User's Guide SNVA675A - August 2012 - Revised April 2013 AN-2284 LM34926 Isolated Evaluation Board 1 Introduction An isolated bias supply is implemented in this evaluation board with LM34926 Constant-On-Time regulator. LM34926 regulator integrates both the high and low side power switches essential for creating isolated buck converter. Board Specifications: * Input Range: 20V to 100V * Primary Output Voltage: 10V * Secondary (Isolated) Output Voltage: 9.5V * Maximum Load Current (Primary + Secondary): 250mA * Maximum Power Output: 2.5W * Nominal Switching Frequency: 750kHz * Efficiency (FIN = 36V, IOUT2 = 250mA): 77 percent * Board size: 2 inch x 2 inch Figure 1. LM34926 Evaluation Board (Top View) All trademarks are the property of their respective owners. SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback AN-2284 LM34926 Isolated Evaluation Board Copyright (c) 2012-2013, Texas Instruments Incorporated 1 UVLO Threshold and Hysteresis 2 www.ti.com UVLO Threshold and Hysteresis The UVLO resistors are selected using the following two equations: VIN(HYS) = IHYSR1 (1) and VIN (UVLO,rising) = 1.225V x R1 * +1 (c) R2 (2) On this evaluation board R1 = 127k and R2 = 8.25k, resulting in UVLO rising threshold at VIN = 20.5V and a hysteresis of 2.54V. 2.1 Board Connection and Start-up The input connections are made using TP1 (VIN) and TP2 (GND) terminals. The primary output appears at TP3 (VOUT1) and TP4 (GND). The secondary (isolated) output is available across TP5 (VOUT2) and TP6 (IGND). The input voltage should be gradually increased above UVLO set point of 20.5V. Both the outputs (VOUT1 and VOUT2) should be close to 10V at this point. This board is designed to function with input voltage range of 20V to 100V. The minimum VIN threshold can be changed by changing the UVLO resistors R1, R2. VIN should not exceed 100V. The magnetics in this design is optimized for solution size, and therefore limits the output power. The total load at the output should not exceed 250mA, otherwise the coupled inductor will saturate/overheat, which can destroy both the coupled inductor and the regulator IC U1. If a sustained over-current situation is to be tolerated, a coupled inductor with higher saturation and rms ratings should be used. D1 + C4 1 F R10 2 NY VOUT2 9.5V (J3) SW (TP11) T1 IGND BST 2 20V-100V VIN (J1) 4 C1 + 1 F + R3 130 NY C5 0.1 F SW VIN 7 8 + 0.01 F C2 R8 RON LM34926 46.4 NY 47 H (1:1) 1000 pF R1 127 NY 3 VCC UVLO FB (TP7) R2 UVLO 8.25 NY EXP RTN 1 6 R4 7.32 NY D2 5 + U1 0Y R6 C7 C8 0.1 F + C3 1 F VOUT1 10V (J2) GND R5 1 NY C6 1 F Figure 2. Complete Evaluation Board Schematic 2 AN-2284 LM34926 Isolated Evaluation Board SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback Copyright (c) 2012-2013, Texas Instruments Incorporated Bill of Materials www.ti.com 3 Bill of Materials Table 1. Bill of Materials Item Description Mfg., Part Number Package Value U1 Sync Switching Regulator Texas Instruments, LM34926 WSON-8 100V, 300mA T1 Coupled Inductor, 1500 VDC Coilcraft, LPD5030V-473ME 5mm x 5mm 47uH, 0.47A Alternate Part Wurth, 750312750 8.26mm x 6.60mm 22uH, 0.76A Schottky Diode Diodes Inc., DFLS1100-7 Pwr-DI123 100V, 1A D1 D2 Schottky Diode Diodes Inc., SDM10U45-7 SOD-523 40V, 100mA C1 Ceramic Capacitor MuRata, GRM32CR72A105KA35L 1210 1uF, 100V, X7R C2 Ceramic Capacitor TDK, C1608X7R1C103K 0603 0.01uF, 16V, X7R C3, C4 Ceramic Capacitor TDK, C2012X7R1E105K 0805 1uF, 25V, X7R C5 Ceramic Capacitor Kemet, C0805C104K1RACTU 0805 0.1uF, 100V, X7R C6 Ceramic Capacitor TDK, C1608X7R1C105K 0603 1uF, 16V, X7R C7 Ceramic Capacitor Murata, GRM188R71E102KA01D 0603 1000pF,25V, X7R C8 Ceramic Capacitor AVX, 0603YC104KAT2A 0603 0.1uF, 16V, X7R R1 Resistor Vishay/Dale, CRCW0805127KFKEA 0805 127k, 1% R2 Resistor Vishay/Dale, CRCW08058K25FKEA 0805 8.25k, 1% R3 Resistor Vishay/Dale, CRCW0805130KFKEA 0805 130k, 1% R4 Resistor Panasonic, ERJ-3EKF7321V 0603 7.32k, 1% R5 Resistor Panasonic, ERJ-3EKF1001V 0603 1.0k,1% R6 Resistor Yageo, RC0603JR-070RL 0603 0 R8 Resistor Panasonic, ERJ-3EKF4642V 0603 46.4k, 1% R10 Resistor Panasonic, ERJ-6GEYJ202V 0805 2k, 5% SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback AN-2284 LM34926 Isolated Evaluation Board Copyright (c) 2012-2013, Texas Instruments Incorporated 3 Performance Curves 4 www.ti.com Performance Curves 100 EFFICIENCY (%) 90 VIN=36V VIN=24V 80 VIN=48V 70 60 VOUT2=10V, IOUT1=0 50 50 100 150 200 250 LOAD CURRENT (mA) 300 Figure 3. Efficiency at 750kHz, VOUT1=10V Figure 4. Steady State Waveform (VIN=48V, IOUT1=0mA, IOUT2= 100mA) Figure 5. Step Load Response (VIN=48V, IOUT1=0, Step Load on IOUT2=80mA-180mA) 4 AN-2284 LM34926 Isolated Evaluation Board SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback Copyright (c) 2012-2013, Texas Instruments Incorporated PC Board Layout www.ti.com 5 PC Board Layout Figure 6. Board Silkscreen SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback AN-2284 LM34926 Isolated Evaluation Board Copyright (c) 2012-2013, Texas Instruments Incorporated 5 PC Board Layout www.ti.com Figure 7. Board Top Layer 6 AN-2284 LM34926 Isolated Evaluation Board SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback Copyright (c) 2012-2013, Texas Instruments Incorporated PC Board Layout www.ti.com Figure 8. Board Bottom Layer SNVA675A - August 2012 - Revised April 2013 Submit Documentation Feedback AN-2284 LM34926 Isolated Evaluation Board Copyright (c) 2012-2013, Texas Instruments Incorporated 7 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM34926EVAL/NOPB