XTL1003-1 - RFM (RF Monolithics, Inc.)

www.RFM.com E-mail: info@rfm.com Page 1 of 6

13

C r y s t a l E q u i v a l e n t C i r c u i t

ESR

C

O

Electrical Characteristics

Characteristic Sym Notes Minimum Typical Maximum Units

Nominal Frequency 13.56000 MHz

Mode of Oscillation Fundamental

Storage Temperature Range, Crystal Only -50 +125 °C

Storage Temperature Range, in Tape and Reel -40 +85 °C

Operating Temperature Range -20 +70 °C

Frequency Stability over Operating Temperature Range ±20 ppm (referred to the value at 25 °C)

Frequency Make Tolerance FL±10 ppm @ 25 °C ±3 °C

Equivalent Series Resistance ESR 40 Ω

Shunt Capacitance CO2.0 pF

Motional Capacitance CM4.2 ±20% fF

Nominal Drive Level 10 µW

Load Capacitance CL13.5 pF

Insulation Resistance at 100 VDC 500 MΩ

Aging ±1.0 ppm/year @ 25 °C

Weight 0.037 ±0. 005 g

Stanard Shipping Quantity on 330 mm (13”) Reel 3000 units

Lid Symbolization (in addition to Lot and/or Date Codes) 1003-1 YWWS

SM5032-4 Case

CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.

Notes:

1. US and international patents may apply.

2. The design, manufacturing process, and specifications of this device are subject to change without notice.

3. RFM, stylized RFM logo , and RF Monolithics, Inc. are registered trademarks of RF Monolithics, In c.

XTL1003-1

13.56000 MHz

Crystal Unit

• Surface Mount Se am-Weld Package

• Good Frequency Stability over Temperatur e

• Excellent Reliability

• Complies with Directive 2002/95/EC (RoHS)

The XTL1003-1 is a surface mount 5.0 x 3.2 mm crystal unit for use in wireless

telecommunications devices, esp ecially where an ultra-miniature package is

needed for mobility.

P b

www.RFM.com E-mail: info@rfm.com Page 2 of 6

Dot indicates Pin 4

1.2 ±0.1

2.2 ±0.1

1.2 ±0.1

1.7 ±0.1

5 . 0 ± 0 . 1

3 . 2 ± 0 . 1

T o p V i e w

D o t i n d i c a t e s P i n 3 l o c a t i o n

0 . 8

± 0 . 1

S i d e V i e w

B o t t o m V i e w

P i n s 2 a n d 4 a r e

c o n n e c t e d t o t h e l i d

2 . 4 ± 0 . 2

1 . 2

± 0 . 1

1 . 4

± 0 . 2

43

21

0 . 8

± 0 . 1

D i m e n s i o n s a r e i n m m

Electrical Connections

Pin Connection

1COSC

2 GND (lid)

3FSKOUT

4 GND (lid)

4-Terminal Surface-Mount Seam Weld Case

5.0 x 3.2 mm Nominal Footprint

SM5032-4 Case

Footprint (mm)

Package Orientation in Carrier Tape

Pin 3

www.RFM.com E-mail: info@rfm.com Page 3 of 6

Reel Dimensions

Tape Dimensions

Notes:

1. Unless otherwise specified, tolerance on dimensions is ±0.1 mm

2. Material is black conductive polystyrene

3. 10 pitch cumulative tolerance is ±0.2 mm

www.RFM.com E-mail: info@rfm.com Page 4 of 6

Typical Reflo w Profile

0

5 0

1 0 0

1 5 0

2 0 0

2 5 0

3 0 0

0 6 0 1 2 0 1 8 0 2 4 0 3 0 0 3 6 0

T e m p e r a t u r e ( d e g C )

R a m p u p P r e h e a t R e f l o w C o o l D o w n

T i m e ( s e c o n d s )

Notes:

1. Maximum peak temperature: 265 degrees C for 8 to 12 seconds

2. Typical reflow temperature: 217 ±5 degrees C for 90 to 100 seconds

www.RFM.com E-mail: info@rfm.com Page 5 of 6

Packing - 3,000 units per reel ma ximum

www.RFM.com E-mail: info@rfm.com Page 6 of 6

R eliability Specifications Referenc e

standard

r esistanc e to Temp./ Duration : 260 ° C /10 secon ds ×2 times E IAJ E D-4701

S olde r ing heat Tot al time : 4 minutes (IR-ref low )

(I R ref low) -300(301)M(II)

Vibr ation Tot al p eak amplitude: 1.5 mm MIL-ST D 2 02F

Vibr ation f r equenc y: 10 t o 55 Hz met hod 201A

S weep per i od: 1.0 minut e

Vibr ation directions: 3 mutually per pendi c ular

Duration: 2 hours per direction

Mec hanic al Dir ec tions: 3 impac ts per axis MI L- S TD 202F

S hoc k Ac c elerat ion: 3000g's,

+

20/-0 % met hod 213C

Dur ation: 0.3 ms ( total 18 shocks)

Wav eform : Half-sine

S older abili t y S older T emper at u re: 265 ± 5°C MI L- S TD 883G

Dur at ion time: 5 ± 0. 5 seconds. met hod 2003

Thermal S hock Heat cycle c onditions MI L- S TD 883G

-55 ° C, 30 minut es <> 125 °C, 30 minut es met hod 1010.7

* cycle time : 10 times

Humidit y t est T emper at ur e: 70 ± 2 °C MI L- STD 202F

Relative humidity: 90~95% met hod 103B

Dur ation: 96 hour s

Dr y heat T emper at ur e: 125 ± 2 °C MI L- S TD 883G

( Aging t est ) Dur at ion: 168 hours met hod 1008.2

c ondition C

PCT test Pressure: 2.06 kg/cm2 (2.03*105 pa) E IAJ E D-4701-3

Temper ature : 121 ± 2 ° C B - 12 3A

Relative humidity : 100%

Dur ation: 24 hour s

Environmental characteristics

Mechanical characteristics

Test name Test process / method