JILI30 Development KTD-S0018-0 User Information Table of Contents Table of Contents 1 User Information .....................................................................................1 1.1 About This Document ................................................................................................................. 1 1.2 Copyright Notice ....................................................................................................................... 1 1.3 Trademarks .............................................................................................................................. 1 1.4 Standards ................................................................................................................................ 1 1.5 Warranty.................................................................................................................................. 1 1.6 Life Support Policy..................................................................................................................... 2 1.7 Technical Support...................................................................................................................... 2 2 Introduction ...........................................................................................3 2.1 JILI30 Specification ................................................................................................................... 3 2.2 JILI30 Cable Overview ................................................................................................................ 3 2.3 KAB-ADAPT-LVDStoTTL Accessories ............................................................................................... 3 3 JILI30 Connector (SBC Side) ......................................................................4 4 JILI30 Cable (Examples)............................................................................5 4.1 KAB-JILI30-TXLD03 ................................................................................................................... 5 4.1.1 4.1.2 4.1.3 Display Connector Pinout ............................................................................................................................ 6 Display Connector...................................................................................................................................... 6 Cable Wiring ............................................................................................................................................. 7 4.2 KAB-JILI30-TELD02 ................................................................................................................... 7 4.2.1 4.2.2 4.2.3 Display Connector Pinout ............................................................................................................................ 8 Display Connector...................................................................................................................................... 8 Cable Wiring ............................................................................................................................................. 9 5 KAB-ADAPT-LVDStoTTL ............................................................................ 10 5.1 JILI30 Connector..................................................................................................................... 10 5.2 FLEX32 Connector.................................................................................................................... 11 5.3 Power Supply .......................................................................................................................... 12 5.3.1 5.3.2 Panel Power +3.3V ....................................................................................................................................12 Panel Power +5.0V ....................................................................................................................................12 5.4 FLEX32 Configurable Pins .......................................................................................................... 13 5.5 Electrical Specifications ............................................................................................................ 13 6 FLEX32 Cable (Example) .......................................................................... 