Max.[2] 25.0 36.0 Notes: 1. Bin categories are established for classification of products. Products may not be available in all bin categories. 2. Tolerance for each bin limit is 10%. 3 Test Conditions IF = 20 mA IF = 100 A Peak Wavelength of Spectral Distribution at IF = 20 mA Wavelength Width at Spectral Distribution 1/2 Power Point at IF = 20 mA Exponential Time Constant, e-ts VF = 0, f = 1 MHz 50 40 30 20 10 0 0 20 40 60 80 100 120 TA - AMBIENT TEMPERATURE - C Figure 1. Maximum forward current vs. ambient temperature. Derating based on TJMAX = 130C. IF - FORWARD CURRENT PER SEGMENT - mA IF - MAXIMUM AVERAGE CURRENT - mA 60 120 Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. 100 80 60 40 20 0 0 1.0 1.5 2.0 2.5 3.0 VF - FORWARD VOLTAGE - V Figure 2. Forward current vs. forwrad voltage. Soldering/Cleaning Cleaning agents from ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs, please refer to Application Note 1027. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright (c) 2006 Avago Technologies Limited. All rights reserved. Obsoletes 5980-2919EN 5988-4821EN June 23, 2006