LTC1734L Lithium-Ion Linear Battery Charger in ThinSOT U FEATURES DESCRIPTIO Low Profile (1mm) ThinSOTTM Package Programmable Charge Current: 50mA to 180mA No Blocking Diode Required No Sense Resistor Required 1% Accurate Preset Voltage: 4.2V Charge Current Monitor Output for Charge Termination Automatic Sleep Mode with Input Supply Removal Manual Shutdown Negligible Battery Drain Current in Shutdown Undervoltage Lockout Self Protection for Overcurrent/Overtemperature U APPLICATIO S The LTC(R)1734L is a low cost, single cell, constant-current/ constant-voltage Li-Ion battery charger controller. When combined with a few external components, the SOT-23 package forms a very small, low cost charger for single cell lithium-ion batteries. The LTC1734L is a lower charge current version of the LTC1734. The LTC1734L provides a fixed float voltage of 4.2V with 1% accuracy (for 4.1V and 4.15V float voltages, contact LTC Marketing). Constant current is programmed using a single external resistor between the PROG pin and ground. Manual shutdown is accomplished by floating the program resistor while removing input power automatically puts the LTC1734L into a sleep mode. Both the shutdown and sleep modes drain near zero current from the battery. Charge current can be monitored via the voltage on the PROG pin allowing a microcontroller or ADC to read the current and determine when to terminate the charge cycle. The output driver is both current limited and thermally protected to prevent the LTC1734L from operating outside of safe limits. No external blocking diode is required. Cellular Telephones Handheld Computers Digital Cameras Charging Docks and Cradles Low Cost and Small Size Chargers Programmable Current Sources , LTC and LT are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. The LTC1734L can also function as a general purpose current source or as a current source for charging nickelcadmium (NiCd) and nickel-metal-hydride (NiMH) batteries using external termination. U TYPICAL APPLICATIO PROG Pin Indicates Charge Status 5V 1F VCC ISENSE 1 2 LTC1734L 6 GND DRIVE 4 5 RPROG 4.7k PROG BAT VBAT 4V 3V UMT4403 IBAT = 80mA 10F + 2V SINGLE Li-Ion BATTERY VPROG (V) 3 VIN 5V VBAT (V) 80mA Li-Ion Battery Charger CONSTANT CURRENT 1.5V CONSTANT VOLTAGE VPROG 1V 1734 TA01 0V CHARGING BEGINS CHARGING COMPLETE 1734 TA01b 1734lf 1 LTC1734L W U U U W W W ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDER INFORMATION (Note 1) Input Supply Voltage (VCC) ..........................- 0.3V to 9V Input Voltage (BAT, PROG) ........ - 0.3V to (VCC + 0.3V) Output Voltage (DRIVE) .............. - 0.3V to (VCC + 0.3V) Output Current (ISENSE) ................................... - 210mA Short-Circuit Duration (DRIVE) ...................... Indefinite Junction Temperature .......................................... 125C Operating Ambient Temperature Range (Note 2) ...............................................-40C to 85C Operating Junction Temperature (Note 2) ............ 100C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C ORDER PART NUMBER TOP VIEW ISENSE 1 GND 2 VCC 3 LTC1734LES6-4.2 6 DRIVE 5 BAT 4 PROG S6 PART MARKING S6 PACKAGE 6-LEAD PLASTIC SOT-23 LTE6 TJMAX = 125C, JA = 230C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, unless otherwise noted specifications are at TA = 25C. VCC = 5V, GND = 0V and VBAT is equal to the float voltage unless otherwise noted. All current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VCC Supply VCC Input Supply Voltage (Note 5) 8 V ICC Quiescent VCC Pin Supply Current VBAT = 5V, (Forces IDRIVE = IBAT = 0), IPROG = 200A,(7500 from PROG to GND) 670 1150 A ISHDN VCC Pin Supply Current in Manual Shutdown PROG Pin Open 450 900 A IBMS Battery Drain Current in Manual Shutdown (Note 3) PROG Pin Open -1 0 1 A IBSL Battery Drain Current in Sleep Mode (Note 4) VCC = 0V -1 0 1 A VUVLOI Undervoltage Lockout Exit Threshold VCC Increasing 4.45 4.56 4.68 V VUVLOD VUVHYS Undervoltage Lockout Entry Threshold VCC Decreasing 4.30 4.41 4.53 Undervoltage Lockout Hysteresis VCC Decreasing 4.55 150 V mV Charging Performance VBAT Output Float Voltage in Constant Voltage Mode IBAT = 10mA, 4.55V VCC 8V 4.158 4.20 4.242 IBAT1 Output Full-Scale Current When Programmed for 50mA in Constant Current Mode RPROG = 7500, 4.55V VCC 8V, Pass PNP Beta > 50 39 50 60 mA IBAT2 Output Full-Scale Current When Programmed for 180mA in Constant Current Mode RPROG = 2100, 4.55V VCC 8V, Pass