50-165 Watts NTQ160 Series Total Power: 50-165 Watts Input Voltage: 85-264 VAC # of Outputs: Quad Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current Special Features Environmental Operating temperature: 0 to 50C ambient; derate each output at 2.5% per degree from 50 to 70C Adjustment range Hold-up time Overload protection Overvoltage protection Standby output Power failure TTL logic signal goes high 100-500 msec after V1 output; it goes low at least 4 msec before loss of regulation Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop minimum, will operate without remote sense connected. Reverse connection protection. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation. Remote Inhibit Remote sense DC O Safety Humidity: Operating; non-condensing 10% to 95% Storage temperature: -40 to 85C Temperature coefficient: .04% per C MTBF demonstrated: >1 million hours at full load and 25C ambient conditions 50W convection, 165 W with 30 CFM forced air 1.8V - 3.5V; 3.0V - 5.5V on outputs one and two 20 ms @ 165 W load Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating. Latching type recycle AC to reset. Tracks outputs 1 & 2: 20% to 35% above output setting 5V@ 2 A regulated 5% Logic Control Electromagnetic susceptibility: Designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.7 G peak 5 Hz to 500 Hz, operational <1 mA @ 50/60 Hz, 264 VAC input Output Maximum power * Active power factor correction * EN61000-3-2 compliance * Remote sense on outputs one and two * Power fail and remote inhibit * 5V Standby output * DC Power good * Single wire current sharing on outputs one and two * Wide range adjustable on outputs 1 & 2 * Built-in Class B EMI filter * Overvoltage protection * Overload protection * Thermal overload protection * Outputs 3 & 4 are floating 85-264 VAC 47-63 Hz 38 A max., cold start @ 25C 65% typical at full load @ 115 VAC input FCC Class B conducted and radiated, CISPR 22 Class B conducted and radiated, EN55022 Class B conducted and radiated, VDE 0878 PT3 Class B conducted and radiated. 0.99 typical VDE 0805/EN60950 (IEC950) UL CSA NEMKO UL1950 CSA 22.2-234 Level 3 EN 60950/EMKO-TUE (74-sec) 203 EN60950/EN41003 Certificate and report Mark (LVD) BABT CB CE 21310-3336-0021 (129066) E186249 LR109492C P00100493 650251, NC/00069 9661, 9662, 8788 rev 04.29.04 116 Americas: (760) 930-4600 Support: (888) 41-ASTEC or (407) 241-2752 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 NTQ160 Series Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30 CFM Forced Air Peak Load1 Regulation2 Ripple P/P (PARD)3 NTQ162 +3.3 V(1.8 - 3.5V) +5 V (3 - 5.5V) 12 V* 12 V* 2A 0A 0A 0A 15 A 10 A 2A 2A 30 A 20 A 4.5 A 4.5 A 38 A 22 A 5A 5A 2% 2% 3% 3% 50 mV 50 mV 120 mV 120 mV NTQ163 +5 V (3 - 5.5V) +3.3 V (1.8 - 3.5V) 12 V* 12 V* 2A 0A 0A 0A 15 A 10 A 2A 2A 30 A 20 A 4.5 A 4.5 A 32 A 22 A 5A 5A 2% 2% 3% 3% 50 mV 50 mV 120 mV 120 mV NTQ165 +3.3 V (3 - 5.5V) 2A 15 A 30 A 32 A 2% +2.5 V (1.8 - 3.5V) 0 A 10 A 20 A 22 A 2% 5 V* 0A 2A 4A 5A 3% 12 V* 0A 2A 4A 5A 3% * outputs are floating 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. Minimum loads are required. In parallel minimum loads are 2.5 A on the V1 output and 1 A on the V2 output for each power supply. 