2K x 8 Dual-Port Static RAM
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Cypress Semiconductor Corporation • 198 Champion Court • San Jose,CA 95134-1709 • 408-943-2600
Document #: 38-06031 Rev. *E Revised March 24, 2009
Features
■True dual-ported memory cells that enable simultaneous reads
of the same memory location
■2K x 8 organization
■0.65 micron CMOS for optimum speed and power
■High speed access: 15 ns
■Low operating power: ICC = 110 mA (maximum)
■Fully asynchronous op eration
■Automatic power down
■Master CY7C132/CY7C136/CY7C136A[1] easily expands data
bus width to 16 or more bits using slave CY7C142/CY7C146
■BUSY output flag on CY7C132/CY7C136/CY7C136A;
BUSY input on CY7C142/CY7C146
■INT flag for port to port communication (52-Pin PLCC/PQFP
versions)
■CY7C136, CY7C136A, and CY7C146 availabl e in 52-pin
PLCC and 52-pin PQFP packages
■Pb-free packages available
Functional Description
The CY7C132, CY7C136, CY7C136A, CY7C142, and CY7C146
are high speed CMOS 2K x 8 dual-port static RAMs. Two ports
are provided to permit independent access to any location in
memory . The CY7C132, CY7C136, and CY7C136A can be used
as either a standalone 8-bit dual-port static RAM or as a
MASTER dual-port RAM, in conjunction with the
CY7C142/CY7C146 SLAVE dual-port device. They are used in
systems that require 16-bit or greater word widths. This is the
solution to applications that require shared or buffered data, such
as cache memory for DSP, bit-slice, or multiprocessor designs.
Each port has independent control pins; chip enable (CE), write
enable (R/W), and output enable (OE). BUSY flags are provided
on each port. In addition, an interrupt flag (INT) is provided on
each port of the 52-pin PLCC version. BUSY signals that the port
is trying to access the same location currently being accessed
by the other port. On the PLCC version, INT is an interrupt fl ag
indicating that data is placed in an un ique location (7FF for the
left port and 7FE for the right port).
An automatic power down feature is controlled independently on
each port by the chip enable (CE) pins.
R/WL
BUSYL
CEL
OEL
A10L
A0L A0R
A10R
R/WR
CER
OER
CER
OER
CEL
OEL
R/WLR/WR
I/O7L
I/O0L
I/O7R
I/O0R
BUSYR
INTLINTR
ARBITRATION
LOGIC
(7C132/7C136 ONLY)
AND
INTERRUPTLOGIC
(7C136/7C146ONLY)
CONTROL
I/O CONTROL
I/O
MEMORY
ARRAY ADDRESS
DECODER
ADDRESS
DECODER
[2]
[3] [3]
[2]
Logic Block Diagram
Notes
1. CY7C136 and CY7C136A are functionally identical.
2. CY7C132/CY7C136/CY7C136A (Master): BUSY is open drain output and requires pull up resistor. CY7C142/CY7C146 (Slave): BUSY is input.
3. Open drain outputs; pull up resistor required.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 2 of 15
Pinouts
Figure 1. 52-Pin PLCC (Top View) Figure 2. 52-Pin PQFP (Top View)
Selection Guide
Specification 7C136-15[4]
7C146-15
7C132-25 [4]
7C136-25
7C142-25
7C146-25
7C132-30
7C136-30
7C142-30
7C146-30
7C132-35
7C136-35
7C142-35
7C146-35
7C132-45
7C136-45
7C142-45
7C146-45
7C132-55
7C136-55
7C136A-55
7C142-55
7C146-55
Unit
Maximum Access Time 15 25 30 35 45 55 ns
Maximum Operating Current Com’l/Ind 190 170 170 120 120 110 mA
Maximum Standby Current Com’l/Ind 75 65 65 45 45 35 mA
Shaded areas contain preliminary information.