PNP Beta > 50 160 180 200 mA VCM1 Current Monitor Voltage on PROG Pin IBAT = 10% of IBAT1, RPROG = 7500, 4.55V VCC 8V, Pass PNP Beta > 50, 0C TA 85C 0.045 0.15 0.28 V VCM2 Current Monitor Voltage on PROG Pin IBAT = 10% of IBAT2, RPROG = 2100, 4.55V VCC 8V, Pass PNP Beta > 50, 0C TA 85C 0.10 0.15 0.20 V IDSINK Drive Output Current VDRIVE = 3.5V 20 V mA 1734lf 2 LTC1734L ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 5V, GND = 0V and VBAT is equal to the float voltage unless otherwise noted. All current into a pin is positive and current out of a pin is negative. All voltages are referenced to GND, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX 2.05 2.15 2.25 UNITS Charger Manual Control VMSDT Manual Shutdown Threshold VPROG Increasing VMSHYS Manual Shutdown Hysteresis VPROG Decreasing from VMSDT IPROGPU Program Pin Pull-Up Current VPROG = 2.5V Drive Output Short-Circuit Current Limit VDRIVE = VCC V 90 mV -6 -3 - 1.5 A 35 65 130 mA Protection IDSHRT Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC1734LE is guaranteed to meet performance specifications from 0C to 70C ambient temperature range and 0C to 100C junction temperature range. Specifications over the - 40C to 85C operating ambient temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Assumes that the external PNP pass transistor has negligible B-C reverse-leakage current when the collector is biased at 4.2V (VBAT) and the base is biased at 5V (VCC). Note 4: Assumes that the external PNP pass transistor has negligible B-E reverse-leakage current when the emitter is biased at 0V (VCC) and the base is biased at 4.2V (VBAT). Note 5: The 4.68V maximum undervoltage lockout (UVLO) exit threshold must first be exceeded before the minimum VCC specification applies. Short duration drops below the minimum VCC specification of several microseconds or less are ignored by the UVLO. If manual shutdown is entered, then VCC must be higher than the 4.68V maximum UVLO threshold before manual shutdown can be exited. When operating near the minimum VCC, a suitable PNP transistor with a low saturation voltage must be used. U W TYPICAL PERFOR A CE CHARACTERISTICS Float Voltage vs Temperature and Supply Voltage 4.201 4.20 VCC = 8V 52 VCC = 5V TA = 25C PNP = FCX589 RPROG = 2100 4.200 VCC = 4.55V 4.19 -50 -25 50 25 0 75 TEMPERATURE (C) RPROG = 7.5k PNP = FCX589 51 IBAT1 (mA) IBAT = 10mA PNP = FCX589 FLOAT VOLTAGE (V) FLOAT VOLTAGE (V) 4.21 IBAT1 vs Temperature and Supply Voltage Float Voltage vs IBAT 50 VCC = 4.55V AND 8V 49 100 125 1734 G01 4.199 0 25 50 75 100 IBAT (mA) 125 150 175 1734 G02 48 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 1734 G03 1734lf 3 LTC1734L U W TYPICAL PERFOR A CE CHARACTERISTICS IBAT2 vs Temperature and Supply Voltage IBAT1 vs VBAT 52 180 VCC = 4.55V AND 8V 170 -50 -25 50 25 0 75 TEMPERATURE (C) 100 VCC = 5V TA = 25C RPROG = 7.5k PNP = FCX589 50 BAT PIN MUST BE DISCONNECTED AND GROUNDED TO FORCE CC MODE IN THIS REGION 48 125 IBAT2 vs VBAT 190 IBAT2 (mA) RPROG = 2.1k PNP = FCX589 IBAT1 (mA) IBAT2 (mA) 190 1 0 3 2 VBAT (V) 4 Program Pin Pull-Up Current vs Temperature and Supply Voltage 3.6 3.5 1.6 VCC = 8V TA = 25C 1.2 3.2 VPROG (V) IPROGPU (A) IPROGPU (A) 5 VCC = 5V TA = 25C RPROG = 7.5k PNP = FCX589 1.4 3.4 VCC = 4.55V 4 Program Pin Voltage vs Charge Current (50mA) VCC = 8V 3.3 3 2 VBAT (V) 1734 G06 Program Pin Pull-Up Current vs VPROG VPROG = 2.5V 3.4 1 0 1734 G05 1734 G04 3.6 BAT PIN MUST BE DISCONNECTED AND GROUNDED TO FORCE CC MODE IN THIS REGION 180 170 5 VCC = 5V TA = 25C RPROG = 2.1k PNP = FCX589 3.0 1.0 0.8 0.6 3.2 0.4 0.2 2.6 50 25 75 0 TEMPERATURE (C) 100 125 2 3 4 5 6 VPROG (V) 7 0 8 160 1.6 VCC = 5V T = 25C 1.4 A RPROG = 2.1k PNP = FCX589 1.2 VPROG (mV) 0.8 0.6 20 10 30 IBAT1 (mA) Program Pin Voltage for IBAT2/10 vs Temperature and Supply Voltage 160 RPROG = 7.5k PNP = FCX589 VCC = 8V 150 50 40 1734 F09 Program Pin Voltage for IBAT1/10 vs Temperature and Supply Voltage Program Pin Voltage vs Charge Current (180mA) 1.0 0 1635 G08 1734 G07 VPROG (mV) 3.0 -50 -25 VPROG (V) LIMITS AT 25mV DUE TO PROGRAMMING PIN PULL-UP CURRENT (IPROGPU) 2.8 3.1 RPROG = 2.1k PNP = FCX589 VCC = 8V 150 VCC = 4.55V VCC = 4.55V 0.4 LIMITS AT 6mV DUE TO PROGRAMMING PIN PULL-UP CURRENT (IPROGPU) 0.2 0 0 45 90 135 180 IBAT2 (mA) 1734 G10 140 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 1734 G11 140 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125 1734 G12 1734lf 4 LTC1734L U U U PIN