CAT.8100S
2.5 4 6.3 10
0E 0G 0J 1A
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F91
Type numbering system (Example : 10V 100µF)
Drawing
L
H
SS
W2
W1
(
mm
)
Case Code
C
N
LW1W2HS
6.0 ± 0.2
7.3 ± 0.2 3.2 ± 0.2
4.3 ± 0.2 2.2 ± 0.1
2.4 ± 0.1 2.5 ± 0.2
2.8 ± 0.2 1.3 ± 0.2
1.3 ± 0.2
Rated Capacitance (µF) Rated voltage (V)Rated voltage (V)
C Case N Case
68
10V
220
10V
Taping code
(Refer to page 213 for details)
F
19
21
31
4A
51
60
77
8M
9C
10 11
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
Marking
Standard ratings
LOW ESR
Resin-molded Chip,
C •N Case
∗As for the surge and derated voltage at 125
˚C
, refer to page 212 for details.
Specifications
Performance Characteristics
Item
Category
Temperature Range --55 ~ +125
˚C
(Rated temperature : 85
˚C
)
Capacitance Tolerance
Dissipation Factor (120Hz)
E.S.R. (100kHz)
±20%, ±10% (at 120Hz)
Refer to the list below.
Refer to the list below.
Leakage Current
•After 1 minute's application of rated voltage, leakage current
at 20
˚C
is not more than 0.01CV or 0.5mA, whichever is greater.
•After 1 minute's application of rated voltage, leakage current
at 85
˚C
is not more than 0.1CV or 5mA, whichever is greater.
•After 1 minute's application of derated voltage, leakage current
at 125
˚C
is not more than 0.125CV or 6.3mA, whichever is greater.
Capacitance Change
by Temperature
+15% Max. .(at +125
˚C
)
+10% Max. (at +85
˚C
)
--10% Max. (at --55
˚C
)
Damp Heat
(No voltage applied)
At 40˚C 90 ~ 95% R.H. 500 hours
Capacitance Change Within ±10% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Temperature Cycles
--55˚C / +125˚C 30 minutes each 5 cycles
Capacitance Change Within ±5% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Resistance
to Soldering Heat Capacitance Change Within ±3% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Test condition:
10 seconds reflow at 260
˚C
Surge∗
After application of surge in series with a 33
Ω
resistor at the rate of 30
seconds ON, seconds OFF, for 1000 sucessive test cycles at 85
˚C
,
capacitors meet the characteristic requirements listed below.
Capacitance Change....Within ±5% of initial value
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
Endurance∗
After 2000 hours' application of rated voltage in series with a 3
Ω
resistor
at 85
˚C
, or derated voltage in series with a 3
Ω
resistor at 125
˚C
,
capacitors meet the characteristics requirements listed below.
Capacitance Change......Within ±10%of initial value
Dissipation Factor..........Initial specified value or less
Leakage Current............Initial specified value or less
Shear Test
After applying the pressure load of 5N for 10
±
1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on an aluminum substrate,
neither exfoliation not its sign shall be
found at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the capacitor, the pressure load is
applied with a specified jig at the
center of the substrate so that the
substrate may bend by 1mm as
illustrated.
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
5N (0.51kg • f)
For 10±1seconds
20
R230
45 45
1
mm
068
100
150
220
330
470
680
686
107
157
227
337
477
687
C
N
C
C
N
N
N
C
C
C • N
N
N
C
C
N
N
N
Code
Cap.
(
µ
F)
V
250
100
250
250
100
100
100
250
250
250
100
100
100
300
250
100
100
100
12
12
12
12
10
16
18
10
12
14
10
14
16
8
10
10
12
18
220
470
150
220
330
470
680
100
150
220
220
330
470
68
100
150
220
330
Part Number
5.5
11.8
6.0
8.8
13.2
18.8
27.2
6.3
9.5
13.9
13.9
20.8
29.6
6.8
10.0
15.0
22.0
33.0
Leakage
Current
(µA) E.S.R.
(m
Ω
@100kHz)
Disspation
Factor
(%@120Hz)
Case
size
2.5V
4V
6.3V
10V
Rated Volt
(V)
Rated
Capacitance
(µF)
F910E227MCC
F910E477MNC
F910G157MCC
F910G227MCC
F910G337MNC
F910G477MNC
F910G687MNC
F910J107MCC
F910J157MCC
F910J227MCC
F910J227MNC
F910J337MNC
F910J477MNC
F911A686MCC
F911A107MCC
F911A157MNC
F911A227MNC
F911A337MNC
C
N
C
C
N
N
N
C
C
C
N
N
N
C
C
N
N
N
Dimensions
In case of capacitance tolerance
±
10% type, K will be put at 9th digit of type
numbering system.
