METALLIZED POLYPROPYLENE PLASTIC CASE, QUICK DISCONNECT CAPACITORS 970A SERIES (R) The 970A Series Snubber Capacitors were designed for AC applications such as motor start, motor run, fluorescent lamp ballast and other commercial applications. A wide range of rectangular epoxy case sizes are available with quick disconnect terminals. Wrap and fill designs are also available on special order. Extended metallized polypropylene is used as the dielectric material. Electrocube recognizes and supports the circuit design needs for specific mounting configurations, voltages and capacitances for capacitor models not shown. Special designs can be manufactured to meet any existing or future requirement. For specific information on your product needs, contact your local sales representative or Electrocube directly. The potting material and epoxy endfills of Electrocube's capacitors meet or exceed the flammability requirements of UL94VO. Dimensional variations for all MFD values are available with the same volume to meet your design requirements. SPECIFICATIONS Dielectric Voltage Test: Will withstand the application of 175% rated DC voltage for a period not to exceed 1 minute at 25C; current limited to 5 mA. DC Life Test: Will withstand the application of 125% rated VDC at 85C for 1000 hours, with not more than 1 failure in 12 permitted; current limited to 5 mA TYPICAL DIELECTRIC CHARACTERISTIC CURVES % CAPACITANCE CHANGE Capacitance Tolerance: 10% Temperature: -55C to +70C at rated voltage Dissipation Factor: Shall not exceed .20% at 25C. Acceptance Criteria: Measurement frequency for capacitance Insulation Resistance: At rated voltage or 500V, whichever is less, units shall meet the minimum values below: 1.0K % DISSIPATION FACTOR and dissipation factor shall be 120 Hz. NOTES: For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory. For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including higher IR or lower DF), consult the factory direct. The 970A Series film capacitors have epoxy fill and enclosures that meet or exceed the flammability requirements of UL94V0. INSULATION RESISTANCE (MEGOHMS TIMES MICROFARADS) Terminals: 1/4" Quick Disconnect terminals 3366 Pomona Blvd. * Pomona, CA 91768 * TEL: (909) 595-4037 * FAX: (909) 595-0186 e-mail: esales@electrocube.com * Internet: www.electrocube.com * (IR: 10/03)(R)(R) METALLIZED POLYPROPYLENE PLASTIC CASE, QUICK DISCONNECT CAPACITORS 970A SERIES (R) .18 DIA. L MAX. FASTON TERMINALS .25" T MAX. H MAX. 250VAC 0 330VAC DIMENSIONS MFD CAP CODE L 1.0 105 1.5 370VAC DIMENSIONS 440VAC DIMENSIONS H T D L H T D L 1.26 .91 .51 .18 1.26 .91 .51 .18 155 1.26 .91 .51 .18 1.50 .91 .55 2.0 205 1.26 .91 .51 .18 1.50 .98 2.5 255 1.50 .87 .51 .18 1.50 3.0 305 1.50 .87 .51 .18 3.5 355 1.50 .91 .55 4.0 405 1.50 1.06 5.0 505 1.50 6.0 605 7.0 DIMENSIONS H T D L 1.50 .87 .51 .18 1.50 .18 1.46 1.06 .59 .18 .59 .18 1.50 1.10 .71 1.10 .71 .18 1.50 1.18 1.50 1.18 .79 .18 1.50 .18 1.50 1.26 .91 .18 .59 .18 1.89 1.18 .79 1.02 .63 .18 1.89 1.18 1.50 1.10 .71 .18 1.89 705 1.50 1.18 .79 .18 8.0 805 1.50 1.18 .79 9.0 905 1.89 1.18 10.0 106 1.89 12.0 126 15.0 20.0 H T D .87 .51 .18 1.46 1.06 .59 .18 .18 1.50 1.10 .71 .18 .79 .18 1.50 1.18 .79 .18 1.26 .91 .18 1.50 1.26 .91 .18 1.89 1.18 .79 .18 1.89 1.18 .79 .18 .18 1.89 1.26 .91 .18 1.89 1.26 .91 .18 .79 .18 1.89 1.46 1.02 .18 1.89 1.46 1.02 .18 1.26 .91 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - 1.89 1.46 1.02 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - .18 1.89 1.46 1.02 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - .79 .18 2.01 1.58 1.18 .18 2.28 1.58 1.18 .18 2.28 1.58 1.18 - 1.26 .91 .18 2.01 1.58 1.18 .18 - - - - - - - - 1.89 1.46 1.02 .18 2.28 1.58 1.18 .18 - - - - - - - - 156 1.89 1.46 1.02 .18 - - - - - - - - - - - - 206 2.01 1.58 1.18 .18 - - - - - - - - - - - - ORDERING INFORMATION 970A 1 CAPACITANCE SERIES NUMBER AND CASE STYLE DESIGNATION * *** * CIRCUIT SYMBOL 1 -- FLOATING CASE TOLERANCE K -- 10% CAPACITANCE CODE VOLTAGE E -- 250VAC F -- 330VAC W -- 370VAC X -- 440VAC 3366 Pomona Blvd. * Pomona, CA 91768 * TEL: (909) 595-4037 * FAX: (909) 595-0186 e-mail: esales@electrocube.com * Internet: www.electrocube.com * (IR: 