FUNCTIONS ISENSE (Pin 1): Sense Node for Charge Current. Current from VCC passes through the internal current sense resistor and reappears at ISENSE to supply current to the external PNP emitter. The PNP collector provides charge current to the battery. GND (Pin 2): Ground. Provides a reference for the internal voltage regulator and a return for all internal circuits. When in the constant voltage mode, the LTC1734L will precisely regulate the voltage between the BAT and GND pins. The battery ground should connect close to the GND pin to avoid voltage drop errors. VCC (Pin 3): Positive Input Supply Voltage. Supplies power to the internal control circuitry and external PNP transistor through the internal current sense resistor. This pin should be bypassed to ground with a capacitor in the range of 1F to 10F. PROG (Pin 4): Charge Current Programming, Charge Current Monitor and Manual Shutdown Pin. Provides a virtual reference voltage of 1.5V for an external resistor (RPROG) tied between this pin and ground that programs the battery charge current when the charger is in the constant current mode. The typical charge current will be 250 times greater than the current through this resistor W BLOCK DIAGRA (IBAT = 375/RPROG). This pin also allows for the charge current to be monitored. The voltage on this pin is proportional to the charge current where 1.5V corresponds to the full programmed currrent. Floating this pin allows an internal current source to pull the pin voltage above the shutdown threshold voltage. Because this pin is in a signal path, excessive capacitive loading can cause AC instability. See the Applications Information section for more details. BAT (Pin 5): Battery Voltage Sense Input. A precision internal resistor divider sets the final float voltage on this pin. This divider is disconnected in the manual shutdown or sleep mode. When charging, approximately 34A flows into the BAT pin. To minimize float voltage errors, avoid excessive resistance between the battery and the BAT pin. For dynamically stable operation, this pin usually requires a minimum bypass capacitance to ground of 5F to frequency compensate for the high frequency inductive effects of the battery and wiring. DRIVE (Pin 6): Base Drive Output for the External PNP Pass Transistor. Provides a controlled sink current that drives the base of the PNP. This pin has current limiting protection for the LTC1734L. VIN 1F VCC 3 IBAT/250 IBAT 60 0.24 ISENSE 1 VOLTAGE REFERENCE 2.5V UVLO SHUTDOWN + - REF OUTPUT DRIVER A3 SHUTDOWN DRIVE 6 TEMPERATURE AND CURRENT LIMITING IBAT C1 2.15V + 1.5V + SHUTDOWN + A2 - - BAT 2.5V 5 10F A1 SINGLE Li-Ion CELL - 3A SHUTDOWN 4 PROG 2 1734 BD GND RPROG 1734lf 5 LTC1734L U OPERATIO The LTC1734L is a linear battery charger controller. Operation can best be understood by referring to the Block Diagram. Charging begins when VCC rises above the UVLO (Undervoltage Lockout) threshold VUVLOI and an external program resistor is connected between the PROG pin and ground. When charging, the collector of the external PNP provides the charge current. The PNP's emitter current flows through the ISENSE pin and through the internal 0.24 current sense resistor. This current is close in magnitude, but slightly more than the collector current since it includes the base current. Amplifier A3, along with the P-channel FET, will force the same voltage that appears across the 0.24 resistor to appear across the internal 60 resistor. The scale factor of 250:1 in resistor values will cause the FET's drain current to be 1/ 250 of the charge current and it is this current that flows through the PROG pin. In the constant current mode, amplifier A2 is used to limit the charge current to the value that is programmed by RPROG. The PROG pin current, which is 1/250 of the charge current, develops a voltage across the program resistor. When this voltage reaches 1.5V, amplifier A2 begins diverting current away from the output driver, thus limiting the charge current. This is the constant current mode. The constant charge current is 250 * (1.5V/RPROG). As the battery accepts charge, its voltage rises. When it reaches the preset float voltage of 4.2V, a precisely divided down version of this voltage (2.5V) is compared to the 2.5V internal reference voltage by amplifier A1. If the battery voltage attempts to exceed 4.2V (2.5V at amplifier A1's input) the amplifier will divert current away from the output driver thus