LTC2320-14 Octal, 14-Bit + Sign, 1.5Msps/Ch Simultaneous Sampling ADC DESCRIPTION FEATURES 1.5Msps/Ch Throughput Rate nn Eight Simultaneously Sampling Channels nn Guaranteed 14-Bit, No Missing Codes nn 8V P-P Differential Inputs with Wide Input Common Mode Range nn 81dB SNR (Typ) at f = 500kHz IN nn -90dB THD (Typ) at f = 500kHz IN nn Guaranteed Operation to 125C nn Single 3.3V or 5V Supply nn Low Drift (20ppm/C Max) 2.048V or 4.096V Internal Reference nn 1.8V to 2.5V I/O Voltages nn CMOS or LVDS SPI-Compatible Serial I/O nn Power Dissipation 20mW/Ch (Typ) nn Small 52-Lead (7mm x 8mm) QFN Package The LTC(R)2320-14 is a low noise, high speed octal 14bit + sign successive approximation register (SAR) ADC with differential inputs and wide input common mode range. Operating from a single 3.3V or 5V supply, the LTC2320-14 has an 8VP-P differential input range, making it ideal for applications which require a wide dynamic range with high common mode rejection. The LTC2320-14 achieves 1LSB INL typical, no missing codes at 14 bits and 81dB SNR. nn The LTC2320-14 has an onboard low drift (20ppm/C max) 2.048V or 4.096V temperature-compensated reference. The LTC2320-14 also has a high speed SPI-compatible serial interface that supports CMOS or LVDS. The fast 1.5Msps per channel throughput with no latency makes the LTC2320-14 ideally suited for a wide variety of high speed applications. The LTC2320-14 dissipates only 20mW per channel and offers nap and sleep modes to reduce the power consumption to 26W for further power savings during inactive periods. APPLICATIONS High Speed Data Acquisition Systems Communications nn Optical Networking nn Multiphase Motor Control nn nn L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION 10F 1F 1.8V TO 2.5V 3.3V OR 5V IN+, IN - VDD ARBITRARY 0V VDD 0V VDD DIFFERENTIAL VDD AIN2+ S/H AIN2- AIN3+ S/H AIN3- AIN4+ S/H AIN4- 0V BIPOLAR AIN1+ S/H AIN1- UNIPOLAR 0V AIN5+ S/H AIN5- AIN6+ S/H AIN6- AIN7+ S/H AIN7- AIN8+ S/H AIN8- REF EIGHT SIMULTANEOUS SAMPLING CHANNELS VDD GND GND MUX 14-BIT + SIGN SAR ADC CMOS/LVDS SDR/DDR REFBUFEN MUX 14-BIT + SIGN SAR ADC SDO1 SDO2 SDO3 SDO4 SDO5 SDO6 SDO7 SDO8 CLKOUT SCK LTC2320-14 MUX 14-BIT + SIGN SAR ADC CNV MUX 32k Point FFT fSMPL = 1.5Msps, fIN = 500kHz OVDD SAMPLE CLOCK 10F -60 -80 -100 -140 232014 TA01a 10F IN SNR = 81.1dB THD = -90.2dB -20 SINAD = 80.8dB SFDR = 94.7dB -40 -120 14-BIT + SIGN SAR ADC REFOUT1 REFOUT2 REFOUT3 REFOUT4 1F SMPL 0 AMPLITUDE (dBFS) TRUE DIFFERENTIAL INPUTS NO CONFIGURATION REQUIRED 10F 10F 0 0.1 0.2 0.3 0.4 0.5 FREQUENCY (MHz) 0.6 0.7 232014 TA01b 232014f For more information www.linear.com/LTC2320-14 1 LTC2320-14 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION SCK/SCK+ DNC/SCK- VDD REFOUT4 GND AIN8- AIN8+ GND AIN7- AIN7+ VDD TOP VIEW 52 51 50 49 48 47 46 45 44 43 42 41 AIN6- 1 40 SDO8/SDOD- AIN6+ 2 39 SDO7/SDOD+ GND 3 38 GND AIN5- 4 37 OVDD AIN5+ 5 36 SDO6/SDOC- REFOUT3 6 35 SDO5/SDOC+ GND 7 34 CLKOUTEN/CLKOUT - 53 GND REF 8 33 CLKOUT/CLKOUT+ 32 GND REFOUT2 9 AIN4- 10 31 OVDD AIN4+ 11 30 SDO4/SDOB- GND 12 29 SDO3/SDOB+ AIN3- 13 28 SDO2/SDOA- AIN3+ 14 27 SDO1/SDOA+ GND CMOS/LVDS CNV SDR/DDR VDD REFOUT1 AIN1+ GND AIN1- AIN2+ VDD 15 16 17 18 19 20 21 22 23 24 25 26 AIN2- Supply Voltage (VDD)...................................................6V Supply Voltage (OVDD).................................................3V Analog Input Voltage AIN+, AIN - (Note 3).................... -0.3V to (VDD + 0.3V) REFOUT1,2,3,4........................ .-0.3V to (VDD + 0.3V) CNV........................................ -0.3V to (OVDD + 0.3V) Digital Input Voltage (Note 3)........................... (GND - 0.3V) to (OVDD + 0.3V) Digital Output Voltage (Note 3)........................... (GND - 0.3V) to (OVDD + 0.3V) Operating Temperature Range LTC2320C................................................. 0C to 70C LTC2320I..............................................-40C to 85C LTC2320H........................................... -40C to 125C Storage Temperature Range................... -65C to 150C REFBUFEN (Notes 1, 2) UKG PACKAGE 52-LEAD (7mm x 8mm) PLASTIC QFN TJMAX = 150C, JA = 31C/W EXPOSED PAD (PIN 53) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION http://www.linear.com/product/LTC2320-14#orderinfo LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2320CUKG-14#PBF LTC2320CUKG-14#TRPBF LTC2320UKG-14 52-Lead (7mm x 8mm) Plastic QFN 0C to 70C LTC2320IUKG-14#PBF LTC2320IUKG-14#TRPBF LTC2320UKG-14 52-Lead (7mm x 8mm) Plastic QFN -40C to 85C LTC2320HUKG-14#PBF LTC2320HUKG-14#TRPBF LTC2320UKG-14 52-Lead (7mm x 8mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 2 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS Absolute Input Range (AIN+ to AIN-) Absolute Input Range (AIN+ to AIN-) VIN+ - VIN- Input Differential Voltage Range VCM Common Mode Input Range VIN = VIN+ - VIN- VCM = (VIN+ - VIN-)/2 IIN Analog Input DC Leakage Current + VIN VIN- MIN MAX UNITS 0 VDD V 0 VDD V l -REFOUT1,2,3,4 REFOUT1,2,3,4 V l 0 VDD V l -1 1 A (Note 5) l (Note 5) l CIN Analog Input Capacitance CMRR Input Common Mode Rejection Ratio VIHCNV CNV High Level Input Voltage l VILCNV CNV Low Level Input Voltage l IINCNV CNV Input Current l TYP fIN = 500kHz 10 pF 102 dB 1.5 V -10 0.5 V 10 A CONVERTER CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS MIN Resolution l 14 No Missing Codes l 14 Transition Noise INL Integral Linearity Error DNL Differential Linearity Error BZE Bipolar Zero-Scale Error MAX (Note 6) UNITS Bits Bits 0.8 LSBRMS l -3 1 3 LSB l -0.99 0.4 0.99 LSB (Note 7) l -3 0 3 LSB Bipolar Full-Scale Error VREFOUT1,2,3,4 = 4.096V (REFBUFEN Grounded) (Note 7) l -8 Bipolar Full-Scale Error Drift VREFOUT1,2,3,4 = 4.096V (REFBUFEN Grounded) Bipolar Zero-Scale Error Drift FSE TYP 0.005 0 15 LSB/C 8 LSB ppm/C 232014f For more information www.linear.com/LTC2320-14 3 LTC2320-14 DYNAMIC ACCURACY The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C and AIN = -1dBFS (Notes 4, 8). SYMBOL PARAMETER SINAD CONDITIONS MIN Signal-to-(Noise + Distortion) Ratio fIN = 500kHz, VREFOUT1,2,3,4 = 4.096V, Internal Reference l 75.5 fIN = 500kHz, VREFOUT1,2,3,4 = 5V, External Reference SNR Signal-to-Noise Ratio fIN = 500kHz, VREFOUT1,2,3,4 = 4.096V, Internal Reference l 76.5 fIN = 500kHz, VREFOUT1,2,3,4 = 5V, External Reference THD Total Harmonic Distortion fIN = 500kHz, VREFOUT1,2,3,4 = 4.096V, Internal Reference SFDR Spurious Free Dynamic Range fIN = 500kHz, VREFOUT1,2,3,4 = 4.096V, Internal Reference MAX fIN = 500kHz, VREFOUT1,2,3,4 = 5V, External Reference 77 fIN = 500kHz, VREFOUT1,2,3,4 = 5V, External Reference UNITS 80 dB 84 dB 81 dB 82.5 dB -90 l l TYP -77 dB -91 dB 93 dB 93 dB -3dB Input Bandwidth 55 MHz Aperture Delay 500 ps Aperture Delay Matching 500 Aperture Jitter Transient Response Full-Scale Step ps 1 psRMS 3 ns INTERNAL REFERENCE CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS VREFOUT1,2,3,4 Internal Reference Output Voltage 4.75V < VDD < 5.25V 3.13V < VDD < 3.47V l l VREF Temperature Coefficient (Note 14) l MIN TYP MAX UNITS 4.078 2.034 4.096 2.048 4.115 2.064 V V 3 20 REFOUT1,2,3,4 Output Impedance IREFOUT1,2,3,4 4 ppm/C 0.25 VREFOUT1,2,3,4 Line Regulation 4.75V < VDD < 5.25V 0.3 mV/V External Reference Current REFBUFEN = 0V REFOUT1,2,3,4 = 4.096V REFOUT1,2,3,4 = 2.048V (Notes 9, 10) 385 204 A A 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 DIGITAL INPUTS AND DIGITAL OUTPUTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS CMOS Digital Inputs and Outputs MIN TYP MAX UNITS CMOS/LVDS = GND VIH High Level Input Voltage l VIL Low Level Input Voltage l IIN Digital Input Current CIN Digital Input Capacitance VOH High Level Output Voltage IO = -500A l VOL Low Level Output Voltage IO = 500A l IOZ Hi-Z Output Leakage Current VOUT = 0V to OVDD l ISOURCE Output Source Current VOUT = 0V l -10 mA ISINK Output Sink Current VOUT = OVDD l 10 mA VIN = 0V to OVDD l 0.8 * OVDD -10 0.2 * OVDD V 10 A 5 l LVDS Digital Inputs and Outputs V pF OVDD - 0.2 V 0.2 -10 10 V A CMOS/LVDS = OVDD VID LVDS Differential Input Voltage 100 Differential Termination OVDD = 2.5V l 240 600 mV VIS LVDS Common Mode Input Voltage 100 Differential Termination OVDD = 2.5V l 1 1.45 V VOD LVDS Differential Output Voltage 100 Differential Termination OVDD = 2.5V l 220 350 600 mV VOS LVDS Common Mode Output Voltage 100 Differential Termination OVDD = 2.5V l 0.85 1.2 1.4 V