1
VCC
OER
A0R
8
9
10
11
12
13
14
15
16
17
18
19
20
46
45
44
43
42
41
40
39
38
37
36
35
34
2122 23 24 25 26 27 28 29 30 31 32 33
7 6 5 4 3 2 52 51 50 49 48 47
A1R
A2R
A3R
A4R
A5R
A6R
A7R
A8R
A9R
NC
I/O7R
A1L
A2L
A3L
A4L
A5L
A6L
A7L
A8L
A9L
I/O0L
I/O1L
I/O2L
I/O3L
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
4L
5L
6L
7L
0R
1R
2R
3R
4R
5R
6R
NC
GND
OE
BUSY
INT
A
R/W
CE
R/W
BUSY
INT
0L
L
L
L
L
L
CER
R
R
R
7C136/7C136A
7C146
A
10L
A10R
46
1
2
3
4
5
6
7
8
9
10
11
12
13
39
38
37
36
35
34
33
32
31
30
29
28
27
1415 16 17 18 19 20 21 22 23 24 25 26
52 51 50 49 48 47 45 44 43 42 41 40
VCC
OE
BUSY
INT
A
R/W
CE
R/W
BUSY
INT
0L
L
L
L
L
L
CER
R
R
R
OER
A0R
A1R
A2R
A3R
A4R
A5R
A6R
A7R
A8R
A9R
NC
I/O7R
A1L
A2L
A3L
A4L
A5L
A6L
A7L
A8L
A9L
I/O0L
I/O1L
I/O2L
I/O3L
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
4L
5L
6L
7L
0R
1R
2R
3R
4R
5R
6R
NC
GND
7C136/7C136A
7C146
A
10L
A10R
Note:
4. 15 ns and 25 ns version available in PQFP and PLCC packages only.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 3 of 15
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ..................................... −65°C to +150°C
Ambient Temperature with
Power Applied.................................................. −55°C to +125°C
Supply Voltage to Ground Potential
(Pin 48 to Pin 24) .................................................−0.5V to +7.0V
DC Voltage Applied to Outputs
in High Z State.....................................................−0.5V to +7.0V
DC Input Voltage................................................. −3.5V to +7.0V
Output Current into Outputs (LOW).......... ... .............. ..20 mA
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch up Current.................................................... > 200 mA
Operating Range
Range Ambient Temperature VCC
Commercial 0°C to +70°C 5V ± 10%
Industrial –40°C to +85°C 5V ± 10%
Notes
5. BUSY and INT pins only.
6. Duration of the short circuit should not exceed 30 seconds.
7. At f = fMAX, address and data inputs ar e cycling at the maximum frequency of read cycle of 1/trc and using AC Test Waveforms inp ut levels of GND to 3V.
Electrical Characteristics
Over the Operating Range
Parameter Description Test Conditions 7C136-15[4]
7C146-15
7C132-30[4]
7C136-25, 30
7C142-30
7C146-25, 30
7C132-35,45
7C136-35,45
7C142-35,45
7C146-35,45
7C132-55
7C136-55
7C136A-55
7C142-55
7C146-55 Unit
Min Max Min Max Min Max Min Max
VOH Output HIGH
voltage VCC = Min., IOH = –4.0 mA 2.4 2.4 2.4 2.4 V
VOL Output LOW
voltage IOL = 4.0 mA 0.4 0.4 0.4 0.4 V
IOL = 16.0 mA[5] 0.5 0.5 0.5 0.5
VIH Input HIGH
voltage 2.2 2.2 2.2 2.2 V
VIL Input LOW
voltage 0.8 0.8 0.8 0.8 V
IIX Input load current GND < VI < VCC –5 +5 −5+5−5+5−5+5μA
IOZ Output leakage
current GND < VO < VCC, Output Disabled –5 +5 −5+5−5+5−5+5μA
IOS Output short
circuit current[6] VCC = Max., VOUT = GND –350 −350 −350 −350 mA
ICC VCC Operating
Supply Current CE = VIL, Outputs Open,
f = fMAX[7] Com’l/
Ind’l 190 170 120 110 mA
ISB1 Standby current
both ports, TTL
Inputs
CEL and CER > VIH,
f = fMAX[7] Com’l/
Ind’l 75 65 45 35 mA
ISB2 Standby Current
One Port,
TTL Inputs
CEL or CER > VIH,
Active Port Outputs Open,
f = fMAX[7]
Com’l/
Ind’l 135 115 90 75 mA
ISB3 Standby Current
Both Ports,
CMOS Inputs
Both Ports CEL and
CER > VCC – 0.2V , VIN > VCC – 0.2V
or VIN < 0.2V, f = 0
Com’l/
Ind’l 15 15 15 15 mA
ISB4 Standby Current
One Port,
CMOS Inputs
One Port CEL or CER > VCC – 0.2V ,
VIN > VCC – 0.2V or VIN < 0.2V,
Active Port Outputs Open, f = fMAX[7]
Com’l/
Ind’l 125 105 85 70 mA
Shaded areas contain preliminary information.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 4 of 15
Capacitance
This parameter is guaranteed but not tested.
