HM70 Electrical / Environmental * Operating Temperature Range * Temperature Rise, Maximum * Operating Frequency High Power Shielded Low Profile Surface Mount Inductors -40C to +180C 50C Up to 400kHz S RomHpliant Co Specifications Inductance (1) (2) 100kHz, 0.1V DCR Isat @ 0 Adc @ Isat (mW) @ 25C (H 20%) (H) (Adc) Typ. Min. Typ. Typ. Max. Part Number HM70-101R0LF HM70-201R3LF HM70-201R9LF HM70-25R80LF HM70-301R5LF HM70-302R0LF HM70-31R65LF HM70-311R0LF HM70-321R3LF HM70-33R75LF HM70-341R3LF HM70-351R5LF HM70-401R2LF HM70-401R6LF HM70-431R9LF HM70-455R6LF HM70-50R70LF HM70-501R2LF HM70-505R0LF HM70-50100LF HM70-601R2LF HM70-602R0LF 1.00 1.33 1.94 0.83 1.50 2.10 0.65 1.00 1.30 0.75 1.30 1.50 1.20 1.60 1.90 5.60 0.70 1.20 5.00 10.0 1.20 2.00 0.63 0.93 1.28 0.488 0.80 1.12 0.48 0.60 0.80 0.50 0.80 0.97 0.92 1.15 1.50 4.45 0.40 0.80 3.60 6.80 0.80 1.20 0.70 1.16 1.60 0.61 1.00 1.40 0.54 0.90 1.00 0.61 1.00 1.20 1.02 1.44 1.70 5.00 0.52 0.90 4.30 8.00 1.00 1.60 2.53 3.38 4.71 1.75 2.16 3.48 1.80 2.16 2.16 1.40 2.16 4.00 1.75 2.13 2.00 5.00 1.05 1.68 6.50 12.0 1.37 2.20 2.90 3.74 5.42 2.01 2.48 4.00 2.50 2.48 2.48 1.50 2.48 4.50 1.80 2.36 2.20 6.00 1.26 2.00 8.00 15.0 1.58 2.60 16 16 12 18 16 12 16 16 16 16 20 18 18 20 15 8 30 24 7 7 20 15 (3) Core Loss Factor (4) Heating Current (Adc) T=50C K1 K2 Fig. 15 13 11 19 17 14 19 17 17 22 18 13 22 20 20 13 31 25 13 9 28 22 9.07E-11 1.24E-10 1.24E-10 1.51E-10 1.40E-10 1.53E-10 1.53E-10 1.53E-10 1.66E-10 1.53E-10 1.53E-10 1.35E-10 1.80E-10 1.67E-10 1.67E-10 1.67E-10 1.99E-10 1.99E-10 2.21E-10 2.21E-10 2.21E-10 2.21E-10 170.67 157.15 189.83 118.84 183.07 196.09 60.69 93.38 140.35 70.03 121.39 166.20 129.45 151.67 172.04 507.07 88.15 110.82 219.63 316.67 108.94 143.34 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 Notes: (1) DC resistance is measured at 25C. (2) The saturation current (Isat) is the current at which the inductance will be decreased by 20% from its initial (zero DC) value. (3) The heating current is the DC current, which causes the component temperature to increase by approximately 50C. This current is determined by soldering the component on a typical application PCB, and then applying the current to the device for 30 minutes. (4) Core Loss approximation is based on published core data: Core Loss (Pfe) = K1 * (f)1.338 * (K2I)2.2546 Where: core loss in watt f = frequency in kHz K1 and K2 = core loss factor I = delta I across the component in Amp. K2I = one half of the peak to peak flux density across the component in Gauss Packaging Standard: Embossed Tape & Reel Reel: Diameter: Capacity: Case size 10,20,25,30,31,32,33,34 Case size 35,40,43,45,50,60 www.bitechnologies.com = = = 13" (330.2mm) 500 Units 400 Units 2009/10 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE We reserve the right to change specifications without prior notice. 87 Electrical Characteristics @ 25C (A) Case size 10, 20, 25, 30 & 40 Inductance vs. Current Characteristics Inductance Rolloffvs. Current Characteristics (B) Case size 50 & 60 Inductance vs. Current Characteristics Inductance Rolloffvs. Current Characteristics 88 MAGNETIC COMPONENTS SELECTOR GUIDE 2009/10 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Outline Dimensions (mm) Figure 1 Top View Figure 2 Bottom View Note: Case size 10 20 25 30 31 32 33 34 35 40 43 45 50 60 A 9.00 9.00 9.00 9.00 9.00 9.00 9.00 9.00 10.7 11.0 10.1 10.1 13.5 14.0 Top View Recommended Solder Pad Layout Bottom View (1) Dummy terminal should not be used for any electrical connection. B 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.25 12.6 12.5 12.5 12.9 13.0 C 3.70 4.50 5.00 5.35 5.40 5.60 5.70 5.80 4.20 5.20 5.75 6.60 5.50 5.80 D 4.80 4.80 4.80 4.80 4.80 4.80 4.80 4.80 5.60 6.20 4.77 4.60 6.50 6.50 E 1.70 1.70 1.70 1.70 1.70 1.70 1.70 1.70 1.70 2.30 2.30 2.30 2.30 2.30 F 6.00 6.00 6.00 6.00 6.00 6.00 6.00 6.00 6.00 7.50 7.32 7.32 7.50 7.50 G 8.30 8.00 8.30 8.00 8.00 8.00 8.00 8.00 10.60 10.70 10.31 10.31 13.50 14.00 H 2.30 2.00 2.30 2.00 2.00 2.00 2.00 2.00 5.60 3.70 4.17 4.00 6.50 6.50 I 6.00 6.00 6.00 6.00 6.00 6.00 6.00 6.00 6.20 7.50 7.32 7.32 7.50 7.50 J 2.80 2.80 2.80 2.80 2.80 2.80 2.80 2.80 2.10 3.10 2.95 2.74 3.00 3.00 K 3.00 3.00 3.00 3.00 3.00 3.00 3.00 3.00 2.50 3.50 2.84 3.15 3.50 3.50 Ordering Information HM70 - 50 Model Series 1R2 Case Size LF TR13 Lead-Free TR - Tape & Reel Packing 13 - 13" reel Inductance Code: First 2 digits are significant. Last digit denotes the number of trailing zeros. For values below 10H, "R" denotes the decimal point. www.bitechnologies.com 2009/10 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE We reserve the right to change specifications without prior notice. 89