VOD_LP Low Power LVDS Differential Output Voltage 100 Differential Termination OVDD = 2.5V l 100 200 350 mV VOS_LP Low Power LVDS Common Mode Output Voltage 100 Differential Termination OVDD = 2.5V l 0.85 1.2 1.4 V 232014f For more information www.linear.com/LTC2320-14 5 LTC2320-14 POWER REQUIREMENTS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS VDD Supply Voltage 5V Operation 3.3V Operation l l IVDD Supply Current 1.5Msps Sample Rate (IN+ = IN- = 0V) l CMOS I/O Mode MIN TYP 4.75 3.13 31 UNITS 5.25 3.47 V V 38 mA CMOS/LVDS = GND OVDD Supply Voltage IOVDD Supply Current 1.5Msps Sample Rate (CL = 5pF) l 4.4 INAP Nap Mode Current Conversion Done (IVDD) l ISLEEP Sleep Mode Current Sleep Mode (IVDD + IOVDD) l PD_3.3V Power Dissipation VDD = 3.3V, 1.5Msps Sample Rate Nap Mode Sleep Mode PD_5V Power Dissipation VDD = 5V, 1.5Msps Sample Rate Nap Mode Sleep Mode LVDS I/O Mode MAX 2.63 V 7.0 mA 5.3 6.2 mA 20 110 A l l l 102 18 20 130 20.6 355 mW mW W l l l 162 27 30 208 31.2 525 mW mW W 2.63 V l 1.71 CMOS/LVDS = OVDD, OVDD = 2.5V OVDD Supply Voltage IOVDD Supply Current 1.5Msps Sample Rate (CL = 5pF, RL = 100) l 26 INAP Nap Mode Current Conversion Done (IVDD) l ISLEEP Sleep Mode Current Sleep Mode (IVDD + IOVDD) l PD_3.3V Power Dissipation VDD = 3.3V, 1.5Msps Sample Rate Nap Mode Sleep Mode PD_5V Power Dissipation VDD = 5V, 1.5Msps Sample Rate Nap Mode Sleep Mode l 2.37 34 mA 5.3 6.2 mA 20 110 A l l l 151 52 80 195 58 355 mW mW W l l l 214 60 30 280 68.5 525 mW mW W ADC TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER fSMPL Maximum Sampling Frequency tCYC Time Between Conversions tCONV Conversion Time l tCNVH CNV High Time l tACQUISITION Sampling Aperture (Note 11) tACQUISITION = tCYC - tCONV 215 ns tWAKE REFOUT1,2,3,4 Wake-Up Time CREFOUT1,2,3,4 = 10F 50 ms CMOS I/O Mode, SDR CONDITIONS (Note 11) tCYC = tCNVH + tCONV + tREADOUT TYP l 0.667 MAX UNITS 1.5 Msps 1000 450 30 s ns ns CMOS/LVDS = GND, SDR/ DDR = GND tSCK SCK Period tSCKH tSCKL tHSDO_SDR SDO Data Remains Valid Delay from CLKOUT tDSCKCLKOUT SCK to CLKOUT Delay 6 MIN l (Note 13) l 9.1 ns SCK High Time l 4.1 ns SCK Low Time l 4.1 ns CL = 5pF (Note 12) l 0 1.5 ns (Note 12) l 2 4.5 ns 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 ADC TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C (Note 4). SYMBOL PARAMETER CONDITIONS tDCNVSDOZ Bus Relinquish Time After CNV (Note 11) l 3 ns tDCNVSDOV SDO Valid Delay from CNV (Note 11) l 3 ns tDSCKHCNVH SCK Delay Time to CNV (Note 11) l 0 CMOS I/O Mode, DDR MIN TYP MAX UNITS ns CMOS/LVDS = GND, SDR/ DDR = OVDD tSCK SCK Period l 18.2 ns tSCKH SCK High Time l 8.2 ns tSCKL SCK Low Time l 8.2 ns tHSDO_DDR SDO Data Remains Valid Delay from CLKOUT CL = 5pF (Note 12) l 0 1.5 ns tDSCKCLKOUT SCK to CLKOUT Delay (Note 12) l 2 4.5 ns tDCNVSDOZ Bus Relinquish Time After CNV (Note 11) l 3 ns tDCNVSDOV SDO Valid Delay from CNV (Note 11) l 3 ns tDSCKHCNVH SCK Delay Time to CNV (Note 11) l 0 ns LVDS I/O Mode, SDR CMOS/LVDS = OVDD, SDR/DDR = GND tSCK SCK Period l 3.3 ns tSCKH SCK High Time l 1.5 ns tSCKL SCK Low Time l 1.5 ns tHSDO_SDR SDO Data Remains Valid Delay from CLKOUT CL = 5pF (Note 12) l 0 1.5 ns tDSCKCLKOUT SCK to CLKOUT Delay (Note 12) l 2 4 ns tDSCKHCNVH SCK Delay Time to CNV (Note 11) l 0 ns LVDS I/O Mode, DDR CMOS/LVDS = OVDD, SDR/DDR = OVDD = 2.5V tSCK SCK Period l 6.6 ns tSCKH SCK High Time l 3 ns tSCKL SCK Low Time l 3 ns tHSDO_DDR SDO Data Remains Valid Delay from CLKOUT l 0 1.5 ns tDSCKCLKOUT SCK to CLKOUT Delay l 2 4 ns tDSCKHCNVH SCK Delay Time to CNV l 0 CL = 5pF (Note 11) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground. Note 3: When these pin voltages are taken below ground, or above VDD or OVDD, they will be clamped by internal diodes. This product can handle input currents up to 100mA below ground, or above VDD or OVDD, without latch-up. Note 4: VDD = 5V, OVDD = 2.5V, REFOUT1,2,3,4 = 4.096V, fSMPL = 1.5MHz. Note 5: Recommended operating conditions. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 7: Bipolar zero error is the offset voltage measured from -0.5LSB when the output code flickers between 000 0000 0000 0000 and 111 1111 1111 1111. Full-scale bipolar error is the worst-case of -FS or +FS ns untrimmed deviation from ideal first and last code transitions and includes the effect of offset error. Note 8: All specifications in dB are referred to a full-scale 4.096V input with REF = 4.096V. Note 9: When REFOUT1,2,3,4 is overdriven, the internal reference buffer must be turned off by setting REFBUFEN = 0V. Note 10: fSMPL = 1.5MHz, IREFOUT1,2,3,4 varies proportionally with sample rate. Note 11: Guaranteed by design, not subject to test. Note 12: Parameter tested and guaranteed at OVDD = 1.71V and OVDD = 2.5V. Note 13: tSCK of 9.1ns allows a shift clock frequency up to 105MHz for rising edge capture. Note 14: Temperature coefficient is calculated by dividing the maximum change in output voltage by the specified temperature range. Note 15: CNV is driven from a low jitter digital source, typically at OVDD logic levels. 232014f For more information www.linear.com/LTC2320-14 7 LTC2320-14 ADC TIMING CHARACTERISTICS 0.8 * OVDD tWIDTH 0.2 * OVDD tDELAY tDELAY 0.8 * OVDD 0.8 * OVDD 0.2 * OVDD 0.2 * OVDD 50% 50% 232014 F01 Figure 1. Voltage Levels for Timing Specifications 8 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 TYPICAL PERFORMANCE CHARACTERISTICS = 4.096V, fSMPL = 1.5Msps, unless otherwise noted. Integral Nonlinearity vs Output Code TA = 25C, VDD = 5V, OVDD = 2.5V, REFOUT1,2,3,4 Differential Nonlinearity vs vs Output Output Code Code 2.0 DC DC Histogram HISTOGRAM 1.0 30 24 0.5 0 -0.5 -1.0 NUMBER OF PARTS 0.5 DNL ERROR (LSB) INL ERROR (LSB) 1.0 0 -0.5 0 8192 OUTPUT CODE 16384 -8192 -60 -80 -100 -120 0.2 0.3 0.4 0.5 FREQUENCY (MHz) 0.6 0.7 -84 81.6 81.4 SNR 81.2 81.0 SINAD 80.8 80.6 80.4 80.0 -108 HD3 -112 -116 -120 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 INPUT COMMON MODE (V) 232014 G07 1 2 3 THD -96 -100 HD3 -104 HD2 -108 -112 -116 0 0.1 0.2 0.3 0.4 0.5 0.6 FREQUENCY (MHz) 0.7 0.8 -120 0 0.1 83 f = 500kHz 82 IN 81 80 79 78 77 76 75 74 73 72 71 70 69 0.5 1 1.5 2 0.2 0.3 0.4 0.5 0.6 FREQUENCY (MHz) 0.7 0.8 232014 G06 0 SNR 32k Point FFT, IMD, fSMPL = 1.5Msps, + = 490kHz, A - = 510kHz AININ ININ THD = 86dB VCM = 20kHz, 4VP-P -20 SINAD AMPLITUDE (dBFS) -104 HD2 0 CODE -92 SNR, SINAD vs Reference Voltage, fININ = 500kHz SNR, SINAD LEVEL (dBFS) THD, HARMONICS LEVEL (dBFS) -96 -100 -1 -88 232014 G05 fIN = 500kHz THD -2 232014 G03 -80 THD, Harmonics vs Input Common -92 -3 THD, Harmonics vs Input Frequency (1kHz to 750kHz) (1kHz to 750kHz) 80.2 0.1 0 16384 81.8 Mode -88 9 82.0 232014 G04 -84 12 SNR, SINAD vs Input Frequency (1kHz to 750kHz) IN SNR = 81.1dB THD = -90.2dB -20 SINAD = 80.8dB SFDR = 94.7dB -40 -80 15 232014 G02 SNR, SINAD LEVEL (dBFS) AMPLITUDE (dBFS) 32k Point FFT, fSMPL = 1.5Msps, fIN = 500kHz SMPL 0 8192 OUTPUT CODE THD, HARMONICS LEVEL (dBFS) -8192 -1.0 -16384 232014 G01 0 18 3 -2.0 -16384 -140 21 6 -1.5 0 = 0.72 27 1.5 -40 -60 -80 -100 -120 2.5 3 3.5 VREF(V) 4 4.5 5 232014 G08 -140 0 0.1 0.2 0.3 0.4 0.5 FREQUENCY (MHz) 0.6 0.7 232014 G09 232014f For more information www.linear.com/LTC2320-14 9 LTC2320-14 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C, VDD = 5V, OVDD = 2.5V, REFOUT1,2,3,4 = 4.096V, fSMPL = 1.5Msps, unless otherwise noted. CMRR vs Input Frequency CMRR vs Input Frequency 120 (Large Signal Settling) Crosstalk vs Input Frequency 16384 -90 VCM = 4VP-P -91 115 12288 -92 105 100 OUTPUT CODE (LSB) -93 CROSSTALK (dB) 110 CMRR (dB) Step Response (Large Signal Settling) Crosstalk vs Input Frequency -94 -95 -96 -97 8192 4.096V RANGE 4096 0 -98 95 IN+ = 1.5MHz SQUARE WAVE IN- = 0V -99 0 500 1000 FREQUENCY (kHz) 1500 -100 0 100 232014 G10 REF REF Output Output vs vs Temperature Temperature 1.0 REFBUFEN = 0V 350 (EXT REF BUF 50 25 0 -25 -50 4.096V RANGE -75 IN+ = 1.5MHz SQUARE WAVE 300 250 200 VREFOUT1,2,3,4 = 4.096V 150 100 VREFOUT1,2,3,4 = 2.048V 50 IN- = 0V 0.5 OVERDRIVING REF BUF) 0 0 0.3 0.6 0.9 1.2 SAMPLE FREQUENCY (Msps) 1.5 SUPPLY CURRENT (mA) -0.5 -1 5 25 45 65 85 105 125 TEMPERATURE (C) 232014 G16 -1.0 VDD = 5V -1.5 -2.0 -3.0 -55 -35 -15 1.5 5 25 45 65 85 105 125 TEMPERATURE (C) 232014 G15 33 8 31 7 29 VDD = 5V 27 25 VDD = 3.3V 23 CMOS(1.8V, 8 LANES) 3 26 24 22 20 18 2 0 232014 G17 CMOS (2.5V, 8 LANES) 4 19 1.5 30 LVDS (4 LANES) 28 5 1 0.3 