Parameter Description Test Conditions Max Unit
CIN Input Capacit ance TA = 25°C, f = 1 MHz, VCC = 5.0V 15 pF
COUT Output Capacitance 10 pF
Figure 3. AC Test Loads and Waveforms
3.0V
5V
OUTPUT
R1 893Ω
R2
347Ω
30 pF
INCLUDING
JIG AND
SCOPE
GND 90% 90%
10%
<5ns <5ns
5V
OUTPUT
R1 893Ω
R2
347Ω
5pF
INCLUDING
JIG AND
SCOPE
(a) (b)
OUTPUT 1.4V
Equivalent to: TH ÉVENIN EQUIVALENT
5V
281Ω
30 pF
BUSY
OR
INT
BUSY Output Load
(CY7C132/CY7C136 Only)
10%
ALL INPUT PULSES
250Ω
Switching Characteristics
Over the Operating Range (Speeds -15, -25, -30) [8]
Parameter Description 7C136-15 [4]
7C146-15
7C132-25 [4]
7C136-25
7C142-25
7C146-25
7C132-30
7C136-30
7C142-30
7C146-30 Unit
Min Max Min Max Min Max
Read Cycle
tRC Read Cycle Time 15 25 30 ns
tAA Address to Data Valid [9] 15 25 30 ns
tOHA Data Hold from Address Change 000ns
tACE CE LOW to Data Valid [9] 15 25 30 ns
tDOE OE LOW to Data Valid [9] 10 15 20 ns
tLZOE OE LOW to Low Z [7, 10] 333ns
tHZOE OE HIGH to High Z [7, 10, 11] 10 15 15 ns
tLZCE CE LOW to Low Z [7, 10] 355ns
tHZCE CE HIGH to High Z [7, 10, 11] 10 15 15 ns
tPU CE LOW to Power Up [7] 000ns
tPD CE HIGH to Power Down [7] 15 25 25 ns
Shaded areas contain preliminary information.
Notes
8. Test conditions assume signal t ransition times o f 5 ns or less, timing refer ence levels of 1.5V, input pul se le vels of 0 t o 3.0 V and output lo ading o f the spe cified I OL/IOH,
and 30 pF load capacit ance.
9. AC test conditions use VOH = 1.6V and VOL = 1.4V.
10.At any given temperature and voltage condition for any given device, tHZCE is less than tLZCE and tHZOE is less than tLZOE.
11. tLZCE, tLZWE, tHZOE, tLZOE, tHZCE, and tHZWE are tested with CL = 5pF as in (b) of AC Test Loads and Waveforms. Tr ansition is measured ± 500 mV from steady state
voltage.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 5 of 15
Write Cycle[12]
tWC Write Cycle Time 15 25 30 ns
tSCE CE LOW to Write End 12 20 25 ns
tAW Address Setup to Write End 12 20 25 ns
tHA Address Hold from Write End 222ns
tSA Address Setup to Write Start 000ns
tPWE R/W Pulse Width 12 15 25 ns
tSD Data Setup to Write End 10 15 15 ns
tHD Data Hold from Wr ite End 000ns
tHZWE R/W LOW to High Z [7] 10 15 15 ns
tLZWE R/W HIGH to Low Z [7] 000ns
Busy/Interrupt Timing
tBLA BUSY LOW from Address Match 15 20 20 ns
tBHA BUSY HIGH from Address Mismatch[13] 15 20 20 ns
tBLC BUSY LOW from CE LOW 15 20 20 ns
tBHC BUSY HIGH from CE HIGH[13] 15 20 20 ns
tPS Port Set Up for Priority 555ns
tWB R/W LOW after BUSY LOW[14] 000ns
tWH R/W HIGH after BUSY HIGH 13 20 30 ns
tBDD BUSY HIGH to Valid Data 15 25 30 ns
tDDD Write Data Valid to Read Data Valid Note 15 Note 15 Note 15 ns
tWDD Write Pulse to Data Delay Note 15 Note 15 Note 15 ns
Interrupt Timing [16]
tWINS R/W to INTERRUPT Set Time 15 25 25 ns
tEINS CE to INTERRUPT Set Time 15 25 25 ns
tINS Address to INTERRUPT Set Time 15 25 25 ns
tOINR OE to INTERRUPT Reset Time[13] 15 25 25 ns
tEINR CE to INTERRUPT Reset Time[13] 15 25 25 ns
tINR Address to INTERRUPT Reset Time[13] 15 25 25 ns
Shaded areas contain preliminary information.
