Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 1 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
Features
Industry Standard Serial ATA (SATA) Host
Interface
- SATA 1.5 Gb/s or SATA 3.0 Gb/s 1)
- ATA/ATAPI-8 compliant
- Supports 48-bit address feature set
Performance
- Sequential data read:
Up to 70 MByte/sec*
- Sequential data write:
Up to 60 MByte/sec*
* measured using 128 KByte transfer size
Power Management
- 3.3V and 1.2Vpower supply
- Host SATA interface power management
- Immediate disabling of unused circuitry
without host intervention
Power Specifications 2)
- Active mode:
750mW typical (GLS85LS1008P)
560mW typical (GLS85LS1004P)
450mW typical (GLS85LS1002P)
- Idle / Standby mode: 210mW typical
- Sleep mode: 70mW typical
Integrated Voltage Detector
- Detects supply voltage fluctuations and
generates reset during power-up and power-
down to prevent inadvertent writes
Supports SMART Commands
Expanded Data Protection
- Added data security through user-selectable
protection zones
20-Byte Serial Number
- Factory pre-programmed 10-Byte unique ID
- User-programmable 10-Byte ID
Robust Built-in ECC
NAND Configuration
- 1 bit per cell (SLC)
Industrial Temperature Range
- -40°C to 85°C
FBGA package
- 14.0 mm x 24.0 mm x 1.95 mm, 145-ball,
1.0 mm ball pitch, FZJE
All Devices are RoHS Compliant
1) Current product revision supports SATA Revision 1.x with
host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s).
SATA 3.0 Gb/s refers to SATA Revision 2.x and will be
supported by our planned future product revisions.
2) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
Product Description
The GLS85LS1002P / 1004P / 1008P Industrial Grade
SATA NANDrive™ devices (referred to as “SATA
NANDrive” in this fact sheet) are fully integrated solid
state drives. They combine an advanced Greenliant
NAND controller and 2, 4 or 8 GByte of NAND flash in
a multi-chip package. These products are ideal for
embedded and portable applications that require
smaller form-factor and more reliable data storage.
SATA-interface solid state mass storage technology is
widely used in portable and industrial computers, set-
top boxes, multi-functional printers, point-of-sales
terminals, video and audio recorders, medical
instruments and car infotainment systems.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
The integrated NAND flash controller with built-in
advanced NAND management firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
SATA NANDrive devices are offered in a 145-ball
BGA, 1 mm ball pitch package.
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 2 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
1.0 GENERAL DESCRIPTION
Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete
NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram.
1.1 Optimized SATA NANDrive
The heart of SATA NANDrive is the SATA NAND flash
memory controller which translates standard SATA
signals into flash media data and control signals. The
following components contribute to SATA NANDrive’s
operation.
1.1.1 Microcontroller Unit (MCU)
The MCU translates SATA commands into data and
control signals required for flash media operation.
1.1.2 Internal Direct Memory Access (DMA)
SATA NANDrive uses internal DMA allowing instant
data transfer from/to buffer to/from flash media. This
implementation eliminates microcontroller overhead
associated with the traditional, firmware-based
approach, thereby increasing the data transfer rate.
1.1.3 Power Management Unit (PMU)
The PMU controls the power consumption of SATA
NANDrive. The PMU dramatically reduces the power
consumption of SATA NANDrive by putting the part of
the circuitry that is not in operation into sleep mode. 3)
The Flash File System handles inadvertent power
interrupts and has auto-recovery capability to ensure
SATA NANDrive firmware integrity. For regular power
management, the host must send a
STANDBY_IMMEDIATE (E0h), IDLE_IMMEDIATE
(E1h), STANDBY (E2h) or IDLE (E3h) command and
wait for command ready before powering down SATA
NANDrive.
3) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
1.1.4 Embedded Flash File System
The embedded flash file system is an integral part of
SATA NANDrive. It contains MCU firmware that
performs the following tasks:
1. Translates host side signals into flash media
writes and reads
2. Provides flash media wear leveling to spread the
flash writes across all memory address space to
increase the longevity of flash media
3. Keeps track of data file structures
4. Manages system security for the selected
protection zones
1.1.5 Error Correction Code (ECC)
High performance is achieved through optimized
hardware error detection and correction.
1.1.6 Serial Communication Interface (SCI)
The Serial Communication Interface (SCI) is designed
for error reporting. During the product development
stage, it is recommended to provide the SCI port on
the PCB to aid in design validation.
1.1.7 Multi-tasking Interface
The multi-tasking interface enables fast, sequential
write performance by allowing concurrent Read,
Program and Erase operations to multiple flash media.
1.2 SMT Reflow Consideration
The SATA NANDrive family utilizes standard NAND
flash for data storage. Because the high temperature
in a surface-mount soldering reflow process may alter
the content on NAND flash, it is recommended to
program SATA NANDrive after the reflow process.
1.3 Advanced NAND Management
SATA NANDrive’s integrated controller uses
advanced wear-leveling algorithms to substantially
increase the longevity of NAND flash media. Wear
caused by data writes is evenly distributed in all or
select blocks in the device that prevents “hot spots” in
locations that are programmed and erased extensively.
This effective wear-leveling technique results in
optimized device endurance, enhanced data retention
and higher reliability required by long-life applications.
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 3 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
2.0 FUNCTIONAL BLOCKS
Figure 2-1: SATA NANDrive Block Diagram
Flash Media I/F
NAND I/F
NAND
Chips
NAND
Chips
NAND
Chips
Embedded Flash
File System
MCU
SATA I/F
Internal
DMA
SCI
PMU
Memory
Channel I/F
NAND Controller
ECC
SRAM Buffer
SATA ll
HOST I/F
3.0/1.5 Gbps
Memory
Channel I/F
ECC
NAND
Chips
NAND
Flash
SATA NANDrive
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 4 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
3.0 PRODUCT ORDERING INFORMATION
GLS 85 LS 1 0xxP - S - I - FZJE - NDxxx
XX XX X XXXX - X - X - XXXX - XXXXX
Ordering Code 4)
NDxxx = NANDrive revision
EDxxx = Evaluation Board revision
Environmental Attribute
E = non-Pb solder (RoHS Compliant)
Package Modifier
ZJ = 145-ball positions
Package Type
F = FBGA
Operation Temperature
I = Industrial: -40°C to +85°C
NAND Configuration
S = 1 bit per cell
Generation / Product Configuration
P = First generation
Capacity
002 = 2 GByte
004 = 4 GByte
008 = 8 GByte
MByte or GByte Designator
0 = MByte
1 = GByte
Interface
S = SATA
Voltage
L = 3.3V
Product Series
85 = NANDrive
4) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC
(custom specification) which is required by the end-customer to be marked on the device.
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 5 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
Valid Combinations
Valid product combinations are those that are in the mass production or will be in the mass production. Consult
your Greenliant sales representative to confirm availability of the valid combinations and to determine availability
of new product combinations.
