Original Creation Date: 06/27/95
Last Update Date: 02/07/01
Last Major Revision Date: 02/02/01
MJLM117-H REV 1A1 MICROCIRCUIT DATA SHEET
POSITIVE THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR
General Description
The LM117 adjustable 3-terminal positive voltage regulator is capable of supplying in
excess of 0.5A over a 1.2V to 37V output range. It is exceptionally easy to use and
requires only two external resistors to set the output voltage. Further, both line and
load regulation are better than standard fixed regulators.
In addition to higher performance than fixed regulators, the LM117 offers full overload
protection available only in IC's. Included on the chip are current limit, thermal
overload protection and safe area protection. All overload protection circuitry remains
fully functional even if the adjustment terminal is disconnected.
Normally, no capacitors are needed unless the device is situated more than 6 inches from
the input filter capacitors in which case an input bypass is needed. An optional output
capacitor can be added to improve transient response. The adjustment terminal can be
bypassed to achieve very high ripple rejection ratios which are difficult to achieve with
standard 3-terminal regulators.
Besides replacing fixed regulators, the LM117 is useful in a wide variety of other
applications. Since the regulator is "Floating" and sees only the input-to-output
differential voltage, supplies of several hundred volts can be regulated as long as the
maximum input to output differential is not exceeded, (i.e., avoid short-circuiting the
output).
Also, it makes an especially simple adjustable switching regulator, a programmable output
regulator, or by connecting a fixed resistor between the adjustment pin and output, the
LM117 can be used as a precision current regulator. Supplies with electronic shutdown can
be achieved by clamping the adjustment terminal to ground which programs the output to
1.2V where most loads draw little current.
NS Part Numbers
JL117BXA
JL117SXA
Industry Part Number
LM117H
Prime Die
LM117H
Controlling Document
38510/11703,AMEND.3 Cir.A REV A
Processing
MIL-STD-883, Method 5004
Quality Conformance Inspection
MIL-STD-883, Method 5005
Subgrp Description Temp ( C)
o
1 Static tests at +25
2 Static tests at +125
3 Static tests at -55
4 Dynamic tests at +25
5 Dynamic tests at +125
6 Dynamic tests at -55
7 Functional tests at +25
8A Functional tests at +125
8B Functional tests at -55
9 Switching tests at +25
10 Switching tests at +125
11 Switching tests at -55
1
MICROCIRCUIT DATA SHEET
MJLM117-H REV 1A1
Features
- Guaranteed 0.5A output current
- Adjustable output down to 1.2V
- Current limit constant with temperature
- 80 dB ripple rejection
- Output is short-circuit protected
2
MICROCIRCUIT DATA SHEET
MJLM117-H REV 1A1
(Absolute Maximum Ratings)
(Note 1)
Power Dissipation Internally Limited
Input-Output Voltage Differential +40V, -0.3V
Maximum Junction Temperature 150 C
Storage Temperature Range -65 C to +150 C
Lead Temperature (Soldering, 10 seconds) 300 C
Thermal Resistance
ThetaJA 186 C/W (Still Air) 64 C/W (500LF/Min Air flow)
21 C/WThetaJC
ESD Tolerance
(Note 3) 3000V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Operating ratings indicate conditions for which the device is functional, but do not
guarantee specific performance limits. For guaranteed specifications and test
conditions, see the Electrical Characteristics. The guaranteed specifications apply
only for the test conditions listed. Some performance characteristics may degrade
when the device is not operated under the listed test conditions.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is
dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to
ambient thermal resistance), and TA (ambient temperature). The maximum allowable
power dissipation at any temperature is Pdmax (Tjmax - TA)/ThetaJA or the number
given in the Absolute Maximum Rating, whichever is lower.
Note 3: Human body model, 1.5K Ohms in series with 100pF.
