ByteBlaster II Download Cable User Guide 101 Innovation Drive San Jose, CA 95134 www.altera.com Software Version: Document Version: Document Date: 8.0 1.4 July 2008 Copyright (c) 2008 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. P25-36288-00 UG-BBII81204-1.4 Contents Chapter 1. Setting Up the ByteBlaster II Download Cable Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Software Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Installing the Driver on a Windows System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Installing the Driver on a Linux System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Setting Up the ByteBlaster II Hardware in the Quartus II Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Chapter 2. ByteBlaster II Specifications Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 ByteBlaster II Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Voltage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Cable-to-Board Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 ByteBlaster II 25-Pin Header Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 ByteBlaster II 10-Pin Header Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Circuit Board Header Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Statement of China-RoHS Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Chapter Info. Additional Information Referenced Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Contact Altera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (c) July 2008 Altera Corporation Info-1 Info-2 Info-3 Info-3 ByteBlaster II Download Cable User Guide 2 ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation List of Figures 3 List of Figures Figure 1-1: The ByteBlaster II Download Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 1-2: Hardware Setup Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 2-1: ByteBlaster II Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 2-2: ByteBlaster II 10-Pin Female Plug Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 2-3: 10-Pin Male Header Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (c) July 2008 Altera Corporation 1-2 1-6 2-2 2-3 2-4 ByteBlaster II Download Cable User Guide 4 ByteBlaster II Download Cable User Guide List of Figures (c) July 2008 Altera Corporation List of Tables 5 List of Tables Table 1-1: Programming Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Table 2-1: ByteBlaster II VCC(TRGT) Pin Voltage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Table 2-2: ByteBlaster II 25-Pin Header Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Table 2-3: ByteBlaster II Female Plug Signal Names and Programming Modes . . . . . . . . . . . . . . . . . . . . . 2-3 Table 2-4: ByteBlaster II Cable Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Table 2-5: ByteBlaster II Cable Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Table 2-6: ByteBlaster II Cable DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Table 2-7: Table of Hazardous Substances' Name and Concentration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Table Info-1: Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info-2 Table Info-2: How to Contact Altera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info-3 Table Info-3: Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info-3 (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide 6 ByteBlaster II Download Cable User Guide List of Tables (c) July 2008 Altera Corporation 1. Setting Up the ByteBlaster II Download Cable Introduction The ByteBlasterTM II download cable allows you to program and configure Altera(R) devices. This cable drives configuration data from a standard parallel printer port on your PC to the device on the PCB. Because design changes are downloaded directly to the device, prototyping is easy and you can accomplish multiple design iterations in quick succession. Supported Devices You can use the ByteBlaster II download cable to download configuration data to the following Altera devices: Stratix(R) series FPGAs Cyclone(R) series FPGAs MAX(R) series CPLDs ArriaTM GX series FPGAs APEXTM series FPGAs ACEX(R) 1K FPGAs MercuryTM FPGAs FLEX 10K(R) series FPGAs ExcaliburTM FPGAs You can perform in-system programming of the following devices: Advanced configuration devices including EPC2, EPC4, EPC8, and