maintaining 4.2V on the battery. This is the constant voltage mode. When in the constant voltage mode, the 250:1 current ratio is still valid and the voltage on the PROG pin will indicate the charge current as a proportion of the maximum current set by the current programming resistor. The battery charge current is 250 * (VPROG/RPROG) amps. This feature allows a microcontroller with an ADC to easily monitor charge current and if desired, manually shut down the charger at the appropriate time. When VCC is applied, the charger can be manually shut down by floating the otherwise grounded end of RPROG. An internal 3A current source pulls the PROG pin above the 2.15V threshold of voltage comparator C1 initiating shutdown. For charging NiMH or NiCd batteries, the LTC1734L can function as a constant current source by grounding the BAT pin. This will prevent amplifier A1 from trying to limit charge current and only A2 will control the current. Fault conditions such as overheating of the die or excessive DRIVE pin current are monitored and limited. When input power is removed or manual shutdown is entered, the charger will drain only tiny leakage currents from the battery, thus maximizing battery standby time. With VCC removed the external PNP's base is connected to the battery by the charger. In manual shutdown the base is connected to VCC by the charger. U W U U APPLICATIO S I FOR ATIO Charger Operation Charging begins when an input voltage is present that exceeds the undervoltage lockout threshold (V UVLOI), a Li-Ion battery is connected to the charger output and a program resistor is connected from the PROG pin to ground. During the first portion of the charge cycle, when the battery voltage is below the preset float voltage, the charger is in the constant current mode. As the battery voltage rises and reaches the preset float voltage, the charge current begins to decrease and the constant voltage portion of the charge cycle begins. The charge current will continue to decrease exponentially as the battery approaches a fully charged condition. Should the battery be removed during charging, a fast built-in protection circuit will prevent the BAT pin from rising above 5V, allowing the precision constant voltage circuit time to respond. 1734lf 6 LTC1734L U W U U APPLICATIONS INFORMATION Manual Shutdown Floating the program resistor allows an internal 3A current source (IPROGPU) to pull the PROG pin above the 2.15V shutdown threshold (VMSDT), thus shutting down the charger. In this mode, the LTC1734L continues to draw quiescent current from the supply (ISHDN), but only a negligible leakage current is delivered to the battery (IBMS). Shutdown can also be accomplished by pulling the otherwise grounded end of the program resistor to a voltage greater than 2.25V (VMSDTMax). Charging will cease above 1.5V, but the internal battery voltage resistor divider will draw about 34A from the battery until shutdown is entered. Figure 1 illustrates a microcontroller configuration that can either float the resistor or force it to a voltage. The voltage should be no more than 8V when high and have an impedance to ground of less than 10% of the program resistor value when low to prevent excessive charge current errors. To reduce errors the program resistor value may be adjusted to account for the impedance to ground. The programming resistor will prevent potentially damaging currents if the PROG pin is forced above VCC. Under this condition VCC may float, be loaded down by other circuitry or be shorted to ground. If VCC is not shorted to ground, the current through the resistor will pull VCC up slightly. Another method is to directly switch the PROG pin to a voltage source when shutdown is desired (Caution: pulling the PROG below 1.5V with VCC applied will cause excessive and uncontrolled charge currents). The voltage source must be capable of sourcing the resulting current through the program resistor. This has the advantage of not adding any error to the program resistor during normal operation. The voltage on the PROG pin An NPN transistor or a diode can also be utilized to implement shutdown from a voltage source. These have the advantage of blocking current when the voltage source goes low, thus automatically disconnecting the voltage source for normal charging operation. Using an NPN allows the use of a weak voltage source due to the current gain of the transistor. For an NPN, connect the