0.6 0.9 1.2 SAMPLE FREQUENCY (Msps) 32 FULL SCALE SINUSOIDAL INPUT 6 21 0 OVDD Current vs SCK Frequency, CLOAD LOAD = 10pF LOW POWER LVDS (4 LANES) 16 OVDD CURRENT LVDS (mA) 1 0 -0.5 -2.5 Supply Current vs Sample Frequency Offset OffsetError Errorvs vsTemperature Temperature 0.5 VDD = 3.3V 0 232014 G14 232014 G13 -1.5 -55 -35 -15 REF OUTPUT ERROR (mV) SUPPLY CURRENT (uA) 75 -125 -20 -10 0 10 20 30 40 50 60 70 80 90 SETTLING TIME (ns) LSB 232014 G12 400 100 10 -4096 -20 -10 0 10 20 30 40 50 60 70 80 90 SETTLING TIME (ns) 700 External Reference Supply Current Current vs vs Sample Sample Frequency Frequency 125 DEVIATION FROM FINAL VALUE (LSB) 600 232014 G11 Step Response (Fine (Fine Settling) Settling) -100 200 300 400 500 FREQUENCY (kHz) OVDD CURRENT CMOS (mA) 90 14 0 50 100 150 200 250 SCK FREQUENCY (MHz) 12 300 232014 G18 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 PIN FUNCTIONS Pins that are the same for all digital I/O modes. AIN6+, AIN6- (Pins 2, 1): Analog Differential Input Pins. Full-scale range (AIN6+ - AIN6-) is REFOUT3 voltage. These pins can be driven from VDD to GND. GND (Pins 3, 7, 12, 18, 26, 32, 38, 46, 49): Ground. These pins and exposed pad (Pin 53) must be tied directly to a solid ground plane. AIN5+, AIN5- (Pins 5, 4): Analog Differential Input Pins. Full-scale range (AIN5+ - AIN5-) is REFOUT3 voltage. These pins can be driven from VDD to GND. REFOUT3 (Pin 6): Reference Buffer 3 Output. An onboard buffer nominally outputs 4.096V to this pin. This pin is referred to GND and should be decoupled closely to the pin with a 10F (X5R, 0805 size) ceramic capacitor. The internal buffer driving this pin may be disabled by grounding the REFBUFEN pin. If the buffer is disabled, an external reference may drive this pin in the range of 1.25V to 5V. REF (Pin 8): Common 4.096V reference output. Decouple to GND with a 1F low ESR ceramic capacitor. May be overdriven with a single external reference to establish a common reference for ADC cores 1 through 4. REFOUT2 (Pin 9): Reference Buffer 2 Output. An onboard buffer nominally outputs 4.096V to this pin. This pin is referred to GND and should be decoupled closely to the pin with a 10F (X5R, 0805 size) ceramic capacitor. The internal buffer driving this pin may be disabled by grounding the REFBUFEN pin. If the buffer is disabled, an external reference may drive this pin in the range of 1.25V to 5V. AIN4+, AIN4- (Pins 11, 10): Analog Differential Input Pins. Full-scale range (AIN4+ - AIN4-) is REFOUT2 voltage. These pins can be driven from VDD to GND. AIN3+, AIN3- (Pins 14, 13): Analog Differential Input Pins. Full-scale range (AIN3+ - AIN3-) is REFOUT2 voltage. These pins can be driven from VDD to GND. VDD (Pins 15, 21, 44, 52): Power Supply. Bypass VDD to GND with a 10F ceramic capacitor and a 0.1F ceramic capacitor close to the part. The VDD pins should be shorted together and driven from the same supply. AIN2+, AIN2- (Pins 17, 16): Analog Differential Input Pins. Full-scale range (AIN2+ - AIN2-) is REFOUT1 voltage. These pins can be driven from VDD to GND. AIN1+, AIN1- (Pins 20, 19): Analog Differential Input Pins. Full-scale range (AIN1+ - AIN1-) is REFOUT1 voltage. These pins can be driven from VDD to GND. REFOUT1 (Pin 22): Reference Buffer 1 Output. An onboard buffer nominally outputs 4.096V to this pin. This pin is referred to GND and should be decoupled closely to the pin with a 10F (X5R, 0805 size) ceramic capacitor. The internal buffer driving this pin may be disabled by grounding the REFBUFEN pin. If the buffer is disabled, an external reference may drive this pin in the range of 1.25V to 5V. SDR/DDR (Pin 23): Double Data Rate Input. Controls the frequency of SCK and CLKOUT. Tie to GND for the falling edge of SCK to shift each serial data output (Single Data Rate, SDR). Tie to OVDD to shift serial data output on each edge of SCK (Double Data Rate, DDR). CLKOUT will be a delayed version of SCK for both pin states. CNV (Pin 24): Convert Input. This pin, when high, defines the acquisition phase. When this pin is driven low, the conversion phase is initiated and output data is clocked out. This input must be driven at OVDD levels with a low jitter pulse. This pin is unaffected by the CMOS/LVDS pin. CMOS/LVDS (Pin 25): I/O Mode Select. Ground this pin to enable CMOS mode, tie to OVDD to enable LVDS mode. Float this pin to enable low power LVDS mode. OVDD (Pins 31, 37): I/O Interface Digital Power. The range of OVDD is 1.71V to 2.63V. This supply is nominally set to the same supply as the host interface (CMOS: 1.8V or 2.5V, LVDS: 2.5V). Bypass OVDD to GND (Pins 32 and 38) with 0.1F capacitors. 232014f For more information www.linear.com/LTC2320-14 11 LTC2320-14 PIN FUNCTIONS REFBUFEN (Pin 43): Reference Buffer Output Enable. Tie to VDD when using the internal reference. Tie to ground to disable the internal REFOUT1-4 buffers for use with external voltage references. This pin has a 500k internal pull-up to VDD. REFOUT4 (Pin 45): Reference Buffer 4 Output. An onboard buffer nominally outputs 4.096V to this pin. This pin is referred to GND and should be decoupled closely to the pin with a 10F (X5R, 0805 size) ceramic capacitor. The internal buffer driving this pin may be disabled by grounding the REFBUFEN pin. If the buffer is disabled, an external reference may drive this pin in the range of 1.25V to 5V. AIN8+, AIN8- (Pins 48, 47): Analog Differential Input Pins. Full-scale range (AIN8+ - AIN8-) is REFOUT4 voltage. These pins can be driven from VDD to GND. AIN7+, AIN7- (Pins 51, 50): Analog Differential Input Pins. Full-scale range (AIN7+ - AIN7-) is REFOUT4 voltage. These pins can be driven from VDD to GND. Exposed Pad (Pin 53): Ground. Solder this pad to ground. CMOS DATA OUTPUT OPTION (CMOS/LVDS = LOW) SDO1 (Pin 27): CMOS Serial Data Output for ADC Channel 1. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN1 on SDO1 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH2, CH3, CH4, CH5, CH6, CH7, CH8). SDO2 (Pin 28): CMOS Serial Data Output for ADC Channel 2. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN2 on SDO2 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH3, CH4, CH5, CH6, CH7, CH8, CH1). 12 SDO3 (Pin 29): CMOS Serial Data Output for ADC Channel 3. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN3 on SDO3 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH4, CH5, CH6, CH7, CH8, CH1, CH2). SDO4 (Pin 30): CMOS Serial Data Output for ADC Channel 4. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN4 on SDO4 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH5, CH6, CH7, CH8, CH1, CH2, CH3). CLKOUT (Pin 33): Serial Data Clock Output. CLKOUT provides a skew-matched clock to latch the SDO output at the receiver (FPGA). The logic level is determined by OVDD. This pin echoes the input at SCK with a small delay. CLKOUTEN (Pin 34): CLKOUT can be disabled by tying Pin 34 to OVDD for a small power savings. If CLKOUT is used, ground this pin. SDO5 (Pin 35): CMOS Serial Data Output for ADC Channel 5. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN5 on SDO5 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH6, CH7, CH8, CH1, CH2, CH3, CH4). SDO6 (Pin 36): CMOS Serial Data Output for ADC Channel 6. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN6 on SDO6 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH7, CH8, CH1, CH2, CH3, CH4, CH5). 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 PIN FUNCTIONS SDO7 (Pin 39): CMOS Serial Data Output for ADC Channel 7. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN7 on SDO7 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH8, CH1, CH2, CH3, CH4, CH5, CH6). SDO8 (Pin 40): CMOS Serial Data Output for ADC Channel 8. The conversion result is shifted MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 16 SCK edges are required for 14-bit conversion data to be read from AIN8 on SDO8 in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH1, CH2, CH3, CH4, CH5, CH6, CH7). SCK (Pin 41): Serial Data Clock Input. The falling edge of this clock shifts the conversion result MSB first onto the SDO pins in SDR mode (DDR = LOW). In DDR mode (SDR/DDR = HIGH) each edge of this clock shifts the conversion result MSB first onto the SDO pins. The logic level is determined by OVDD. DNC (Pin 42): In CMOS mode do not connect this pin. LVDS DATA OUTPUT OPTION (CMOS/LVDS = HIGH OR FLOAT) SDOA+, SDOA- (Pins 27, 28): LVDS Serial Data Output for ADC Channels 1 and 2. The conversion result is shifted CH1 MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 32 SCK edges are required for 14-bit conversion data to be read from AIN1 and AIN2 on SDOA in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH3, CH4, CH5, CH6, CH7, CH8).Terminate with a 100 resistor at the receiver (FPGA). SDOB+, SDOB- (Pins 29, 30): LVDS Serial Data Output for ADC Channels 3 and 4. The conversion result is shifted CH3 MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 32 SCK edges are required for 14-bit conversion data to be read from AIN3 and AIN4 on SDOB in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH5, CH6, CH7, CH8, CH1, CH2).Terminate with a 100 resistor at the receiver (FPGA). CLKOUT+, CLKOUT- (Pins 33, 34): Serial Data Clock Output. CLKOUT provides a skew-matched clock to latch the SDO output at the receiver. These pins echo the input at SCK with a small delay. These pins must be differentially terminated by an external 100 resistor at the receiver (FPGA). SDOC+, SDOC- (Pins 35, 36): LVDS Serial Data Output for ADC channels 5 and 6. The conversion result is shifted CH5 MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 32 SCK edges are required for 14-bit conversion data to be read from AIN5 and AIN6 on SDOA in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH7, CH8, CH1, CH2, CH3, CH4).Terminate with a 100 resistor at the receiver (FPGA). SDOD+, SDOD- (Pins 39, 40): LVDS Serial Data Output for ADC Channels 7 and 8. The conversion result is shifted CH7 MSB first on each falling edge of SCK in SDR mode and each SCK edge in DDR mode. 32 SCK edges are required for 14-bit conversion data to be read from AIN7 and AIN8 on SDOA in SDR mode, 16 SCK edges in DDR mode. Supplying more clocks will yield data from subsequent channels (CH1, CH2, CH3, CH4, CH5, CH6).Terminate with a 100 resistor at the receiver (FPGA). SCK+, SCK- (Pins 41, 42): Serial Data Clock Input. The falling edge of this clock shifts the conversion result MSB first onto the SDO pins in SDR mode (SDR/DDR = LOW). In DDR mode (SDR/DDR = HIGH) each edge of this clock shifts the conversion result MSB first onto the SDO pins. These pins must be differentially terminated by an external 100 resistor at the receiver (ADC). 232014f For more information www.linear.com/LTC2320-14 13 LTC2320-14 FUNCTIONAL BLOCK DIAGRAM CMOS IO Mode VDD (15, 21, 44, 52) 24 CNV 20 19 17 16 AIN1+ AIN1- AIN2+ AIN2- + S/H - 14-BIT+ SIGN SAR ADC MUX + S/H - REF + 14 13 11 10 AIN3 AIN3- AIN4+ AIN4- 42 5 4 2 1 SCK DNC AIN5+ AIN5- AIN6+ AIN6- 51 50 48 47 AIN7 AIN7- AIN8+ AIN8- REF SDO2 SDO3 SDO4 REFOUT2 OUTPUT CLOCK DRIVER CLKOUT CLKOUTEN 27 28 22 29 30 9 33 34 SDR/DDR 23 + S/H - 14-BIT+ SIGN SAR ADC MUX + S/H - 250A x1.7 x3.4 SDO6 SDO6 REFOUT3 14-BIT+ SIGN SAR ADC MUX + S/H - CMOS I/O x1 + S/H - REF 8 CMOS I/O x1 CMOS RECEIVERS REF + SDO1 REFOUT1 14-BIT+ SIGN SAR ADC MUX + S/H - CMOS I/O x1 + S/H - REF 41 GND (3, 7, 12, 18, 26, 32, 38, 46, 49, 53) CMOS I/O x1 1.2V INT REF SDO7 SDO8 REFOUT4 35 36 6 39 40 45 OVDD (31, 37) REFBUFEN 43 CMOS/LVDS 25 232014 BDa 14 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 FUNCTIONAL BLOCK DIAGRAM LVDS IO Mode VDD (15, 21, 44, 52) 24 CNV 20 19 17 16 AIN1+ AIN1- AIN2+ AIN2- + S/H - 14-BIT+ SIGN SAR ADC MUX + S/H - REF 14 13 11 10 AIN3+ AIN3- AIN4+ AIN4- 42 5 4 2 1 SCK+ SCK- LVDS RECEIVERS AIN5+ + S/H - AIN5- AIN6+ AIN6- 50 48 47 AIN7+ AIN7- AIN8+ AIN8- REF SDOA- SDOB+ SDOB- REFOUT2 x1 CLKOUT+ CLKOUT- 27 28 22 29 30 9 33 34 SDR/DDR 23 14-BIT+ SIGN SAR ADC MUX + S/H - 250A x1.7 x3.4 SDOC+ SDOC- REFOUT3 14-BIT+ SIGN SAR ADC MUX + S/H - LVDS I/O x1 + S/H - REF 8 LVDS I/O OUTPUT CLOCK DRIVER REF 51 SDOA+ REFOUT1 14-BIT+ SIGN SAR ADC MUX + S/H - LVDS I/O x1 + S/H - REF 41 GND (3, 7, 12, 18, 26, 32, 38, 46, 49, 53) LVDS I/O x1 1.2V INT REF SDOD+ SDOD- REFOUT4 35 36 6 39 40 45 OVDD (31, 37) REFBUFEN 43 CMOS/LVDS 25 232014 BDb 232014f For more information www.linear.com/LTC2320-14 15 LTC2320-14 TIMING DIAGRAM SDR Mode, CMOS (Reading 1 Channel per SDO) SAMPLE N CNV SAMPLE N+1 CONVERT ACQUIRE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK CLKOUT SDO1 Hi-Z Hi-Z Hi-Z DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 D14 CHANNEL 1 CONVERSION N SDO8 Hi-Z DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 Hi-Z CHANNEL 2 CONVERSION N D5 D4 D3 D2 D1 D0 0 D14 CHANNEL 8 CONVERSION N Hi-Z CHANNEL 1 CONVERSION N 232014 TD01 DDR Mode, CMOS (Reading 1 Channel per SDO) SAMPLE N CNV SAMPLE N+1 CONVERT ACQUIRE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SCK CLKOUT SDO1 Hi-Z Hi-Z Hi-Z DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 CHANNEL 1 CONVERSION N SDO8 Hi-Z DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D14 Hi-Z CHANNEL 2 CONVERSION N D4 D3 CHANNEL 8 CONVERSION N D2 D1 D0 D14 Hi-Z CHANNEL 1 CONVERSION N 232014 TD02 16 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 TIMING DIAGRAM SDR Mode, LVDS (Reading 2 Channels per SDO Pair) SAMPLE N CNV SAMPLE N+1 CONVERT ACQUIRE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 17 18 19 20 21 22 23 24 25 D14 D13 D12 D11 D10 D9 D8 D7 D6 26 27 28 29 30 31 32 SCK CLKOUT SDOA DONT CARE D14 CHANNEL 1 CONVERSION N SDOD DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D5 D4 D3 D2 D1 D0 0 D14 CHANNEL 2 CONVERSION N D4 D3 D2 D1 D0 0 D14 D13 D12 D11 D10 D9 D8 CHANNEL 7 CONVERSION N D7 D6 D5 CHANNEL 3 CONVERSION N D4 D3 D2 D1 D0 0 D14 CHANNEL 8 CONVERSION N CHANNEL 1 CONVERSION N 232014 TD03 DDR Mode, LVDS (Reading 2 Channels per SDO Pair) SAMPLE N CNV SAMPLE N+1 ACQUIRE CONVERT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 17 18 19 20 21 22 23 24 25 D7 D6 26 27 28 29 30 31 32 SCK CLKOUT SDOA DONT CARE D14 D13 D12 D11 D10 D9 D8 CHANNEL 1 CONVERSION N SDOD DONT CARE D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D5 D4 D3 D2 D1 D0 0 D14 CHANNEL 2 CONVERSION N D4 D3 D2 D1 D0 0 D14 D13 D12 D11 D10 D9 CHANNEL 7 CONVERSION N D8 D7 D6 D5 CHANNEL 8 CONVERSION N CHANNEL 3 CONVERSION N D4 D3 D2 D1 D0 0 D14 CHANNEL 1 CONVERSION N 232014 TD04 232014f For more information www.linear.com/LTC2320-14 17 LTC2320-14 APPLICATIONS INFORMATION The LTC2320-14 is a low noise, high speed 14-bit successive approximation register (SAR) ADC with differential inputs and a wide input common mode range. Operating from a single 3.3V or 5V supply, the LTC2320-14 has a 4VP-P or 8VP-P differential input range, making it ideal for applications which require a wide dynamic range. The LTC2320-14 achieves 1LSB INL typical, no missing codes at 14 bits and 81dB SNR. The LTC2320-14 has an onboard reference buffer and low drift (20ppm/C max) 4.096V temperature-compensated reference. The LTC2320-14 also has a high speed SPIcompatible serial interface that supports CMOS or LVDS. The fast 1.5Msps per channel throughput with one-cycle latency makes the LTC2320-14 ideally suited for a wide variety of high speed applications. The LTC2320-14 dissipates only 20mW per channel. Nap and sleep modes are also provided to reduce the power consumption of the LTC2320-14 during inactive periods for further power savings. complement format. When driven by fully differential inputs, the transfer function spans 215 codes. When driven by pseudo differential inputs, the transfer function spans 214 codes. Table 1: Code Ranges for the Analog Input Operational Modes MODE Span (VIN+ - VIN-) Min Code Fully Differential -REFOUT to +REFOUT Pseudo-Differential 0 to REFOUT Unipolar 000 0000 0000 011 1111 1111 0000 1111 011 1111 1111 1111 011 1111 1111 1110 000 0000 0000 0001 000 0000 0000 0000 111 1111 1111 1111 100 0000 0000 0001 100 0000 0000 0000 -REFOUT/2 TRANSFER FUNCTION The LTC2320-14 digitizes the full-scale voltage of 2 * REFOUT into 215 levels, resulting in a 15-bit resolution size of 250V with REFBUF = 4.096V. The ideal transfer function is shown in Figure 2. The output data is in 2's 18 100 0000 0000 011 1111 1111 0000 1111 110 0000 0000 001 1111 1111 0000 1111 CONVERTER OPERATION The LTC2320-14 operates in two phases. During the acquisition phase, the sample capacitor is connected to the analog input pins AIN+ and AIN - to sample the differential analog input voltage, as shown in Figure 3. A falling edge on the CNV pin initiates a conversion. During the conversion phase, the 14-bit CDAC is sequenced through a successive