Switching Characteristics
Over the Operating Range (Speeds -15, -25, -30) [8] (continued)
Parameter Description 7C136-15 [4]
7C146-15
7C132-25 [4]
7C136-25
7C142-25
7C146-25
7C132-30
7C136-30
7C142-30
7C146-30 Unit
Min Max Min Max Min Max
Notes
12.The internal write ti me of the memo ry is defined by the overlap o f CE LOW and R/W LOW. Both signals must be LOW to i nitiate a write and either signal can termina te
a write by going HIGH. The data input setup and hold timing must be referenced to the rising edge of the signal that terminate s the write.
13.These parameters are measured from the input signal changing, until the output pin goes to a high impedance state.
14.CY7C142/CY7C146 only.
15.A write operation on Port A, where Port A has priority, leaves the data on Port B’s outputs undisturbed unt il one access time after one of the following:
BUSY on Port B goes HIGH.
Port B’s address toggled.
CE for Port B is toggled.
R/W for Port B is toggled during valid read.
16.52-pin PLCC and PQFP versions only.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 6 of 15
Switching Characteristics
Over the Operating Range (Speeds -35, -45, -55) [8]
Parameter Description
7C132-35
7C136-35
7C142-35
7C146-35
7C132-45
7C136-45
7C142-45
7C146-45
7C132-55
7C136-55
7C136A-55
7C142-55
7C146-55 Unit
Min Max Min Max Min Max
Read Cycle
tRC Read Cycle Time 35 45 55 ns
tAA Address to Data Valid[9] 35 45 55 ns
tOHA Data Hold from Address Change 0 0 0 ns
tACE CE LOW to Data Valid[9] 35 45 55 ns
tDOE OE LOW to Data Va lid[9] 20 25 25 ns
tLZOE OE LOW to Low Z[7, 10] 333ns
tHZOE OE HIGH to High Z[7, 10, 11] 20 20 25 ns
tLZCE CE LOW to Low Z[7, 10] 555ns
tHZCE CE HIGH to High Z[7, 10, 11] 20 20 25 ns
tPU CE LOW to Power Up[7] 000ns
tPD CE HIGH to Power Down[7] 35 35 35 ns
Write Cycle[12]
tWC Write Cycle Time 35 45 55 ns
tSCE CE LOW to Write End 30 35 40 ns
tAW Address Setup to Write End 30 35 40 ns
tHA Address Hold from Write End 2 2 2 ns
tSA Address Setup to Write Start 0 0 0 ns
tPWE R/W Pulse Width 25 30 30 ns
tSD Data Setup to Write End 15 20 20 ns
tHD Data Hold from Wr ite End 0 0 0 ns
tHZWE R/W LOW to High Z [7] 20 20 25 ns
tLZWE R/W HIGH to Low Z [7] 000ns
Busy/Interrupt Timing
tBLA BUSY LOW from Address Match 20 25 30 ns
tBHA BUSY HIGH from Address Mismatch[13] 20 25 30 ns
tBLC BUSY LOW from CE LOW 20 25 30 ns
tBHC BUSY HIGH from CE HIGH[13] 20 25 30 ns
tPS Port Set Up for Priority 5 5 5 ns
tWB R/W LOW after BUSY LOW[14] 000ns
tWH R/W HIGH after BUSY HIGH 30 35 35 ns