14 6.1 KAB-FLEX32-TVDD04 ................................................................................................................ 14 6.1.1 6.1.2 6.1.3 Display Connector Pinout ...........................................................................................................................14 Display Connector.....................................................................................................................................15 Cable Wiring ............................................................................................................................................15 Appendix A: Schematic KAB-ADAPT-LVDStoTLL ....................................................... 16 Appendix B: Document Revision History................................................................ 17 Display Cable Guide KTD-S0018-0 1 User Information 1.1 About This Document Page 1 User Information This document provides information about products from KONTRON Technology A/S and/or its subsidiaries. No warranty of suitability, purpose or fitness is implied. While every attempt has been made to ensure that the information in this document is accurate the information contained within is supplied "as-is" - no liability is taken for any inaccuracies. Manual is subject to change without prior notice. KONTRON assumes no responsibility for the circuits, descriptions and tables indicated as far as patents or other rights of third parties are concerned. 1.2 Copyright Notice Copyright (c) 2005 - 2010, KONTRON Technology A/S, ALL RIGHTS RESERVED. No part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanically, for any purpose without the express written permission of KONTRON Technology A/S. 1.3 Trademarks Brand and product names are trademarks or registered trademarks of their respective owners. 1.4 Standards KONTRON Technology A/S is certified to ISO 9000 standards. 1.5 Warranty This product is warranted against defects in material and workmanship for the warranty period from the date of shipment. During the warranty period KONTRON Technology A/S will at its discretion decide to repair or replace defective products. Within the warranty period the repair of products is free of charge as long as warranty conditions are observed. The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer, unauthorized modification or misuse, operation outside of the product's environmental specifications or improper installation or maintenance. KONTRON Technology A/S will not be responsible for any defects or damages to third party products that are caused by a faulty KONTRON Technology A/S product. Display Cable Guide KTD-S0018-0 1.6 Page 2 User Information Life Support Policy KONTRON Technology's products are not for use as critical components in life support devices or systems without express written approval of the general manager of KONTRON Technology A/S. As used herein: Life support devices or systems are devices or systems which a) are intended for surgical implant into body or b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labelling, can be reasonably expected to result in significant injury to the user. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. 1.7 Technical Support Please consult our web site at http://www.kontron.com/support for the latest product documentation, utilities, drivers and support contacts. In any case you can always contact your board supplier for technical support. Before contacting support please be prepared to provide as much information as possible: Cable/Adapter identification: E Type E Part number (find PN on label) E Attached hardware (LCD panels ...) Display Cable Guide KTD-S0018-0 Page 3 2 Introduction 2.1 JILI30 Specification Introduction The SBCs (Single Board Computer) from KONTRON Technology A/S only support the JILI30 LVDS interface. JILI30 is a KONTRON hardware standard that interfaces a SBC via a LVDS connection to flatpanel displays. The number 30 is choosen because of the used 30 pin cables. In general a simple inexpensive cable with twisted lines is sufficient to establish the connection. For displays with a digital 18 bit interface and low resolutions (VGA to SVGA) KONTRON offers a special adapter board (KAB-ADAPT-LVDStoTTL). This adapter needs an additional FLEX32 cable for the connection to the display (the order implies 2 article numbers). 