SLD1133VL-40 650nm Index-Guided Red Laser Diode Description The SLD1133VL-40 is a index-guided red laser diode for Laser pointer. The wavelength is 20nm shorter than that of the current diodes. M-274 Features * Small astigmatism (7m typ.) * Small package (5.6mm) * Single longitudinal mode * Low operating voltage (2.5V Max) * Max operating temperature = 40C (Case temperature) Applications Laser pointer Structure * AlGaInP MQW laser diode * PIN photodiode to monitor laser beam output Recommended Optical Power Output 5mW Absolute Maximum Ratings (Tc = 25C) * Optical power output Po 5 mW * Reverse voltage VR LD 2 V PD 15 V * Operating temperature Topr -10 to +40 C * Storage temperature Tstg -40 to +85 C Pin Configuration Connection Diagram 3 COMMON LD PD 2 2 1 1 3 1. LD anode 2. PD anode 3. COMMON Bottom View Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E97426-PS SLD1133VL-40 Electrical and Optical Characteristics (Tc = 25C) Item Symbol Tc: Case temperature Conditions Min. Typ. Max. Unit 50 65 mA Threshold current Ith Operating current Iop Po = 5mW 60 70 mA Operating voltage Vop Po = 5mW 2.3 2.5 V Wavelength p Po = 5mW 650 660 nm 24 30 40 degree 5 8 12 degree 80 m 3 degree 3 degree 0.4 0.7 mW/mA 7 15 m 0.1 0.3 mA Radiation angle Positional accuracy Perpendicular Parallel // Position X, Y, Z Angle // Po = 5mW Po = 5mW Differential efficiency D Po = 5mW Astigmatism As Po = 5mW Monitor current Imon Po = 5mW, VR = 5V 0.15 0.05 Handling Precautions (1) Eye protection against laser beams The optical output of laser diodes ranges from several mW to 4W. However the optical power density of the laser beam at the diode chip reaches 1MW/cm2. Unlike gas lasers, since laser diode beams are divergent, uncollimated laser diode beams are fairly safe at a laser diode. For observing laser beams, ALWAYS use safety goggles that block infrared rays. Usage of IR scopes, IR cameras and fluorescent plates is also recommended for monitoring laser beams safely. Safety goggles for protection from laser beam Laser diode Lens Optical material IR fluorescent plate Optical board Optical power output control device Temperature control device (2) Prevention of surge current and electrostatic discharge Laser diode is most sensitive to electrostatic discharge among semiconductors. When a large current is passed through the laser diode even for an extremely short time (in the order of nanosecond), the strong light emitted from the laser diode promotes deterioration and then laser diodes are destroyed. Therefore, note that the surge current should not flow the laser diode driving circuit from switches and others. Also, if the laser diode is handled carelessly, it may be destructed instantly because electrostatic discharge is easily applied by a human body. Be great careful about excess current and electrostatic discharge. -2- SLD1133VL-40 Package Outline Unit: mm M-274 Reference Slot 0.4 1.0 0.5 90 3 1 2 0 5.6 - 0.025 4.4 MAX 3.7 MAX 1.0 MIN 1.2 0.1 Reference Plane 2 3 1 3 - 0.45 Optical Distance = 1.35 0.08 6.5 LD Chip & Photo Diode SONY CODE 2.6 MAX 0.5 MIN 1.26 0.25 Window Glass PCD 2.0 M-274 PACKAGE WEIGHT EIAJ CODE JEDEC CODE -3- 0.3g