tBDD BUSY HIGH to Valid Data 35 45 45 ns
tDDD Write Data Valid to Read Data Valid Note 15 Note 15 Note 15 ns
tWDD Write Pulse to Data Delay Note 15 Note 15 Note 15 ns
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 7 of 15
Interrupt Timing [16]
tWINS R/W to INTERRUPT Set Time 25 35 45 ns
tEINS CE to INTERRUPT Set Time 25 35 45 ns
tINS Address to INTERRUPT Set Time 25 35 45 ns
tOINR OE to INTERRUPT Reset Time[13] 25 35 45 ns
tEINR CE to INTERRUPT Reset Time[13] 25 35 45 ns
tINR Address to INTERRUPT Reset Time[13] 25 35 45 ns
Switching Characteristics
Over the Operating Range (Speeds -35, -45, -55) [8] (continued)
Parameter Description
7C132-35
7C136-35
7C142-35
7C146-35
7C132-45
7C136-45
7C142-45
7C146-45
7C132-55
7C136-55
7C136A-55
7C142-55
7C146-55 Unit
Min Max Min Max Min Max
Switching Waveforms
Figure 4. Read Cycle No. 1 (Either Port-Address Access) [17, 18]
Figure 5. Read Cycle No. 2 (Either Port-C E/OE )[17, 19]
tRC
tAA
tOHA
DATA VALIDPREVIOUS DATA VALID
DATA OUT
ADDRESS
tACE
tLZOE tDOE tHZOE
tHZCE
DATA VALID
DATA OUT
CE
OE
tLZCE
tPU
ICC
ISB
tPD
Notes
17.R/W is HIGH for read cycle.
18.Device is continuously selected, CE = VIL and OE = VIL.
19.Address valid prior to or coincident with CE transition LOW.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 8 of 15
Figure 6. Read Cycle No. 3 (Read with BUSY Master: CY7C132 and CY7C136/CY7C136A)
Figure 7. Write Cycle No.1 (OE Three-States Data I/Os—Either Port) [12, 20]
Switching Waveforms (continued)
tBHA
tBDD
VALID
tDDD
tWDD
ADDRESS MATCH
ADDRESS MATCH
R/WR
ADDRESSR
DINR
ADDRESSL
BUSYL
DOUTL
tPS
tBLA
tRC
tPWE
VALID
tAW
tWC
DATA VALID
HIGH IMPEDANCE
tSCE
tSA tPWE
tHD
tSD
tHA
tHZOE
CE
R/W
ADDRESS
OE
DOUT
DATAIN
Note
20.If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of tPWE or tHZWE + tSD to allow the data I/O pins to enter high impeda nce
and for data to be placed on the bus for the required tSD.
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 9 of 15
Figure 8. Write Cycle No. 2 (R/W Three-St ates Data I/Os—Either Port)[12, 21]
Figure 9. Busy Timing Diagram No. 1 (CE Arbitration)
Switching Waveforms (continued)
tAW
tWC
tSCE
tSA tPWE
tHD
tSD
tHZWE
tHA
HIGH IMPEDANCE
CE
R/W
ADDRESS
DOUT
DATAIN
tLZWE
DATAVALID
ADDRESS MATCH
tPS
CEL Valid First:
tBLC tBHC
ADDRESS MATCH
tPS
tBLC tBHC
BUSYL
CER
CEL
ADDRESSL,R
BUSYR
CEL
CER
ADDRESSL,R
CER Valid First:
Note
21.If the CE LOW transition occurs simultaneously with or after the R/W LOW transition , the outputs remain in a high impedance state .