2.2 JILI30 Cable Overview Please refer to the following matrix to choose the product that suits your needs best. The mentioned resolution is not binding as the cable could also be used for other resolutions - the panel connector is the most important part. 2.3 Article Number Designation Resolution Display (Example) 62514 KAB-JILI30-TXLD03 XGA (1024x768), 24 Bit SHARP LQ150X1LW71N 62517 KAB-JILI30-TELD02 SXGA (1280x1024), 24 Bit AUO M170EN07 62518 KAB-JILI30-TSLD01 SVGA (800x600), 18 Bit WVGA (800x480), 18 Bit AUO G104SN03 V2 PRIME VIEW PM070WL4 62520 KAB-JILI30-TXLD06 XGA (1024x768), 18 Bit OPTREX T51756D121J-FW 62524 KAB-JILI30-TXLD07 XGA (1024x768), 24 Bit NEC NL10276BC12-02 62526 KAB-JILI30-TSLD02 SVGA (800x600), 18 Bit SANYO TM121SV-02L07 KAB-ADAPT-LVDStoTTL Accessories Please refer to the following matrix to choose the product that suits your needs best. All displays that can be connected using a KAB-FLEX32 cable have a 18 bit digital interface (18 signal lines). Article Number Designation Resolution Display (Example) 61029 KAB-ADAPT-LVDStoTTL ---- ---- 64003 KAB-FLEX32-TSDD01 SVGA (800x600), left hand, 50 cm SHARP & NEC Panels 64006 KAB-FLEX32-TVDD03 VGA (640x480), left hand, 20 cm SHARP & NEC Panels 64007 KAB-FLEX32-TVDD04 VGA (640x480), right hand, 20 cm SHARP & NEC Panels 64008 KAB-FLEX32-TSDD03 SVGA (800x600), left hand, 20 cm SHARP & NEC Panels 64018 KAB-FLEX32-TVDD08 VGA (640x480), 20 cm LG PHILIPS LB064V02 64019 KAB-FLEX32-TQDD01 QVGA (320x240), 20 cm NEC NL3224BC35-20 64022 KAB-FLEX32-TVDD09 VGA (640x480), 20 cm LG PHILIPS LB104V03 64026 KAB-FLEX32-TSDD10 SVGA (800x600), 30 cm AUO A201SN02 Display Cable Guide KTD-S0018-0 3 Page 4 JILI30 Connector (SBC Side) JILI30 Connector (SBC Side) It's a single row connector with 30 contacts and 1.0 mm pitch (JAE, FI-X30S-HF or equivalent). Header 1 30 Pin Signal Name Function 1 FTX0- First channel data 0 output (negative) 2 FTX0+ First channel data 0 output (positive) 3 FTX1- First channel data 1 output (negative) 4 FTX1+ First channel data 1 output (positive) 5 FTX2- First channel data 2 output (negative) 6 FTX2+ First channel data 2 output (positive) 7 GND Ground 8 FTXC- First channel clock output (negative) 9 FTXC+ First channel clock output (positive) 10 FTX3- First channel data 3 output (negative) 11 FTX3+ First channel data 3 output (positive) 12 STX0- Second channel data 0 output (negative) 13 STX0+ Second channel data 0 output (positive) 14 GND Ground 15 STX1- Second channel data 1 output (negative) 16 STX1+ Second channel data 1 output (positive) 17 GND Ground 18 STX2- Second channel data 2 output (negative) 19 STX2+ Second channel data 2 output (positive) 20 STXC- Second channel clock output (negative) 21 STXC+ Second channel clock output (positive) 22 STX3- Second channel data 3 output (negative) 23 STX3+ Second channel data 3 output (positive) 24 GND Ground 25 SDA I2C data line 26 DATAENA Designator badly chosen - means: Panel power enable (power sequencing) 27 SCL I2C clock line 28 - 30 VCC Power +3.3V or +5.0V Display Cable Guide KTD-S0018-0 4 Page 5 JILI30 Cable (Examples) JILI30 Cable (Examples) The following chapter describes the wiring of a JILI30 cable on two examples. KONTRON recommends that the differential pairs should be twisted together to minimize crosstalk on the signal lines. It may seems as if JILI30 cables are made for a specific display resolution. This is only particularly true. The decision which cable can be used depends on the following criterias: 4.1 (R) Display connector type (R) Pinout of display connector (R) Number of channels/clocks (single or dual channel LVDS) (R) Color depth (18 or 24 bit) respectively number of LVDS data pairs KAB-JILI30-TXLD03 This cable can be used for single channel displays with 24 bit color depth (example SHARP LQ150X1LW71). Displays with an 18 bit single channel interface might also work depending on the color mapping of the display. Single Board Computer 300mm ( 10mm) Cabletype: AWG30, UL-Style 20744 and RoHS compatible 16 Wires Twisted-Flat wires (Color-Coded or color-marked Pin1-wire) Axx62514yww Pin1 Display Cable Guide Display-Side KTD-S0018-0 4.1.1 Page 6 JILI30 Cable (Examples) Display Connector Pinout Pinout table for the display SHARP LQ150X1LW71. 