CM1215 1, 2 and 4-Channel Low Capacitance ESD Arrays Product Description http://onsemi.com The CM1215 family of diode arrays provides ESD protection for electronic components or sub-systems requiring minimal capacitive loading. These devices are ideal for protecting systems with high data and clock rates or for circuits requiring low capacitive loading. Each ESD channel consists of a pair of diodes in series which steer the positive or negative ESD current pulse to either the positive (VP) or negative (VN) supply rail. The CM1215 protects against ESD pulses up to 15 kV per the IEC 61000-4-2 standard. This device is particularly well-suited for protecting systems using high-speed ports such as USB2.0, IEEE1394 (Firewire(R), iLinkt), Serial ATA, DVI, HDMI and corresponding ports in removable storage, digital camcorders, DVD-RW drives and other applications where extremely low loading capacitance with ESD protection are required in a small package footprint. SOT23-3 SO SUFFIX CASE 419AH SOT23-5 SO SUFFIX CASE 527AH SOT23-6 SO SUFFIX CASE 527AJ MARKING DIAGRAM Features * One, two, and four channels of ESD Protection * Provides 15 kV ESD Protection on Each Channel Per the IEC * * * * * * * SOT143 SR SUFFIX CASE 527AF 61000-4-2 ESD Requirements Channel Loading Capacitance of 1.6 pF Typical Channel I/O to GND Capacitance Difference of 0.04 pF Typical Mutual Capacitance of 0.13 pF Typical Minimal Capacitance Change with Temperature and Voltage Each I/O Pin Can Withstand Over 1000 ESD Strikes SOT Packages These Devices are Pb-Free and are RoHS Compliant Applications * IEEE1394 Firewire(R) Ports at 400 Mbps / 800 Mbps * DVI Ports, HDMI Ports in Notebooks, Set Top Boxes, Digital TVs, LCD Displays * Serial ATA Ports in Desktop PCs and Hard Disk Drives * PCI Express Ports * General Purpose High-Speed Data Line ESD Protection E151 MG G E152 MG G E153 MG G E154 MG G 1 1 1 XXXX = Specific Device Code M = Date Code G = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION Device Package Shipping CM1215-01SO SOT23-3 (Pb-Free) 3000/Tape & Reel CM1215-02SR SOT143 (Pb-Free) 3000/Tape & Reel CM1215-02SO SOT23-5 (Pb-Free) SOT23-6 (Pb-Free) 3000/Tape & Reel CM1215-04SO 3000/Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2011 July, 2011 - Rev. 3 1 Publication Order Number: CM1215/D CM1215 BLOCK DIAGRAM VP VP CH1 CH4 CH1 VN CM1215-01SO VP CH3 CH2 VN CM1215-02SO CM1215-02SR CH1 VN CH2 CM1215-04SO PACKAGE / PINOUT DIAGRAMS Top View CH1 VN 1 CH1 3-Pin SOT23-3 2 CH2 3 4-Pin SOT143 NC 1 VN 2 CH1 3 5 VP 4 CH2 5-Lead SOT23-5 CH1 1 VN 2 CH2 3 E154 VN 2 VP 4 Top View E153 3 1 Top View E152 E151 VP Top View 6 CH4 5 VP 4 CH3 6-Pin SOT23-6 Table 1. PACKAGE PIN DESCRIPTIONS SOT23-3 SOT143 SOT23-5 SOT23-6 Pin Name Pin No. Pin No. Pin No. Pin No. Type CH1 1 2 3 1 I/O Description ESD Channel VN 3 1 2 2 GND CH2 - 3 4 3 I/O ESD Channel CH3 - - - 4 I/O ESD Channel VP 2 4 5 5 PWR CH4 - - - 6 I/O ESD Channel N/C - - 1 - - No Connection http://onsemi.com 2 Negative voltage supply rail Positive voltage supply rail CM1215 SPECIFICATIONS Table 2. ABSOLUTE MAXIMUM RATINGS Parameter Rating Units Operating Supply Voltage (VP-VN) 6 V Diode Forward DC Current (Note 