collector to VCC, the base to the voltage source and the emitter to the PROG pin. For a diode, connect the anode to the voltage source and cathode to the PROG pin. An input high level ranging from 3.3V to VCC should be adequate to enter shutdown while a low level of 0.5V or less should allow for normal charging operation. Use of inexpensive small signal devices such as the 2N3904 or 1N914 is recommended to prevent excessive capacitive loading on the PROG pin (see Stability section). Sleep Mode When the input supply is disconnected, the IC enters the sleep mode. In this mode, the battery drain current (IBSL) is a negligible leakage current, allowing the battery to remain connected to the charger for an extended period of time without discharging the battery. The leakage current is due to the reverse-biased B-E junction of the external PNP transistor. Undervoltage Lockout RPROG OPEN DRAIN OR TOTEM POLE OUTPUT C must be greater than 2.25V (VMSDT(MAX)) to ensure entering shutdown, but no more than 0.3V above VCC to prevent damaging the LTC1734L from excessive PROG pin current. An exception is if VCC is allowed to float with no other circuitry loading VCC down. Then, because the current will be low, it is allowable to have the PROG pin shutdown voltage applied. A three-state logic driver with sufficient pull-up current can be used to perform this function by enabling the high impedance state to charge or enabling the pull-up device to enter shutdown. PROG LTC1734L ADC INPUT 1734 F01 Figure 1. Interfacing with a Microcontroller Undervoltage lockout (UVLO) keeps the charger off until the input voltage exceeds a predetermined threshold level (VUVLOI) that is typically 4.56V. Approximately 150mV of hysteresis is built in to prevent oscillation around the threshold level. In undervoltage lockout, battery drain current is very low (< 1A). 1734lf 7 LTC1734L U U W U APPLICATIONS INFORMATION Programming Constant Current monitoring accuracy can degrade considerably at very low current levels. If current monitoring is desired, a minimum full-scale current of 50mA is recommended. When in the constant current mode, the full-scale charge current is programmed using a single external resistor between the PROG pin and ground. This charge current will be 250 times the current through the program resistor. The program resistor value is selected by dividing the voltage forced across the resistor (1.5V) by the desired resistor current: Different charge currents can be programmed by various means such as by switching in different program resistors as shown in Figures 2 and 3. A voltage DAC connected through a resistor to the PROG pin or a current DAC connected in parallel with a resistor to the PROG pin can also be used to program current (the resistor is required with the IDAC to maintain AC stability as discussed in the Stability section). Another means is to use a PWM output from a microcontroller to duty cycle the charger into and out of shutdown to create an average current (see Manual Shutdown section for interfacing examples). Because chargers are generally slow to respond, it can take up to approximately 300s for the charger to fully settle after a shutdown is deasserted. This delay must be accounted for unless the minimum PWM low duration is about 3ms or more. Shutdown occurs within a few microseconds of a shutdown command. The use of PWM can extend the average current to less than the normal 50mA minimum constant current. RPROG = 375/IBAT The LTC1734L is designed for an absolute maximum current of 210mA. This translates to a maximum PROG pin current of 840A and a minimum program resistor of 1.8k. Because the PROG pin is in a closed-loop signal path, the pole frequency must be kept high enough to maintain adequate AC stability by avoiding excessive capacitance on the pin. See the Stability section for more details. The minimum full-scale current that can be reliably programmed is approximately 10mA, which requires a program resistor of 37.4k. Limiting capacitive loading on the program pin becomes more important when high value program resistors are used. In addition, the current 3 VIN 5V OPTIONAL FILTER 1k PIN 4 0.1F TO 0.5F CHARGE CURRENT MONITOR (UNFILTERED) 4 3k PROG BAT 5 FZT549 IBAT 10F 7.5k Q1 2N7002 CONTROL 1 1 LTC1734L 2 6 GND DRIVE 1F CHARGE CURRENT MONITOR (FILTERED) ISENSE VCC Q2 2N7002 CHARGE CURRENT CONTROL 1 CONTROL 2 0 LOW LOW 50mA LOW HIGH 125mA HIGH LOW 175mA HIGH HIGH