10/03)(R)(R) METALLIZED POLYPROPYLENE PLASTIC CASE, QUICK DISCONNECT CAPACITORS 971A SERIES (R) The 971A Series Snubber Capacitors were designed for AC applications such as motor start, motor run, fluorescent lamp ballast and other commercial applications. A wide range of rectangular epoxy case sizes are available with quick disconnect terminals. Wrap and fill designs are also available on special order. Extended metallized polypropylene is used as the dielectric material. Electrocube recognizes and supports the circuit design needs for specific mounting configurations, voltages and capacitances for capacitor models not shown. Special designs can be manufactured to meet any existing or future requirement. For specific information on your product needs, contact your local sales representative or Electrocube directly. The potting material and epoxy endfills of Electrocube's capacitors meet or exceed the flammability requirements of UL94VO. Dimensional variations for all MFD values are available with the same volume to meet your design requirements. SPECIFICATIONS Dielectric Voltage Test: Will withstand the application of 175% rated DC voltage for a period not to exceed 1 minute at 25C; current limited to 5 mA. DC Life Test: Will withstand the application of 125% rated VDC at 85C for 1000 hours, with not more than 1 failure in 12 permitted; current limited to 5 mA TYPICAL DIELECTRIC CHARACTERISTIC CURVES % CAPACITANCE CHANGE Capacitance Tolerance: 10% Temperature: -55C to +70C at rated voltage Dissipation Factor: Shall not exceed .20% at 25C. Acceptance Criteria: Measurement frequency for capacitance Insulation Resistance: At rated voltage or 500V, whichever is less, units shall meet the minimum values below: 1.0K % DISSIPATION FACTOR and dissipation factor shall be 120 Hz. NOTES: For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory. For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including higher IR or lower DF), consult the factory direct. The 971A Series film capacitors have epoxy fill and enclosures that meet or exceed the flammability requirements of UL94V0. INSULATION RESISTANCE (MEGOHMS TIMES MICROFARADS) Terminals: 1/4" Quick Disconnect terminals 3366 Pomona Blvd. * Pomona, CA 91768 * TEL: (909) 595-4037 * FAX: (909) 595-0186 e-mail: esales@electrocube.com * Internet: www.electrocube.com * (IR: 10/03)(R)(R) METALLIZED POLYPROPYLENE PLASTIC CASE, QUICK DISCONNECT CAPACITORS 971A SERIES (R) .18 DIA. L MAX. FASTON TERMINALS .25" T MAX. H MAX. MFD CAP CODE L 1.0 105 1.5 250VAC 330VAC 370VAC 440VAC DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONS H T D L H T D L H T D L 1.26 .91 .51 .18 1.26 .91 .51 .18 1.50 .87 .51 .18 1.50 155 1.26 .91 .51 .18 1.50 .91 .55 .18 1.46 1.06 .59 .18 2.0 205 1.26 .91 .51 .18 1.50 .98 .59 .18 1.50 1.10 .71 2.5 255 1.50 .87 .51 .18 1.50 1.10 .71 .18 1.50 1.18 3.0 305 1.50 .87 .51 .18 1.50 1.18 .79 .18 1.50 3.5 355 1.50 .91 .55 .18 1.50 1.26 .91 .18 4.0 405 1.50 1.06 .59 .18 1.89 1.18 .79 5.0 505 1.50 1.02 .63 .18 1.89 1.18 6.0 605 1.50 1.10 .71 .18 1.89 7.0 705 1.50 1.18 .79 .18 8.0 805 1.50 1.18 .79 9.0 905 1.89 1.18 10.0 106 1.89 12.0 126 15.0 20.0 H T D .87 .51 .18 1.46 1.06 .59 .18 .18 1.50 1.10 .71 .18 .79 .18 1.50 1.18 .79 .18 1.26 .91 .18 1.50 1.26 .91 .18 1.89 1.18 .79 .18 1.89 1.18 .79 .18 .18 1.89 1.26 .91 .18 1.89 1.26 .91 .18 .79 .18 1.89 1.46 1.02 .18 1.89 1.46 1.02 .18 1.26 .91 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - 1.89 1.46 1.02 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - .18 1.89 1.46 1.02 .18 2.01 1.58 1.18 .18 2.01 1.58 1.18 - .79 .18 2.01 1.58 1.18 .18 2.28 1.58 1.18 .18 2.28 1.58 1.18 - 1.26 .91 .18 2.01 1.58 1.18 .18 - - - - - - - - 1.89 1.46 1.02 .18 2.28 1.58 1.18 .18 - - - - - - - - 156 1.89 1.46 1.02 .18 - - - - - - - - - - - - 206 2.01 1.58 1.18 .18 - - - - - - - - - - - - ORDERING INFORMATION 971A 1 CAPACITANCE SERIES NUMBER AND CASE STYLE DESIGNATION * *** * CIRCUIT SYMBOL 1 -- FLOATING CASE TOLERANCE K -- 10% CAPACITANCE CODE VOLTAGE E -- 250VAC F -- 330VAC W -- 370VAC X -- 440VAC 3366 Pomona Blvd. * Pomona, CA 91768 * TEL: (909) 595-4037 * FAX: (909) 595-0186 e-mail: esales@electrocube.com * Internet: www.electrocube.com * (IR: 10/03)(R)(R)