approximation algorithm effectively comparing the sampled input with binary-weighted fractions of the reference voltage (e.g., VREFOUT/2, VREFOUT/4 ... VREFOUT/32768) using a differential comparator. At the end of conversion, a CDAC output approximates the sampled analog input. The ADC control logic then prepares the 14-bit digital output code for serial transfer. Max Code Pseudo-Differential -REFOUT/2 to Bipolar +REFOUT/2 OUTPUT CODE (TWO'S COMPLEMENT) OVERVIEW 1LSB = 2 * REFOUT 32768 -1 0 1 LSB LSB INPUT VOLTAGE (V) REFOUT/2 -1LSB 232014 F02 Figure 2. LTC2320-14 Transfer Function Analog Input The differential inputs of the LTC2320-14 provide great flexibility to convert a wide variety of analog signals with no configuration required. The LTC2320-14 digitizes the difference voltage between the AIN+ and AIN - pins while supporting a wide common mode input range. The analog input signals can have an arbitrary relationship to each other, provided that they remain between VDD and GND. The LTC2320-14 can also digitize more limited classes of analog input signals such as pseudo-differential unipolar/ bipolar and fully differential with no configuration required. The analog inputs of the LTC2320-14 can be modeled by the equivalent circuit shown in Figure 3. The backto-back diodes at the inputs form clamps that provide ESD protection. In the acquisition phase, 10pF (CIN) from the sampling capacitor in series with approximately 15 (RON) from the on-resistance of the sampling switch 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION mode input range relaxes the accuracy requirements of any signal conditioning circuits prior to the analog inputs. VDD RON 15 AIN+ CIN 10pF Pseudo-Differential Bipolar Input Range BIAS VOLTAGE VDD RON 15 AIN- CIN 10pF 232014 F03 Figure 3. The Equivalent Circuit for the Differential Analog Input of the LTC2320-14 is connected to the input. Any unwanted signal that is common to both inputs will be reduced by the common mode rejection of the ADC sampler. The inputs of the ADC core draw a small current spike while charging the CIN capacitors during acquisition. Single-Ended Signals Single-ended signals can be directly digitized by the LTC2320-14. These signals should be sensed pseudodifferentially for improved common mode rejection. By connecting the reference signal (e.g., ground sense) of the main analog signal to the other AIN pin, any noise or disturbance common to the two signals will be rejected by the high CMRR of the ADC. The LTC2320-14 flexibility handles both pseudo-differential unipolar and bipolar signals, with no configuration required. The wide common VREF 0V LT1819 VREF + - 0V The pseudo-differential bipolar configuration represents driving one of the analog inputs at a fixed voltage, typically VREF /2, and applying a signal to the other AIN pin. In this case the analog input swings symmetrically around the fixed input yielding bipolar two's complement output codes with an ADC span of half of full-scale. This configuration is illustrated in Figure 4, and the corresponding transfer function in Figure 5. The fixed analog input pin need not be set at VREF /2, but at some point within the VDD rails allowing the alternate input to swing symmetrically around this voltage. If the input signal (AIN+ - AIN -) swings beyond REFOUT1,2,3,4/2, valid codes will be generated by the ADC and must be clamped by the user, if necessary. Pseudo-Differential Unipolar Input Range The pseudo-differential unipolar configuration represents driving one of the analog inputs at ground and applying a signal to the other AIN pin. In this case, the analog input swings between ground and VREF yielding unipolar two's complement output codes with an ADC span of half of full-scale. This configuration is illustrated in Figure 6, and the corresponding transfer function in Figure 7. If the input signal (AIN+ - AIN -) swings negative, valid codes will be generated by the ADC and must be clamped by the user, if necessary. LTC2320-14 25 AIN1+ REFOUT1 VREF REF 220pF 10k VREF /2 10k 1F + - VREF /2 25 AIN1- SDO1 CLKOUT SCK ONLY CHANNEL 1 SHOWN FOR CLARITY 10F 1F TO CONTROL LOGIC (FPGA, CPLD, DSP, ETC.) 232014 F04 Figure 4. Pseudo-Differential Bipolar Application Circuit 232014f For more information www.linear.com/LTC2320-14 19 LTC2320-14 APPLICATIONS INFORMATION ADC CODE (2's COMPLEMENT) 16383 8191 -VREF -VREF /2 0 VREF /2 AIN (AIN+ - AIN-) VREF DOTTED REGIONS AVAILABLE -8192 232014 F05 -16384 Figure 5. Pseudo-Differential Bipolar Transfer Function VREF 0V LT1818 VREF + - 0V LTC2320-14 25 AIN1+ REF 220pF 25 REFOUT1 AIN1- SDO1 CLKOUT SCK 10F 1F TO CONTROL LOGIC (FPGA, CPLD, DSP, ETC.) 232014 F06 Figure 6. Pseudo-Differential Unipolar Application Circuit ADC CODE (2's COMPLEMENT) 16383 8191 -VREF -VREF /2 -8192 -16384 0 VREF /2 VREF AIN (AIN+ - AIN-) DOTTED REGIONS AVAILABLE 232014 F07 Figure 7. Pseudo-Differential Unipolar Transfer Function 20 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION Single-Ended-to-Differential Conversion While single-ended signals can be directly digitized as previously discussed, single-ended to differential conversion circuits may also be used when higher dynamic range is desired. By producing a differential signal at the inputs of the LTC2320-14, the signal swing presented to the ADC is maximized, thus increasing the achievable SNR. REFOUT1,2,3,4. The common mode input voltage can span the entire supply range up to VDD, limited by the input signal swing. The fully-differential configuration is illustrated in Figure 10, with the corresponding transfer function illustrated in Figure 11. INPUT DRIVE CIRCUITS The LT(R)1819 high speed dual operational amplifier is recommended for performing single-ended-to-differential conversions, as shown in Figure 8. In this case, the first amplifier is configured as a unity-gain buffer and the single-ended input signal directly drives the high impedance input of this amplifier. A low impedance source can directly drive the high impedance inputs of the LTC2320-14 without gain error. A high impedance source should be buffered to minimize settling time during acquisition and to optimize the distortion performance of the ADC. Minimizing settling time is important even for DC inputs, because the ADC inputs draw a current spike during acquisition. Fully-Differential Inputs For best performance, a buffer amplifier should be used to drive the analog inputs of the LTC2320-14. The amplifier provides low output impedance to minimize gain error and allows for fast settling of the analog signal during the acquisition phase. It also provides isolation between the signal source and the ADC inputs, which draw a small current spike during acquisition. To achieve the best distortion performance of the LTC232014, we recommend driving a fully-differential signal through LT1819 amplifiers configured as two unity-gain buffers, as shown in Figure 9. This circuit achieves the full data sheet THD specification of -90dB at input frequencies up to 500kHz. A fully-differential input signal can span the maximum full-scale of the ADC, up to VREF 0V 200 VREF /2 VREF LT1819 + - VREF + - VREF 200 0V 0V VREF 0V 0V LT1819 + - VREF + - VREF 0V 0V 232014 F09 232014 F08 Figure 8. Single-Ended to Differential Driver Figure 9. LT1819 Buffering a Fully-Differential Signal Source 232014f For more information www.linear.com/LTC2320-14 21 LTC2320-14 APPLICATIONS INFORMATION VREF 0V LT1819 VREF + - 0V LTC2320-14 25 AIN1+ REFOUT1 REF 220pF VREF 0V VREF + - 0V 25 AIN1- SDO1 CLKOUT SCK ONLY CHANNEL 1 SHOWN FOR CLARITY 10F 1F TO CONTROL LOGIC (FPGA, CPLD, DSP, ETC.) 232014 F10 Figure 10. Fully-Differential Application Circuit ADC CODE (2's COMPLEMENT) 16383 8192 -VREF -VREF /2 0 VREF /2 VREF AIN (AINn + - AINn -) -8192 -16384 232014 F11 Figure 11. Fully-Differential Transfer Function 22 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION Input Filtering ADC REFERENCE The noise and distortion of the buffer amplifier and signal source must be considered since they add to the ADC noise and distortion. Noisy input signals should be filtered prior to the buffer amplifier input with a low bandwidth filter to minimize noise. The simple 1-pole RC lowpass filter shown in Figure 12 is sufficient for many applications. The sampling switch on-resistance (RON) and the sample capacitor (CIN) form a second