1) 20 mA (VN-0.5) to (VP+0.5) V Ambient -40 to +85 C Junction -40 to +125 C Storage Temperature Range -40 to +150 C DC Voltage at any Channel Input Operating Temperature Range Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 3. STANDARD OPERATING CONDITIONS Parameter Operating Temperature Range Rating Units -40 to +85 C Package Power Rating SOT23-3 Package (CM1215-01SO) SOT143 Package (CM1215-02SR) SOT23-5 Package (CM1215-02SO) SOT23-6 Package (CM1215-04SO) mW 225 225 225 225 Table 4. ELECTRICAL OPERATING CHARACTERISTICS (Note 1) Symbol Parameter Conditions VP Operating Supply Voltage (VP-VN) IP Operating Supply Current (VP-VN) = 3.3 V VF Diode Forward Voltage Top Diode Bottom Diode IF = 20 mA; TA = 25C Channel Leakage Current Channel Input Capacitance ILEAK CIN CIN CMUTUAL VESD VCL RDYN Min 0.6 0.6 Typ Max Unit 3.3 5.5 V 8 mA V 0.8 0.8 0.95 0.95 TA = 25C; VP = 5 V, VN = 0 V 0.1 1.0 mA At 1 MHz, VP = 3.3 V, VN = 0 V, VIN = 1.65V; 1.6 2.0 pF Channel I/O to GND Capacitance Difference Mutual Capacitance (VP-VN) = 3.3 V ESD Protection Peak Discharge Voltage at any channel input, in system, contact discharge per IEC 61000-4-2 standard TA = 25C (Notes 2 and 3) Channel Clamp Voltage Positive Transients Negative Transients IPP = 1 A, tP = 8/20 mS; TA = 25C; Dynamic Resistance Positive transients Negative transients IPP = 1 A, tP = 8/20 mS; TA = 25C; 1. All parameters specified at TA = -40C to +85C unless otherwise noted. 2. Standard IEC 61000-4-2 with CDischarge = 150 pF, RDischarge = 330 W, VP = 3.3 V, VN grounded. 3. From I/O pins to VP or VN only. VP bypassed to VN with low ESR 0.2 mF ceramic capacitor. http://onsemi.com 3 0.04 pF 0.13 pF kV 15 VP+1.5 VN-1.5 0.4 0.4 V W CM1215 PERFORMANCE INFORMATION Input Channel Capacitance Performance Curves Figure 1. Typical Variation of CIN vs. VIN (f = 1 MHz, VP= 3.3 V, VN = 0 V, 0.1 mF Chip Capacitor between VP and VN, TA = 255C) Figure 2. Typical Filter Performance (Nominal Conditions unless Specified Otherwise, 50 Ohm Environment) http://onsemi.com 4 CM1215 APPLICATION INFORMATION Design Considerations In order to realize the maximum protection against ESD pulses, care must be taken in the PCB layout to minimize parasitic series inductances on the Supply/ Ground rails as well as the signal trace segment between the signal input (typically a connector) and the ESD protection device. Refer to Figure 1, which illustrates an example of a positive ESD pulse striking an input channel. The parasitic series inductance back to the power supply is represented by L1 and L2. The voltage VCL on the line being protected is: VCL = Fwd voltage drop of D1 + VSUPPLY + L1 x d(IESD) / dt+ L2 x d(IESD) / dt where IESD is the ESD current pulse, and VSUPPLY is the positive supply voltage. An ESD current pulse can rise from zero to its peak value in a very short time. As an example, a level 4 contact discharge per the IEC61000-4-2 standard results in a current pulse that rises from zero to 30 Amps in 1ns. Here d(IESD)/dt can be approximated by d(ESD)/dt, or 30/(1x10-9). So just 10 nH of series inductance (L1 and L2 combined) will lead to a 300 V increment in VCL! Similarly for negative ESD