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 10 of 15
Figure 10. Busy Timing Diagram No. 2 (Address Arbitration)
Figure 11. Busy Timing Diagram No. 3 (Write with BUSY, Slave: CY7C142/CY7C146)
Switching Waveforms (continued)
Left Address Valid First:
ADDRESS MATCH
tPS
ADDRESSL
BUSYR
ADDRESS MISMATCH
tRCor tWC
tBLA tBHA
ADDRESSR
ADDRESS MATCH ADDRESS MISMATCH
tPS
ADDRESSL
BUSYL
tRCor tWC
tBLA tBHA
ADDRESSR
Right Address Valid First:
tPWE
tWB tWH
BUSY
R/W
CE
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 11 of 15
Interrupt Timing Diagrams [16]
Figure 12. Left Side Sets INTR
Figure 13. Right Side Clears INTR
Figure 14. Right Side Sets INTL
Figure 15. Right Side Clears INTL
Switching Waveforms (continued)
WRITE 7FF
tINS
ADDRESSL
R/WL
tWC
tEINS
CELtHA
tSA tWINS
INTR
READ 7FF
tRC
tEINR
tHA tINR
tOINR
ADDRESSR
CER
R/WR
INTR
OER
WRITE 7FE
tINS
ADDRESSR
R/WR
tWC
tEINS
CERtHA
tSA tWINS
INTL
READ 7FE
t
EINR
t
HA
t
INR
t
OINR
ADDRESS
L
CE
L
R/
W
L
INT
L
OE
L
t
RC
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 12 of 15
Figure 16. Typical DC and AC Characteristics
1.4
1.0
0.4
4.0 4.5 5.0 5.5 6.0 –55 25 125
1.2
1.0
120
100
80
60
40
20
0 1.0 2.0 3.0 4.0
OUTPUT SOURCE CURRENT (mA)
SUPPLY VOLTAGE (V)
NORMALIZED SUPPLY CURRENT
vs. SUPPLY VOLTAGE NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (°C) OUTPUT VOLTAGE (V)
OUTPUT SOURCE CURRENT
vs. OUTPUT VOLTAGE
0.0
0.8 0.8
0.6
0.6
NORMALIZED I
CC
, I
SB
V
CC
= 5.0V
V
IN
= 5.0V T
A
= 25°C
0
I
CC
I
CC
1.6
1.4
1.2
1.0
0.8
–55 125
NORMALIZED t
AA
NORMALIZED ACCESS TIME
vs. AMBIENT TEMPERATURE
AMBIENT TEMPERATURE (°C)
1.4
1.3
1.2
1.0
0.9
4.0 4.5 5.0 5.5 6.0
NORMALIZED t
AA
SUPPLY VOLTAGE (V)
NORMALIZED ACCESS TIME
vs. SUPPLY VOLTAGE
120
140
100
60
40
20
0.0 1.0 2.0 3.0 4.0
OUTPUT SINK CURRENT (mA)
0
80
OUTPUT VOLTAGE (V)
OUTPUT SINK CURRENT
vs. OUTPUT VOLTAGE
0.6
0.8
1.25
1.0
0.75
10 40
NORMALIZED I
CC
0.50
NORMALIZED I
CC
vs. CYCLE TIME
CYCLE FREQUENCY (MHz)
3.0
2.5
2.0
1.5
0.5
0 1.0 2.0 3.0 5.0
NORMALIZED t
PC
25.0
30.0
20.0
10.0
5.0
0 200 400 600 800
DELTA t
AA
(ns)
0
15.0
0.0
SUPPLY VOLTAGE (V )
TYPICAL POWER-ON CURRENT
vs. SUPP LY VOLTAG E
CAPACITANCE (pF)
TYPICAL ACCESS TIME CHANGE
vs. OUTPUT LOADING
4.0 1000
1.0
20 30
0.2
0.6
1.2
I
SB3
0.2
0.4
I
SB3
25
1.1
V
IN
= 0.5V
NORMALIZED I
CC
, I
SB
V
CC
= 5.0V
T
A
= 25°C V
CC
= 5.0V
V
CC
= 5.0V
T
A
= 25°C
T
A
= 25°C
V
CC
= 4.5V
V
CC
= 5.0V
T
A
= 25°C
[+] Feedback
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
Document #: 38-06031 Rev. *E Page 13 of 15
Ordering Information
Speed
(ns) Ordering Code Package
Diagram Package Type Operating
Range
15 CY7C136-15JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-15NC 51-85042 52-Pin Plastic Quad Flatpack
25 CY7C136-25JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-25JXC 52-Pin Plastic Leaded Chip Carrier (Pb-Free)
CY7C136-25NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C136-25NXC 52-Pin Plastic Quad Flatpack (Pb-Free)
CY7C136-25JXI 51-85004 52-Pin Plastic Leaded Chip Carrier (Pb-Free) Industrial
30 CY7C136-30JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-30NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C136-30JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
35 CY7C136-35JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-35NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C136-35JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
45 CY7C136-45JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-45NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C136-45JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
55 CY7C136-55JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C136-55JXC 52-Pin Plastic Leaded Chip Carrier (Pb-Free)
CY7C136-55NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C136-55NXC 52-Pin Plastic Quad Flatpack (Pb-Free)
CY7C136-55JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
CY7C136A-55JXI 52-Pin Plastic Leaded Chip Carrier (Pb-Free)
CY7C136-55NI 51-85042 52-Pin Plastic Quad Flatpack
CY7C136A-55NXI 52-Pin Plastic Quad Flatpack (Pb-Free)
15 CY7C146-15JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-15NC 51-85042 52-Pin Plastic Quad Flatpack
25 CY7C146-25JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-25JXC 52-Pin Plastic Leaded Chip Carrier (Pb-Free)
CY7C146-25NC 51-85042 52-Pin Plastic Quad Flatpack
30 CY7C146-30JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-30NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C146-30JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
35 CY7C146-35JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-35NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C146-35JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
45 CY7C146-45JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-45NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C146-45JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
55 CY7C146-55JC 51-85004 52-Pin Plastic Leaded Chip Carrier Commercial
CY7C146-55JXC 52-Pin Plastic Leaded Chip Carrier (Pb-Free)
CY7C146-55NC 51-85042 52-Pin Plastic Quad Flatpack
CY7C146-55JI 51-85004 52-Pin Plastic Leaded Chip Carrier Industrial
[+] Feedback
Document #: 38-06031 Rev. *E Revised March 24, 2009 Page 15 of 15
All products and company names mentioned in this document may be the trademarks of their respective holders.