EPC16 devices. Serial configuration devices including EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128 devices. In addition, you can perform SignalTap(R) II logic analysis. The ByteBlaster II download cable supports target systems using 5.0-V TTL, 3.3-V LVTTL/LVCMOS, and single-ended I/O standards from 1.5 V to 3.3 V. Power Requirements The ByteBlaster II download cable requires between 1.5 V and 5.0 V from the target circuit board. The ByteBlaster II cable can be used in 1.8-V, 2.5-V, 3.3-V, and 5.0-V systems. The ByteBlaster II VCC(TRGT) pin must be connected to the appropriate voltage for the device that is being programmed. The pull-up resistors on the target circuit board for the configuration/programming signals must be connected to the same power supply as the ByteBlaster II VCC(TRGT). (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide 1-2 Chapter 1: Setting Up the ByteBlaster II Download Cable Hardware Setup Software Requirements The ByteBlaster II download cable is available for Windows 2000, Windows NT, Windows XP, and Linux. Use the Quartus(R) II software version 4.0 or later to configure your device. The ByteBlaster II download cable also supports the following tools: Quartus II Programmer (for programming and configuration), which you can run within the Quartus II software or as a standalone version Quartus II SignalTap II Embedded Logic Analyzer (for logic analysis), which you can run within the Quartus II software or as a standalone version Nios(R) II IDE (for software downloading and debugging) Nios II IDE Flash Programmer (for programming Flash devices) Hardware Setup This section describes how to install and set up the ByteBlaster II download cable for device configuration and programming. 1 For plug and header dimensions, pin names, and operating conditions, refer to Chapter 2, ByteBlaster II Specifications chapter. Connect your ByteBlaster II download cable to the circuit board as instructed below: 1. Disconnect the power cable from the circuit board. 2. Connect the ByteBlaster II cable to a parallel port on your PC. 3. Connect the ByteBlaster II download cable to the 10-pin header on the device board. Figure 1-1 shows the ByteBlaster II download cable and the circuit board connector. Figure 1-1. The ByteBlaster II Download Cable Computer Parallel Port ByteBlaster II 10-pin Female Plug (R) B y te B la s te r TM II ByteBlaster II Download Cable 4. Connect the power cable to reapply power to the circuit board. ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup 1 1-3 If the Found New Hardware wizard prompts you to install a new hardware driver, close the wizard and install the hardware driver using the instructions provided in "Installing the Driver on a Windows System" or "Installing the Driver on a Linux System", depending on your system. Software Setup This section describes the following topics: "Installing the Driver on a Windows System" on page 1-3 "Installing the Driver on a Linux System" on page 1-4 "Setting Up the ByteBlaster II Hardware in the Quartus II Software" on page 1-5 Installing the Driver on a Windows System This section describes how to install the ByteBlaster II driver on a Windows system. Before you begin the installation, verify the ByteBlaster II driver is located in your directory: \<Quartus II system directory>\drivers\win2000\win2000.inf Installing the Driver for Windows 2000 and Windows XP To install the driver for Windows 2000 or Windows XP, perform the following steps: 1. For Windows 2000, choose Settings > Control Panel (Windows Start menu). For Windows XP, choose Control Panel (Windows Start menu). 2. Click Switch to Classic View if necessary (Control Panel window). 3. Double-click the Add Hardware icon to start the Add Hardware wizard and click Next to continue. 4. Select Yes, I have already connected the hardware and click Next. 5. Select Add a new hardware device from the Installed hardware list, and click Next to continue. 6. Select Install from a list or specified location (Advanced) and click Next to continue. 1 Depending on your system, the wording of this option may vary slightly. 7. Select Sound, video and game controllers, and click Next to continue. 8. Select Have Disk and browse to the location of the driver on your system. The default location is the \<Quartus II system directory>\ drivers\win2000 directory. 