SINGLE Li-Ion BATTERY 1734 F02 CONTROL 2 Figure 2. Logic Control Programming of Output Current to 0mA, 50mA, 125mA or 175mA 3 VIN 5V 1F 2 4 3k VCC 1 LTC1734L 6 GND DRIVE FZT549* 5 ILOAD PROG 7.5k Q1 2N7002 ISENSE Q2 2N7002 BAT LOAD 1734 F03 CURRENT CONTROL 1 CONTROL 2 0 LOW LOW 50mA LOW HIGH 125mA HIGH LOW 175mA HIGH HIGH *OBSERVE MAXIMUM TEMPERATURE CONTROL 1 CONTROL 2 Figure 3. Programmable Current Source with Output Current of 0mA, 50mA, 125mA or 175mA 1734lf 8 LTC1734L U W U U APPLICATIONS INFORMATION Monitoring Charge Current The voltage on the PROG pin indicates the charge current as a proportion of the maximum current set by the program resistor. The charge current is equal to 250 * (VPROG/RPROG) amps. This feature allows a microcontroller with an ADC to easily monitor charge current and if desired, manually shut down the charger at the appropriate time. The minimum PROG pin current is about 3A (IPROGPU). Errors in the charge current monitor voltage on the PROG pin and in the full-scale charge current are inversely proportional to battery current and can be statistically approximated as follows: One Sigma Error(%) 1 + 0.08/IBAT(A) Dynamic loads on the battery will cause transients to appear on the PROG pin. Should they cause excessive errors in charge current monitoring, a simple RC filter as shown in Figure 2 can be used to filter the transients. The filter will also quiet the PROG pin to help prevent momentary entry into the manual shutdown mode. Because the PROG pin is in a closed-loop signal path the pole frequency must be kept high enough to maintain adequate AC stability. This means that the maximum resistance and capacitance presented to the PROG pin must be limited. See the Stability section for more details. Constant Current Source The LTC1734L can be used as a constant current source by disabling the voltage control loop as shown in Figure 3. This is done by pulling the BAT pin below the preset float voltage of 4.2V by grounding the BAT pin. The program resistor will determine the output current. The output current range can be between approximately 10mA and 180mA, depending on the maximum power rating of the external PNP pass transistor. External PNP Transistor The external PNP pass transistor must have adequate beta, low saturation voltage and sufficient power dissipation capability (including any heat sinking, if required). To provide 180mA of charge current with the minimum available base drive of approximately 20mA requires a PNP beta greater than 9. With low supply voltages, the PNP saturation voltage (VCESAT) becomes important. The VCESAT must be less than the minimum supply voltage minus the maximum voltage drop across the internal sense resistor and bond wires (0.3) and battery float voltage. If the PNP transistor can not achieve the low saturation voltage required, base current will dramatically increase. This is to be avoided for a number of reasons: output drive may reach current limit resulting in the charger's characteristics to go out of specifications, excessive power dissipation may force the IC into thermal shutdown, or the battery could become discharged because some of the current from the DRIVE pin could be pulled from the battery through the forward biased collector base junction. For example, to program a charge current of 100mA with a minimum supply voltage of 4.75V, the minimum operating VCE is: VCE(MIN)(V) = 4.75 - (0.1)(0.3) - 4.2 = 0.52V The actual battery charge current (IBAT) is slightly less than the expected charge current because the charger senses the emitter current and the battery charge current will be reduced by the base current. In terms of (IC/IB), IBAT can be calculated as follows: IBAT(A) = 250 * IPROG[/( + 1)] If = 50, then IBAT is 2% low. If desired, the 2% loss can be compensated for by increasing IPROG by 2%. Another important factor to consider when choosing the PNP pass transistor is the power handling capability. The transistor's data sheet will usually give the maximum rated power dissipation at a given ambient temperature with a power derating for elevated temperature operation. The maximum power dissipation of the PNP when charging is: PD(MAX)(W) = IBAT (VDD(MAX) - VBAT(MIN)) VDD(MAX) is the maximum supply voltage and VBAT(MIN) is the minimum battery voltage when discharged. 