3
PI49FCT3805/PI49FCT3806
3.3V Fast CMOS Buer/Clock Driver
www.pericom.com PS7007J 02/16/10
Storage Temperature ................................................................–65°C to +150°C
Ambient Temperature with Power Applied .......................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) ....–0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & I/O Only) .–0.5V to +7.0V
DC Input Voltage ........................................................................–0.5V to +7.0V
DC Output Current ................................................................................ 120 mA
Power Dissipation ........................................................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. is is
a stress rating only and functional operation of the device
at these or any other conditions above those indicated in
the operational sections of this specication is not implied.
Exposure to absolute maximum rating conditions for
extended periods may aect reliability.
Electrical Specifications
Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics (TA = –40°C to +85°C, VCC = 3.3V ±0.3V)
Symbol Parameter Test Condition(1) Min. Typ. Max. Units
VOH Output High Voltage
VCC = 3.0V, VIN = VIL or VIH
VCC = Min.,
VIN = VIH or VIL
IOH = -0.1mA
IOH = -8mA
VCC -0.2
2.4 (3)
-
3.0
V
VOL Output Low Voltage
VCC = 3.0V, VIN = VIL or VIH
VCC = Min.,
VIN = VIH or VIL
IOL = 0.1mA
IOL = 16mA
IOL = 24mA
-
0.2
0.3
0.2
0.4
0.5
VIH Input High Voltage Guaranteed Logic
HIGH level Input Pins 2.0 5.5
VIL Input Low Voltage Guaranteed Logic
LOW level Input Pins -0.5 0.8
IIH Input High Current VCC = Max VIN = VCC
(Input Pins) -1 1
µA
IIL Input Low Current VCC = Max
VIN = GND
(Input & I/O
Pins)
-1 1
IOZH High Impedance Output
Current
VCC = Max.,
All outputs Disabled
VOUT = VCC
VOUT = GND -1 1
IOZL High Impedance Output
Current
VCC = Max.,
All outputs Disabled
VOUT = VCC
VOUT = GND -1 1
VIK Clamp Diode Voltage VCC = Min., IIN = -18mA -0.7 -1.2 V
IODH Output HIGH Current VOUT = 3.3V, VIN =VIL or VIH,
VOUT = 1.5V(4) -35 -86 -110
mA
IODL Output LOW Current VOUT = 3.3V, VIN = VIL or VIH,
VOUT = 1.5V(4) 50 168 200
IOS Short Circuit
Current VCC = Max., VOUT = GND
-60 -135 -240
VHInput Hysteresis 150 mV
1. For Max. or Min. conditions, use appropriate value specied under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, +25°C ambient and maximum loading.
3. VOH = VCC – 0.6V at rated current.
4. is parameter is determined by device characterization but is not production tested.
5. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.