9. Select win2000.inf and click Open to continue. 10. Click OK to install the selected driver. 11. Click Continue Anyway when the Software Installation warning appears. 12. Select Altera ByteBlaster and click Next to continue. 13. Click Next to install the driver. (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide 1-4 Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup 14. Click Continue Anyway when the Hardware Installation warning appears. 15. Click Finish in the Completing the Add Hardware Wizard window. Reboot your system. Installing the Driver for Windows NT To install the driver for Windows NT, perform the following steps: 1. For Windows NT, choose Settings > Control Panel (Windows Start menu). 2. Double-click the Multimedia icon in the Control Panel window. 3. Click the Devices tab and click the Add button. 4. Click Unlisted or Updated Driver from the List of Drivers list box and click OK. 5. Browse to the location of the driver on your system. The default location is the \<Quartus II system directory>\ drivers\win2000 directory. Click OK. 6. Select Altera ByteBlaster or Altera ByteBlaster II in the Add Unlisted or Updated Driver window and click OK. Reboot your system. Installing the Driver on a Linux System The Altera ByteBlaster kernel driver is required for Linux workstations running Red Hat Linux version 7.3 or 8.0 or Red Hat Enterprise Linux version 3.0 or later that use the ByteBlaster II download cable. You must install and compile the Altera ByteBlaster kernel driver separately from the Quartus II software. To compile the Altera ByteBlaster kernel driver, you must have the following Red Hat Package Manager (RPM) packages, which are available from the Red Hat website at www.redhat.com: .gcc-2.96-81 .make-3.79.1-5 .binutils-2.10.91.0.2-3 kernel-headers (RPM version must correspond to kernel version) To verify that an RPM is installed, use the rpm -q <name> command. For example, rpm -q gcc verifies that the gcc RPM is installed. 1 You do not need to install the ByteBlaster II download cable before installing the Altera ByteBlaster kernel driver. 1 You must have superuser or "root" privileges to install this driver. To install the driver for Linux, perform the following steps: 1. Decompress the byteblaster.tar.gz file by typing the following command at the command prompt: tar -xzvf byteblaster.tar.gz r 2. Access the new directory by typing the following command at the command prompt: cd byteblaster r ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup 1-5 3. Run the configure install script by typing the following command at the command prompt: ./configure r 4. Compile the Altera ByteBlaster kernel driver by typing the following command at the command prompt: make r 5. Become root and compile the Altera ByteBlaster kernel driver module and device nodes by typing the following command at the command prompt: make install r 6. To install the Altera ByteBlaster kernel driver, type the following command at the command prompt: jtagconfig --add byteblaster2 /dev/byteblaster0 r 7. To determine whether the ByteBlaster II download cable and the Altera ByteBlaster kernel driver are installed correctly, display a list of available devices by typing the following command at the command prompt: jtagconfig r You should see a list of devices on your JTAG chain, including the ByteBlaster II download cable. Setting Up the ByteBlaster II Hardware in the Quartus II Software To set up the ByteBlaster II hardware in the Quartus II software, perform the following steps: 1. Start the Quartus II software. 2. On the Tools menu, click Programmer. 3. Click Hardware Setup. The Hardware Settings tab of the Hardware Setup dialog box appears. 4. In the Currently selected hardware list, select ByteBlasterII [LPT1]. 