pulses, parasitic series inductance from the VN pin to the ground rail will lead to drastically increased negative voltage on the line being protected. As a general rule, the ESD Protection Array should be located as close as possible to the point of entry of expected electrostatic discharges. The power supply bypass capacitor mentioned above should be as close to the VP pin of the Protection Array as possible, with minimum PCB trace lengths to the power supply, ground planes and between the signal input and the ESD device to minimize stray series inductance. Additional Information See also ON Semiconductor Application Note, "Design Considerations for ESD Protection", in the Applications section. L1 POSITIVE SUPPLY PATH OF ESD CURRENT PULSE (IESD) D1 C1 LINE BEING PROTECTED ONE CHANNEL D2 SYSTEM OR CIRCUITRY BEING PROTECTED CHANNEL IMPUT GROUND RAIL CHASSI`S GROUND Figure 3. Application of Positive ESD Pulse between Input Channel and Ground http://onsemi.com 5 CM1215 PACKAGE DIMENSIONS SOT-23 3-Lead (TO-236AA) CASE 419AH-01 ISSUE O D 3X b L2 3 GAUGE PLANE E1 E 1 L 2 e e C DETAIL Z A SEATING PLANE M DIM A A1 b c D E E1 e L L2 M c 0.05 C A1 SEATING PLANE DETAIL Z RECOMMENDED SOLDERING FOOTPRINT* 3X 0.56 2.74 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSIONS D AND E1 ARE DETERMINED AT DATUM H. 5. PIN ONE INDICATOR MUST BE LOCATED IN THE INDICATED ZONE. 3X 0.82 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 MILLIMETERS MIN MAX 0.75 1.17 0.05 0.15 0.30 0.50 0.08 0.20 2.80 3.05 2.10 2.64 1.20 1.40 0.95 BSC 0.40 0.60 0.25 BSC 0 8 CM1215 PACKAGE DIMENSIONS SOT-143, 4 Lead CASE 527AF-01 ISSUE A SYMBOL MIN A 0.80 1.22 D A1 0.05 0.15 e A2 0.75 b 0.30 0.50 b2 0.76 0.89 4 3 E1 1 E c 0.08 D 2.80 E 2.10 E1 1.20 e 2 0.40 L1 2.64 1.30 0.50 0 A1 L1 SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC TO-253. http://onsemi.com 7 0.60 c L b2 1.40 8 q A 3.04 0.25 A2 0.20 2.90 0.54 REF L2 TOP VIEW 1.07 0.20 BSC L b 0.90 MAX 1.92 BSC e1 e1 NOM L2 CM1215 PACKAGE DIMENSIONS SOT-23, 5 Lead CASE 527AH-01 ISSUE O D E1 SYMBOL MIN A 0.90 A1 0.00 A2 0.90 b 0.30 0.50 c 0.08 0.22 E 0.15 1.15 D 2.90 BSC E 2.80 BSC 1.60 BSC e 0.95 BSC L MAX 1.45 E1 e PIN #1 IDENTIFICATION NOM 0.45 0.30 L1 0.60 REF L2 0.25 REF 1.30 0.60 0 4 8 1 5 10 15 2 5 10 15 TOP VIEW 1 A2 A b 2 L1 A1 SIDE VIEW L2 L END VIEW Notes: (1) All dimensions in millimeters. Angles in degrees. (2) Complies with JEDEC standard MO-178. http://onsemi.com 8 c CM1215 PACKAGE DIMENSIONS SOT-23, 6 Lead CASE 527AJ-01 ISSUE A D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DATUM C IS THE SEATING PLANE. B 6 5 4 1 2 3 E E GAGE PLANE 6X e TOP VIEW L2 b 0.20 SEATING PLANE L M C A S B S DETAIL A A2 0.10 C A1 C SIDE VIEW MILLIMETERS MIN MAX --1.45 0.00 0.15 0.90 1.30 0.20 0.50 0.08 0.26 2.70 3.00 2.50 3.10 1.30 1.80 0.95 BSC 0.20 0.60 0.25 BSC c A 6X DIM A A1 A2 b c D E E1 e L L2 DETAIL A SEATING PLANE END VIEW RECOMMENDED SOLDERING FOOTPRINT* 3.30 6X 0.85 6X 0.56 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. FireWire is a registered trademark of Apple Computer, Inc. iLink is a trademark of S. J. Electro Systems, Inc. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CM1215/D