5. Total output current between V1 and V2 is 40A maximum. 50 mV 50 mV 120 mV 120 mV SK5 6 7 8 9 10 0.95 [24.0] Ordering Information 0.55 [14.0] C42 C86 C84 C48 C47 C41 R32 C68 R87 SEC_DB Z4 R73 HTSK-SEC3 R24 R25 R26 + + D24 R7 9 L13 R67 L10 + + D22 SCR1 TP1 + C23 C 1999 ASTEC Q5 CUSTOM POWER (PHIL.) 9 C24 T3 4 1 T1-W1 Q4 C21 7 VR3 C26 SO1 R34 1 + B+ 7.40 [188.0] R39 D10 R47 C18 + C63 C19 + 6 8.50 [216.0] IC2 + 10 C60 12 6.61 [168.0] 5 THR5 T2 D12 IC6 Z1 B- T1-W1A D17 R63 HTSK-SEC2 R42 P401 3 D1 C22 C31 R65 IC9 1 D13 + R48 042-66102310D Q8 L5 + + Q7 L8 R80 R68 D19 L6 R84 D21 D20 D18 R35 C94 HTSK-SEC1 C72 R30 R89 R66 D27 C40 C37 R27 IC7 L9 C36 R77 D23 + C20 D11 HTSK-PRI2 R31 B+ R6 D16 C70 C11 C10 + PRI_DB C5 R64 Q2 Z2 Q3 b + IC8 C33 VR2 VR1 C29 C27 + + C28 R95 L12 HTSK-PRI1 R5 C9 D1 L3 DB1 C4 B- Q1 b (SK6) 12V Molex:09-50-8041 (USA) Molex: 09-91-0400 (UK) PINS: 08-58-0111 (SK5) Control Signals: Molex: 90142-0010 PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Astec Connector Kit #70-841-014, includes all of the above L2 THR1 SK1 C3 F4A 250V F1 C71 C2 4 C3 Molex: 09-50-8051 (USA) Molex: 09-91-0500 (UK) PINS: 08-58-0111 Molex BB-124-08 HTSK-RECT L4 L1 VDR1 C1 SK2,3,4: V2 SWP 5V Standby +V2 Sense V1 SWP COMMON +V1 Sense Sense COMMON Remote Inhibit DC Power Good Power Fail C66 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 Mating Connectors (SK1) AC Input: SK5 R94 R58 R57 R56 R55 SK2 SK3 SK4 SK6 a 1 L15 + 2 + + THR3 THR2 C38 PIN 1 PIN 2 PIN 3 PIN 4 V1 Common V2 V4 Common V4 V3 Common V3 THR4 C67 Ground Neutral Live L7 PIN 1 PIN 3 PIN 5 + C46 C43 C77 SK1 3 10 1 R41 SK3 D9 SK4 C89 C91 4 R46 C85 R78 L11 SK2 SK6 SK6 Connector SK4 SK5 SK3 1 2 3 4 5 SK2 5 3 a 1 SK1 4.25 [108.0] 0.75 [19.0] 1.50 [38.1] Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance .02". 3. Remote inhibit requires an external contact closure to activate 4. Mounting maximum insertion depth is 0.12". 5. Warranty: 1 year 6. Weight: 2.38 lb. /1.08 kg www.astecpower.com 117 R27 SK2 L6 HTSK-SEC1 SK3 C27 C33 L12 C68 C71 + SCR1 D23 SK4 C5 DB1 C4 THR1 R41 R65 VDR1 T1-W1A D17 R63 R48 R77 + + + THR4 R46 R66 + D18 4.25 [108.0] + C40 R89 + + + R31 4 5 R35 Z1 2 C20 D11 SK1 3 C19 R39 1 C18 D13 R30 C48 + 3 SK6 NTQ160 Series 4 C3 C46 C43 SK2 R73 C89 R80 C91 Q2 D19 12 1 Q8 Z4 SK3 SO1 Q7 C21 VR3 C26 T2 R24 R25 R26 7 6 SK4 TP1 T1-W1 D9 10 C29 C42 R64 SEC_DB 1 C41 C 1999 ASTEC Q5 CUSTOM POWER (PHIL.) B- C24 Q4 C3 C86 C84 SK5 C70 Q3 L4 L5 10 1 T3 C47 9 1 R87 1 + C85 R78 R6 Q1 HTSK-RECT D20 D1 R5 D16 HTSK-PRI1 L1 R34 IC9 F4A 250V C63 L2 PRI_DB F1 + B+ HTSK-SEC3 C23 5 D10 C11 VR2 VR1 HTSK-SEC2 042-66102310D C37 B+ B- C9 IC6 R47 C31 C60 L13 D12 IC2 C2 C22 C10 + + Z2 D21 + D22 4 D27 SK1 + P401 R7 9 THR5 + C66 R84 3 D1 R94 R58 R57 R56 R55 + R95 + C67 + L7 C36 R42 C28 L8 C38 L9 D24 C94 THR2 C72 R67 R68 THR3 IC7 L10 C77 R32 SK5 1 2 3 4 5 L11 6 7 8 9 10 IC8 HTSK-PRI2 L15 L3 SK6 C1 + a b b a 1.50 [38.1] 0.75 [19.0] 6.61 [168.0] 8.50 [216.0] 0.55 [14.0] 7.40 [188.0] 0.95 [24.0] 0.88 [22.3] 1.07 [27.3] a a b b 2.50 [63.5] 2.11 [53.5] b b a a M3 (8 PLACES) #6-32 (8 PLACES)