5. Click Add Hardware. The Add Hardware dialog box appears. Select ByteBlaster MV or ByteBlaster II and click OK. 6. ByteBlasterII is now visible in the Available hardware items list of the Hardware Setup dialog box, as shown in Figure 1-2. (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide 1-6 Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup Figure 1-2. Hardware Setup Dialog Box 7. Click Close to close the Hardware Setup dialog box. 8. In the Mode list, select the desired mode (Programmer window). Table 1-1 describes each mode. 1 The ByteBlaster II supports the Joint Test Action Group (JTAG), Passive Serial Programming, and Active Serial modes. Table 1-1. Programming Modes Mode Mode Description Joint Test Action Group (JTAG) Programs or configures all Altera devices supported by the Quartus II software, excluding FLEX 6000 and EPCS serial configuration devices. In-Socket Programming Not supported by the ByteBlaster II cable. Passive Serial Programming Configures all Altera devices supported by the Quartus II software, excluding MAX 3000, MAX 7000, MAX II, and EPCS serial configuration devices. Active Serial Programming Programs a single EPCS1, EPCS4, EPCS16, EPCS64 or EPCS128 serial configuration device. f For details about the Quartus II Programmer, refer to the Quartus II Programmer chapter in volume 1 of the Quartus II Handbook. f For details about programming devices and creating secondary programming files, refer to the Programming & Configuration chapter of the Introduction to the Quartus II Software manual. f For more information, refer to the Programming module of the Quartus II software online tutorial and the following topics in the Quartus II Help: Changing the Hardware Setup Programmer Introduction Overview: Working with Chain Description Files ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup (c) July 2008 Altera Corporation 1-7 Overview: Converting Programming Files ByteBlaster II Download Cable User Guide 1-8 ByteBlaster II Download Cable User Guide Chapter 1: Setting Up the ByteBlaster II Download Cable Software Setup (c) July 2008 Altera Corporation 2. ByteBlaster II Specifications Overview This chapter provides comprehensive information about the ByteBlasterTM II download cable, including the following: ByteBlaster II connections Voltage requirements Cable-to-board connection ByteBlaster II 25-pin header connection ByteBlaster II 10-pin header connection Circuit board header connection Operating conditions ByteBlaster II Connections The ByteBlaster II cable has a 25-pin male header parallel printer plug that connects to the PC, and a 10-pin female plug that connects to the circuit board. Data is downloaded from the parallel printer port on the PC through the ByteBlaster II cable to the circuit board. Voltage Requirements The ByteBlaster II VCC(TRGT) pin must be connected to a specific voltage for the device that is being programmed. Connect pull-up resistors to the same power supply as the ByteBlaster II VCC(TRGT). Refer to Table 2-1 for voltage requirements for specific device families. Table 2-1. ByteBlaster II VCC(TRGT) Pin Voltage Requirements (Part 1 of 2) Device Family ByteBlaster II VCC Voltage Required (R) MAX II devices As specified by VCCIO of Bank 1 MAX 7000S devices 5V MAX 7000AE and MAX 3000A devices 3.3 V MAX 7000B device 2.5 V Stratix(R) As specified by VCCPGM or VCCPD III and Stratix IV devices (R) Cyclone III devices As specified by VCCA or VCCIO TM Stratix II, Stratix, Stratix II GX, Stratix GX, and Arria GX devices Cyclone II, Cyclone, APEXTM II, APEX 20K, and (R) MercuryTM devices As specified by VCCSEL As specified by VCCIO FLEX 10K , FLEX 8000, and FLEX 6000 devices 5V FLEX 10KE devices 2.5 V FLEX 10KA and FLEX 6000A devices 3.3 V EPC2 5 V or 3.3 V (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide 2-2 Chapter 2: ByteBlaster II Specifications ByteBlaster II Connections Table 2-1. ByteBlaster II VCC(TRGT) Pin Voltage Requirements (Part 2 of 2) EPC4, EPC8, and EPC16 devices 3.3 V EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128 devices 3.3 V Cable-to-Board Connection The ByteBlaster II cable has a standard parallel printer plug that connects to the PC. Figure 2-1 shows a block diagram of the ByteBlaster II download cable. Figure 2-1. ByteBlaster II Block Diagram VCC VCC 4 15 14 2 1 TRI 3 5 TRI 4 8 TRI 5 6 TRI 8 9 TRI 6 10 11 3 13 7 18 to 25 2, 10 Series Resistors for Signal Quality and Parallel Port Protection (Typically 100 ) GND GND ByteBlaster II 25-Pin Header Connection The 25-pin male header connects to a parallel port with a standard parallel cable. Table 2-2 identifies the plug pin names and the corresponding programming modes. Table 2-2. ByteBlaster II 25-Pin Header Pin-Outs (Part 1 of 2) AS Mode Pin Signal Name Description PS Mode Signal Name Description JTAG Mode Signal Name Description 