lowpass filter that limits the input bandwidth to the ADC core to 110MHz. A buffer amplifier with a low noise density must be selected to minimize the degradation of the SNR over this bandwidth. High quality capacitors and resistors should be used in the RC filters since these components can add distortion. NPO and silver mica type dielectric capacitors have excellent linearity. Carbon surface mount resistors can generate distortion from self heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to both problems. SINGLE-ENDED INPUT SIGNAL Internal Reference The LTC2320-14 has an on-chip, low noise, low drift (20ppm/C max), temperature compensated bandgap reference. It is internally buffered and is available at REF (Pin 8). The reference buffer gains the internal reference voltage to 4.096V for supply voltages VDD = 5V and to 2.048V for VDD = 3.3V. The REF pin also drives the four internal reference buffers with a current limited output (250A) so it may be easily overdriven with an external reference in the range of 1.25V to 5V. Bypass REF to GND with a 1F (X5R, 0805 size) ceramic capacitor to compensate the reference buffer and minimize noise. The 1F capacitor should be as close as possible to the LTC2320-14 package to minimize wiring inductance. The voltage on the REF pin must be externally buffered if used for external circuitry. IN+ 50 IN- 3.3nF BW = 1MHz LTC2320 SINGLE-ENDED TO DIFFERENTIAL DRIVER 232014 F12 Figure 12. Input Signal Chain Table 2. Reference Configurations and Ranges REFERENCE CONFIGURATION VDD Internal Reference with Internal Buffers Common External Reference with Internal Buffer (REF Pin Externally Overdriven) External Reference with REF Buffers Disabled REFBUFEN REF PIN REFOUT1,2,3,4 PIN DIFFERENTIAL INPUT RANGE PIN 5V 5V 4.096V 4.096V 4.096V 3.3V 3.3V 2.048V 2.048V 2.048V 5V 5V 1.25V to 5V 1.25V to 3.3V 1.25V to 5V 3.3V 3.3V 1.25V to 5V 1.25V to 3.3V 1.25V to 3.3V 5V 0V 4.096V 1.25V to 5V 1.25V to 5V 3.3V 0V 2.048V 1.25V to 3.3V 1.25V to 3.3V 232014f For more information www.linear.com/LTC2320-14 23 LTC2320-14 APPLICATIONS INFORMATION External Reference The internal REFOUT1,2,3,4 buffers can also be overdriven from 1.25V to 5V with an external reference at REFOUT1,2,3,4 as shown in Figure 13 (c). To do so, REFBUFEN must be grounded to disable the REF buffers. A 55k internal resistance loads the REFOUT1,2,3,4 pins when the REF buffers are disabled. To maximize the input signal swing and corresponding SNR, the LTC6655-5 is VDD 3.3V TO 5V REF LTC2320-14 REFOUT1 10F LTC6655-4.096 REFBUFEN VIN SHDN REF VOUT_F VOUT_S 10F LTC2320-14 10F 0.1F REFOUT1 10F REFOUT2 10F VDD +5V 5V TO 13.2V REFBUFEN 1F recommended when overdriving REFOUT. The LTC6655-5 offers the same small size, accuracy, drift and extended temperature range as the LTC6655-4.096. By using a 5V reference, a higher SNR can be achieved. We recommend bypassing the LTC6655-5 with a 10F ceramic capacitor (X5R, 0805 size) close to each of the REFOUT1,2,3,4 pins. If the REF pin voltage is used as a REFOUT reference when REFBUFEN is connected to GND, it should be buffered externally. REFOUT2 10F REFOUT3 REFOUT3 10F REFOUT4 10F GND 10F 232014 F13a REFOUT4 GND 232014 F13b (13a) LTC2320-14 Internal Reference Circuit (13b) LTC2320-14 with a Shared External Reference Circuit +5V VDD REFBUFEN REF 1F 5V TO 13.2V LTC6655-4.096 VIN VOUT_F SHDN VOUT_S REFOUT1 10F 0.1F 5V TO 13.2V LTC2320-14 LTC6655-2.048 VIN VOUT_F SHDN VOUT_S REFOUT2 10F 0.1F 5V TO 13.2V LTC6655-2.5 VIN VOUT_F SHDN VOUT_S REFOUT3 10F 0.1F 5V TO 13.2V LTC6655-3 VIN VOUT_F SHDN VOUT_S REFOUT4 10F 0.1F GND 232014 F13c (13c) LTC2320-14 with Different External Reference Voltages Figure 13. Reference Connections 24 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION Internal Reference Buffer Transient Response DYNAMIC PERFORMANCE The REFOUT1,2,3,4 pins of the LTC2320-14 draw charge (QCONV) from the external bypass capacitors during each conversion cycle. If the internal reference buffer is overdriven, the external reference must provide all of this charge with a DC current equivalent to IREF = QCONV/tCYC. Thus, the DC current draw of IREFOUT1,2,3,4 depends on the sampling rate and output code. In applications where a burst of samples is taken after idling for long periods, as shown in Figure 14 , IREFBUF quickly goes from approximately ~75A to a maximum of 500A for REFOUT = 5V at 1.5Msps. This step in DC current draw triggers a transient response in the external reference that must be considered since any deviation in the voltage at REFOUT will affect the accuracy of the output code. Due to the one-cycle conversion latency, the first conversion result at the beginning of a burst sampling period will be invalid. If an external reference is used to overdrive REFOUT1,2,3,4, the fast settling LTC6655 reference is recommended. Fast Fourier transform (FFT) techniques are used to test the ADC's frequency response, distortion and noise at the rated throughput. By applying a low distortion sine wave and analyzing the digital output using an FFT algorithm, the ADC's spectral content can be examined for frequencies outside the fundamental. The LTC2320-14 provides guaranteed tested limits for both AC distortion and noise measurements. CNV IDLE PERIOD 232014 F14 Figure 14. CNV Waveform Showing Burst Sampling 16384 Signal-to-Noise and Distortion Ratio (SINAD) The signal-to-noise and distortion ratio (SINAD) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the A/D output. The output is bandlimited to frequencies from above DC and below half the sampling frequency. Figure 16 shows that the LTC2320-14 achieves a typical SINAD of 80dB at a 1.5MHz sampling rate with a 500kHz input. Signal-to-Noise Ratio (SNR) The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components except the first five harmonics and DC. Figure 16 shows that the LTC2320-14 achieves a typical SNR of 81dB at a 1.5MHz sampling rate with a 500kHz input. SMPL 0 8192 4.096V RANGE 4096 0 IN+ = 1.5MHz SQUARE WAVE IN- = 0V -4096 -20 -10 0 10 20 30 40 50 60 70 80 90 SETTLING TIME (ns) 232014 F15 AMPLITUDE (dBFS) OUTPUT CODE (LSB) 12288 IN SNR = 81.1dB THD = -90.2dB -20 SINAD = 80.8dB SFDR = 94.7dB -40 -60 -80 -100 -120 -140 Figure 15. Transient Response of the LTC2320-14 0 0.1 0.2 0.3 0.4 0.5 FREQUENCY (MHz) 0.6 0.7 232014 F16 Figure 16. 32k Point FFT of the LTC2320-14 232014f For more information www.linear.com/LTC2320-14 25 LTC2320-14 APPLICATIONS INFORMATION Total Harmonic Distortion (THD) Total harmonic distortion (THD) is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency (fSMPL /2). THD is expressed as: THD=20log V22 + V32 + V42 + ...+VN 2 V1 TIMING AND CONTROL where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second through Nth harmonics. POWER CONSIDERATIONS The LTC2320-14 requires two power supplies: the 3.3V to 5V power supply (VDD), and the digital input/output interface power supply (OVDD). The flexible OVDD supply allows the LTC2320-14 to communicate with any digital logic operating between 1.8V and 2.5V. When using LVDS I/O, the OVDD supply must be set to 2.5V. Power Supply Sequencing The LTC2320-14 does not have any specific power supply sequencing requirements. Care should be taken to adhere to the maximum voltage relationships described in the Absolute Maximum Ratings section. The LTC232014 has a power-on-reset (POR) circuit that will reset the LTC2320-14 at initial power-up or whenever the power 33 SUPPLY CURRENT (mA) 31 29 VDD = 5V 27 VDD = 3.3V 23 21 0 0.3 0.6 0.9 1.2 SAMPLE FREQUENCY (Msps) 1.5 232014 F17 Figure 17. Power Supply Current of the LTC2320-14 Versus Sampling Rate 26 CNV Timing The LTC2320-14 sampling and conversion is controlled by CNV. A rising edge on CNV will start sampling and the falling edge starts the conversion and readout process. The conversion process is timed by the SCK input clock. For optimum performance, CNV should be driven by a clean low jitter signal. The Typical Application at the back of the data sheet illustrates a recommended implementation to reduce the relatively large jitter from an FPGA CNV pulse source. Note the low jitter input clock times the falling edge of the CNV signal. The rising edge jitter of CNV is much less critical to performance. The typical pulse width of the CNV signal is 30ns with < 1.5ns rise and fall times at a 1.5Msps conversion rate. SCK Serial Data Clock Input In SDR mode (SDR/DDR Pin 23 = GND), the falling edge of this clock shifts the conversion result MSB first onto the SDO pins. A 100MHz external clock must be applied at the SCK pin to achieve 1.5Msps throughput using all eight SDO outputs. In DDR mode (SDR/DDR Pin 23 = OVDD), each input edge of SCK shifts the conversion result MSB first onto the SDO pins. A 50MHz external clock must be applied at the SCK pin to achieve 1.5Msps throughput using all eight SDO1 through SDO8 outputs. CLKOUT Serial Data Clock Output 25 19 supply voltage drops below 2V. Once the supply voltage re-enters the nominal supply voltage range, the POR will reinitialize the ADC. No conversions should be initiated until 10ms after a POR event to ensure the reinitialization period has ended. Any conversions initiated before this time will produce invalid results. The CLKOUT output provides a skew-matched clock to latch the SDO output at the receiver. The timing skew of the CLKOUT and SDO outputs are matched. For high throughput applications, using CLKOUT instead of SCK to capture the SDO output eases timing requirements at the receiver. For low throughput speed applications, CLKOUT can be disabled by tying Pin 34 to OVDD. 