> > BY AMP INCORPORATED, ALL INTERNATIONAL RIGHTS RESERVED, AMP INCORPORATED PRODUCTS COVERED BY U.S. AND FOREIGN PATENTS AND/OR PATENTS PENDING, PRODUCT SPECIFICATION 1, SCOPE 1.1. Content This specification covers the performance requirements for the AMP Twin This connector is a multi-contact, edge board Connectors are available Leaf mother board connector. type assembly for wrap or solder applications. having .100, .125, .150 or .156 inch centerline spacing between adjacent contacts and .2Q inch spacing between contact rows. 1.2. Qualification When testing or inspecting the subject product. this document shall always be supported by the applicable product drawing and by 109-9000. Packaging Camponents Division Connector Test Methods. Incase of conflict the order of document precedence is as follows: A. Product Drawing B. This Product Specification Cc. 109-9000; Packaging Components Division Connector Test Methods 2. APPLICABLE DOCUMENTS 2.1. Applicable portions of the following documents form a part of the manufacturing control of this product. A. MIL-G-45204: Gold Plating. Electrodeposited. 2.2. The following documents describe testing of this product: A. 109-9000; Packaging Components Division Connector Test Methods. B. MIL-STD-1344: Test Methods for Electrical Connectors. 3, PERFORMANCE REQUIREMENTS 3.1. Ratings A. Current: 3,0 amperes maximum per contact B. Temperature: -55 to 105C ~~ t~ a a Eg ea a ge * Trademark of AMP Incorporated. at T qe a 95 te hae btavet de aff AMP INCORPORATED CHK ff AMP | Harrisburg, Pa. KI bk tea, UDF APPL? so 2-9: - |LOoC NO REV oT. Bubs Bp |A| 108-9027 | NAME DIST __ SHEET D [Rev. and retype i |e 10F & CONNECTOR, TWIN LEAF 14 LTR REVISION RECORD APP DATE AMP 1250 REV 7-78 >bd 3.2, Test Requirements and Procedures Summary Test Description Requirements Procedure Examination of Product Meets requirements of drawing Dimensional and visual Termination Resistance, Low Level .010 ohms maximum 50 mv maximum open circuit, 100 ma maximum short circuit. Termination Resistance Rated Current . 010 ohms maximum 3 amperes Insulation Resistance 5000 megohms minimum initial; 1000 megohms minimum final 500 vdc, unmated, Dielectric Withstanding Voltage Test Voltage vrms Centerline Spacing Altitude .100/.125 . i30/. 155 Sa Level 1000 1500 50, 000 ft. 400 600 70, 000 ft. 2350 400 5 ma maximum leakage Unmated connectors, test between adiacent contacts, and contacts to mounting hardware. Contact Separation Force 1.0 ounce minimum per contact pair Size 3 times with max.- ._ imum thickness gage O70; check with min- imum thickness gage .Oo4, Connector Mating Force 16,0 ounces maximum average per contact pair Maximum thickness gage .0O70. Durability No evidence of physical damage; meet contact separation force and termination resistance rated current, L0G cycles mating and unmating with maximum thickness gage . O70. Temperature Cycling No physical damage. -55 to 105C Vibration No intzrruption of cont- inuity greater than l microsecond; no physical damage Series wired and mated with printed circuit board. 10 to 55 Hz; .06 inch double amplitude, 100 ma current. Figure 1 jcont) AMP INCORPORATED ARAP | Harrisburg, Pa. p |A| 108-9027 |", SHEET 2 OF_ NAME CONNECTOR, TWIN LEAF AMP 2763-2 REV 7-78> Test Description Requirements Procedure Shock (Specified Pulse) No interruption of Series wired and mated continuity greater than with printed circuit l microsecond; no board. 1900 Gis, 6 physical damage. milliseconds, sawtooth, . 100 ma current. Humidity Remove from the chamber 90-95% RH, 96 hours and air dry at raom 40 C3; unmated. ambient conditions for 4 hours before electrical tests. Meet insulation resistance final and dielectric withstanding voltage, Figure 1 (end) AMP INCORPORATED SHEET | AMP | Harrisburg, Pa. 30 F 6 ftoc NO REV B|A!| 108-9027 |p NAME CONNECTOR, TWIN LEAF AMP 1251-13 REV 7-78 ip3.3. Connector Tests and Sequence MIL-STD-1344 109-9000 Test Sequence Test Requirement Method 1 2. Paragraph Examination of Product 5.1, x S Connector Mating Force 2013.1 2. 8. x Termination Resistance , 3002.1 3.24 Low Level [{b) * * Termination Resistance, 4A. 2 oe Rated Current (b) 3004.1 963 * x Insulation Resistance 3003.1 5.4, x Dielectric Withstanding Volta 3001.1 5.5 x electri e oe 3 8 8 cond I, Il] & IV Contact Separation Force 2014 5.7. x Durability 2016 5,10, x x Contact Separation Force Termination Resistance, Rated Current Temperature Cycling {a) LOO3.1, cand A 5.11. x Vibration 2005.1, cond I 5,2. x Shock (Specified Pulse) 2004.1, cond G 5.13, x 1002. 2 Hi idit 5.14, ony Type I, cond B + x Insulation Resistance Dielectric Withstanding Voltage Termination Resistance, - 3002, 1 5.2, x Low Level (b) * Termination Resistance , 3004, 1 5.3, x Rated Current (b} x (a) Upper temperature Hmit 105C (>) See Figure 3 Figure 2 AMP INCORPORATED AMP | Harrisburg, Pa. SHEET 4A OFS p |A/ 108-9027 |", NAME CONNECTOR, TWIN LEAF AMP 2783-2 REV 7-78 Ysbal 3.4. Selection of Test Samples A. Test samples shall consist of 6 connectors containing the largest number of positions of each connector type offered 3 each Test Sequence i and Test Sequence 2. Two additional specimens shall be selected fram the least number of positions offered and tested to Test Sequence 2. B. Connectors shall be mounted in accordance with AMP Instruction Sheet 7498. Card guides, screws, keys and other hardware normally used with the connectors shall be included with the test specimens. Termination Resistance Measurement Points Printed Circuit Board (See Figure ) Printed Circuit Board Power Supply Figure 3 Typical Termination Resistance Measurement Points for Board to Board Type Connectors 4} SHEET | AMP 2 OF LOG Harrisburg, Pa. AMP INCORPORATED pn |A| 108-9027 REV D NAME CONNECTOR, TWIN LEAF AMP 1251-13 REV 7-78 <aA BSC Typ 005 < B ogo LYP |} .003 Total (See Note 3) s (062 ~~ pe a ft ee $$ (+ , 005 paQ$ > -A- a 4 Section D-D _. eg . 062 (See Note 6) Connector A Contact B . Bsc Spacing .1900 .1007 .052 125 ~l25] .078 -150 ~150] .094 ~156 .156[ .094 Notes: 1. Dimensions are in inches, 2. Unless otherwise specified, tolerance is +. 005, 3. The test card shail extend 4,004.02 from the receptacle after insertion. 4, Number of contacts shall be the same as on the corresponding printed wiring connector, 5, Printed circuit test board shall be 2 oz copper and gold over nickel plated per MIL-STD-275. 6, This dimension shall be the minimum connector card slot length minus .008. =| Al. 004 Total 7, Conductor configuration optional beyond card slot depth. AMP | AMP INCORPORATED Harrisburg, Pa. SHEET & OFS B|A! 108-9027 |"; REV NAME CONNECTOR, TWIN LEAF 8. Printed wiring shall be identical on both sides, Figure + Printed Circuit Board AMP 2783-2 REV 7-78