2 DCLK Clock signal DCLK Clock signal TCK Clock signal 3 nCONFIG Configuration control nCONFIG Configuration control TMS JTAG state machine control 4 nCS Serial configuration device chip select ByteBlaster II Download Cable User Guide -- No connect -- No connect (c) July 2008 Altera Corporation Chapter 2: ByteBlaster II Specifications ByteBlaster II Connections 2-3 Table 2-2. ByteBlaster II 25-Pin Header Pin-Outs (Part 2 of 2) 5 nCE Cyclone chip enable 8 ASDI Active serial data in DATA0 Data to device TDI Data to device 11 CONF_DONE Configuration done CONF_DONE Configuration done TDO Data from device 13 DATAOUT Active serial data out nSTATUS Signal status 15 nVCC Detect 18 to 25 -- No connect -- No connect -- nVCC Detect Signal ground GND No connect -- -- nVCC Detect Signal ground GND -- Signal ground GND ByteBlaster II 10-Pin Header Connection The 10-pin female plug connects to a 10-pin male header on the circuit board. Figure 2-2 shows the dimensions of the female plug. Figure 2-2. ByteBlaster II 10-Pin Female Plug Dimensions 0.425 Typ. 10 8 6 4 2 9 7 5 3 1 0.250 Typ. 0.100 Sq. 0.025 Sq. 0.700 Typ. Dimensions are shown in inches. Spacing between pin centers is 0.1 inches. Table 2-3 identifies the 10-pin female plug signal names and the corresponding programming mode. Table 2-3. ByteBlaster II Female Plug Signal Names and Programming Modes AS Mode Pin 1 Signal Name DCLK Description Clock signal (Part 1 of 2) PS Mode Signal Name Description Clock signal DCLK JTAG Mode Signal Name Description Clock signal TCK 2 GND Signal ground GND Signal ground GND Signal ground 3 CONF_DONE Configuration done CONF_DONE Configuration done TDO Data from device 4 VCC(TRGT) Target power supply VCC(TRGT) Target power supply VCC(TRGT) Target power supply 5 nCONFIG Configuration control nCONFIG Configuration control TMS JTAG state machine control 6 nCE Cyclone chip enable 7 DATAOUT Active serial data out 8 nCS Serial configuration device chip select (c) July 2008 Altera Corporation -- nSTATUS -- No connect -- No connect Configuration status -- No connect No connect -- No connect ByteBlaster II Download Cable User Guide 2-4 Chapter 2: ByteBlaster II Specifications Operating Conditions Table 2-3. ByteBlaster II Female Plug Signal Names and Programming Modes (Part 2 of 2) 9 ASDI Active serial data in DATA0 Data to device TDI Data to device 10 GND Signal ground GND Signal ground GND Signal ground 1 The circuit board must supply VCC(TRGT) and ground to the ByteBlaster II cable for the I/O drivers. Circuit Board Header Connection The circuit board's 10-pin male header has two rows of five pins connected to the device's programming or configuration pins. Figure 2-3 shows the dimensions of a typical 10-pin male header. 1 Although a 10-pin surface mount header can be used for the JTAG, AS or PS download cable, Altera recommends using a through-hole connector due to the repeated insertion and removal force needed. Figure 2-3. 10-Pin Male Header Dimensions Top View Side View 0.100 0.025 Sq. 0.100 0.235 Dimensions are shown in inches. Operating Conditions Table 2-4 through Table 2-6 summarize the maximum ratings, recommended operating conditions, and DC operating conditions for the ByteBlaster II cable. Table 2-4. ByteBlaster II Cable Absolute Maximum Ratings Symbol VCC(TRGT) Parameter (Note 1) Conditions Min Max Unit Target supply voltage With respect to ground -0.3 5.5 V II Input current TDO or dataout -10.0 10.0 mA Io Output current TCK, TMS, TDI, nCS, nCE -20.0 20.0 mA Note to Table 2-4: (1) The operating conditions are identical for both leaded and lead-free ByteBlaster II download cables. ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Chapter 2: ByteBlaster II Specifications Statement of China-RoHS Compliance 2-5 Table 2-5. ByteBlaster II Cable Recommended Operating Conditions (Note 1) Symbol Parameter VCC(TRGT) Conditions Min Max Unit Target supply voltage, 5.0-V operation -- 4.75 5.25 V Target supply voltage, 3.3-V operation -- 3.0 3.6 V Target supply voltage, 2.5-V operation -- 2.375 2.625 V Target supply voltage, 1.8-V operation -- 1.71 1.89 V Target supply voltage, 1.5-V operation -- 1.43 1.57 V Note to Table 2-5: (1) The operating conditions are identical for both leaded and lead-free ByteBlaster II download cables. Table 2-6. ByteBlaster II Cable DC Operating Conditions