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION Nap/Sleep Modes Nap mode is a method to save power without sacrificing power-up delays for subsequent conversions. Sleep mode has substantial power savings, but a power-up delay is incurred to allow the reference and power systems to become valid. To enter nap mode on the LTC2320-14, the SCK signal must be held high or low and a series of two CNV pulses must be applied. This is the case for both CMOS and LVDS modes. The second rising edge of CNV initiates the nap state. The nap state will persist until either a single rising edge of SCK is applied, or further CNV pulses are applied. The SCK rising edge will put the LTC2320-14 back into the operational (full-power) state. When in nap mode, two additional pulses will put the LTC2320-14 in sleep mode. When configured for CMOS I/O operation, a single rising edge of SCK can return the LTC2320-14 into operational mode. A 10ms delay is necessary after exiting sleep mode to allow the reference buffer to recharge the external filter capacitor. In LVDS mode, exit sleep mode by supplying a fifth CNV pulse. The fifth pulse will return the LTC2320-14 to operational mode, and further SCK pulses will keep the part from re-entering nap and sleep modes. The fifth SCK pulse also works in CMOS mode as a method to exit sleep. In the absence of SCK pulses, repetitive CNV pulses will cycle the LTC2320-14 between operational, nap and sleep modes indefinitely. Refer to the timing diagrams in Figure 18, Figure 19, Figure 20 and Figure 21 for more detailed timing information about sleep and nap modes. DIGITAL INTERFACE The LTC2320-14 features a serial digital interface that is simple and straightforward to use. The flexible OVDD supply allows the LTC2320-14 to communicate with any digital logic operating between 1.8V and 2.5V. In addition to a standard CMOS SPI interface, the LTC2320-14 provides an optional LVDS SPI interface to support low noise digital design. The CMOS /LVDS pin is used to select the digital interface mode. The SCK input clock shifts the conversion result MSB first on the SDO pins. CLKOUT provides a skew-matched clock to latch the SDO output at the receiver. The timing skew of the CLKOUT and SDO outputs are matched. For high throughput applications, using CLKOUT instead of SCK to capture the SDO output eases timing requirements at the receiver. In CMOS mode, use the SDO1 - SDO8, and CLKOUT pins as outputs. Use the SCK pin as an input. In LVDS mode, use the SDOA+/ SDOA- through SDOD+/SDOD- and CLKOUT+/CLKOUT- pins as differential outputs. Each LVDS lane yields two channels worth of data: SDOA yields CH1 and CH2 data, SDOB yields CH3 and CH4 data, SDOC yields CH5 and CH6 data and SDOD yields CH7 and CH8 data. These pins must be differentially terminated by an external 100 resistor at the receiver (FPGA). The SCK+/SCK- pins are differential inputs and must be terminated differentially by an external 100 resistor at the receiver(ADC). SDR/DDR Modes The LTC2320-14 has an SDR (single data rate) and DDR (double data rate) mode for reading conversion data from the SDO pins. In both modes, CLKOUT is a delayed version of SCK. In SDR mode, each negative edge of SCK shifts the conversion data out the SDO pins. In DDR mode, each edge of the SCK input shifts the conversion data out. In DDR mode, the required SCK frequency is half of what is required in SDR mode. Tie SDR/DDR to ground to configure for SDR mode and to OVDD for DDR mode. The CLKOUT signal is a delayed version of the SCK input and is phase aligned with the SDO data. In SDR mode, the SDO transitions on the falling edge of CLKOUT as illustrated in Figure 21. We recommend using the rising edge of CLKOUT to latch the SDO data into the FPGA register in SDR mode. In DDR mode, The SDO transitions on each input edge of SCK. We recommend using the CLKOUT rising and falling edges to latch the SDO data into the FPGA registers in DDR mode. Since CLKOUT and SDO data is phase aligned, the SDO signals will need to be digitally delayed in the FPGA to provide adequate setup and hold timing margins in DDR mode. 232014f For more information www.linear.com/LTC2320-14 27 LTC2320-14 APPLICATIONS INFORMATION CNV 1 2 FULL POWER MODE NAP MODE SCK HOLD STATIC HIGH OR LOW WAKE ON 1ST SCK EDGE SDO1 - 8 Z Z 232014 F18 Figure 18. CMOS and LVDS Mode NAP and WAKE Using SCK REFOUT1 - 4 REFOUT RECOVERY 4.096V 4.096V tWAKE CNV 1 2 3 4 NAP MODE SCK SLEEP MODE FULL POWER MODE HOLD STATIC HIGH OR LOW WAKE ON 1ST SCK EDGE SDO1 - 8 Z Z Z Z 232014 F19 Figure 19. CMOS Mode SLEEP and WAKE Using SCK REFOUT1 - 4 REFOUT RECOVERY 4.096V 4.096V tWAKE CNV 1 2 3 4 NAP MODE SCK WAKE ON 5TH CNV EDGE 5 SLEEP MODE FULL POWER MODE HOLD STATIC HIGH OR LOW SDO1 - 8 Z Z Z Z Z 232014 F20 Figure 20. LVDS and CMOS Mode SLEEP and WAKE Using CNV SDR MODE TIMING DDR MODE TIMING tCYC tCNVH tCYC tCONV tREADOUT tCNVH tDSCKCNVH CNV 1 2 3 tREADOUT tDSCKCNVH tSCKH tSCK SCK tCONV CNV tSCKH tSCK 14 15 SCK 16 1 2 3 1 2 3 14 15 CLKOUT 16 1 tDSCKCLKOUT SDO HI-Z D15 D14 D13 D2 D1 D0 D15 3 tDCNVSDOV HI-Z SDO HI-Z Figure 21. LTC2320-14 Timing Diagram 28 2 14 tDSCKCLKOUT tDCNVSDOZ tHSDO tDCNVSDOV 15 16 tSCKL tSCKL CLKOUT 14 D14 D13 D2 16 tDCNVSDOZ tHSDO D15 15 D1 D0 D15 HI-Z 232014 F21 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 APPLICATIONS INFORMATION Multiple Data Lanes The LTC2320-14 has up to eight SDO data lanes in CMOS mode and four SDO lanes in LVDS mode. In CMOS mode, the number of possible data lanes range from eight (SDO1 - SDO8), four (SDO1, SDO3, SDO5 and SDO7), two (SDO1 and SDO5) and one (SDO1). Generally, the more data lanes used, the lower the required SCK frequency. When using less than eight lanes in CMOS mode, there is a limit on the maximum possible conversion frequency (see Table 3). Each SDO pin will hold the MSB of the conversion data. In DDR mode you can use a SCK frequency half of SDR mode. See Table 3 for examples of various possibilities and the resulting SCK frequency required. Multiple Data Lanes The LTC2320-14 has up to eight serial data output data lanes in CMOS mode and four serial data output lane pairs in LVDS mode. The data on each lane consists of 14-bit conversion results presented MSB first. CMOS In CMOS mode, the number of possible data lanes range from eight (SDO1 - SDO8), four (SDO1, SDO3, SDO5 and SDO7), two (SDO1 and SDO5) and one (SDO1). As suggested in the CMOS Timing Diagrams, each SDO lane outputs the conversion results for all analog input channels LTC2320-14 2.5V 2.5V CMOS/LVDS Applications that cannot accommodate the full eight lanes of serial data may employ fewer lanes without reconfiguring the LTC2320-14. For example, capturing the first two conversion results (32 SCK cycles total in SDR mode and 32 SCK edges in DDR mode) from SDO1, SDO3, SDO5, and SDO7 provides data for analog input channels 1 and 2, 3 and 4, 5 and 6, and 7 and 8, respectively, using four output lanes. Similarly, capturing the first four conversion results (64 SCK cycles total in SDR mode and 64 SCK edges in DDR mode) from SDO1 and SDO5 provides data for analog input channels 1 to 4 and 5 to 8, respectively, using two