1734lf 9 LTC1734L U U W U APPLICATIONS INFORMATION Table 1. PNP Pass Transistor Selection Guide Maximum PD (W) Mounted on Board at TA = 25C Package Style 0.2 SC-70 0.2 SC-70 0.5 SOT-23 0.625 1 ZETEX Part Number ROHM Part Number Comments UMT4403 Smallest Size UMT2907A Smallest Size FMMT549 Low VCESAT SOT-23 FMMT720 Very Low VCESAT, High Beta SOT-89 FCX589 or BCX69 1.1 SOT-23-6 ZXT10P12DE6 1 to 2 SOT-89 FCX717 Very Low VCESAT, High Beta Very Low VCESAT, High Beta, Small 2 SOT-223 FZT589 Low VCESAT 2 SOT-223 BCP69 or FZT549 0.75 FTR 2SB822 Low VCESAT 1 ATV 2SB1443 Low VCESAT 2 SOT-89 2SA1797 Low VCESAT Once the maximum power dissipation and VCE(MIN) are known, Table 1 can be used as a guide in selecting a suitable PNP transistor. In the table, very low VCESAT is less than 0.25V, low VCESAT is 0.25V to 0.5V and the others are 0.5V to 0.8V all depending on the current required. See the manufacturer's data sheet for details. All of the PNP transistors are rated to carry at least 1A continuously as long as the power dissipation is within limits. The Stability section addresses caution in the use of high beta PNPs. Should overheating of the PNP transistor be a concern, protection can be achieved with a positive temperature coefficient (PTC) thermistor, wired in series with the current programming resistor and thermally coupled to the transistor. The PRF chip series from Murata has a steep resistance increase at temperature thresholds from 85C to 145C making it behave somewhat like a thermostat switch. For example, the model PRF18BA471QB1RB thermistor is 470 at 25C, but abruptly increase its resistance to 4.7k at 125C. Below 125C, the device exhibits a small negative TC. The 470 thermistor can be added in series with a 1.6k resistor to form the current programming resistor for a 180mA charger. Should the thermistor reach 125C, the charge current will drop to 60mA and inhibit any further increase in temperature. Stability The LTC1734L contains two control loops: constant voltage and constant current. To maintain good AC stability in the constant voltage mode, a capacitor of at least 4.7F is usually required from BAT to ground. The battery and interconnecting wires appear inductive at high frequencies, and since these are in the feedback loop, this capacitance may be necessary to compensate for the inductance. This capacitor need not exceed 100F and its ESR can range from near zero to several ohms depending on the inductance to be compensated. In general, compensation is optimal with a capacitance of 4.7F to 22F and an ESR of 0.5 to 1.5. Using high beta PNP transistors (>300) and very low ESR output capacitors (especially ceramic) reduces the phase margin, possibly resulting in oscillation. Also, using high value capacitors with very low ESRs will reduce the phase margin. Adding a resistor of 0.5 to 1.5 in series with the capacitor will restore the phase margin. In the constant current mode, the PROG pin is in the feedback loop, not the battery. Because of this, capacitance on this pin must be limited. Locating the program resistor near the PROG pin and isolating the charge current monitoring circuitry (if used) from the PROG pin with a 1k to 10k resistor may be necessary if the capacitance is greater than that given by the following equation: CMAX(pF) = 400k RPROG 1734lf 10 LTC1734L U U W U APPLICATIONS INFORMATION Higher charge currents require lower program resistor values which can tolerate more capacitive loading on the PROG pin. Maximum capacitance can be as high as 50pF for a charge current of 50mA (RPROG = 7.5k). Figure 4 is a simple test circuit for checking stability in both the constant current and constant voltage modes. With input power applied and a near fully charged battery connected to the charger, driving the PROG pin with a pulse generator will cycle the charger in and out of the manual shutdown mode. Referring to Figure 5, after a short delay, the charger will enter the constant current mode first, then if the battery voltage is near the programmed voltage of 4.2V, the constant voltage mode will begin. The resulting waveform on the PROG pin is an indication of stability. The double exposure photo in Figure 5 shows the effects of capacitance on the program pin. The middle waveform is typical while the lower waveform indicates excessive program pin capacitance resulting in constant current mode instability. Although not common, ringing on the constant voltage portion of the waveform is an indication * VIN VCC LTC1734L 1734 F06 *DRAIN-BULK DIODE OF FET Figure 6. Low Loss Reverse Voltage Protection