Table 3-1: SATA NANDrive Product Valid Ordering Numbers
Capacity
Operating Temperature
Part Number
Package
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-FZJE
FZJE, 14x24x1.95mm
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-FZJE-ND104
FZJE, 14x24x1.95mm
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-FZJE
FZJE, 14x24x1.95mm
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-FZJE-ND104
FZJE, 14x24x1.95mm
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-FZJE
FZJE, 14x24x1.95mm
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-FZJE-ND101
FZJE, 14x24x1.95mm
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-FZJE-ND104
FZJE, 14x24x1.95mm
Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers
Capacity
Operating Temperature
Part Number
Form Factor
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-1S-K
Module with SATA connector
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-1S-ED104
Module with SATA connector
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-1S-K
Module with SATA connector
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-1S-ED104
Module with SATA connector
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1S-K
Module with SATA connector
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1S-ED101
Module with SATA connector
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1S-ED104
Module with SATA connector
Table 3-3: SATA NANDrive miniSATA Evaluation Board Valid Ordering Numbers
Capacity
Operating Temperature
Part Number
Form Factor
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-1MS-K
JEDEC MO-300
2GB
Industrial (-40°C to 85°C)
GLS85LS1002P-S-I-1MS-ED104
JEDEC MO-300
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-1MS-K
JEDEC MO-300
4GB
Industrial (-40°C to 85°C)
GLS85LS1004P-S-I-1MS-ED104
JEDEC MO-300
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1MS-K
JEDEC MO-300
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1MS-ED101
JEDEC MO-300
8GB
Industrial (-40°C to 85°C)
GLS85LS1008P-S-I-1MS-ED104
JEDEC MO-300
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 6 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
3.1 Package Diagram
TOP VIEW
11
10
9
8
7
6
5
4
3
2
1
A B C D E F G H J K L M N P R T U V W Y AA AB AC
24.0 ±0.1
BOTTOM VIEW
1
2
3
4
5
6
7
8
9
10
11
A B C D E F G H J K L M N P R T U V W Y AA AB AC
SIDE
VIEW
1mm
DETAIL
Note: All linear dimensions are in millimeters.
Untoleranced dimensions are nominal target values.
Coplanarity: 0.15 mm.
0.40 ±0.05 Ball opening size is 0.40 mm (± 0.05 mm).
1.80 ± 0.15
SEATING
PLANE
Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: FZJ
14.0
+/- 0.1
A1
CORNER
14.0
1.0
8.0
1.0
0.5 +/- 0.05
(145x)
0.15
3.0
Fact Sheet 03.001
May 2014
These specifications are subject to change without notice. 05/09/2014
© 2014 Greenliant Systems 7 S71432-F
GLS85LS1002P / 1004P / 1008P
Industrial Grade SATA NANDrive™
Revision History
Revision
Description
Date
01.000
Initial release of Fact Sheet for GLS85LS1002P/1004P/1008P
October 17, 2011
01.001
Updated Table 3-1
December 22, 2011
01.002
Corrected typo in Table 3-1
March 12, 2012
02.000
Added part numbers GLS85LS1016P/1032P and updated Section 1.2
April 9, 2012
02.100
Separated part numbers GLS85LS1016P/1032P to document S71445-F
Updated Table 3-1 and Section 4.0
January 18, 2013
02.101
Removed Table 3-1
April 17, 2013
02.200
Updated Power Specifications
Added information for part number GLS85LS1008P-S-I-FZJE-ND104
November 21, 2013
03.000
Added information for part numbers GLS85LS1002P-S-I-FZJE-ND104
and GLS85LS1004P-S-I-FZJE-ND104
February 25, 2014
03.001
Updated Section 1.1.3
May 09, 2014
© 2014 Greenliant Systems. All rights reserved.
Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant
Systems. All other trademarks and registered trademarks are the property of their respective owners.
Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable
capacity may be less.
Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant
Terms and Conditions of Sale.
www.greenliant.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Greenliant:
GLS85LS1008P-S-I-1S-K GLS85LS1004P-S-I-1MS-K GLS85LS1002P-S-I-1S-K GLS85LS1002P-S-I-FZJE
GLS85LS1004P-S-I-FZJE GLS85LS1004P-S-I-1S-K GLS85LS1002P-S-I-1MS-K GLS85LS1008P-S-I-FZJE-ND104
GLS85LS1032P-S-I-1S-ED101 GLS85LS1016P-S-I-1MS-ED101 GLS85LS1002P-S-I-FZJE-ND104 GLS85LS1008P-S-
I-1S-ED101 GLS85LS1032P-S-I-FZJE-ND104 GLS85LS1032P-S-I-1MS-ED101