output lanes. If only one lane can be accommodated, capturing the first eight conversion results (128 SCK cycles total in SDR mode and 128 SCK edges in DDR mode) from SDO1 provides data for all analog input channels. Generally, the more data lanes used, the lower the required SCK frequency. When using less than eight lanes in CMOS mode, there is a limit on the maximum possible conversion frequency. FPGA OR DSP OVDD SCK+ SCK- in a sequential circular manner. For example, the first conversion result on SDO1 corresponds to analog input channel 1, followed by the conversion results for channels 2 through 8. The data output on SDO1 then wraps back to channel 1 and this pattern repeats indefinitely. Other SDO lanes follow a similar circular pattern except the first conversion result presented on each lane corresponds to its associated analog input channel. LTC2320-14 + - 100 2.5V OVDD SCK+ SCK- SDOD+ SDOD- 100 + - SDOC+ SDOC- 100 + - CLKOUT+ CLKOUT - 100 + - SDOB+ SDOB- 100 + - SDOB+ SDOB- SDOA+ SDOA- 100 + - SDOA+ SDOA- CNV FPGA OR DSP + - 100 SDOD+ SDOD- SDOC+ SDOC- 2.5V CMOS/LVDS RETIMING FLIP-FLOP CLKOUT+ CLKOUT - CNV 232014 F22 Figure 22. LTC2320-14 Using the LVDS Interface 100 + - 100 + - RETIMING FLIP-FLOP 232014 F23 Figure 23. LTC2320-14 Using the LVDS Interface with One Lane 232014f For more information www.linear.com/LTC2320-14 29 LTC2320-14 APPLICATIONS INFORMATION See Table 3 for examples of various possibilities and the resulting SCK frequency required. conversion results (128 SCK cycles total in SDR mode and 128 SCK edges in DDR mode) from SDOA provides data for all analog input channels. Generally, the more data lanes used, the lower the required SCK frequency. When using less than four lanes in LVDS mode, there is a limit on the maximum possible conversion frequency. See Table 3 for examples of various possibilities and the resulting SCK frequency required. LVDS In LVDS mode, the number of possible data lane pairs range from four (SDOA - SDOD), two (SDOA and SDOC) and one (SDOA). As suggested in the LVDS Timing Diagrams, each SDO lane pair outputs the conversion results for all analog input channels in a sequential circular manner. For example, the first conversion result on SDOA corresponds to analog input channel pair 1 and 2, followed by the conversion results for channels 3 through 8. The data output on SDOA then wraps back to channel 1 and this pattern repeats indefinitely. Other SDO lanes follow a similar circular pattern except the first conversion result presented on each lane corresponds to its associated analog input channel pairs (SDOA: analog inputs 1 and 2, SDOB: analog inputs 3 and 4, SDOC: analog inputs 5 and 6 and SDOD: analog inputs 7 and 8). BOARD LAYOUT To obtain the best performance from the LTC2320-14, a printed circuit board is recommended. Layout for the printed circuit board (PCB) should ensure the digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital clocks or signals adjacent to analog signals or underneath the ADC. Supply bypass capacitors should be placed as close as possible to the supply pins. Low impedance common returns for these bypass capacitors are essential to the low noise operation of the ADC. A single solid ground plane is recommended for this purpose. When possible, screen the analog input traces using ground. Applications that cannot accommodate the full four lanes of serial data may employ fewer lanes without reconfiguring the LTC2320-14. For example, capturing the first four conversion results (64 SCK cycles total in SDR mode and 64 SCK edges in DDR mode) from SDOA and SDOC provides data for analog input channels 1 through 4, and 5 through 8, respectively, using two output lanes. If only one lane can be accommodated, capturing the first eight Recommended Layout For a detailed look at the reference design for this converter, including schematics and PCB layout, please refer to DC2395A, the evaluation kit for the LTC2320-14. Table 3. Conversion Frequency for Various I/O Modes I/O MODE CMOS CMOS/ LVDS PIN GND (CMOS) SDR/ DDR PIN GND (SDR) OVDD (DDR) OVDD (DDR) SDO1 - 8 LANES SDO1 - SDO8 SDO1 - SDO8 SDO1, SDO3, SDO5, SDO7 SDO1 SDOA - D LANES SCK FREQ (MHz) 100 50 CLKOUT FREQ (MHz) 100 50 SCK CYCLES 16 8 50 50 16 100 200 100 150 300 100 200 100 150 300 128 32 16 32 128 GND (SDR) GND (SDR) SDOA - SDOD OV (DDR) SDOA - SDOD OVDD DD LVDS (LVDS) SDOA, SDOC OVDD (DDR) GND (SDR) SDOA Notes: Conversion Period (SDR) = tCNV_MIN + tCONV_MAX + (128/(Lanes * fSCK)) Conversion Period (DDR) = tCNV_MIN + tCONV_MAX + (64/(Lanes * fSCK)) Conversion Frequency = 1/Conversion Period SCK Cycles (SDR) = 128/Lanes SCK Cycles (DDR) = 64/Lanes 30 OVDD 1.8V to 2.5V 2.5V CONVERSION FREQUENCY (Msps/CH) 1.5 1.5 1.25 0.5 1.5 1.5 1.4 1.0 232014f For more information www.linear.com/LTC2320-14 LTC2320-14 PACKAGE DESCRIPTION Please refer to http://www.linear.com/product/LTC2320-14#packaging for the most recent package drawings. UKG Package 52-Lead Plastic QFN (7mm x 8mm) (Reference LTC DWG # 05-08-1729 Rev O) 7.50 0.05 6.10 0.05 5.50 REF (2 SIDES) 0.70 0.05 6.45 0.05 6.50 REF 7.10 0.05 8.50 0.05 (2 SIDES) 5.41 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 7.00 0.10 (2 SIDES) 0.75 0.05 0.00 - 0.05 R = 0.115 TYP 5.50 REF (2 SIDES) 51 52 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45C CHAMFER 8.00 0.10 (2 SIDES) 6.50 REF (2 SIDES) 6.45 0.10 5.41 0.10 R = 0.10 TYP TOP VIEW 0.200 REF 0.00 - 0.05 0.75 0.05 (UKG52) QFN REV O 0306 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD SIDE VIEW NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTC2320-14 232014f 31 LTC2320-14 TYPICAL APPLICATION Low Jitter Clock Timing with RF Sine Generator Using Clock Squaring/Level-Shifting Circuit and Retiming Flip-Flop VCC 0.1F 50 1k NC7SVUO4P5X MASTER_CLOCK VCC 1k D PRE NC7SV74K8X Q CLR CONV CONV ENABLE CNV LTC2320-14 SCK CLKOUT GND CMOS/LVDS GND SDR/DDR CONTROL LOGIC (FPGA, CPLD, DSP, ETC.) SDO1 - 8 10 10 NC7SVU04P5X (x 9) 232014 TA02 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS 16-/12-Bit, Octal 1.5Msps/CH, Simultaneous Sampling ADCs 3.3V/5V Supply, 20mW/Ch, 20ppmC Max Internal Reference, Flexible Inputs, 7mm x 8mm QFN Package ADCs LTC2320-16/LTC2320-12 LTC2310-16/LTC2310-14/ 16-/14-/12-Bit, Differential Input ADC with Wide LTC2310-12 Input Common Mode 3.3V/5V Supply, Single-Channel, 35mW, 20ppm/C Max Internal Reference, Flexible Inputs, 16-Lead MSO Package LTC2321-16/LTC2321-14/ Dual 16-/14-/12-Bit, 2Msps, Simultaneous LTC2321-12 Sampling ADCs 3.3V/5V Supply, 33mW/Ch, 20ppmC Max Internal Reference, Flexible Inputs, 4mm x 5mm QFN-28 Package LTC2324-16/LTC2324-14/ Quad 16-/14-/12-Bit, 2Msps/Channel, Simultaneous 3.3V/5V Supply, Single-Channel, 40mW, 20ppm/C Max Internal Reference, Flexible Inputs, 52-Lead QFN Package LTC2324-12 Sampling ADCs LTC2380-16/LTC2378-16/ 16-Bit, 2Msps/1Msps/500ksps/250ksps Serial, LTC2377-16/LTC2376-16 Low Power ADC 2.5V Supply, Differential Input, 96.2dB SNR, 5V Input Range, DGC, Pin-Compatible Family in MSOP-16 and 4mm x 3mm DFN-16 Packages DACs LTC2632 Dual 12-/10-/8-Bit, SPI VOUT DACs with Internal Reference 2.7V to 5.5V Supply Range, 10ppm/C Reference, External REF Mode, Rail-to-Rail Output, 8-Pin ThinSOTTM Package LTC2602/LTC2612/ LTC2622 Dual 16-/14-/12-Bit SPI VOUT DACs with External Reference 300A per DAC, 2.5V to 5.5V Supply Range, Rail-to-Rail Output, 8-Lead MSOP Package LTC6655 Precision Low Drift, Low Noise Buffered Reference 5V/4.096V/3.3V/3V/2.5V/2.048V/1.25V, 2ppm/C, 0.25ppm Peak-to-Peak Noise, MSOP-8 Package LTC6652 Precision Low Drift, Low Noise Buffered Reference 5V/4.096V/3.3V/3V/2.5V/2.048V/1.25V, 5ppm/C, 2.1ppm Peak-to-Peak Noise, MSOP-8 Package LT1818/LT1819 400MHz, 2500V/s, 9mA Single/Dual Operational Amplifiers -85dBc Distortion at 5MHz, 6nV/Hz Input Noise Voltage, 9mA Supply Current, Unity-Gain Stable LT1806 325MHz, Single, Rail-to-Rail Input and Output, Low -80dBc Distortion at 5MHz, 3.5nV/Hz Input Noise Voltage, Distortion, Low Noise Precision Op Amps 9mA Supply Current, Unity-Gain Stable LT6200 165MHz, Rail-to-Rail Input and Output, 0.95nV/Hz Low Noise, Low Distortion, Unity-Gain Stable Low Noise, Op Amp Family References Amplifiers 32 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC2320-14 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC2320-14 232014f LT 0117 * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2017