Symbol (Note 1) Parameter Conditions Min Max Unit VIH High-level input voltage -- VCC(TRGT) -0.2 -- V VIL Low-level input voltage -- -- 0.15 V VOH 5.0-V high-level output voltage VCC(TRGT) = 4.5 V, IOH = 8 mA 4.4 -- V 3.3-V high-level output voltage VCC(TRGT) = 3.0 V, IOH = 4 mA 2.9 -- V 2.5-V high-level output voltage VCC(TRGT) = 2.375 V, IOH = 2 mA 2.275 -- V 1.8-V high-level output voltage VCC(TRGT) = 1.71 V, IOH = 2 mA 1.61 -- V 1.5-V high-level output voltage VCC(TRGT) = 1.43 V, IOH = 2 mA 1.33 -- V 5.0-V low-level output voltage VCC(TRGT) = 5.5 V, IOL = 8 mA -- 0.125 V 3.3-V low-level output voltage VCC(TRGT) = 3.6 V, IOL = 4 mA -- 0.125 V 2.5-V low-level output voltage VCC(TRGT) = 2.625 V, IOL = 2 mA -- 0.125 V 1.8-V low-level output voltage VCC(TRGT) = 1.89 V, IOL = 2 mA -- 0.125 V 1.5-V low-level output voltage VCC(TRGT) = 1.57 V, IOL = 2 mA -- 0.125 V Operating current (No Load) (Typical ICC = 80 mA) -- 150 mA VOL ICC (TRGT) Note to Table 2-6: (1) The DC operating conditions are identical for both leaded and lead-free ByteBlaster II download cables. 1 The RoHS sticker on the ByteBlaster II download cable reflects the hardware upgrade to meet the RoHS lead-free requirement. Statement of China-RoHS Compliance Table 2-7 lists hazardous substances included with the lead-free ByteBlaster II download cable. Table 2-7. Table of Hazardous Substances' Name and Concentration (Note 1) Lead (Pb) Cadmium (Cd) Hexavalent Chromium (Cr6+) Electronic Components 0 0 0 0 0 0 Populated Circuit Board 0 0 0 0 0 0 Part Name (c) July 2008 Altera Corporation Mercury (Hg) Polybrominated biphenyls (PBB) Polybrominated diphenyl Ethers (PBDE) ByteBlaster II Download Cable User Guide 2-6 Chapter 2: ByteBlaster II Specifications Statement of China-RoHS Compliance Table 2-7. Table of Hazardous Substances' Name and Concentration (Note 1) Part Name Lead (Pb) Cadmium (Cd) Hexavalent Chromium (Cr6+) Mercury (Hg) Polybrominated biphenyls (PBB) Polybrominated diphenyl Ethers (PBDE) Manufacturing Process 0 0 0 0 0 0 Packing 0 0 0 0 0 0 Notes to Table 2-7: (1) 0 indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Info. Additional Information Referenced Documents For more information about configuration and in-system programmability (ISP), refer to the following sources: AN 39: IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices AN 95: In-System Programmability in MAX Devices Configuring Arria GX Devices chapter in volume 2 of the Arria GX Device Handbook Configuring Cyclone FPGAs chapter in the Cyclone Device Handbook Configuring Cyclone II Devices chapter in the Cyclone II Device Handbook Configuring Cyclone III Devices chapter in volume 1 of the Cyclone III Device Handbook Configuring Stratix and Stratix GX Devices chapter in the Stratix Device Handbook Configuring Stratix II and Stratix II GX Devices chapter in volume 2 of the Stratix II Device Handbook Configuring Stratix III Devices chapter in volume 1 of the Stratix III Device Handbook In-System Programmability Guidelines for MAX II Devices chapter in the MAX II Device Handbook Configuration, Design Security, and Remote System Upgrades in Stratix IV Devices chapter in volume 1 of the Stratix IV Device Handbook Programming & Configuration chapter in the Introduction to the Quartus II Software manual Quartus II Programmer chapter in volume 3 of the Quartus II Handbook Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet chapter in the Configuration Handbook Programming module of the Quartus(R) II online tutorial Refer to the following glossary definitions in Quartus II Help: (c) July 2008 Altera Corporation ByteBlaster II Cable (general description) Configuration scheme (general description) Programming files (general description) Refer to the following procedures in Quartus II Help: Programming a Single Device or Multiple Devices in JTAG or Passive Serial Mode Programming a Single Device in Active Serial Programming Mode Selecting the Communications Cable for the SignalTap II Logic Analyzer ByteBlaster II Download Cable User Guide Info-2 Revision History Refer to the following introduction and overview topics in Quartus II Help: Programmer Introduction Overview: Working with Chain Description Files Overview: Converting Programming Files Revision History The following table shows the revision history of this user