Recommended Operating Conditions
Operating Temperature Range -55 C < TA < +125 C
3
MJLM117-H REV 1A1 MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS
SYMBOL PARAMETER CONDITIONS NOTES PIN-
NAME MIN MAX UNIT SUB-
GROUPS
Vout Output Voltage Vin = 4.25V, Il = -5mA 1.2 1.3 V 1, 2,
3
Vin = 4.25V, Il = -500mA 1.2 1.3 V 1, 2,
3
Vin = 41.25V, Il = -5mA 1.2 1.3 V 1, 2,
3
Vin = 41.25V, Il = -50mA 1.2 1.3 V 1, 2,
3
Vrline Line Regulation 4.25V < Vin < 41.25V, Il = -5mA -9 9 mV 1
-23 23 mV 2, 3
Vrload Load Regulation Vin = 6.25V, -500mA < Il < -5mA -12 12 mV 1, 2,
3
Vin = 41.25V, -50mA < Il < -5mA -12 12 mV 1, 2,
3
Vrth Thermal
Regulation Vin = 14.6V, Il = -500mA -12 12 mV 1
Iadj Adjust Pin
Current Vin = 4.25V, Il = -5mA -100 -15 uA 1, 2,
3
Vin = 41.25V, Il = -5mA -100 -15 uA 1, 2,
3
Delta
Iadj/Line Adjust Pin
Current Change 4.25V < Vin < 41.25V, Il = -5mA -5 5 uA 1, 2,
3
Delta
Iadj/Load Adjust Pin
Current Change Vin = 6.25V, -500mA < Il < -5mA -5 5 uA 1, 2,
3
Iq Minimum Load
Current Vin = 4.25V, Forced Vout = 1.4V -3 -0.5 mA 1, 2,
3
Vin = 14.25V, Forced Vout = 1.4V -3 -0.5 mA 1, 2,
3
Vin = 41.25V, Forced Vout = 1.4V -5 -1 mA 1, 2,
3
Ios Output Short
Circuit Current Vin = 4.25V -1.8 -0.5 A 1, 2,
3
Vin = 40V -0.5 -0.05 A 1, 2,
3
Vout
(Recov) Output Voltage
Recovery Vin = 4.25V, Rl = 2.5 Ohms, Cl = 20uF 1.2 1.3 V 1, 2,
3
Vin = 40V, Rl = 250 Ohms 1.2 1.3 V 1, 2,
3
Vout Output Voltage
Recovery Vin = 6.25V, Il = -5mA 1 1.2 1.3 V 2
4
MJLM117-H REV 1A1 MICROCIRCUIT DATA SHEET
Electrical Characteristics
DC PARAMETERS(Continued)
SYMBOL PARAMETER CONDITIONS NOTES PIN-
NAME MIN MAX UNIT SUB-
GROUPS
Vstart Voltage Start-Up Vin = 4.25V, Rl = 2.5 Ohms, Cl = 20uF,
Il = -500mA 1.2 1.3 V 1, 2,
3
AC PARAMETERS
Delta
Vin/Delta
Vout
Ripple Rejection Vin = 6.25V, ei = 1Vrms at f = 2400Hz,
Il = -125mA 65 dB 4
Vno Output Noise
Voltage Vin = 6.25V, Il = -50mA 120 uVrms 7
Delta
Vout/Delta
Vin
Line Transient
Response Vin = 6.25V, Delta Vin = 3V,
Il = -10mA 6 mV/V 7
Delta
Vout/
Delta Il
Load Transient
Response Vin = 6.25V, Delta Il = -200mA,
Il = -50mA 0.6 mV/mA 7
DC PARAMETERS: DRIFT VALUES
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: "Delta calculations performed on JAN S and QMLV devices at group B, subgroup 5 ONLY."
Vout Output Voltage Vin = 4.25V, Il = -5mA -0.01 0.01 V 1
Vin = 4.25V, Il = -500mA -0.01 0.01 V 1
Vin = 41.25V, Il = -5mA -0.01 0.01 V 1
Vin = 41.25V, Il = -50mA -0.01 0.01 V 1
Vrline Line Regulation 4.25V < Vin < 41.25V, Il = -5mA -4 4 mV 1
Iadj Adjust Pin
Current Vin = 4.25V, Il = -5mA -10 10 uA 1
Vin = 41.25V, Il = -5mA -10 10 uA 1
Note 1: Tested at TA = 125 C, correlated to TA = 150 C.
5
MICROCIRCUIT DATA SHEET
MJLM117-H REV 1A1
Graphics and Diagrams
GRAPHICS# DESCRIPTION
9784HRB2 METAL CAN (H), TO-39, 3LD, .200 DIA P.C. (B/I CKT)
H03ARD METAL CAN (H), TO-39, 3LD, .200 DIA P.C. (P/P DWG)
P000174A METAL CAN (H), TO-39, 3LD, .200 DIA P.C. (PINOUT)
See attached graphics following this page.
6
N
 
 
   








MICROCIRCUIT DATA SHEET
MJLM117-H REV 1A1
Revision History
Rev ECN # Rel Date Originator Changes
0C1 M0003587 02/07/01 Rose Malone Updated MDS: MJLM117-H, Rev. 0B0 to MJLM117-H, Rev.
0C1. Corrected typo on Vrline, Delta Iadj/Line, Vout.
Changed Iil to Il on all parameters. Updated B/I ckt
graphic and Added Pinout.
1A1 M0003785 02/07/01 Rose Malone Update MDS: MJLM117-H, Rev. 0C1 to MJLM117-H, Rev.
1A1. Removed in Electricals from Drift Values Section
Parameter Vout(Recov)
7