4.1.2 Pin Signal Name Function 1 VCC Power +3.3V 2 VCC Power +3.3V 3 GND Ground 4 GND Ground 5 TX0- Channel data 0 input (negative) 6 TX0+ Channel data 0 input (positive) 7 GND Ground 8 TX1- Channel data 1 input (negative) 9 TX1+ Channel data 1 input (positive) 10 GND Ground 11 TX2- Channel data 2 input (negative) 12 TX2+ Channel data 2 input (positive) 13 GND Ground 14 TXC- Channel clock input (negative) 15 TXC+ Channel clock input (positive) 16 GND Ground 17 TX3- Channel data 3 input (negative) 18 TX3+ Channel data 3 input (positive) 19 GND Ground 20 LVDS_SET Color mapping (FPDI or OpenLDI) Display Connector On the display side the connector HIROSE DF14H-20P is used. Display Cable Guide KTD-S0018-0 4.1.3 Page 7 JILI30 Cable (Examples) Cable Wiring The following drawing shows the detailed wiring. Display Single Board Computer 30 29 24 17 01 02 N.C. 03 04 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 05 06 07 08 09 14 10 11 4.2 Twisting-Table for this connection : 05 - 06 08 - 09 11 - 12 14 - 15 17 - 18 KAB-JILI30-TELD02 This cable can be used for dual channel displays with 24 bit color depth (example AU Optronics M170EN07). Display-Side Single Board Computer 300 mm (-0/+5mm) Pin1 UL - proof and RoHS compatible 27 wires Flat wires (Color-Coded) Axx62517yww R1 Cover resistor and leads with Tubing Heat Shrink. Display Cable Guide KTD-S0018-0 4.2.1 Page 8 JILI30 Cable (Examples) Display Connector Pinout Pinout table for display AU Optronics M170EN07. 4.2.2 Pin Signal Name Function 1 FTX0- First channel data 0 input (negative) 2 FTX0+ First channel data 0 input (positive) 3 FTX1- First channel data 1 input (negative) 4 FTX1+ First channel data 1 input (positive) 5 FTX2- First channel data 2 input (negative) 6 FTX2+ First channel data 2 input (positive) 7 GND Ground 8 FTXC- First channel clock input (negative) 9 FTXC+ First channel clock input (positive) 10 FTX3- First channel data 3 input (negative) 11 FTX3+ First channel data 3 input (positive) 12 STX0- Second channel data 0 input (negative) 13 STX0+ Second channel data 0 input (positive) 14 GND Ground 15 STX1- Second channel data 1 input (negative) 16 STX1+ Second channel data 1 input (positive) 17 GND Ground 18 STX2- Second channel data 2 input (negative) 19 STX2+ Second channel data 2 input (positive) 20 STXC- Second channel clock input (negative) 21 STXC+ Second channel clock input (positive) 22 STX3- Second channel data 3 input (negative) 23 STX3+ Second channel data 3 input (positive) 24 GND Ground 25 - 27 N. C. Not connected 28 - 30 VCC Power +5.0V Display Connector On the display side the connector JAE FI-X30H (Japan Aviation Electronics) is used. Display Cable Guide KTD-S0018-0 4.2.3 Page 9 JILI30 Cable (Examples) Cable Wiring The following drawing shows the detailed wiring. Display Single Board Computer 01 02 03 . . . .. . 1:1 ... 01 02 03 . . . 22 23 24 25 26 27 28 29 30 22 23 24 N.C. N.C. N.C. 28 29 30 Display Cable Guide Twisting-Table for this connection : 01 - 02 03 - 04 05 - 06 08 - 09 10 - 11 12 - 13 15 - 16 18 - 19 20 - 21 22 - 23 KTD-S0018-0 5 Page 10 KAB-ADAPT-LVDStoTTL KAB-ADAPT-LVDStoTTL The adapter has two connectors - one counter part of the JILI30 SBC connector and one for the KABFLEX32 cable. 5.1 JILI30 Connector The JILI30 interface of the KAB-ADAPT-LVDStoTTL uses only 3 LVDS data pairs so that only 18 bit displays can be driven. The following table shows the pinout. Header 1 30 Pin Signal Name Function 1 FTX0- First channel data 0 input (negative) 2 FTX0+ First channel data 0 input (positive) 3 FTX1- First channel data 1 input (negative) 4 FTX1+ First channel data 1 input (positive) 5 FTX2- First channel data 2 input (negative) 6 FTX2+ First channel data 2 input (positive) 7 GND Ground 8 FTXC- First channel clock input (negative) 9 FTXC+ First channel clock input (positive) 10 - 13 N. C. Not connected 14 GND Ground 15 - 16 N. C. Not connected 17 GND Ground 18 - 23 N. C. Not connected 24 GND Ground 25 N. C. Not connected 26 DATAENA Designator badly chosen - means: Panel power enable (power sequencing) 27 N. C. Not connected 28 - 30 VCC 1) Power +5.0V Display Cable Guide KTD-S0018-0 5.2 Page 11 KAB-ADAPT-LVDStoTTL FLEX32 Connector Through this connector the connection to the display is established. As the display connectors differ strongly KONTRON offers a set of prefabricated FLEX32 cables (see chapter 'KAB-ADAPT-LVDStoTTL accessories'). The table shows the pinout of the FLEX32 connector on the adapter board. Header 