guide. Table Info-1. Revision History Date and Document Version Changes Made July 2008 Updates included: v1.4 Added the "Additional Information" page General update to the format and style of the user guide Updated the "Supported Devices" section Updated the "Setting Up the ByteBlaster II Hardware in the Quartus II Software" section Updated Table 2-1 Added a hand note to the "Circuit Board Header Connection" section Updated Table 2-6 April 2008 Added "Statement of China-RoHS Compliance" section. v1.3 Added Table 2-7. January 2008 Updated "Supported Devices" section. v1.2 Updated Table 1-1. Summary of Changes -- -- -- Updated Table 2-1. Added new note to Table 2-4,Table 2-5, andTable 2-6. Added note about RoHS compliance. Updated "Revision History" December 2004 Re-release -- Initial release -- v1.1 July 2004 v1.0 ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Info-3 How to Contact Altera How to Contact Altera For the most up-to-date information about Altera(R) products, refer to the following table. Table Info-2. How to Contact Altera Contact (1) Technical support Technical training Contact Method Address Website www.altera.com/support Website www.altera.com/training Email custrain@altera.com Product literature Website www.altera.com/literature Altera literature services Email literature@altera.com Non-technical support (General) Email nacomp@altera.com (Software Licensing) Email authorization@altera.com Note to Table Info-2 (1) You can also contact your local Altera sales office or sales representative. Typographic Conventions This document uses the typographic conventions shown below. Table Info-3. Typographic Conventions Visual Cue (Part 1 of 2) Meaning Bold Type with Initial Capital Letters Command names, dialog box titles, checkbox options, and dialog box options are shown in bold, initial capital letters. Example: Save As dialog box. bold type External timing parameters, directory names, project names, disk drive names, filenames, filename extensions, and software utility names are shown in bold type. Examples: fMAX, \qdesigns directory, d: drive, chiptrip.gdf file. Italic Type with Initial Capital Letters Document titles are shown in italic type with initial capital letters. Example: AN 75: High-Speed Board Design. Italic type Internal timing parameters and variables are shown in italic type. Examples: tPIA, n + 1. Variable names are enclosed in angle brackets (< >) and shown in italic type. Example: <file name>, <project name>.pof file. Initial Capital Letters Keyboard keys and menu names are shown with initial capital letters. Examples: Delete key, the Options menu. "Subheading Title" References to sections within a document and titles of on-line help topics are shown in quotation marks. Example: "Typographic Conventions." Courier type Signal and port names are shown in lowercase Courier type. Examples: data1, tdi, input. Active-low signals are denoted by suffix n, for example, resetn. Anything that must be typed exactly as it displays is shown in Courier type. For example: c:\qdesigns\tutorial\chiptrip.gdf. Also, sections of an actual file, such as a Report File, references to parts of files (for example, the AHDL keyword SUBDESIGN), as well as logic function names (e.g., TRI) are shown in Courier. 1., 2., 3., and a., b., c., etc. Numbered steps are used in a list of items when the sequence of the items is important, such as the steps listed in a procedure. * Bullets are used in a list of items when the sequence of the items is not important. v The checkmark indicates a procedure that consists of one step only. (c) July 2008 Altera Corporation ByteBlaster II Download Cable User Guide Info-4 Typographic Conventions Table Info-3. Typographic Conventions Visual Cue (Part 2 of 2) Meaning 1 The hand points to information that requires special attention. c A caution calls attention to a condition or possible situation that can damage or destroy the product or the user's work. w A warning calls attention to a condition or possible situation that can cause injury to the user. r The angled arrow indicates you should press the Enter key. f The feet direct you to more information about a particular topic. ByteBlaster II Download Cable User Guide (c) July 2008 Altera Corporation Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Altera: PL-BYTEBLASTER2N