VCC Bypass Capacitor 2V Internal Protection PROG RPROG 3k BAT + Li-Ion* LTC1734L 20 TO 200 2.5V 0V f = 1kHz 1734 F04 *FULLY CHARGED CELL Figure 4. Setup for AC Stability Testing 5V 1V 0V 2V PROG PIN (200pF ON PIN) In some applications, protection from reverse voltage on VCC is desired. If the supply voltage is high enough, a series blocking diode can be used. In other cases, where the voltage drop must be kept low, a P-channel FET as shown in Figure 6 can be used. 0V TO SCOPE PROG PIN (20pF ON PIN) Reverse Input Voltage Protection Many types of capacitors with values ranging from 1F to 10F located close to the LTC1734L will provide adequate input bypassing. However, caution must be exercised when using multilayer ceramic capacitors. Because of the self resonant and high Q characteristics of some types of ceramic capacitors, high voltage transients can be generated under some start-up conditions, such as connecting the charger input to a hot power source. To prevent these transients from exceeding the absolute maximum voltage rating, several ohms of resistance can be added in series with the ceramic input capacitor. 10k PULSE GENERATOR of instability due to any combination of extremely low ESR values, high capacitance values of the output capacitor or very high PNP transistor beta. To minimize the effect of the scope probe capacitance, a 10k resistor is used to isolate the probe from the program pin. Also, an adjustable load resistor or current sink can be used to quickly alter the charge current when a fully charged battery is used. 1V 0V SHUT DELAY DOWN CONSTANT CURRENT CONSTANT VOLTAGE HORIZONTAL SCALE: 100s/DIV Figure 5. Stability Waveforms Internal protection is provided to prevent excessive DRIVE pin currents (IDSHRT) and excessive self-heating of the LTC1734L during a fault condition. The faults can be generated from a shorted DRIVE pin or from excessive DRIVE pin current to the base of the external PNP transistor when it's in deep saturation from a very low VCE. This protection is not designed to prevent overheating of the external pass transistor. Indirectly though, selfheating of the PNP thermally conducting to the LTC1734L 1734lf Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC1734L U U W U APPLICATIONS INFORMATION and resulting in the IC's junction temperature to rise above 150C, thus cutting off the base current to the PNP transistor. This action will limit the transistor junction temperature to a temperature well above 150C. The temperature depends on how well the IC and PNP are thermally connected and on the transistor's JA. See the External PNP Transistor section for information on protecting the transistor from overheating. U PACKAGE DESCRIPTIO S6 Package 6-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1636) 0.62 MAX 2.90 BSC (NOTE 4) 0.95 REF 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.30 - 0.45 6 PLCS (NOTE 3) 0.95 BSC 0.80 - 0.90 NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) 1.90 BSC S6 TSOT-23 0302 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT(R)1510-5 500kHz Constant-Current/Constant-Voltage Battery Charger Up to 1A Charge Current for Li-Ion, NiCd, NiMH or Lead-Acid Batteries LT1571-1/LT1571-2 200kHz/500kHz Constant-Current/Constant-Voltage Battery LT1571-5 Charger Family Up to 1.5A Charge Current for 1-, 2- or Multiple Cell Li-Ion Batteries, Preset and Adjustable Battery Voltages, C/10 Charge Detection LTC1729 Li-Ion Battery Charger Termination Controller Can be Used with LTC Battery Chargers to Provide Charge Termination, Preset Voltages, C/10 Charge Detection and Timer Functions LTC1730 Li-Ion Battery Pulse Charger Minimizes Heat Dissipation, No Blocking Diode Required, Limits Maximum Current for Safety LTC1731 Linear Constant-Current/Constant-Voltage Charger Controller Simple Charger Uses External FET. Features Preset Voltages, C/10 Charge Detection and Programmable Timer LTC1733 Standalone, Monolithic Linear Li-Ion Battery Charger C/10 Charge Detection and Programmable Timer, 1.25A, 4.2V Single-Cell, Thermal Feedback Loop LTC1734 200mA to 700mA Li-Ion Linear Charger in ThinSot Pin Compatible with the LTC1734L, Higher Charge Current LT1769 200kHz Constant-Current/Constant-Voltage Battery Charger Up to 2A Charge Current for Li-Ion, NiCd, NiMH or Lead-Acid Batteries with Input Current Limit 1734lf 12 Linear Technology Corporation LT/TP 0802 2K * PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2001