CY7C132, CY7C136
CY7C136A, CY7C142, CY7C146
© Cypress Semiconductor Corporation, 2005-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, li fe support, life saving, crit ica l con tr ol o r safe ty applications, un l ess p ur sua nt to an expre ss wr itten agreement with Cypress. Furthermore, Cyp r ess d oe s no t a uth or iz e its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright law s and i ntern atio nal t reaty p rovi sions. Cypr ess her eby gr ant s to li censee a per sonal , non- exclu sive, n on-transferable license to copy, use, modify , create derivative works of ,
and compile the Cypress Source Co de and derivative works for the sole p urpose of creating custo m software and or firmware in support of l icensee product to be used only in conjun ction with a Cypress
integrated ci rcuit as speci fied in the app licable agreem ent. Any reprod uction, modifi cation, transla tion, compila tion, or represent ation of th is Source Code exce pt as specified above is prohibited without
the express written perm i ssion of Cypr ess.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTAB ILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress re serves the right to make cha nges without further notice to the materials described herein. Cypress does not
assume any liabili ty ar ising ou t of the ap plicati on or u se o f any prod uct or c ircuit descri bed h erein. Cypress d oes not aut horize its pro duct s for use a s critical compo nent s in life-support systems whe re
a malfunctio n or failure may reasonab ly be expected to result in significant injury t o the user. T he inclusion of Cypres s’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document History Page
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC psoc.cypress.com
Clocks & Buffers clocks.cypress.com
Wireless wireless.cypress.com
Memories memory.cypress.com
Image Sensors image.cypress.com
PSoC Solutions
General psoc.cypress.com/solutions
Low Power/Low Voltage psoc.cypress.com/low-power
Precision Analog psoc.cypress.com/precision-analog
LCD Drive psoc.cypress.com/lcd-drive
CAN 2.0b psoc.cypress.com/can
USB psoc.cypress.com/usb
Document Title: CY7C132, CY7C136, CY7C136A, CY7C142, CY7C146 2K x 8 Dual-Port Static RAM
Document Number: 38-06031
Revision ECN Submission
Date Orig. of
Change Description of Change
** 110171 10/21/01 SZV Change from Spec number: 38-06031
*A 128959 09/03/0 3 JFU Added CY7C136-55NI to Order Information
*B 236748 See ECN YDT Removed cross information from features section
*C 39 3184 See ECN YIM Added Pb-Free Logo
Added Pb-Free parts to ordering information:
CY7C136-25JXC, CY7C136-25NXC, CY7C136-55JXC, CY7C136-55 NXC,
CY7C136-55JXI, CY7C136-55NXI, CY7C14 6-25JXC, CY7C146-55JXC
*D 2623658 12/17/08 VKN/PYRS Added CY7C136-2 5JXI part
Removed CY7C132/142 from the Ordering information table
Removed 48-Pin DIP and 52-Pin Square LCC package from the data sheet
*E 2678221 03/24/2009 VKN/AESA Added CY7C136A-55JXI, and CY7C136A-55NXI parts.
[+] Feedback