1 32 Pin Signal Name Function 1 GND Ground 2 CLK Clock output 3 HSYNC Horizontal sync output 4 VSYNC Vertical sync output 5 GND Ground 6 R0 Red data 0 output 7 R1 Red data 1 output 8 R2 Red data 2 output 9 R3 Red data 3 output 10 R4 Red data 4 output 11 R5 Red data 5 output 12 GND Ground 13 G0 Green data 0 output 14 G1 Green data 1 output 15 G2 Green data 2 output 16 G3 Green data 3 output 17 G4 Green data 4 output 18 G5 Green data 5 output 19 GND Ground 20 B0 Blue data 0 output 21 B1 Blue data 1 output 22 B2 Blue data 2 output 23 B3 Blue data 3 output 24 B4 Blue data 4 output 25 B5 Blue data 5 output 26 GND Ground 27 DE Data enable output 28 VCC Power +3.3V or +5.0V 29 VCC Power +3.3V or +5.0V 30 CONF0 Configurable pin 31 CONF1 Configurable pin 32 CONF2 Configurable pin Display Cable Guide KTD-S0018-0 5.3 Page 12 KAB-ADAPT-LVDStoTTL Power Supply The adapter KAB-ADAPT-LVDStoTTL must be driven with +5.0V DC. The adaption to a panel voltage of 3.3V is done on the adapter. The panel voltage can be set using solder jumpers. 5.3.1 Panel Power +3.3V This is the default setting. 5.3.2 Panel Power +5.0V Attention: Never set both solder jumper simultaneously! This can damage the adapter, the display and/or the SBC. Display Cable Guide KTD-S0018-0 5.4 Page 13 KAB-ADAPT-LVDStoTTL FLEX32 Configurable Pins Three configurable data lines of the FLEX32 cable allow the use of special panel features. Many displays have input pins for horizontal/vertical flipping respectively mirroring (signal name i.e. L_R and U_D). These lines can be set to VCC or GND through solder jumpers. Under no circumstances both solder jumpers may be set at the same time. The following table gives and overview: 5.5 Pin Designator Link to GND set Link to VCC set CONF0 R14 / R15 R14 R15 CONF1 R16 / R17 R16 R17 CONF2 R18 / R19 R18 R19 Electrical Specifications Supply Voltage (R) + 5.0V DC 5% Panel Current (maximal) (R) 600mA Ambient Temperature (R) 0 to +60C Display Cable Guide KTD-S0018-0 6 Page 14 FLEX32 Cable (Example) FLEX32 Cable (Example) This example shows the wiring of a FLEX32 cable. Due to relatively low frequencies it is not nessecary that the signal lines of the cable are twisted. A flatfoil cable is sufficient. 6.1 KAB-FLEX32-TVDD04 6.1.1 Display Connector Pinout Pinout table for a VGA display (example SHARP LQ10D42). Header 1 Pin Signal Name Function 1 GND Ground 2 CLK Clock input 3 HSYNC Horizontal sync input 4 VSYNC Vertical sync input 5 GND Ground 6 R0 Red data 0 input 7 R1 Red data 1 input 8 R2 Red data 2 input 9 R3 Red data 3 input 10 R4 Red data 4 input 11 R5 Red data 5 input 12 GND Ground 13 G0 Green data 0 input 14 G1 Green data 1 input 15 G2 Green data 2 input 16 G3 Green data 3 input 17 G4 Green data 4 input 18 G5 Green data 5 input 19 GND Ground 20 B0 Blue data 0 input 21 B1 Blue data 1 input 22 B2 Blue data 2 input 23 B3 Blue data 3 input 24 B4 Blue data 4 input 25 B5 Blue data 5 input 26 GND Ground 27 DE Data enable input 28 - 29 VCC Power +5.0V 30 R/L Horizontal display mode input 31 U/D Vertical display mode input Display Cable Guide KTD-S0018-0 6.1.2 Page 15 FLEX32 Cable (Example) Display Connector On the display side the connector HIROSE DF9B-31S-1V is used. 6.1.3 Cable Wiring The following drawing shows the detailed wiring. KAB-ADAPT-LVDStoTTL 01 02 03 . . . . . . . . . Display .. .. .. ... 1:1 .. .. .. .. . 01 02 03 . . . . . . . . . 29 30 31 29 30 N.C. Display Cable Guide KTD-S0018-0 Page 16 App. A: Schematic KAB-ADAPT-LVDStoTLL App. A: Schematic KAB-ADAPT-LVDStoTLL C10u C10 C10u C9 GND/ADJ 1 C11 C3u3 C10n C5 C8 C10u C7 C10u PLGND PLGND 20 12 48 42 36 28 PLVCC LVVCC VCC VCC VCC VCC Display Cable Guide LVGND LVGND LVGND GND GND GND GND GND 21 19 18 13 7 44 38 32 25 3 KTD-S0018-0 Page 17 Appendix B: Document Revision History Appendix B: Document Revision History Revision Date Author S0018-0 09/17/10 M. Huttmann Changes Created preliminary manual Corporate Offices Europe, Middle East & Africa North America Asia Pacific Oskar-von-Miller-Str. 1 85386 Eching/Munich Germany Tel.: +49 (0)8165/ 77 777 Fax: +49 (0)8165/ 77 219 info@kontron.com 14118 Stowe Drive Poway, CA 92064-7147 USA Tel.: +1 888 294 4558 Fax: +1 858 677 0898 info@us.kontron.com 17 Building,Block #1,ABP 188 Southern West 4th Ring Road Beijing 100070, P.R.China Tel.: + 86 10 63751188 Fax: + 86 10 83682438 info@kontron.cn Display Cable Guide